A comparative study based on performance and techno-economic analysis of different strategies for PV-Electrolyzer (green) hydrogen fueling incinerator system.

The integration of hydrogen in the primary energy mix requires a major technological shift in virtually every energy-related application. This study has attempted to investigate the techno-economic solar photovoltaic (PV) integrated water electrolysis and waste incineration system. Three different strategies, i.e., (i) PV + Battery(Hybrid mode with required batteries); (ii) auto-ignition (Direct coupling); and (iii) PV + Secondary-Electrolyzer(Direct coupling assisted with secondary electrolyzer), have been envisioned. The 'PV + Battery' consume 42.42 % and 15.07 % less energy than the auto-ignition and 'PV + Secondary-Electrolyzer' methods. However, the capital cost of 'PV + Battery' has been calculated to be 15.4 % and 11.8 % more than auto-ignition and 'PV + Secondary-Electrolyzer, respectively.The energy consumption relative to waste input, the 'PV + Battery' method used 80 % less energy, while auto-ignition and 'PV + Secondary-Electrolyzer' showed 70.5 % and 77.5 % less energy, respectively. Furthermore, these approaches showed a vast difference in cost-benefit for the longer run. 'PV + Battery' was forecasted to be 73.3 % and 23.3 % more expensive than auto-ignition and 'PV + Secondary-Electrolyzer' methods, respectively, for 30 years. Overall, this study can benefit from using either of these methods depending on the application, usage scale, and climatic conditions.

Biomimetically Inspired Highly Homogeneous Hydrophilization of Graphene with Poly(l-DOPA): Toward Electroconductive Coatings from Water-Processable Paints.

Water-based processing of graphene-typically considered as physicochemically incompatible with water in the macroscale-emerges as the key challenge among the central postulates of green nanotechnology. These problematic concerns are derived from the complex nature of graphene in the family of sp2-carbon nanoallotropes. Indeed, nanomaterials hidden under the common "graphene" signboard are very rich in morphological and physicochemical variants. In this work, inspired by the adhesion chemistry of mussel biomaterials, we have synthesized novel, water-processable graphene-polylevodopa (PDOPA) hybrids. Graphene and PDOPA were covalently amalgamated via the "growth-from" polymerization of l-DOPA (l-3,4-dihydroxyphenylalanine) monomer in air, yielding homogeneously PDOPA-coated (23 wt %) (of thickness 10-20 nm) hydrophilic flakes. The hybrids formed >1 year stable and water-processable aqueous dispersions and further conveniently processable paints of viscosity 0.4 Pa·s at 20 s-1 and a low yield stress τ0 up to 0.12 Pa, hence exhibiting long shelf-life stability and lacking sagging after application. Demonstrating their applicability, we have found them as surfactant-like nanoparticles stabilizing the larger, pristine graphene agglomerates in water in the optimized graphene/graphene-PDOPA weight ratio of 9:1. These characteristics enabled the manufacture of conveniently paintable coatings of low surface resistivity of 1.9 kΩ sq-1 (0.21 Ω·m) which, in turn, emerge as potentially applicable in textronics, radar-absorbing materials, or electromagnetic interference shielding.

The True Amphipathic Nature of Graphene Flakes: A Versatile 2D Stabilizer.

The fundamental colloidal properties of pristine graphene flakes remain incompletely understood, with conflicting reports about their chemical character, hindering potential applications that could exploit the extraordinary electronic, thermal, and mechanical properties of graphene. Here, the true amphipathic nature of pristine graphene flakes is demonstrated through wet-chemistry testing, optical microscopy, electron microscopy, and density functional theory, molecular dynamics, and Monte Carlo calculations, and it is shown how this fact paves the way for the formation of ultrastable water/oil emulsions. In contrast to commonly used graphene oxide flakes, pristine graphene flakes possess well-defined hydrophobic and hydrophilic regions: the basal plane and edges, respectively, the interplay of which allows small flakes to be utilized as stabilizers with an amphipathic strength that depends on the edge-to-surface ratio. The interactions between flakes can be also controlled by varying the oil-to-water ratio. In addition, it is predicted that graphene flakes can be efficiently used as a new-generation stabilizer that is active under high pressure, high temperature, and in saline solutions, greatly enhancing the efficiency and functionality of applications based on this material.

The Effect of the Gaseous Environment on the Electrical Conductivity of Multi-Walled Carbon Nanotube Films over a Wide Temperature Range.

