Synthesis and Thermo-Responsive Behavior of Poly(N-isopropylacrylamide)-b-Poly(N-vinylisobutyramide) Diblock Copolymer.

Thermo-responsive diblock copolymer, poly(N-isopropylacrylamide)-block-poly(N-vinylisobutyramide) was synthesized via switchable reversible addition-fragmentation chain transfer (RAFT) polymerization and its thermal transition behavior was studied. Poly(N-vinylisobutyramide) (PNVIBA), a structural isomer of poly(N-isopropylacrylamide) (PNIPAM) shows a thermo-response character but with a higher lower critical solution temperature (LCST) than PNIPAM. The chain extension of the PNVIBA block from the PNIPAM block proceeded in a controlled manner with a switchable chain transfer reagent, methyl 2-[methyl(4-pyridinyl)carbamothioylthio]propionate. In an aqueous solution, the diblock copolymer shows a thermo-responsive behavior but with a single LCST close to the LCST of PNVIBA, indicating that the interaction between the PNIPAM segment and the PNVIBA segment leads to cooperative aggregation during the self-assembly induced phase separation of the diblock copolymer in solution. Above the LCST of the PNIPAM block, the polymer chains begin to collapse, forming small aggregates, but further aggregation stumbled due to the PNVIBA segment of the diblock copolymer. However, as the temperature approached the LCST of the PNVIBA block, larger aggregates composed of clusters of small aggregates formed, resulting in an opaque solution.

Rational Design of Naphthol Groups Functionalized Bipolar Polymer Cathodes for High Performance Alkali-Ion Batteries.

Redox-active organic compounds gather significant attention for their potential application as electrodes in alkali ion batteries, owing to the structural versatility, environmental friendliness, and cost-effectiveness. However, their practical applications of such compounds are impeded by insufficient active sites with limited capacity, dissolution in electrolytes, and sluggish kinetics. To address these issues, a naphthol group-containing triarylamine polymer, namely poly[6,6'-(phenylazanediyl)bis(naphthol)] (poly(DNap-OH)) is rationally designed and synthesized, via oxidative coupling polymerization. It is capable of endowing favorable steric structures that facilitate fast ion diffusion, excellent chemical stability in organic electrolytes, and additional redox-active sites that enable a bipolar redox reaction. By exploiting these advantages, poly(DNap-OH) cathodes demonstrate remarkable cycling stability in both lithium-ion batteries (LIBs) and potassium-ion batteries (PIBs), showcasing enhanced specific capacity and redox reaction kinetics in comparison to the conventional poly(4-methyltriphenylamine) cathodes. Overall, this work offers insights into molecular design strategies for the development of high-performance organic cathodes in alkali-ion batteries.

Influence of Different Metal Types on the Bonding Strength of Concrete Using the Arc Thermal Metal Spraying Method.

Exterior finishes protect reinforced concrete buildings against environmental factors, improve their durability, and enhance their exterior design. In this study, the influence of different metal types used in arc thermal metal spraying on the adhesion between concrete and metal coatings was analyzed. Five metals with different melting points were tested, and the differences between their melting points and surface temperatures immediately after thermal spraying were measured. The bonding strength of each metal was evaluated. Additionally, the interface between the concrete surface and metal coating was analyzed using image analysis and optical microscopy. The results demonstrated that Zn achieved the highest bonding strength (1.84 MPa), which had the lowest melting point and surface temperature immediately after spraying, while Cu/Sn achieved the lowest strength (1.38 MPa), which had the highest temperatures. The bonding strength had a closer relationship (R2 = 0.9946) with the difference between the melting point and surface temperature immediately after spraying than that (R2 = 0.9589) with the surface temperature immediately after spraying. The bonding strength increased as the ratio of the non-interfacial failure area to the total area increased, ensuring a stronger attachment to the concrete surface. Overall, the results showed that the bonding strength was significantly affected by the metal type.

Electrochemical Cloud Point Temperature from Thermoamperometry: Real-Time Analysis for Phase Transition of Thermoresponsive Polymers.

