Fabrication of Vertical MEMS Actuator with Hollow Square Electrode for SPR Sensing Applications.

In this study, an electrostatically driven vertical MEMS actuator was designed using a hollow square electrode. To attain vertical actuation, a hollow square-shaped electrode was designed on the glass substrate. The silicon proof mass, containing a step, was utilized to realize analogue actuation without pull-in. The vertical MEMS actuator was fabricated using the SiOG (Silicon on Glass) process and the total actuator size was 8.3 mm × 8.3 mm. The fabricated proof mass was freestanding due to eight serpentine springs with 30 µm width. The vertical movement of the MEMS actuator was successfully controlled electrostatically. The measured vertical movement was 5.6 µm for a voltage of 40 V, applied between the top silicon structure and the hollow square electrode. The results shown here confirm that the proposed MEMS actuator was able to control the vertical displacement using an applied voltage.

Reconfigurable broadband metasurfaces with nearly perfect absorption and high efficiency polarization conversion in THz range.

Reconfigurable metasurfaces (RMSs) that enable the switching function of absorption and polarization conversion have attracted increasing attention. However, the design of RMSs to achieve wideband and high efficiency for both absorption and polarization conversion functions simultaneously remains a great challenge. Here, we propose the design of a RMS structure with a high-efficiency cross-polarization conversion and nearly perfect absorption. The reconfiguration between different functions of polarization conversion and absorption is obtained based on the reversible insulator-to-metal phase transition of Vanadium dioxide (VO[Formula: see text]). When the VO[Formula: see text] is in insulator state, the RMS realizes the cross-polarization conversion function in the wideband of 1.04-3.75 THz with a relative bandwidth up to 113 [Formula: see text] due to the multi-resonant modes of electric and magnetic resonances. Meanwhile, the nearly-perfect absorption is achieved in the range of 1.36-3.38 THz with the corresponding relative bandwidth up to 85 [Formula: see text] for the VO[Formula: see text] in metallic state. Specially, the wideband and high-efficiency performance of these functionalities is maintained for a wide angle incidence. The capability of bi-functional switch and integration with polarization conversion and absorption in a single metasurface structure endowed with both wideband and high-efficiency characteristics for a wide incident angle is very promising for emerging RMS devices in the terahertz region.

Precise control over the silica shell thickness and finding the optimal thickness for the peak heat diffusion property of AuNR@SiO2.

Silica-coated gold nanorods (AuNRs) exhibit significantly enhanced photothermal effects and photoacoustic (PA) signal intensities, which is beneficial for various nanophotonic applications in materials science. However, the silica shell thickness for optimum enhancement is not fully understood and is even controversial depending on the physical state of the silica shell. This is because of the lack of systematic investigations of the nanoscale silica shell thickness and the photothermal effect. This study provides a robust synthetic method to control the silica shell thickness at the nanoscale and the physical state-dependent heat diffusion property. The selected base and solvent system enabled the production of silica-coated AuNRs (AuNR@SiO2) with silica shell thicknesses of 5, 10, 15, 20, 25, 30, 35, and 40 nm. AuNRs with a 20 nm silica shell showed the highest photothermal effect with a 1.45-times higher photothermal efficiency than that of AuNRs without a silica shell. The low density of the silica shell on the AuNRs showed a low photothermal effect and photostability. It was found that the disruption of cetyltrimethyl ammonium bromide (CTAB) layers on the AuNRs was responsible for the low photostability of the AuNRs. The simulation study for the heat diffusion property showed facilitated heat diffusion in the presence of a 20 nm silica shell. In a cell-based study, AuNRs with a 20 nm silica shell showed the most sensitive photothermal effect for cell death. The results of this robust study can provide conclusive conditions for the optimal silica shell thickness to obtain the highest photothermal effect, which will be useful for the future design of nanomaterials in various fields of application.

Dual Light Trapping and Water-Repellent Effects of a Flexible-Based Inverse Micro-Cone Array for Organic and Perovskite Solar Cells.

