An efficient eco-friendly adsorbent material based on waste copper slag-biomass ash geopolymer: dye sorption capacity and sustainable properties.

The primary intent of the research is to comprehensively assess the environmental benefits and cost dynamics associated with the adsorption process of CS-RHA (Copper Slag and Rice Husk Ash) to produce a novel geopolymer adsorbent material for application in wastewater treatment. The geopolymer forms a polyiron sialate network under alkali activation by dissolving fayalite, and aluminium silicate to ferro-ferri silicate hydrate gel. The mechanical strength, leaching characteristics, and microstructure of the geopolymer were determined using XRD and FTIR, and magnetic properties by VSM as well surface properties were derived from BET surface area and zeta potential. Recognizing the critical role of sodium iron silicate hydrate (NFS) in the sorption of methylene blue (MB) dyestuff, batch experiments were carried out using different adsorbents. The results indicated that the dye removal efficiency increased from 60% in control samples (FS) to 98% for the blend (FS1) under different pH values. The data was found to fit with the nonlinear form of Freundlich isotherm and follow pseudo-second-order kinetics. The active adsorption sites were deduced as -O-Fe-O-Si-O-Na and Si-OH groups. The addition of RHA increases the adsorption capacity of the geopolymer in a short time through chemical adsorption. The significant negative surface charge promotes MB adsorption via improved electrostatic attraction. The spent adsorbents were recovered through magnetic separation with a retrieval rate of 80-85% and active sites were rejuvenated by calcination. Consequently, waste copper slag emerges as a promising adsorbent with minimum potential ecological risk and high effective recycling capacity.

A study on the role of surface functional groups of metakaolin in the removal of methylene blue: Characterization, kinetics, modeling and RSM optimization.

In this study, thermally activated kaolinite clay is explored as a suitable material for dye removal applications, which gave rise to highly reactive silica species in a broad range of aluminosilicate clusters. Multinuclear NMR studies described it as a short-range network in which Al sites in IV, V, and VI are coordinated, and Si is present mainly as Si(Q4(1Al)). Critical parameters for methylene blue (MB) were determined by the Placket Burman Design (PBD) as initial dye concentration, contact time, adsorbent dosage, pH and size. The % of MB removal studied after optimizing the parameters by central composite design (CCD), based on Response Surface Methodology, was found to be 90%. The adsorption kinetics and thermodynamics were systematically studied and reported by fitting them into different models. The maximum removal of the dye reached 97.8 mg/g according to the Freundlich isotherm, accomplished through chemisorption, following a pseudo-second-order reaction and the process is thermodynamically spontaneous and endothermic. The line spectrum of X-ray photoelectron spectroscopy (XPS) shows the participation of Si, Al, O, Ca and Na of Metakaolin (AK) and nitrogen of MB in the adsorption process. The appropriate stabilization of the N atom of the chromophore on the Si and Al atom in AK resulting from the ionic interaction on the surface is established from an increase in the binding energy of Al and Si. A single bridging oxygen signal at 532.32eVcorresponding to AK after dye adsorption tends to form siloanol/aluminol, and their interaction is lowered to 531.58eV. Regeneration of adsorbent after thermal treatment without loss of efficiency proved.

Mono- and Bimetallic Nanoparticles for Catalytic Degradation of Hazardous Organic Dyes and Antibacterial Applications.

In the present work, gold (Au), silver (Ag), and copper (Cu) based mono- and bimetallic NPs are prepared using a cost-effective facile wet chemical route. The pH for the synthesis is optimized in accordance with the optical spectra and supported by the finite difference time domain simulation studies. FESEM and TEM micrographs are used to analyze the morphology of the prepared nanoparticles. TEM images of bimetallic nanoparticles (BMPs) verified their bimetallic nature. XRD studies confirmed the formation of fcc-structured mono- and bimetallic NPs. Photoluminescence studies of the as-synthesized NPs are in good agreement with the previous publications. These synthesized NPs showed enhanced catalytic activity for the reduction/degradation of 4-nitrophenol, rhodamine B, and indigo carmine dyes in the presence of sodium borohydride (NaBH4) compared to NaBH4 alone. For the reduction of 4-nitrophenol, Au, Cu, and CuAg nanoparticles exhibited good catalytic efficiency compared to others, whereas for the degradation of rhodamine B and indigo carmine dyes the catalytic efficiency is comparatively high for CuAg BMPs. Furthermore, the antibacterial assay is carried out, and Ag NPs display effective antibacterial activity against Klebsiella pneumoniae, Salmonella ser. Typhimurium, Acinetobacter baumannii, Shigella flexneri, and Pseudomonas aeruginosa.