The surrounding gas atmosphere can have a significant influence on the electrical properties of multi-walled carbon nanotube (CNT) ensembles. In this study, we subjected CNT films to various gaseous environments or vacuum to observe how such factors alter the electrical resistance of networks at high temperatures. We showed that the removal of adsorbed water and other contaminants from the surface under reduced pressure significantly affects the electrical conductivity of the material. We also demonstrated that exposing the CNT films to the hydrogen atmosphere (as compared to a selection of gases of inert and oxidizing character) at elevated temperatures results in a notable reduction of electrical resistance. We believe that the observed sensitivity of the electrical properties of the CNT films to hydrogen or vacuum at elevated temperatures could be of practical importance.

Highly Conductive Doped Hybrid Carbon Nanotube-Graphene Wires.

The following paper explores the nature of electronic transport in a hybrid carbon nanotube-graphene conductive network. These networks may have a tremendous impact on the future formation of new electrical conductors, batteries, and supercapacitors, as well as many other electronic and electrical applications. The experiments described show that the deposition of graphene nanoflakes within a carbon nanotube network improves both its electrical conductivity and its current-carrying capacity. They also show that the effectiveness of doping is enhanced. To explain the effects observed in the hybrid carbon nanotube-graphene conductive network, a theoretical model was developed. The theory explains that graphenes are not merely effective conductive fillers of the carbon nanotube networks but also effective bridges that are able to introduce additional states at the Fermi level of carbon nanotubes.

Carbon nanotube functionalization as a route to enhancing the electrical and mechanical properties of Cu-CNT composites.

Copper-CNT (carbon nanotube) composite materials are promising alternatives to conventional conductors in applications ranging from interconnects in microelectronics to electrical cabling in aircraft and vehicles. Unfortunately, exploiting the full potential of these composites is difficult due to the poor Cu-CNT electro-mechanical interface. We demonstrate through large-scale ab initio calculations and sonication experiments that this problem can be addressed by CNT surface modification. Our calculations show that covalent functionalization of CNTs below 6.7 at% significantly improves Cu-CNT wetting and the mechanical properties of the composite. Oxidative pre-treatment of CNTs enhances the Young's modulus of the composite by nearly a factor 3 above that of pure Cu, whereas amination slightly improves the electrical current density with respect to the unmodified Cu-CNT system in the high bias regime. However, only nitrogen doping can effectively improve both the mechanical and electrical properties of the composite. As the experiments show, consistent with the calculations, substitutional doping with nitrogen effectively improves adhesion of the CNT to the Cu matrix. We also predict an improvement in the mechanical properties for the composite containing doped double-wall CNTs. Moreover, the calculations indicate that the presence of nitrogen dopants almost doubles locally the transmission through the nanotube and reduces the back scattering in the Cu matrix around the CNT. The computed electrical conductance of N-doped Cu-CNT "carpets" exceeds that of an undoped system by ∼160%.

Advancing the Use of High-Performance Graphene-Based Multimodal Polymer Nanocomposite at Scale.

The production of an innovative, high-performance graphene-based polymer nanocomposite using cost-effective techniques was pursued in this study. Well-dispersed and uniformly distributed graphene platelets within a polymer matrix, with strong interfacial bonding between the platelets and the matrix, provided an optimal nanocomposite system for industrial interest. This study reports on the reinforcement of high molecular weight multimodal-high-density polyethylene reinforced by a microwave-induced plasma graphene, using melt intercalation. The tailored process included designing a suitable screw configuration, paired with coordinating extruder conditions and blending techniques. This enabled the polymer to sufficiently degrade, predominantly through thermomechanical-degradation, as well as thermo-oxidative degradation, which subsequently created a suitable medium for the graphene sheets to disperse readily and distribute evenly within the polymer matrix. Different microscopy techniques were employed to prove the effectiveness. This was then qualitatively assessed by Raman spectroscopy, X-ray diffraction, rheology, mechanical testing, density measurements, thermal expansion, and thermogravimetric analysis, confirming both the originality as well as the effectiveness of the process.

Photonic Sorting of Aligned, Crystalline Carbon Nanotube Textiles.

Floating catalyst chemical vapor deposition uniquely generates aligned carbon nanotube (CNT) textiles with individual CNT lengths magnitudes longer than competing processes, though hindered by impurities and intrinsic/extrinsic defects. We present a photonic-based post-process, particularly suited for these textiles, that selectively removes defective CNTs and other carbons not forming a threshold thermal pathway. In this method, a large diameter laser beam rasters across the surface of a partly aligned CNT textile in air, suspended from its ends. This results in brilliant, localized oxidation, where remaining material is an optically transparent film comprised of few-walled CNTs with profound and unique improvement in microstructure alignment and crystallinity. Raman spectroscopy shows substantial D peak suppression while preserving radial breathing modes. This increases the undoped, specific electrical conductivity at least an order of magnitude to beyond that of single-crystal graphite. Cryogenic conductivity measurements indicate intrinsic transport enhancement, opposed to simply removing nonconductive carbons/residual catalyst.