Cloud point temperature (Tcp) is a thermal index used to define the phase transition of thermoresponsive polymers. In this study, we used electrochemical techniques to obtain an electrochemical cloud point temperature (Tecp) that exhibits the more accurate phase transition temperature and can replace Tcp. Thermoamperometry on an ultramicroelectrode was conducted with a poly(arylene ether sulfone) (PES10) as a model system to obtain a current-temperature (i-T) curve in real time; the Tecp of the PES10 was determined from the i-T curve. The i-T curve shows an unprecedented current decrease in the PES10 solution despite increasing temperature; on the other hand, the current increased linearly with increasing temperature in the solution without PES10. This phenomenon was analyzed by considering the characteristics of PES10 during phase transition, such as dynamic viscosity, temperature of the solution, and electrode impedance. It was confirmed that the current drops shown in the i-T curves were mainly due to the decrease of real electrode area. The comparison of Tecp and Tcp showed that both depended similarly on the concentrations of the thermoresponsive polymer and the supporting electrolyte. The results reveal that by adjusting the concentration of polymer and electrolyte in an organic solution, Tecp, as a new analytical method, can be used in electric circuit-based energy storage appliances such as Li-ion batteries and supercapacitors.

Simple and rapid electrochemical monitoring for depolymerization of polyamic acid.

Excellent thermal and mechanical properties of aromatic polyimides (PIs) make them attractive materials in various fields. PIs is performed using polyamic acid (PAA) precursors due to their limited solubility. However, PAAs can be easily depolymerized by moisture and heat, which can degrade the properties of PIs. Therefore, quality control of PAAs is an important task in researches and industrial applications. Here, we propose a simple, rapid, and novel method to observe the depolymerization of PAAs. The method is based on the principle that, as the molecular weight of the polymer decreases, the solution viscosity decreases, and the viscosity of the solution can be easily and rapidly measured using electrochemistry. We accelerated depolymerization by applying heat to a PAA solution and measured the change in viscosity of the solution through cyclic voltammetry. The proposed method, which also makes it possible to determine the dynamic viscosity of a polymer solution, is presented as a model system to observe state changes in various polymers.

Synthesis and CO2 Capture of Porous Hydrogel Particles Consisting of Hyperbranched Poly(amidoamine)s.

We successfully synthesized new macroporous hydrogel particles consisting of hyperbranched poly(amidoamine)s (HPAMAM) using the Oil-in-Water-in-Oil (O/W/O) suspension polymerization method at both the 50 mL flask scale and the 5 L reactor scale. The pore sizes and particle sizes were easily tuned by controlling the agitation speeds during the polymerization reaction. Since O/W/O suspension polymerization gives porous architecture to the microparticles, synthesized hydrogel particles having abundant amine groups inside polymers exhibited a high CO2 absorption capacity (104 mg/g) and a fast absorption rate in a packed-column test.

Highly Transparent Aromatic Polyamides from Unsymmetrical Diamine with Trifluoromethyl Groups.

Soluble and transparent wholly aromatic polyamides (PAs) were synthesized from an unsymmetrical diamine monomer having trifluoromethyl (CF3) groups, 4-(4'-aminophenoxy)-3,5-bis(trifluoromethyl)aniline. The monomer was polymerized with several dicarboxylic acid monomers via the Yamazaki-Higashi polycondensation method. All of the synthesized polyamides have an amorphous morphology, and they are soluble in many polar organic solvents at room temperature. Flexible and transparent films of the polyamides were prepared by solution casting and these polymer films show good optical transparencies with cut-off wavelengths of 337-367 nm and transparencies of 88%-90% at 550 nm. In addition, all the polymers were thermally stable over 400 °C and exhibited glass transition temperatures (Tg) higher than 300 °C. Unsymmetrically inserted trifluoromethyl groups on polyamides improves the solubility as well as the transparency of the polymers while maintaining good thermal properties. They also showed low refractive indices around 1.5333~1.5833 at 633 nm owing to the existence of low polarizable trifluoromethyl groups.