Mylohyoid Ridge as a Predictor of Available Bone for Implant Placement: A Cone-Beam Computed Tomography (CBCT) Retrospective Observational Study.

INTRODUCTION: The posterior mandibular region, due to the presence of vital structures, poses a high risk during implant placement because of its susceptibility to neurovascular injury and perforation of the lingual cortex. A breach in implant length and available bone height may lead to serious intraoperative and postoperative complications. Prediction of the exact location of the inferior alveolar nerve and submandibular fossa anatomy is a prerequisite for ideal implant placement, which is always not possible with conventional radiographic and clinical techniques. MATERIALS AND METHODS: One hundred ten cone-beam computed tomographies (CBCTs) of patients were acquired from the radiological archives of a radiological center in Chennai. DICOM files from CBCT were exported to Bly Sky Plan software. Cross-sections of the second molar and first molar were extracted following the inclusion criteria. The linear dimension between the mandibular canal and mylohyoid ridge and anatomic variables of the submandibular fossa were measured digitally on the left and right sides using software measuring tools. Descriptive statistics were done. The unilateral and bilateral site and gender differences were evaluated. Bone height superior to the mandibular canal was correlated with the submandibular fossa parameters; depth of undercut in the vertical and horizontal directions; and angle of the undercut. RESULTS: The mandibular canal was on average 5.5 mm and 4 mm inferior to the Mylohyoid ridge in the second molar region and first molar region, respectively, with the right and left sides showing no statistically significant difference. The depth of fossa undercut in vertical and horizontal dimensions was higher in the second molar region compared to the first molar region. The height of the deepest point of the undercut in the vertical dimensions showed a positive correlation with the bone available between the mandibular canal and the mylohyoid ridge. CONCLUSION: Keeping 2 mm of safety factor in consideration, implants can be safely placed up to the mylohyoid ridge in 100% of cases and 2 mm below the mylohyoid ridge in 78.9% of cases in the mandibular second molar region. In keeping with a safety factor of 2 mm, implants can be safely placed up to the mylohyoid ridge in 82.6% of cases and 2 mm below the mylohyoid ridge in 43.1% of cases in the first molar region. A more pronounced undercut was seen in the second molar region than in the first molar region. Deeper fossa undercuts in vertical dimension are associated with more inferior positioning of the mandibular canal.

A small molecule targeting hepatitis B surface antigen inhibits clinically relevant drug-resistant hepatitis B virus.

BACKGROUND: Currently approved oral antivirals for chronic HBV infection target the reverse transcriptase (RT) domain of the HBV polymerase. Emergence of drug resistance has been reported in a small proportion of chronic HBV patients on prolonged treatment with antivirals. We recently reported ZINC20451377, a small molecule targeting hepatitis B surface antigen (HBsAg) that effectively inhibits both WT HBV and tenofovir-resistant HBV. Due to the partial overlap between the RT domain and HBsAg, drug-resistant mutants are associated with corresponding mutations in HBsAg. OBJECTIVES: To evaluate the efficacy of ZINC20451377 against nine clinically relevant drug-resistant HBV mutants that lead to simultaneous mutations in the overlapping HBsAg gene. METHODS: Huh7 cells were transfected with 1.2× HBV replicons corresponding to WT HBV or drug-resistant HBV mutants and treated with different concentrations of ZINC20451377. We assessed the IC50 values of ZINC20451377 for HBsAg levels in the culture supernatants using ELISAs. HBV secretion was measured by immunocapture of secreted virions followed by real-time PCR quantitation of virion-associated DNA. RESULTS: ZINC20451377 led to a dose-dependent inhibition of secreted HBsAg encoded by WT HBV and all nine drug-resistant mutants tested and the IC50 values were in the low micromolar range. ZINC20451377 inhibited HBV secretion from drug-resistant mutants except for mutants harbouring the rtL180M + rtM204V (MV) mutation. CONCLUSIONS: The small molecule ZINC20451377 inhibits HBsAg and virion secretion in some of the clinically relevant drug-resistant HBV mutants. ZINC20451377 has a modest overall effect, and it was not effective against the MV mutants (lamivudine- and entecavir-resistant mutants).

A novel piperazine derivative that targets hepatitis B surface antigen effectively inhibits tenofovir resistant hepatitis B virus.