Extreme Magneto-transport of Bulk Carbon Nanotubes in Sorted Electronic Concentrations and Aligned High Performance Fiber.

We explored high-field (60 T) magneto-resistance (MR) with two carbon nanotube (CNT) material classes: (1) unaligned single-wall CNTs (SWCNT) films with controlled metallic SWCNT concentrations and doping degree and (2) CNT fiber with aligned, long-length microstructure. All unaligned SWCNT films showed localized hopping transport where high-field MR saturation definitively supports spin polarization instead of a more prevalent wave function shrinking mechanism. Nitric acid exposure induced an insulator to metal transition and reduced the positive MR component. Aligned CNT fiber, already on the metal side of the insulator to metal transition, had positive MR without saturation and was assigned to classical MR involving electronic mobility. Subtracting high-field fits from the aligned fiber's MR yielded an unconfounded negative MR, which was assigned to weak localization. It is concluded that fluctuation induced tunnelling, an extrinsic transport model accounting for most of the aligned fiber's room temperature resistance, appears to lack MR field dependence.

Breaking the electrical barrier between copper and carbon nanotubes.

Improving the interface between copper and carbon nanotubes (CNTs) offers a straightforward strategy for the effective manufacturing and utilisation of Cu-CNT composite material that could be used in various industries including microelectronics, aerospace and transportation. Motivated by a combination of structural and electrical measurements on Cu-M-CNT bimetal systems (M = Ni, Cr) we show, using first principles calculations, that the conductance of this composite can exceed that of a pure Cu-CNT system and that the current density can even reach 1011 A cm-2. The results show that the proper choice of alloying element (M) and type of contact facilitate the fabrication of ultra-conductive Cu-M-CNT systems by creating a favourable interface geometry, increasing the interface electronic density of states and reducing the contact resistance. In particular, a small concentration of Ni between the Cu matrix and the CNT using either an "end contact" and or a "dot contact" can significantly improve the electrical performance of the composite. Furthermore the predicted conductance of Ni-doped Cu-CNT "carpets" exceeds that of an undoped system by ∼200%. Cr is shown to improve CNT integration and composite conductance over a wide temperature range while Al, at low voltages, can enhance the conductance beyond that of Cr.

Improving the electrical properties of carbon nanotubes with interhalogen compounds.

The electronic properties of carbon nanostructures such as carbon nanotubes (CNTs) or graphene can easily be tuned by the action of various doping agents. We present an experimental study and numerical analysis of how and why metallic and semiconductive CNTs can be p-doped by exposing them to two interhalogens: iodine monochloride and iodine monobromide. Simple application of these compounds was found to reduce the electrical resistance by as much as 2/3 without causing any unfavorable chemical modification, which could disrupt the highly conductive network of sp2 carbon atoms. To gain better insight into the underlying mechanism of the observed experimental results, we provide a first principles indication of how interhalogens interact with model metallic (5,5) and semiconductive (10,0) CNTs.

Carbon nanotube fibers and films: synthesis, applications and perspectives of the direct-spinning method.

The direct-spinning method of creation of CNT macroassemblies has received a lot of attention because of its simplicity to produce high-performance material without apparent limits to its size. CNT fibers or films have shown unparalleled properties and opened new areas of research and commercial development. The process designed more than a decade ago has already given interesting information about the basic science of nanomaterials, which in parallel led to the creation of the first prototypes with high potential of implementation in everyday life. Because of this, there has been growing interest in this technique with research articles coming into view from all around the world on a frequent basis. This review aims to summarize all the progress made in the direct-spinning process on a spectrum of fronts ranging from the study of complex synthesis parameters, material properties to its viable applications. The strong and weak points of the "Cambridge process" are carefully evaluated to put forward what challenges are most pressing. The future overlook puts the state of the art into perspective and suggests the prospective research directions.

Chitin and carbon nanotube composites as biocompatible scaffolds for neuron growth.

