An improved data acquisition method for electrical impedance tomography.

Isaacson, Cheney and Seager have demonstrated that simultaneously applying trigonometric patterns of current to a circular electrode array optimizes the sensitivity of EIT to inner structure. We have found that it is less desirable to measure voltage at an electrode that also applies a current due to variable contact impedance. In order to preserve the optimum sensitivity while minimizing the effect of electrode artefacts, we have devised an approach where we sequentially apply a current between each individual electrode and a separate, fixed ground while measuring voltages at all other electrodes for each consecutive current impulse. By adding weighted sums of both the applied currents and corresponding measured voltages from individual passes, we can synthesize trigonometric patterns of any spatial frequency. Since only one of the electrodes in any given acquired data set is used as a source, this approach significantly dilutes the effect of contact impedance on the resulting voltage measurements. We present simulated data showing the equivalency between the synthesized and actual trigonometric excitation patterns. In addition, we report experimental data, both in vitro and in vivo, that show improved results using this data acquisition technique.

Dartmouth's next generation EIS system: preliminary hardware considerations.

Our previous system covered the frequency range of 0 to 1 MHz. In this new design we propose to cover the range from 0 to 10 MHz. The higher frequencies have forced us to reconsider several design decisions in view of both the physics of the problem and the performance of available electronic components. In this presentation we examine in detail the constraints faced by the designer, starting from wiring consideration to measurement techniques. We will also present the solutions we selected to overcome the limitations we discovered. The problems include phase detection, amplitude measurements, system organization and layout and finally system calibration.

Electrical impedance imaging at multiple frequencies in phantoms.

We have recently built and tested a 32 channel, multi-frequency (1 kHz to 1 MHz) voltage mode system to investigate electrical impedance spectroscopy (EIS) imaging. We completed a series of phantom experiments to define the baseline imaging performance of our system. Our phantom consisted of a plastic circular tank (20 cm diameter) filled with 0.9% aqueous NaCl solution. Conductors and nonconductors of decreasing width (W5: 3.4 cm, W4: 2.54 cm, W3: 0.95 cm, W2: 0.64 cm and WI: 0.32 cm) were positioned at various distances from the tank edge (1 cm, 2 cm, 4 cm and 8 cm). The results suggest that the detection of objects less than 1 cm in width is limited to the first 1 to 2 cm from the tank edge for absolute images, but this depth can extend to 8 cm in difference images. Larger 3.4 cm wide objects can be detected in absolute images at depths up to 8 cm from the tank edge. Generally, conductor images were clearer than their nonconductor counterparts. Not only did electrode artefacts lessen as the frequency increased, but the system's maximum resolution was attained at the highest operating frequencies. Although the system recovered the value of the electrical conductivity at the correct order of magnitude, it tended to smooth out large property discontinuities. The calculated electrical permittivity in these phantom studies was inconclusive due to the presence of electrode artefacts.

Multifrequency electrical impedance imaging: preliminary in vivo experience in breast.

We have deployed a recently completed spectroscopic electrical impedance tomography (EITS) imaging system in a small series of women (13 participants accrued to date) in order to investigate the feasibility of delivering EITS breast examinations on a routine basis. Hardware is driven with sinusoidally varying spatial patterns of applied voltage delivered to 16 electrodes over the 10 kHz to 1 MHz spectral range using a radially translating interface which couples the electrodes to the breast through direct contact. Imaging examinations have consisted of the acquisition of multi-channel measurements at ten frequencies on both breasts. Participants lie prone on an examination table with the breast to be imaged pendant in the electrode array that is located below the table. Examinations were comfortable and easy to deliver (about 10 minutes per breast including electrode-positioning time). Although localized near-surface electrode artefacts are evident in the acquired images, several findings have emerged. Permittivity images have generally been more informative than their conductivity counterparts, except in the case of fluid-filled cysts. Specifically, the mammographically normal breast appears to have characteristic absolute EITS permittivity and conductivity images that emerge across subjects. Structural features in the EITS images have correlated with limited clinical information available on participants with benign and malignant abnormality, cysts and scarring from previous lumpectomy and follow-up radiation therapy. Several cases from this preliminary experience are described.

A multichannel continuously selectable multifrequency electrical impedance spectroscopy measurement system.

There is increasing evidence that alterations in the electrical property spectrum of tissues below 10 MHz is diagnostic for tissue pathology and/or pathophysiology. Yet, the complexity associated with constructing a high-fidelity multichannel, multifrequency data acquisition instrument has limited widespread development of spectroscopic electrical impedance imaging concepts. To contribute to the relatively sparse experience with multichannel spectroscopy systems this paper reports on the design, realization and evaluation of a prototype 32-channel instrument. The salient features of the system include a continuously selectable driving frequency up to 1 MHz, either voltage or current source modes of operation and simultaneous measurement of both voltage and current on each channel in either of these driving configurations. Comparisons of performance with recently reported fixed-frequency systems is favorable. Volts dc (VDC) signal-to-noise ratios of 75-80 dB are achieved and the noise floor for ac signals is near 100 dB below the signal strength of interest at 10 kHz and 60 dB down at 1 MHz. The added benefit of being able to record multispectral information on source and sense signal amplitudes and phases has also been realized. Phase-sensitive detection schemes and multiperiod undersampling techniques have been deployed to ensure measurement fidelity over the full bandwidth of system operation.