Disc degeneration: current surgical options.

Chronic low back pain attributed to lumbar disc degeneration poses a serious challenge to physicians. Surgery may be indicated in selected cases following failure of appropriate conservative treatment. For decades, the only surgical option has been spinal fusion, but its results have been inconsistent. Some prospective trials show superiority over usual conservative measures while others fail to demonstrate its advantages. In an effort to improve results of fusion and to decrease the incidence of adjacent segment degeneration, total disc replacement techniques have been introduced and studied extensively. Short-term results have shown superiority over some fusion techniques. Mid-term results however tend to show that this approach yields results equivalent to those of spinal fusion. Nucleus replacement has gained some popularity initially, but evidence on its efficacy is scarce. Dynamic stabilisation, a technique involving less rigid implants than in spinal fusion and performed without the need for bone grafting, represents another surgical option. Evidence again is lacking on its superiority over other surgical strategies and conservative measures. Insertion of interspinous devices posteriorly, aiming at redistributing loads and relieving pain, has been used as an adjunct to disc removal surgery for disc herniation. To date however, there is no clear evidence on their efficacy. Minimally invasive intradiscal thermocoagulation techniques have also been tried, but evidence of their effectiveness is questioned. Surgery using novel biological solutions may be the future of discogenic pain treatment. Collaboration between clinicians and basic scientists in this multidisciplinary field will undoubtedly shape the future of treating symptomatic disc degeneration.

FiberWire is superior in strength to stainless steel wire for tension band fixation of transverse patellar fractures.

BACKGROUND: The metal implants used to achieve fixation of displaced transverse patellar fractures are associated with implant failure, postoperative pain and a significant re-operation rate. Recent studies have examined braided suture as a possible alternative to stainless steel wire to increase patient satisfaction and decrease re-operation rates, but suture has not demonstrated clearly superior fixation strength. FiberWire is a reinforced braided polyblend suture that has demonstrated superior characteristics to the previous sutures studied and has not to our knowledge been examined as a material for tension band fixation of transverse patellar fractures. METHODS: Materials testing was performed on repeated samples of No. 5 FiberWire suture and 18-gauge stainless steel wire. The strength and stiffness of each material was measured. The two materials were then used for tension band fixation on a novel transverse patellar fracture model and tested to failure by three-point bending. The constructs included a single stainless steel wire, a single-strand FiberWire tied with a sliding knot, double-strand FiberWire tied with sliding knots and double-strand FiberWire tied with a Wagoner's Hitch. The fixation strength and stiffness of the constructs were measured. FINDINGS: Unlike stainless steel, FiberWire maintained its initial stiffness until failure. Furthermore, during three-point-bend testing, double-strand FiberWire was found to have a significantly higher failure load than stainless steel wire when the suture was tied and locked under the tension produced by a modified Wagoner's Hitch. INTERPRETATION: FiberWire is a potentially superior alternative to stainless steel wire in tension band fixation of transverse patellar fractures.

An intramedullary alignment guide lodging within the femoral canal during total knee arthroplasty: a case report.

The usual complications of total knee arthroplasty include thrombo-embolism, infection, and loosening. We report an unusual and potentially serious complication of an intramedullary guide lodging within the femoral canal during the procedure. Considering the risk of fracture and additional exposure, the guide was not removed and was cut in situ. The rest of the operation was completed successfully and the patient made an uneventfully recovery.

Incidence and management of pulmonary embolism following spinal surgery occurring while under chemical thromboprophylaxis.

Patients undergoing spinal surgery are at risk of developing thromboembolic complications even though lower incidences have been reported as compared to joint arthroplasty surgery. Deep vein thrombosis (DVT) has been studied extensively in the context of spinal surgery but symptomatic pulmonary embolism (PE) has engaged less attention. We prospectively followed a consecutive cohort of 270 patients undergoing spinal surgery at a single institution. From these patients, only 26 were simple discectomies, while the largest proportion (226) was fusions. All patients received both low molecular weight heparin (LMWH) initiated after surgery and compressive stockings. PE was diagnosed with spiral chest CT. Six patients developed symptomatic PE, five during their hospital stay. In three of the six patients the embolic event occurred during the first 3 postoperative days. They were managed by the temporary insertion of an inferior vena cava (IVC) filter thus allowing for a delay in full-dose anticoagulation until removal of the filter. None of the PE patients suffered any bleeding complication as a result of the introduction of full anticoagulation. Two patients suffered postoperative haematomas, without development of neurological symptoms or signs, requiring emergency evacuation. The overall incidence of PE was 2.2% rising to 2.5% after exclusion of microdiscectomy cases. The incidence of PE was highest in anterior or combined thoracolumbar/lumbar procedures (4.2%). There is a large variation in the reported incidence of PE in the spinal literature. Results from the only study found in the literature specifically monitoring PE suggest an incidence of PE as high as 2.5%. Our study shows a similar incidence despite the use of LMWH. In the absence of randomized controlled trials (RCT) it is uncertain if this type of prophylaxis lowers the incidence of PE. However, other studies show that the morbidity of LMWH is very low. Since PE can be a life-threatening complication, LMWH may be a worthwhile option to consider for prophylaxis. RCTs are necessary in assessing the efficacy of DVT and PE prophylaxis in spinal patients.

Damage-based finite-element vertebroplasty simulations.

The objectives of this study were to quantify the efficacy of vertebroplasty according to: (1) damage and (2) cement quantity (fill) and modulus. Vertebral body damage was numerically simulated using a previously validated two-dimensional finite-element model coupled with an elasto-plastic modulus reduction (EPMR) scheme. The effects of cement fill (% marrow replaced by cement, % MRC) and cement modulus on vertebral apparent modulus and trabecular bone tissue stress concentrations were parametrically assessed for four EPMR damage models (19%, 33%, 60%, and 91% modulus reduction). For this analysis, the elastic modulus of the trabecular bone tissue and marrow elements were assumed to be 10 GPa and 10 kPa, respectively. The effect of cement modulus (varied in the range 1 GPa to 9 GPa) on vertebral apparent modulus was also examined for partial fill (39% MRC) and complete fill (100% MRC) using the 33% modulus reduction damage model. In the case of polymethylmethacrylate (PMMA cement modulus = 2.16 GPa), restoration of the thoracic vertebral body (T10) apparent modulus to undamaged levels required 71% and 100% cement fill for the 19-33% and 60-91% modulus reduction damage models, respectively. Variations in cement modulus had no appreciable effect on the recovery of vertebral apparent modulus to undamaged levels for simulations of partial cement fill (39% MRC). For complete cement fill, however, a PMMA cement modulus produced approximately a 2-fold increase (82%) in vertebral apparent modulus relative to the undamaged vertebral body. Increasing the cement modulus to 9 GPa increased the vertebral apparent modulus over 2.5-fold (158%) relative to the undamaged state. The EPMR damage scheme and repair simulations performed in this study will help clinicians and cement manufacturers to improve vertebroplasty procedures.