RESUMO
Flexible and stretchable electronics require both sensing elements and stretching-insensitive electrical connections. Conductive polymer composites and liquid metals are highly deformable but change their conductivity upon elongation and/or contain rare metals. Solid conductive composites are limited in mechanoelectrical properties and are often combined with macroscopic Kirigami structures, but their use is limited by geometrical restraints. Here, we introduce "Electrofluids", concentrated conductive particle suspensions with transient particle contacts that flow under shear that bridge the gap between classic solid composites and liquid metals. We show how Carbon Black (CB) forms large agglomerates when using incompatible solvents that reduce the electrical percolation threshold by 1 order of magnitude compared to more compatible solvents, where CB is well-dispersed. We analyze the correlation between stiffness and electrical conductivity to create a figure of merit of first electrofluids. Sealed elastomeric tubes containing different types of electrofluids were characterized under uniaxial tensile strain, and their electrical resistance was monitored. We found a dependency of the piezoresistivity with the solvent compatibility. Electrofluids enable the rational design of sustainable soft electronics components by simple solvent choice and can be used both as sensor and electrode materials, as we demonstrate.
RESUMO
Hybrid core-shell nanoparticles with metal cores and conductive polymer shells yield materials that are sinter-free and highly conductive but mechanically weak. Conventional composites of such nanoparticles are electrically insulating. Here, we introduce microscale phase-separated nanocomposites of hybrid gold-PEDOT:PPS particles in insulating poly(vinyl alcohol) (PVA). They combine electrical conductivities of up to 2.1 × 105 S/m at 10 vol % PVA with increased mechanical adhesion on polyethylene terephthalate and glass substrates. We studied the effects of the PVA molecular weight, hydrolyzation degree, and volume fraction. Composites with 10 vol % highly hydrolyzed PVA at a MW of 89-98 kDa had the highest conductivities and stabilities; highly hydrolyzed PVA even increased the conductivity of the hybrid particle layers. We propose the formation of hydrogen bonds between PVA and PEDOT:PSS that lead to demixing and the formation of stable, structured composites. Finally, we demonstrated the inkjet-printability of inks containing PVA in water with viscosities of 1.6-2.0 Pa s at 50.1 s-1 and prepared bending-resistant electrical leads.
RESUMO
We study the effect of additives on the colloidal stability of alkanethiol-coated gold nanoparticles. Cyclic amines and sulfides of different sizes were added to dispersions in decane at additive concentrations below 128 mM. Small-angle X-ray scattering (SAXS) indicated that tetrahydrothiophene reduced the agglomeration temperature, Tagglo, by up to 29 °C, a considerable increase in colloidal stability. Amines had a much weaker stabilizing effect of up to 2.5 °C. We found an unexpected maximum of stabilization for low additive concentrations, where Tagglo increased at concentrations above 64 mM. Molecular dynamics simulations were used to correlate these observations with the ligand shell structure. They excluded the physisorption of additives as a stabilization mechanism and suggested that sulfides replace hexadecanethiol on the AuNP surfaces by chemisorption. This hinders ligand ordering, thereby reducing Tagglo, which explains the stabilizing effect. Clustering of chemisorbed additive molecules at high concentration restabilized the ligand ordered state, explaining the detrimental effect of higher additive concentrations. The predictions of the simulations were confirmed by using thermogravimetric analyses and SAXS measurements of washed samples that indicated that the structure of the ligand shell itself, not the presence of physisorbed additives, changes Tagglo. Finally, we calculated potentials of mean force, which show that larger sulfide-based additives have a weaker affinity for the gold surface than smaller ones due to stronger steric hindrance. This explains why smaller cyclic sulfides were the most efficient stabilizers.
RESUMO
The expansion of T cells ex vivo is crucial for effective immunotherapy but currently limited by a lack of expansion approaches that closely mimic in vivo T cell activation. Taking inspiration from bottom-up synthetic biology, a new synthetic cell technology is introduced based on dispersed liquid-liquid phase-separated droplet-supported lipid bilayers (dsLBs) with tunable biochemical and biophysical characteristics, as artificial antigen presenting cells (aAPCs) for ex vivo T cell expansion. These findings obtained with the dsLB technology reveal three key insights: first, introducing laterally mobile stimulatory ligands on soft aAPCs promotes expansion of IL-4/IL-10 secreting regulatory CD8+ T cells, with a PD-1 negative phenotype, less prone to immune suppression. Second, it is demonstrated that lateral ligand mobility can mask differential T cell activation observed on substrates of varying stiffness. Third, dsLBs are applied to reveal a mechanosensitive component in bispecific Her2/CD3 T cell engager-mediated T cell activation. Based on these three insights, lateral ligand mobility, alongside receptor- and mechanosignaling, is proposed to be considered as a third crucial dimension for the design of ex vivo T cell expansion technologies.