Soluble Poly(amide-imide)s from Diamide-Diamine Monomer with Trifluoromethyl Groups.

A series of soluble aromatic poly(amide-imide)s (PAIs) was prepared from a new diamide-diamine monomer having biphenyl units with two CF3 groups. The diamide-diamine monomer was polymerized with 2,2'-bis(trifluoromethyl)benzidine and pyromelltic dianhydride through an imidization reaction to prepare PAIs with a controlled imide/amide bond ratio in the main chains. While the PAIs with the highest imide bond content showed a limited solubility, other PAIs were soluble in polar organic solvents and can be solution-cast into flexible freestanding films. All PAIs exhibited high thermal stability with 5% weight loss temperature (Td5) from 464 to 497 °C in air, and no appearance of glass transition up to 400 °C. Notably, the linear coefficient of thermal expansion (CTE) value of the PAI films was linearly decreased with the imide bond content and varied from 44.8 to 7.8 ppm/°C.

Synthesis of Arylene Ether-Type Hyperbranched Poly(triphenylamine) for Lithium Battery Cathodes.

We synthesized a new poly(triphenylamine), having a hyperbranched structure, and employed it in lithium-ion batteries as an organic cathode material. Two types of monomers were prepared with hydroxyl groups and nitro leaving groups, activated by a trifluoromethyl substituent, and then polymerized via the nucleophilic aromatic substitution reaction. The reactivity of the monomers differed depending on the number of hydroxyl groups and the A2B type monomer with one hydroxyl group successfully produced poly(triphenylamine). Based on thermal, optical, and electrochemical analyses, a composite poly(triphenylamine) electrode was made. The electrochemical performance investigations confirmed that the lithium-ion batteries, fabricated with the poly(triphenylamine)-based cathodes, had reasonable specific capacity values and stable cycling performance, suggesting the potential of this hyperbranched polymer in cathode materials for lithium-ion batteries.

Poly (Amidehydrazide) Hydrogel Particles for Removal of Cu2+ and Cd2+ Ions from Water.

Poly(amidoamine)s (PAMAM) are very effective in the removal of heavy metal ions from water due to their abundant amine and amide functional groups, which have a high binding ability to heavy metal ions. We synthesized a new class of hyperbranched poly(amidehydrazide) (PAMH) hydrogel particles from dihydrazides and N,N'-methylenebisacrylamide (MBA) monomer by using the A2 + B4 polycondensation reaction in an inverse suspension polymerization process. In Cd2+ and Cu2+ ion sorption tests, the synthesized dihydrazide-based PAMH hydrogel particles exhibited sorption capacities of 85 mg/g for copper and 47 mg/g for cadmium. Interestingly, the PAMH showed only a 10% decrease in sorption ability in an acidic condition (pH = 4) compared to the diamine-based hyperbranched PAMAM, which showed a ~90% decrease in sorption ability at pH of 4. In addition, PAMH hydrogel particles remove trace amounts of copper (0.67 ppm) and cadmium (0.5 ppm) in water, below the detection limit.

Well-Defined Dual Light- and Thermo-Responsive Rod-Coil Block Copolymers Containing an Azobenzene, MEO2MA and OEGMA.

Here we report the dual light- and thermo-responsive behavior of well-defined rod-coil block copolymers composed of an azobenzene unit, 2-(2-methoxyethoxy)ethyl methacrylate (MEO2MA) and oligo(ethylene glycol) methacrylate (OEGMA). Azobenzene-containing rigid rod blocks prepared by chain growth condensation polymerization of the azobenzene containing monomer were used as a macroinitiator of atom transfer radical polymerization (ATRP) after attaching an α-bromoisobutyryl group as an end group. Synthesis of well-defined rod-coil block copolymers with different coil block lengths was achieved by copolymerization of MEO2MA and OEGMA monomers. The synthesized polymers exhibited amphiphilic properties and polymeric micelles were formed in aqueous solution. The light-responsive behaviors of azobenzene moieties, photoisomerization by irradiation of light, and thermo-responsive behaviors of P(MEO2MA-co-OEGMA) coil blocks, aggregation by increment of temperature over lower critical solution temperature, were investigated. A dual stimuli-responsive behavior of the rod-coil block copolymers was observed when exposed to light and heat.