The design of biocompatible implants for neuron repair/regeneration ideally requires high cell adhesion as well as good electrical conductivity. Here, we have shown that plasma-treated chitin carbon nanotube composite scaffolds show very good neuron adhesion as well as support of synaptic function of neurons. The addition of carbon nanotubes to a chitin biopolymer improved the electrical conductivity and the assisted oxygen plasma treatment introduced more oxygen species onto the chitin nanotube scaffold surface. Neuron viability experiments showed excellent neuron attachment onto plasma-treated chitin nanotube composite scaffolds. The support of synaptic function was evident on chitin/nanotube composites, as confirmed by PSD-95 staining. The biocompatible and electrically-conducting chitin nanotube composite scaffold prepared in this study can be used for in vitro tissue engineering of neurons and, potentially, as an implantable electrode for stimulation and repair of neurons.

Soldering of Carbon Materials Using Transition Metal Rich Alloys.

Joining of carbon materials via soldering has not been possible up to now due to lack of wetting of carbons by metals at standard soldering temperatures. This issue has been a severely restricting factor for many potential electrical/electronic and mechanical applications of nanostructured and conventional carbon materials. Here we demonstrate the formation of alloys that enable soldering of these structures. By addition of several percent (2.5-5%) of transition metal such as chromium or nickel to a standard lead-free soldering tin based alloy we obtained a solder that can be applied using a commercial soldering iron at typical soldering temperatures of approximately 350 °C and at ambient conditions. The use of this solder enables the formation of mechanically strong and electrically conductive joints between carbon materials and, when supported by a simple two-step technique, can successfully bond carbon structures to any metal terminal. It has been shown using optical and scanning electron microscope images as well as X-ray diffraction patterns and energy dispersive X-ray mapping that the successful formation of carbon-solder bonds is possible, first, thanks to the uniform nonreactive dispersion of transition metals in the tin-based matrix. Further, during the soldering process, these free elements diffuse into the carbon-alloy border with no formation of brazing-like carbides, which would damage the surface of the carbon materials.

Amalgamation of complex iron(III) ions and iron nanoclusters with MWCNTs as a route to potential T2 MRI contrast agents.

Iron-filled multiwall carbon nanotubes (Fe@MWCNTs) were functionalized toward a variety of potential magnetic resonance imaging contrast agents. Oxidized Fe@MWNCTs were covered with PEG5000 via direct esterification or using acyl chloride derivatives. Alternatively, the latter were functionalized with an aminophenol ligand (Fe@O-MWCNT-L). Moreover, pristine Fe@MWCNTs were functionalized with N-phenylaziridine groups (Fe@f-MWCNT) via [2+1] cycloaddition of nitrene. All of these chemically modified nanotubes served as a vehicle for anchoring Fe(3+) ions. The new hybrids--Fe(III)/Fe@(f-/O-)MWCNTs--containing 6%-14% of the "tethered" Fe(3+) ions were studied in terms of the acceleration of relaxation of water protons in nuclear magnetic resonance. The highest transverse relaxivity r2=63.9±0.9 mL mg(-1) s(-1) was recorded for Fe(III)/Fe@O-MWCNT-L, while for Fe(III)/Fe@f-MWCNT, with r2=57.9±2.9 mL mg(-1) s(-1), the highest impact of the anchored Fe(III) ions was observed. The T1/T2 ratio of 30-100 found for all of the nanotube hybrids presented in this work is a very important factor for their potential application as T2 contrast agents. Increased stability of the hybrids was confirmed by ultraviolet-visible spectrophotometry.

Piezoresistive effect in carbon nanotube fibers.

The complex structure of the macroscopic assemblies of carbon nanotubes and variable intrinsic piezoresistivity of nanotubes themselves lead to highly interesting piezoresistive performance of this new type of conductive material. Here, we present an in-depth study of the piezoresistive effect in carbon nanotube fibers, i.e., yarnlike assemblies made purely of aligned carbon nanotubes, which are expected to find applications as electrical and electronic materials. The resistivity changes of carbon nanotube fibers were measured on initial loading, through the elastic/plastic transition, on cyclic loading and on stress relaxation. The various regimes of stress/strain behavior were modeled using a standard linear solid model, which was modified with an additional element in series to account for the observed creep behavior. On the basis of the experimental and modeling results, the origin of piezoresistivity is discussed. An additional effect on the resistivity was found as the fiber was held under load which led to observations of the effect of humidity and the associated water adsorption level on the resistivity. We show that the equilibrium uptake of moisture leads to the decrease in gauge factor of the fiber decrease, i.e., the reduction in the sensitivity of fiber resistivity to loading.

En route to controlled catalytic CVD synthesis of densely packed and vertically aligned nitrogen-doped carbon nanotube arrays.