RESUMO
The structure of supraparticles (SPs) is a key parameter for achieving advanced functionalities arising from the combination of different nanoparticle (NP) types in one hierarchical entity. However, whenever a droplet-assisted forced assembly approach is used, e.g., spray-drying, the achievable structure is limited by the inherent drying phenomena of the method. In particular, mixed NP dispersions of differently sized colloids are heavily affected by segregation during the assembly. Herein, the influence of the colloidal arrangement of Pt and SiO2 NPs within a single supraparticulate entity is investigated. A salt-based electrostatic manipulation approach of the utilized NPs is proposed to customize the structure of spray-dried Pt/SiO2 SPs. By this, size-dependent separation phenomena of NPs during solvent evaporation, that limit the catalytic performance in the reduction of 4-nitrophenol, are overcome by achieving even Pt NP distribution. Additionally, the textural properties (pore size and distribution) of the SiO2 pore framework are altered to improve the mass transfer within the material leading to increased catalytic activity. The suggested strategy demonstrates a powerful, material-independent, and universally applicable approach to deliberately customize the structure and functionality of multi-component SP systems. This opens up new ways of colloidal material combinations and structural designs in droplet-assisted forced assembly approaches like spray-drying.
RESUMO
We explore the potential of nanocrystals (a term used equivalently to nanoparticles) as building blocks for nanomaterials, and the current advances and open challenges for fundamental science developments and applications. Nanocrystal assemblies are inherently multiscale, and the generation of revolutionary material properties requires a precise understanding of the relationship between structure and function, the former being determined by classical effects and the latter often by quantum effects. With an emphasis on theory and computation, we discuss challenges that hamper current assembly strategies and to what extent nanocrystal assemblies represent thermodynamic equilibrium or kinetically trapped metastable states. We also examine dynamic effects and optimization of assembly protocols. Finally, we discuss promising material functions and examples of their realization with nanocrystal assemblies.
RESUMO
Mechanical metamaterials are known for their prominent mechanical characteristics such as programmable deformation that are due to periodic microstructures. Recent research trends have shifted to utilizing mechanical metamaterials as structural substrates to integrate with functional materials for advanced functionalities beyond mechanical, such as active sensing. This study reports on the ultra-stretchable kirigami piezo-metamaterials (KPM) for sensing coupled large deformations caused by in- and out-of-plane displacements using the lead zirconate titanate (PZT) and barium titanate (BaTiO3 ) composite films. The KPM are fabricated by uniformly compounding and polarizing piezoelectric particles (i.e., PZT and BaTiO3 ) in silicon rubber and structured by cutting the piezoelectric rubbery films into ligaments. Characterizes the electrical properties of the KPM and investigates the bistable mechanical response under the coupled large deformations with the stretching ratio up to 200% strains. Finally, the PZT KPM sensors are integrated into wireless sensing systems for the detection of vehicle tire bulge, and the non-toxic BaTiO3 KPM are applied for human posture monitoring. The reported kirigami piezo-metamaterials open an exciting venue for the control and manipulation of mechanically functional metamaterials for active sensing under complex deformation scenarios in many applications.
RESUMO
Self-healing nanocomposites can be generated by organic functionalization of inorganic nanoparticles and complementary functionalization of the polymer matrix, allowing reversible interactions between the two components. Here, we report on self-healing nanocomposites based on ionic interactions between anionic copolymers consisting of di(ethylene glycol) methyl ether methacrylate, sodium 4-(methacryloyloxy)butan-1-sulfonate, and cationically functionalized iron oxide nanoparticles. The materials exhibited hygroscopic behavior. At water contents < 6%, the shear modulus was reduced by up to 90%. The nanoparticle concentration was identified as a second factor strongly influencing the mechanical properties of the materials. Backscattered scanning electron microscopy and small-angle X-ray scattering measurements showed the formation of agglomerates in the size range of 100 nm to a few µm in diameter, independent of concentration, resulting in the disordering of the semi-crystalline ionic polymer blocks. These effects resulted in an increase in the shear modulus of the composite from 3.7 MPa to 5.6 MPa, 6.3 Mpa, and 7.5 MPa for 2, 10, and 20 wt% particles, respectively. Temperature-induced self-healing was possible for all composites investigated. However, only 36% of the maximum stress could be recovered in systems with a low nanoparticle content, whereas the original properties were largely restored (>85%) at higher particle contents.