Homochiral Supramolecular Thin Film from Self-Assembly of Achiral Triarylamine Molecules by Circularly Polarized Light.

Here, we report the formation of homochiral supramolecular thin film from achiral molecules, by using circularly polarized light (CPL) only as a chiral source, on the condition that irradiation of CPL does not induce a photochemical change of the achiral molecules. Thin films of self-assembled structures consisting of chiral supramolecular fibrils was obtained from the triarylamine derivatives through evaporation of the self-assembled triarylamine solution. The homochiral supramolecular helices with the desired handedness was achieved by irradiation of circularly polarized visible light during the self-assembly process, and the chiral stability of supramolecular self-assembled product was achieved by photopolymerization of the diacetylene moieties at side chains of the building blocks, with irradiation of circularly polarized ultraviolet light. This work provides a novel methodology for the generation of homochiral supramolecular thin film from the corresponding achiral molecules.

Copper Ions Removal from Water using A2B3 Type Hyperbranched Poly(amidoamine) Hydrogel Particles.

Micrometer-sized hyperbranched poly(amidoamine) (hPAMAM) particles are prepared with a simple A2B3 type Aza-Michael addition reaction between aminoethylpiperazine (AEP) and methylenebisacrylamide (MBA) in an inverse suspension polymerization condition. The synthesized particles exhibited surprisingly high Cu2+ sorption capacity (0.223g/g) for a solid-type absorbent. In addition to the high sorption ability of the particle, its simple synthetic process and convenience, due to its micrometer-sized spherical shape and recyclability, make it a practical and attractive absorbent for heavy metal ion removal from aqueous solutions.

Poly(amide-imide) materials for transparent and flexible displays.

The key component currently missing for the next generation of transparent and flexible displays is a high-performance polymer material that is flexible, while showing optical and thermal properties of glass. It must be transparent to visible light and show a low coefficient of thermal expansion (CTE). While specialty plastics such as aromatic polyimides are promising, reducing their CTE and improving transparency simultaneously proved challenging, with increasing coloration the main problem to be resolved. We report a new poly(amide-imide) material that is flexible and displays glass-like behavior with a CTE value of 4 parts per million/°C. This novel polymer was successfully used as a substrate to fabricate transparent and flexible indium-gallium-zinc oxide thin-film transistors.

Observing Phase Transition of a Temperature-Responsive Polymer Using Electrochemical Collisions on an Ultramicroelectrode.

Herein, a study on a new lower critical solution temperature (LCST) polymer in an organic solvent by an electrochemical technique has been reported. The phase-transition behavior of poly(arylene ether sulfone) (PAES) was examined on 1,2-dimethoxyethane (DME). At a temperature above the LCST point, polymer molecules aggregated to create polymer droplets. These droplets subsequently collided with an ultramicroelectrode (UME), resulting in a new form of staircase current decrease. The experimental collision frequency and collision signal were analyzed in relation to the concentration of the polymer. In addition, the degree of polymer aggregation associated with temperature change was also observed.

Micro-hydrogel Particles Consisting of Hyperbranched Polyamidoamine for the Removal of Heavy Metal Ions from Water.

A series of micro-hydrogel particles consisting of hyperbranched polyamidoamine (HPAMAM) without any supporting core materials was synthesized via the inverse suspension condensation polymerization of A2 and B4 monomers, N,N'-methylenebisacrylamide (MBA) and ethylenediamine (EDA). The particles were found to be highly effective when used to remove heavy metal ions, such as cadmium, copper, lead, nickel, zinc, and cobalt, from water, and they could be separated from the water by a simple filtration process. The results of this study demonstrate that crosslinked HPAMAM particles, which can be prepared by a simple and environmentally friendly process, are an attractive absorbent for water purification.