Chronic hepatitis B virus (HBV) infection is a global problem. The loss of hepatitis B surface antigen (HBsAg) in serum is a therapeutic end point. Prolonged therapy with nucleoside/nucleotide analogues targeting the HBV-polymerase may lead to resistance and rarely results in the loss of HBsAg. Therefore, inhibitors targeting HBsAg may have potential therapeutic applications. Here, we used computational virtual screening, docking, and molecular dynamics simulations to identify potential small molecule inhibitors against HBsAg. After screening a million molecules from ZINC database, we identified small molecules with potential anti-HBV activity. Subsequently, cytotoxicity profiles and anti-HBV activities of these small molecules were tested using a widely used cell culture model for HBV. We identified a small molecule (ZINC20451377) which binds to HBsAg with high affinity, with a KD of 65.3 nM, as determined by Surface Plasmon Resonance spectroscopy. Notably, the small molecule inhibited HBsAg production and hepatitis B virion secretion (10 µM) at low micromolar concentrations and was also efficacious against a HBV quadruple mutant (CYEI mutant) resistant to tenofovir. We conclude that this small molecule exhibits strong anti-HBV properties and merits further testing.

Septal defect with polyvalvular involvement: A cardiac imaging hallmark of Trisomy 18.

Congenital Heart Diseases occur in close to 90% of children with Trisomy 18. A ventricular septal defect along with abnormalities of more than one cardiac valve is considered to be an imaging hallmark of Trisomy 18. We present echocardiographic images of an infant with Trisomy 18 who had a large ventricular septal defect and abnormalities of all cardiac valves.

Direct Micromolding of Bimetals and Transparent Conducting Oxide Using Metal-TOABr Complexes as Single-Source Precursors.

Patterning of metals, alloys, and conducting oxides is vitally important for many industrial applications pertaining to many technological devices. In this report, we have used the metal anion alkyl ammonium complex (M-TOABr) as a single-source precursor to obtain thin films as well as micro (µ)-patterns of bimetals (Au-Pd, Au-Pt, Au-Cu, and Pt-Pd) and conducting oxides (ITO). This complex can be easily filled inside the soft mold and converted to the desired material in a single step known as direct patterning. The as-obtained µ-pattern comprises a well-connected network of nanocrystals giving rise to metallic conductivity. These periodically aligned bimetals and transparent conducting oxide (TCO) microwires could effectively serve as electrodes as well as an electrocatalyst with the prudence of providing passage for light transmission for many functional photoelectrochemical devices. In addition, the electrochemical stability of the bimetallic film was examined by fabricating a supercapacitor device and by studying its performance.

"Castor Oil" - The Culprit of Acute Hair Felting.

Acute hair felting is a rare disorder of scalp hair. In this condition, the hair becomes twisted, entangled as a hard stony mass resembling a bird's nest. Sudden hair matting has been reported earlier in the literature after vigorous use of chemical and herbal shampoos. Plica polonica is a patchy area of hair matting occurring in due course of time in neglected hair or underlying psychiatric illness. This case is interesting as the whole scalp hair matted immediately after using coconut oil and castor oil following washing. Growing long hair and taking oil bath are cultural and religious customs in South India. The high viscosity of castor oil and long hair had contributed to sudden felting of hair. This disorder of hair is irreversible and the hair should be cut off. Acute nature of this disorder will result in a serious psychological impact on the patient and the family.

Transparent and Flexible Supercapacitors with Networked Electrodes.

Transparent and flexible energy storage devices have received immense attention due to their suitability for innovative electronics and displays. However, it remains a great challenge to fabricate devices with high storage capacity and high degree of transmittance. This study describes a simple process for fabrication of supercapacitors with ≈75% of visible transparency and areal capacitance of ≈3 mF cm-2 with high stability tested over 5000 cycles of charging and discharging. The electrodes consist of Au wire networks obtained by a simple crackle template method which are coated with MnO2 nanostructures by electrodeposition process. Importantly, the membrane separator itself is employed as substrate to bring in the desired transparency and light weight while additionally exploiting its porous nature in enhancing the interaction of electrolyte with the active material from both sides of the substrate, thereby enhancing the storage capacity. The method opens up new ways for fabricating transparent devices.

Visibly Transparent Heaters.

Heater plates or sheets that are visibly transparent have many interesting applications in optoelectronic devices such as displays, as well as in defrosting, defogging, gas sensing and point-of-care disposable devices. In recent years, there have been many advances in this area with the advent of next generation transparent conducting electrodes (TCE) based on a wide range of materials such as oxide nanoparticles, CNTs, graphene, metal nanowires, metal meshes and their hybrids. The challenge has been to obtain uniform and stable temperature distribution over large areas, fast heating and cooling rates at low enough input power yet not sacrificing the visible transmittance. This review provides topical coverage of this important research field paying due attention to all the issues mentioned above.