RESUMO
Continuous and distributed monitoring of environmental parameters may pave the way for developing sustainable strategies to tackle climate challenges. State-of-the-art technologies, made with electronic systems, are often costly, heavy, and generate e-waste. Here, we propose a new generation of self-deployable, biocompatible, and luminescent artificial flying seeds for wireless, optical, and eco-friendly monitoring of environmental parameters (i.e., temperature). Inspired by natural Acer campestre plant seeds, we developed three-dimensional functional printed luminescent seed-like fliers, selecting polylactic acid as a biocompatible matrix and temperature as a physical parameter to be monitored. The artificial seeds mimic the aerodynamic and wind dispersal performance of the natural ones. The sensing properties are given by the integration of fluorescent lanthanide-doped particles, whose photoluminescence properties depend on temperature. The luminescent artificial flying seeds can be optically read from a distance using eye-safe near-infrared wavelengths, thus acting as a deployable sensor for distributed monitoring of topsoil environmental temperatures.
Assuntos
Clima , Sementes , Vento , TemperaturaRESUMO
The fabrication of nanocomposites containing magnetic nanoparticles is gaining interest as a model for application in small electronic devices. The self-assembly of block copolymers (BCPs) makes these materials ideal for use as a soft matrix to support the structural ordering of the nanoparticles. In this work, a high-molecular-weight polystyrene-b-poly(methyl methacrylate) block copolymer (PS-b-PMMA) was synthesized through anionic polymerization. The influence of the addition of different ratios of PMMA-coated FePt nanoparticles (NPs) on the self-assembled morphology was investigated using transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS). The self-assembly of the NPs inside the PMMA phase at low particle concentrations was analyzed statistically, and the negative effect of higher particle ratios on the lamellar BCP morphology became visible. The placement of the NPs inside the PMMA phase was also compared to theoretical descriptions. The magnetic addressability of the FePt nanoparticles inside the nanocomposite films was finally analyzed using bimodal magnetic force microscopy and proved the magnetic nature of the nanoparticles inside the microphase-separated BCP films.
RESUMO
We report on the unusual, advantageous ageing of flexible transparent electrodes (FTEs) that were self-assembled from oleylamine-capped gold nanospheres (AuNPs) by direct nanoimprinting of inks with different particle concentrations (cAu = 3 mg mL-1 to 30 mg mL-1). The resulting lines were less than 2.5 µm wide and consisted of disordered particle assemblies. Small-Angle X-ray Scattering confirmed that particle packing did not change with ink concentration. Plasma sintering converted the printed structures into lines with a thin, electrically conductive metal shell and a less conductive hybrid core. We studied the opto-electronic performance directly after plasma sintering and after fourteen days of storage at 22 °C and 55% rH in the dark. The mean optical transmittance TÌ400-800 in the range from 400 nm to 800 nm increased by up to ≈ 3%, while the sheet resistance Rsh strongly decreased by up to ≈ 82% at all concentrations. We correlated the changes with morphological changes visible in scanning and transmission electron microscopy and identified two sequential ageing stages: (I) post-plasma relaxation effects in and consolidation of the shell, and (II) particle re-organization, de-mixing, coarsening, and densification of the core with plating of Au from the core onto the shell, followed by solid-state de-wetting (ink concentrations cAu < 15 mg mL-1) or stability (cAu ≥ 15 mg mL-1). The plating of Au from the hybrid core improved the FTEs' Figure of Merit FOM = TÌ400-800·Rsh-1 by up to ≈ 5.8 times and explains the stable value of ≈ 3.3%·Ωsq-1 reached after 7 days of ageing at cAu = 30 mg mL-1.
RESUMO
Current environmental challenges and the shrinking fossil-fuel feedstock are important criteria for the next generation of polymer materials. In this context, we present a fully bio-based material, which shows promise as a thermoplastic elastomer (TPE). Due to the use of ß-farnesene and L-lactide as monomers, bio-based feedstocks, namely sugar cane and corn, can be used. A bifunctional initiator for the carbanionic polymerization was employed, to permit an efficient synthesis of ABA-type block structures. In addition, the "green" solvent MTBE (methyl tert-butyl ether) was used for the anionic polymerisation, enabling excellent solubility of the bifunctional anionic initiator. This afforded low dispersity (D=1.07 to 1.10) and telechelic polyfarnesene macroinitiators. These were employed for lactide polymerization to obtain H-shaped triblock copolymers. TEM and SAXS revealed clearly phase-separated morphologies, and tensile tests demonstrated elastic mechanical properties. The materials featured two glass transition temperatures, at - 66 °C and 51 °C as well as gyroid or cylindrical morphologies, resulting in soft elastic materials at room temperature.
