RESUMO
We report the effect of integrating metasurface-aided reconfigurable intelligent surfaces (RISs) on the signal-to-interference-plus-noise ratio (SINR) and data rate of a multi-cell visible light communication (VLC) system. RIS has been deployed in the channel between transmitter and receiver to redirect the reflected light in the desired directions, even in the absence of line-of-sight (LoS) links. Results show that the introduction of RIS has improved average SINR but reduced average illumination level compared to a no-RIS system. As the quantity of RIS increases, a discernible improvement in the maximum SINR value is observed. Here, three different receiver geometries, namely, a photodiode (PD), freeform diversity receiver (FDR), and modified FDR (MFDR), have been adopted. The impact of individual receivers has been reported in the presence of light path blockage. MFDR geometry is found to be most suitable with more coverage probability compared to the other two receivers. With (40c m×24c m) RIS area, during blockage, MFDR maintains an average SINR of 21.95 dB, which is 97.29% and 14.24% greater than PD and FDR, respectively.
RESUMO
The manufacturing and characterization of freeform optical surfaces are influenced by their high sensitivity to misalignments. In this work, the computational sampling moiré technique combined with phase extraction is developed for the precise alignment of freeform optics during fabrication and in metrology applications. This novel, to the best of our knowledge, technique achieves near-interferometry-level precision in a simple and compact configuration. This robust technology can be applied to industrial manufacturing platforms (such as diamond turning machines, lithography, and other micro-nano-machining techniques) as well as their metrology equipment. In a demonstration of computational data processing and precision alignment using this method, iterative manufacturing of freeform optical surfaces with a final-form accuracy of about 180â nm was accomplished.
RESUMO
In the present work, a spline-based integration technique for the reconstruction of a freeform wavefront from the slope data has been implemented. The slope data of a freeform surface contain noise due to their machining process and that introduces reconstruction error. We have proposed a weighted cubic spline based least square integration method (WCSLI) for the faithful reconstruction of a wavefront from noisy slope data. In the proposed method, the measured slope data are fitted into a piecewise polynomial. The fitted coefficients are determined by using a smoothing cubic spline fitting method. The smoothing parameter locally assigns relative weight to the fitted slope data. The fitted slope data are then integrated using the standard least squares technique to reconstruct the freeform wavefront. Simulation studies show the improved result using the proposed technique as compared to the existing cubic spline-based integration (CSLI) and the Southwell methods. The proposed reconstruction method has been experimentally implemented to a subaperture stitching-based measurement of a freeform wavefront using a scanning Shack-Hartmann sensor. The boundary artifacts are minimal in WCSLI which improves the subaperture stitching accuracy and demonstrates an improved Shack-Hartmann sensor for freeform metrology application.
RESUMO
In this paper, the effect of magnetic fields on the temperature and temperature profile of a diffusion flame obtained from a butane torch burner are investigated experimentally by using digital speckle pattern interferometry (DSPI). Experiments were conducted on a diffusion flame generated by a butane torch burner in the absence of a magnetic field and in the presence of uniform and nonuniform magnetic fields. A single DSPI fringe pattern was used to extract phase by using a Riesz transform and monogenic signal. Temperature inside the flame was determined experimentally both in the absence and in the presence of magnetic fields. Experimental results reveal that the maximum temperature of the flame is increased under the influence of an upward-decreasing magnetic gradient and decreased under an upward-increasing magnetic gradient while a negligible effect on temperature in a uniform magnetic field was observed.
RESUMO
A method based on subaperture stitching for measurement of a freeform wavefront is proposed and applied to wavefronts calculated from the slope data acquired using a scanning Shack Hartmann sensor (SHS). The entire wavefront is divided into a number of subapertures with overlapping zones. Each subaperture is measured using the SHS, which is scanned over the entire wavefront. The slope values and thus the phase values of separately measured subapertures cannot be connected directly due to various misalignment errors during the scanning process. The errors lying in the vertical plane, i.e., piston, tilt, and power, are minimized by fitting them in the overlapping zone. The radial and rotational misalignment errors are minimized during registration in the global frame by using active numerical alignment before the stitching process. A mathematical model for a stitching algorithm is developed. Simulation studies are presented based on the mathematical model. The proposed mathematical model is experimentally verified on freeform surfaces of a cubic phase profile.
RESUMO
Aspheric optical surfaces are often tested using diffractive optics as null elements. For precise measurements, the errors caused by the diffractive optical element must be calibrated. Recently, we reported first experimental results of a three position quasi-absolute test for rotationally invariant aspherics by using combined-diffractive optical elements (combo-DOEs). Here we investigate the effects of the DOE substrate errors on the proposed calibration procedure and present a set of criteria for designing an optimized combo-DOE. It is demonstrated that this optimized design enhances the overall consistency of the procedure. Furthermore, the rotationally varying part of the surface deviations is compared with the rotationally varying deviations obtained by an N-position averaging procedure and is found to be in good agreement.