A simple and cost-effective fabrication process of a flexible-based inverse micro-cone array (i-MCA) structure textured on flexible transparent conductive electrodes (TCEs) was successfully demonstrated via a micro-imprinting process. The flexible i-MCA films exhibited an extremely high total transmittance of ∼93% and a haze of ∼95% with reduced reflectance while simultaneously demonstrating water-repellent properties. Introducing i-MCA on the illuminating side of organic solar cells (OSCs)- and perovskite solar cells-rigid glass substrate showed improved power conversion efficiencies (PCEs) due to the light trapping effect by multiple light bounces between cone array structures (forward scattering). This results in an increase of the optical path length in the photoactive layer. Similarly, flexible TCEs embedded with textured i-MCA increased the PCE by 14% for flexible OSCs. More importantly, i-MCA-TCE-based OSCs were highly flexible with 98% retention from the initial PCE at both 0° and at 60° even after 2000 bending cycles at a radius of 2 mm. This finding demonstrates that textured i-MCA is promising for improving: (a) the light harvesting efficiency of solar cells when installed in low-/high-latitude locations and (b) the wearable technology where a flexible device attached on curved objects could retain the PCE, even at an oblique angle, with respect to the normal incidence angle.

Plasmonic Effect of Gold Nanostars in Highly Efficient Organic and Perovskite Solar Cells.

Herein, a novel strategy is presented for enhancing light absorption by incorporating gold nanostars (Au NSs) into both the active layer of organic solar cells (OSCs) and the rear-contact hole transport layer of perovskite solar cells (PSCs). We demonstrate that the power conversion efficiencies of OSCs and PSCs with embedded Au NSs are improved by 6 and 14%, respectively. We find that pegylated Au NSs are greatly dispersable in a chlorobenzene solvent, which enabled complete blending of Au NSs with the active layer. The plasmonic contributions and accelerated charge transfer are believed to improve the short-circuit current density and the fill factor. This study demonstrates the roles of plasmonic nanoparticles in the improved optical absorption, where the improvement in OSCs was attributed to surface plasmon resonance (SPR) and in PSCs was attributed to both SPR and the backscattering effect. Additionally, devices including Au NSs exhibited a better charge separation/transfer, reduced charge recombination rate, and efficient charge transport. This work provides a comprehensive understanding of the roles of plasmonic Au NS particles in OSCs and PSCs, including an insightful approach for the further development of high-performance optoelectronic devices.

Microfabricated Otto chip device for surface plasmon resonance-based optical sensing.

Surface plasmon resonance (SPR) based sensors are usually designed using the Kretschmann prism coupling configuration in which an input beam couples with a surface plasmon through a thin metal film. This is generally preferred by sensor developers for building planar devices instead of the Otto prism coupling configuration, which, for efficient coupling, requires the metal surface to be maintained at a distance on the order of the wavelength from the input prism surface. In this paper, we report on the microfabrication and characterization of an Otto chip device, which is suitable for applications of the SPR effect in gas sensing and biosensing.

Amplified photoacoustic performance and enhanced photothermal stability of reduced graphene oxide coated gold nanorods for sensitive photoacoustic imaging.

We report a strongly amplified photoacoustic (PA) performance of the new functional hybrid material composed of reduced graphene oxide and gold nanorods. Due to the excellent NIR light absorption properties of the reduced graphene oxide coated gold nanorods (r-GO-AuNRs) and highly efficient heat transfer process through the reduced graphene oxide layer, r-GO-AuNRs exhibit excellent photothermal stability and significantly higher photoacoustic amplitudes than those of bare-AuNRs, nonreduced graphene oxide coated AuNRs (GO-AuNRs), or silica-coated AuNR, as demonstrated in both in vitro and in vivo systems. The linear response of PA amplitude from reduced state controlled GO on AuNR indicates the critical role of GO for a strong photothermal effect of r-GO-AuNRs. Theoretical studies with finite-element-method lab-based simulation reveal that a 4 times higher magnitude of the enhanced electromagnetic field around r-GO-AuNRs can be generated compared with bare AuNRs or GO-AuNRs. Furthermore, the r-GO-AuNRs are expected to be a promising deep-tissue imaging probe because of extraordinarily high PA amplitudes in the 4-11 MHz operating frequency of an ultrasound transducer. Therefore, the r-GO-AuNRs can be a useful imaging probe for highly sensitive photoacoustic images and NIR sensitive therapeutics based on a strong photothermal effect.