RESUMO
One of the major limitations of flexible sensors is the loss of conductivity upon multiple stretching and bending cycles. Conducting fillers with two different geometries, carbon black and carbon nanotubes, were introduced in polydimethylsiloxane (PDMS) for physical insights into the structure formation of nanofillers by the application of periodic tensile stress. The loading of the nanofillers was selected beyond the percolation threshold to determine the cyclic stability of the resulting network channels. The surface chemistry of carbon nanotubes has been varied to understand the interfacial interactions at the molecular length scale. The combination of in situ stretching, annealing, and vis-à-vis conductometry of nanocomposite films with synchrotron-based ultra-small angle X-ray scattering experiments enables us to highlight the importance of the fractal dimensions of nanofillers for the molecular level interactions. The irreversible formation of nanofiller network geometries under cyclic stress and annealing was found to be responsible for the electrical properties of a flexible conducting film.
RESUMO
Solvent engineering is a powerful and versatile method to tune colloidal stability. Here, we link the molecular structure of apolar ligand shells on gold nanoparticles with their colloidal stability in solvent mixtures. The agglomeration temperature of the particles was measured with small-angle X-ray scattering. It depended on solvent composition and changed linearly for hexane-hexadecane mixtures, but nonlinearly for cyclohexane-hexadecane and hexanol-hexadecane mixtures. Molecular dynamics (MD) simulations indicate that agglomeration is dominated by temperature-dependent ligand order in the alkane mixtures and that the temperature at which the ligand shell orders depends on the solvent composition near the ligands, which can differ substantially from the bulk composition. Small-angle neutron scattering confirmed that, at intermediate solvent compositions above the agglomeration temperature, the fraction of cyclohexane near the ligands was larger than in the bulk. The enrichment of cyclohexane near the ligands stabilized their disordered state, which, consequently, led to the experimentally observed nonlinear trend of the agglomeration temperature. In contrast, hexanol was depleted from the ligand shell at all temperatures. This again stabilized the disordered state. Furthermore, we found that agglomeration at high hexanol fractions was driven by a solvophobic effect that exceeded the influence of ligand order. The results show that strong nonlinearities in the colloidal stability of nanoparticle dispersions in solvent mixtures are directly linked to the molecular details of ligand-solvent and solvent-solvent interactions, which can be used to precisely tune stability.
RESUMO
Hybrid dielectrics were prepared from dispersions of nanoparticles with gold cores (diameters from 2.9 nm to 8.2 nm) and covalently bound thiol-terminated polystyrene shells (5000 Da and 11 000 Da) in toluene. Their microstructure was investigated with small angle X-ray scattering and transmission electron microscopy. The particles arranged in nanodielectric layers with either face-centered cubic or random packing, depending on the ligand length and core diameter. Thin film capacitors were prepared by spin-coating inks on silicon substrates, contacted with sputtered aluminum electrodes, and characterized with impedance spectroscopy between 1 Hz and 1 MHz. The dielectric constants were dominated by polarization at the gold-polystyrene interfaces that we could precisely tune via the core diameter. There was no difference in the dielectric constant between random and supercrystalline particle packings, but the dielectric losses depended on the layer structure. A model that combines Maxwell-Wagner-Sillars theory and percolation theory described the relationship of the specific interfacial area and the dielectric constant quantitatively. The electric breakdown of the nanodielectric layers sensitively depended on particle packing. A highest breakdown field strength of 158.7 MV m-1 was found for the sample with 8.2 nm cores and short ligands that had a face-centered cubic structure. Breakdown apparently is initiated at the microscopic maxima of the electric field that depends on particle packing. The relevance of the results for industrially produced devices was demonstrated on inkjet printed thin film capacitors with an area of 0.79 mm2 on aluminum coated PET foils that retained their capacity of 1.24 ± 0.01 nF@10 kHz during 3000 bending cycles.
RESUMO
Ionic liquids are attractive liquid materials for many advanced applications. For targeted design, in-depth knowledge about their structure-property-relations is urgently needed. We prepared a set of novel protic ionic liquids (PILs) with a guanidinium cation with either an ether or alkyl side chain and different anions. While being a promising cation class, the available data is insufficient to guide design. We measured thermal and transport properties, nuclear magnetic resonance (NMR) spectra as well as liquid and crystalline structures supported by ab initio computations and were able to obtain a detailed insight into the influence of the anion and the ether substitution on the physical and spectroscopic properties. For the PILs, hydrogen bonding is the main interaction between cation and anion and the H-bond strength is inversely related to the proton affinity of the constituting acid and correlated to the increase of 1H and 15N chemical shifts. Using anions from acids with lower proton affinity leads to proton localization on the cation as evident from NMR spectra and self-diffusion coefficients. In contrast, proton exchange was evident in ionic liquids with triflate and trifluoroacetate anions. Using imide-type anions and ether side groups decreases glass transitions as well as fragility, and accelerated dynamics significantly. In case of the ether guanidinium ionic liquids, the conformation of the side chain adopts a curled structure as the result of dispersion interactions, while the alkyl chains prefer a linear arrangement.