Immobilized lipase catalyzing glucose stearate synthesis and their surfactant properties analysis.

Sugar fatty acid esters are practical importance and have a variety of applications that include surfactants and as an emulsifying agent. In this study, we report glucose stearate synthesis using lipase-Fe3O4 nanoparticles catalyst. The influence of various reaction factors, such as silica gel concentration, molar ratio of sugar/acid, reaction temperature and speed of agitation on esterification by immobilized enzyme was analyzed. The glucose stearate esterification degree of 87.2 % was obtained under the optimized condition: 1:2 molar ratio of glucose/stearic acid, 2 % (w/v) of silica gel at 120 rpm and 40 °C. Glucose esters were characterized according to their surfactant activity like emulsification index, oil displacement activity and antimicrobial activity. The results indicated glucose stearate acts as biosurfactant, with emulsification index of 66 % in mustard oil and oil displacement activity of 19.64 cm2.

Fabrication of Oxidation-Resistant Metal Wire Network-Based Transparent Electrodes by a Spray-Roll Coating Process.

Roll and spray coating methods have been employed for the fabrication of highly oxidation resistant transparent and conducting electrodes (TCEs) by a simple solution process using crackle lithography technique. We have spray-coated a crackle paint-based precursor to produce highly interconnected crackle network on PET roll mounted on a roll coater with web speed of 0.6 m/min. Ag TCE with a transmittance of 78% and sheet resistance of ∼20 Ω/□ was derived by spraying Ag precursor ink over the crackle template followed by lift-off and annealing under ambient conditions. The Ag wire mesh was stable toward bending and sonication tests but prone to oxidation in air. When electrolessly coated with Pd, its robustness toward harsh oxidation conditions was enhanced. A low-cost transparent electrode has also been realized by using only small amounts of Ag as seed layer and growing Cu wire mesh by electroless method. Thus, made Ag/Cu meshes are found to be highly stable for more than a year even under ambient atmosphere.

Spray coating of crack templates for the fabrication of transparent conductors and heaters on flat and curved surfaces.

Transparent conducting electrodes (TCEs) have been made on flat, flexible, and curved surfaces, following a crack template method in which a desired surface was uniformly spray-coated with a crackle precursor (CP) and metal (Ag) was deposited by vacuum evaporation. An acrylic resin (CP1) and a SiO2 nanoparticle-based dispersion (CP2) derived from commercial products served as CPs to produce U-shaped cracks in highly interconnected networks. The crack width and the density could be controlled by varying the spray conditions, resulting in varying template thicknesses. By depositing Ag in the crack regions of the templates, we have successfully produced Ag wire network TCEs on flat-flexible PET sheets, cylindrical glass tube, flask and lens surface with transmittance up to 86%, sheet resistance below 11 Ω/□ for electrothermal application. When used as a transparent heater by joule heating of the Ag network, AgCP1 and AgCP2 on PET showed high thermal resistance values of 515 and 409 °C cm(2)/W, respectively, with fast response (<20 s), requiring only low voltages (<5 V) to achieve uniform temperatures of ∼100 °C across large areas. Similar was the performance of the transparent heater on curved glass surfaces. Spray coating in the context of crack template is a powerful method for producing transparent heaters, which is shown for the first time in this work. AgCP1 with an invisible wire network is suited for use in proximity while AgCP2 wire network is ideal for use in large area displays viewed from a distance. Both exhibited excellent defrosting performance, even at cryogenic temperatures.

Metal anion-alkyl ammonium complexes as direct write precursors to produce nanopatterns of metals, nitrides, oxides, sulfides, and alloys.

The study explores the possibility of using metal anions complexed with tetraoctylammonium bromide (ToABr) as single-source direct write precursors in e-beam and soft lithography processes to obtain micro- and nanoscale patterns of various metals, i.e., Au, Pd, Pt, Ag, Pb and Cu, as well as of their alloys (AuCu), oxides (Co(3)O(4), ZnO), nitrides (CoN, InN, GaN), and sulfides (Ag(2)S). The extraction efficiency of ToABr for different metal anions is found to be varied (40-90%), but the obtained precursors are easily processable as they have reasonable solubility in common solvents and are obtainable as smooth films, both being important for high-resolution patterning. The e-resist action of the precursors originates from the extreme e-beam sensitivity of the hydrocarbon chain present in ToABr, while direct micromolding has been possible due to easy flow of the precursor solutions in capillaries. The interaction of the anion and ToABr being mainly electrostatic enables easy removal of the hydrocarbon from patterned regions by thermolysis on a hot plate in the ambient or in controlled atmosphere to form the desired product. This method can be easily generalized.