The catalytic chemical vapour deposition (c-CVD) technique was applied in the synthesis of vertically aligned arrays of nitrogen-doped carbon nanotubes (N-CNTs). A mixture of toluene (main carbon source), pyrazine (1,4-diazine, nitrogen source) and ferrocene (catalyst precursor) was used as the injection feedstock. To optimize conditions for growing the most dense and aligned N-CNT arrays, we investigated the influence of key parameters, i.e., growth temperature (660, 760 and 860 °C), composition of the feedstock and time of growth, on morphology and properties of N-CNTs. The presence of nitrogen species in the hot zone of the quartz reactor decreased the growth rate of N-CNTs down to about one twentieth compared to the growth rate of multi-wall CNTs (MWCNTs). As revealed by electron microscopy studies (SEM, TEM), the individual N-CNTs (half as thick as MWCNTs) grown under the optimal conditions were characterized by a superior straightness of the outer walls, which translated into a high alignment of dense nanotube arrays, i.e., 5 × 10(8) nanotubes per mm(2) (100 times more than for MWCNTs grown in the absence of nitrogen precursor). In turn, the internal crystallographic order of the N-CNTs was found to be of a 'bamboo'-like or 'membrane'-like (multi-compartmental structure) morphology. The nitrogen content in the nanotube products, which ranged from 0.0 to 3.0 wt %, was controlled through the concentration of pyrazine in the feedstock. Moreover, as revealed by Raman/FT-IR spectroscopy, the incorporation of nitrogen atoms into the nanotube walls was found to be proportional to the number of deviations from the sp(2)-hybridisation of graphene C-atoms. As studied by XRD, the temperature and the [pyrazine]/[ferrocene] ratio in the feedstock affected the composition of the catalyst particles, and hence changed the growth mechanism of individual N-CNTs into a 'mixed base-and-tip' (primarily of the base-type) type as compared to the purely 'base'-type for undoped MWCNTs.

Ultra-pure single wall carbon nanotube fibres continuously spun without promoter.

We report a new strategy towards the control of carbon nanotube (CNT) structure and continuous fibre formation using a floating catalyst direct spinning CVD process. In the procedures used to date, a sulphur promoter precursor is added to significantly enhance the rate of CNT formation in the floating catalyst synthesis. Within the reaction zone, the rapidly grown nanotubes self-assemble into bundles, followed by their continuous spinning into fibres, yarns, films or tapes. In this paper we demonstrate a catalyst control strategy in the floating catalyst system, where the CNT formation process is independent of the presence of a promoter but leads to successful spinning of the macroscopic carbon nanotube assemblies with specific morphology, high purity (Raman D/G 0.03) and very narrow diameter range (0.8-2.5 nm). This can be achieved by the control of catalyst precursor decomposition and subsequent formation of homogeneous nano-sized catalyst particles.

Microwave conductivity of sorted CNT assemblies.

Recent progress with tailored growth and post-process sorting enables carbon nanotube (CNT) assemblies with predominantly metallic or semi-conducting concentrations. Cryogenic and microwave measurements performed here show transport dimensionality and overall order increasing with increasing metallic concentration, even in atmospheric doping conditions. By 120 GHz, the conductivity of predominantly semi-conducting assemblies grew to 400% its DC value at an increasing growth rate, while other concentrations a growth rate that tapered off. A generalized Drude model fits to the different frequency dependent behaviors and yields useful quality control parameters such as plasma frequency, mean free path, and degree of localization. As one of the first demonstrations of waveguides fabricated from this material, sorted CNTs from both as-made and post-process sources were inserted into sections of practical micro-strip. With both sources, sorted CNT micro-strip increasingly outperformed the unsorted with increasing frequency-- illustrating that sorted CNT assemblies will be important for high frequency applications.

Lipid nanoscaffolds in carbon nanotube arrays.

We present the fabrication of lipid nanoscaffolds inside carbon nanotube arrays by employing the nanostructural self-assembly of lipid molecules. The nanoscaffolds are finely tunable into model biomembrane-like architectures (planar), soft nanochannels (cylindrical) or 3-dimensionally ordered continuous bilayer structures (cubic). Carbon nanotube arrays hosting the above nanoscaffolds are formed by packing of highly oriented multiwalled carbon nanotubes which facilitate the alignment of lipid nanostructures without requiring an external force. Furthermore, the lipid nanoscaffolds can be created under both dry and hydrated conditions. We show their direct application in reconstitution of egg proteins. Such nanoscaffolds find enormous potential in bio- and nano-technological fields.