RESUMO
Engineered living materials (ELMs) encapsulate microorganisms within polymeric matrices for biosensing, drug delivery, capturing viruses, and bioremediation. It is often desirable to control their function remotely and in real time and so the microorganisms are often genetically engineered to respond to external stimuli. Here, we combine thermogenetically engineered microorganisms with inorganic nanostructures to sensitize an ELM to near infrared light. For this, we use plasmonic gold nanorods (AuNR) that have a strong absorption maximum at 808 nm, a wavelength where human tissue is relatively transparent. These are combined with Pluronic-based hydrogel to generate a nanocomposite gel that can convert incident near infrared light into heat locally. We perform transient temperature measurements and find a photothermal conversion efficiency of 47 %. Steady-state temperature profiles from local photothermal heating are quantified using infrared photothermal imaging and correlated with measurements inside the gel to reconstruct spatial temperature profiles. Bilayer geometries are used to combine AuNR and bacteria-containing gel layers to mimic core-shell ELMs. The thermoplasmonic heating of an AuNR-containing hydrogel layer that is exposed to infrared light diffuses to the separate but connected hydrogel layer with bacteria and stimulates them to produce a fluorescent protein. By tuning the intensity of the incident light, it is possible to activate either the entire bacterial population or only a localized region.
Assuntos
Nanoestruturas , Nanotubos , Humanos , Ouro/química , Nanotubos/química , Diagnóstico por Imagem , HidrogéisRESUMO
This study concerns the development of sustainable design strategies of aqueous electrolytes for redox flow batteries using redox-active organic materials. A green spontaneous grafting reaction occurs between a redox-active organic radical and an electrochemically activated structural modifier at room temperature through a simple mixing step. Then, a physical mixing method is used to formulate a structured aqueous electrolyte and enables aqueous solubilization of the organic solute from below 0.5 to 1.5â m beyond the conventional dissolution limit. The as-obtained concentrated mixture can be readily used as catholyte for a redox flow battery. A record high discharge cell voltage (1.6â V onset output voltage) in aqueous non-hybrid flow cell is attained by using the studied electrolytes.
RESUMO
Gravity can affect the agglomeration of nanoparticles by changing convection and sedimentation. The temperature-induced agglomeration of hexadecanethiol-capped gold nanoparticles in microgravity (µ g) is studied at the ZARM (Center of Applied Space Technology and Microgravity) drop tower and compared to their agglomeration on the ground (1 g). Nonpolar nanoparticles with a hydrodynamic diameter of 13 nm are dispersed in tetradecane, rapidly cooled from 70 to 10 °C to induce agglomeration, and observed by dynamic light scattering at a time resolution of 1 s. The mean hydrodynamic diameters of the agglomerates formed after 8 s in microgravity are 3 times (for low initial concentrations) to 5 times (at high initial concentrations) larger than on the ground. The observations are consistent with an agglomeration process that is closer to the reaction limit on thground and closer to the diffusion limit in microgravity.
Assuntos
Nanopartículas Metálicas , Ausência de Peso , Ouro , Difusão Dinâmica da Luz , TemperaturaRESUMO
We directed the self-assembly of nanoscale colloids via direct nanoimprint lithography to create flexible transparent electrodes (FTEs) with metal line widths below 3 µm in a roll-to-roll-compatible process. Gold nanowires and nanospheres with oleylamine shells were imprinted with soft silicone stamps, arranged into grids of parallel lines, and converted into metal lines in a plasma process. We studied the hierarchical structure and opto-electronic performance of the resulting grids as a function of particle geometry and concentration. The performance in terms of optical transmittance was dominated by the line width. Analysis of cross-sections indicated that plasma sintering only partially removed the insulating ligands and formed lines with thin conductive shells and a non-conductive core. We provide evidence that the self-assembly of high-aspect nanowires can compensate for defects of the stamp and substrate irregularities during imprinting, while spheres cannot. The wire-based electrodes thus outperformed the sphere-based electrodes at ratios of optical transmittance to sheet resistance of up to ≈ 0.9% Ωsq -1, while spheres only reached ≈ 0.55% Ωsq -1.