Highly Efficient Visible Blue-Emitting Black Phosphorus Quantum Dot: Mussel-Inspired Surface Functionalization for Bioapplications.

The preparation of blue-emitting black phosphorus quantum dots (BPQDs) is based on the liquid-phase exfoliation of bulk BP. We report the synthesis of soluble BPQDs showing a strong visible blue-light emission. Highly fluorescent (photoluminescence quantum yield of ≈5% with the maximum emission (λmax) at ≈437 nm) and dispersible BPQDs in various organic solvents are first prepared by simple ultrasonication of BP crystals in chloroform in the ambient atmosphere. Furthermore, simple mussel-inspired surface functionalization of BPQDs with catechol-grafted poly(ethylene glycol) in basic buffer afforded water-soluble blue-emitting BPQDs showing long-term fluorescence stability, very low cytotoxicity, and excellent fluorescence live cell imaging capability.

Remarkably enhanced adhesion of coherently aligned catechol-terminated molecules on ultraclean ultraflat gold nanoplates.

We report the characterization and formation of catechol-terminated molecules immobilized on gold nanoplates (Au NPLs) using N-(3,4-dihydroxyphenethyl)-2-mercaptoacetamide (Cat-EAA-SH). Single-crystalline Au NPLs, synthesized using a one-step chemical vapor transport method, have ultraclean and ultraflat surfaces that make Cat-EAA-SH molecules aligned into a well-ordered network of a large-scale. Topographic study of the catechol-terminated molecules on Au NPLs using atomic force microscopy showed more orderly orientation and higher density, leading to significantly higher adhesion as observed from local force-distance curves than those on other Au surfaces. These coherently aligned catechol-terminated molecules on the atomically smooth gold surface led to significanty more reproducible and thus more physico-chemically meaningful measurements than was possible before by employing rough gold surfaces.

Production of quasi-2D graphene nanosheets through the solvent exfoliation of pitch-based carbon fiber.

Stable dispersion of quasi-2D graphene sheets with a concentration up to 1.27 mg mL(-1) was prepared by sonication-assisted solvent exfoliation of pitch-based carbon fiber in N-methyl pyrrolidone with the mass yield of 2.32%. Prepared quasi-2D graphene sheets have multi-layered 2D plate-like morphology with rich inclusions of graphitic carbons, a low number of structural defects, and high dispersion stability in aprotic polar solvents, and facilitate the utilization of quasi-2D graphene sheets prepared from pitch-based carbon fiber for various electronic and structural applications. Thin films of quasi-2D graphene sheets prepared by vacuum filtration of the dispersion of quasi-2D graphene sheets demonstrated electrical conductivity up to 1.14 × 10(4) Ω/□ even without thermal treatment, which shows that pitch-based carbon fiber might be useful as the source of graphene-related nanomaterials. Because pitch-based carbon fiber could be prepared from petroleum pitch, a very cheap structural material for the pavement of asphalt roads, our approach might be promising for the mass production of quasi-2D graphene nanomaterials.

Induction and control of supramolecular chirality by light in self-assembled helical nanostructures.

Evolution of supramolecular chirality from self-assembly of achiral compounds and control over its handedness is closely related to the evolution of life and development of supramolecular materials with desired handedness. Here we report a system where the entire process of induction, control and locking of supramolecular chirality can be manipulated by light. Combination of triphenylamine and diacetylene moieties in the molecular structure allows photoinduced self-assembly of the molecule into helical aggregates in a chlorinated solvent by visible light and covalent fixation of the aggregate via photopolymerization by ultraviolet light, respectively. By using visible circularly polarized light, the supramolecular chirality of the resulting aggregates is selectively and reversibly controlled by its rotational direction, and the desired supramolecular chirality can be arrested by irradiation with ultraviolet circularly polarized light. This methodology opens a route to ward the formation of supramolecular chiral conducting nanostructures from the self-assembly of achiral molecules.