Effect of Position of Donor Units and Alkyl Groups on Dye-Sensitized Solar Cell Device Performance: Indoline-Aniline Donor-Based Visible Light Active Unsymmetrical Squaraine Dyes.

Indoline (In) and aniline (An) donor-based visible light active unsymmetrical squaraine (SQ) dyes were synthesized for dye-sensitized solar cells (DSSCs), where the position of An and In units was changed with respect to the anchoring group (carboxylic acid) to have In-SQ-An-CO2H and An-SQ-In-CO2H sensitizers, AS1-AS5. Linear or branched alkyl groups were functionalized with the N atom of either In or An units to control the aggregation of the dyes on TiO2. AS1-AS5 exhibit an isomeric π-framework where the squaric acid unit is placed in the middle, where AS2 and AS5 dyes possess the anchoring group connected with the An donor, and AS1, AS3, and AS4 dyes having the anchoring group connected with the In donor. Hence, the conjugation between the middle squaric acid acceptor unit and the anchoring -CO2H group is short for AS2, AS5, and AK2 and longer for AS1, AS3, and AS4 dyes. AS dyes showed absorption between 501 and 535 nm with extinction coefficients of 1.46-1.61 × 105 M-1 cm-1. Further, the isomeric π-framework of An-SQ-In-CO2H and In-SQ-An-CO2H exhibited by means of changing the position of In and An units a bathochromic shift in the absorption properties of AS2 and AS5 compared to the AS1, AS3, and AS4 dyes. The DSSC device fabricated with the dyes contains short acceptor-anchoring group distance (AS2 and AS5) showed high photovoltaic performances compared to the dyes having longer distance (AS1, AS3, and AS4) with the iodolyte (I-/I3-) electrolyte. DSSC device efficiencies of 5.49, 6.34, 6.16, and 5.57% have been achieved for AS1, AS2, AS3, and AS4 dyes, respectively; without chenodeoxycholic acid (CDCA), small changes have been observed in the device performance of the AS dyes with CDCA. Significant changes have been noted in the DSSC parameters (open-circuit voltage VOC, short-circuit current JSC, fill factor ff, and efficiency η) for the AS5 dye while sensitized with CDCA and showed highest DSSC efficiency of 8.01% in the AS dye series. This study revealed the potential of shorter SQ acceptor-anchoring group distance over the longer one and the importance of alkyl groups on the overall DSSC device performance for the unsymmetrical squaraine dyes.

Far-red active unsymmetrical squaraine dyes containing N-arylated indoline donors for dye sensitized solar cells.

Squaraine dyes possess sharp far-red active transition with high extinction coefficient and form aggregates on TiO2 surface. Aggregation of dyes on TiO2 has been considered as a detrimental factor for DSSC device performance, which can be controlled by appending alkyl groups to the dye structures. Hence by integrating alkylated (alkyl groups with both in-plane and out-of-plane) aryl group with indoline moiety to make it compatible with other electrolytes and for controlling the dye-aggregation, a series of squaraine acceptor-based dyes SQA4-6 have been designed and synthesized. SQA4-6 dyes showed absorption between 642 and 653 nm (λmax ), photophysical and electrochemical studies indicated that the HOMO energy levels of this sets of dyes are well aligned with the potentials of I- / I 3 - $$ {\mathrm{I}}_3^{-} $$ and [Co(bpy)3 ]2+/3+ redox shuttles for better dye regeneration process. DSSC device efficiency of 3% has been achieved for SQA5 dye with iodolyte (I- / I 3 - $$ {\mathrm{I}}_3^{-} $$ ) electrolyte in the presence of 0.3 mM of chenodeoxycholic acid (CDCA). The IPCE profile of DSSC device fabricated with SQA4-6 dyes indicated the contribution of aggregated structures for the photocurrent generation.

Visible-Light-Active Unsymmetrical Squaraine Dyes with Pyridyl Anchoring Groups for Dye-Sensitized Solar Cells.

Visible-light-active alkyl group-wrapped unsymmetrical squaraine dyes SD1-SD3 were synthesized, featuring an indoline donor and pyridine and carboxylic acid anchoring groups. Their photophysical, electrochemical, and photovoltaic characteristics were examined by fabricating a dye-sensitized solar cell (DSSC) device. Both carboxylic acid and pyridine anchoring groups containing squaraine dyes SD3 and SD2 possess similar photophysical and electrochemical characteristics. However, their photovoltaic performances were completely different. The SD3 dye with the carboxylic acid anchoring group displayed a DSSC device efficiency of 7.20% (VOC 0.81 V; JSC 12.29 mA/cm2) using iodolyte (I-/I3-) electrolyte, compared to SD1 (VOC 0.659 V; JSC 4.97 mA/cm2; and η - 2.34%) and SD2 (VOC 0.629 V; JSC 1.68 mA/cm2; and η - 0.84%), which were featured with pyridyl anchoring groups. These results were attributed to dye loading on the Lewis and Brønsted acidic sites of TiO2 and the importance of aggregated structures for photocurrent generation. In the incident photon-to-current efficiency (IPCE) analysis, SD1 dye-sensitized devices exhibited photocurrent generation from both monomeric and aggregated dyes on the TiO2 surface. In contrast, SD2 showed photocurrent generation solely from aggregated states. Despite the introduction of long alkyl chains to reduce dye aggregation and charge recombination, the results indicated preferential charge injection from only the aggregated SD2 dye on TiO2. Fluorescence-quenching experiments indicated an efficient charge transfer from the aggregated SD2 dye to TiO2 compared to that of the monomeric dye. Cosensitization, a method to enhance the light-harvesting efficiency and photocurrent generation in DSSCs, was explored by simultaneously cosensitizing pyridyl-based dyes (SD1 and SD2) with a blue-colored carboxylic acid-based squaraine dye SD4. IPCE analysis demonstrated that both SD1 and SD4 contributed to generating a photocurrent of 9.11 mA/cm2. The sequential cosensitization of SD1 and SD4 with the coadsorbent CDCA showed the highest performance, with a VOC of 0.663 V, a JSC of 11.43 mA/cm2, and an efficiency (η) of 5.20%.

Electrocatalytic hydrogen evolution mediated by an organotelluroxane macrocycle stabilized through secondary interactions.

A discrete liphophilic organotelluroxane macrocycle has been found to catalyse the hydrogen evolution reaction (HER) by proton reduction efficiently. The macrocycle is synthesized via chloride abstraction from bis(p-methoxyphenyl) tellurium dichloride (p-MeOC6H5)2TeCl2 (1) by silver salts AgMX4 (MX4 = BF4-, and ClO4-) resulting in in situ generated di-cationic tetraorganoditelluroxane units; two such units are held together by two weak anions µ2-MX4, bridging to form 12-membered di-cationic macrocycles [((p-MeO-C6H4)2Te)2(µ-O)(µ2-F2BF2)2]2+ (2) and [((p-MeO-C6H4)2Te)2(µ-O)(µ2-O2ClO2)2]2+ (3) stabilized via Te-(µ2-BF4/ClO4), with secondary interactions. The charge is balanced by the presence of two more anions, one above and another below the plane of the macrocycle. Similar reaction at higher temperatures leads to the formation of telluronium salts R3TeX [X = BF4- (4), ClO4- (5)] as a major product. The BF4- anion containing macrocycle and telluronium salt were monitored using 19F NMR. HRMS confirmed the structural stability of all the compounds in the solution state. The organotelluroxane macrocycle 2 has been found to act as an efficient electrocatalyst for proton reduction in an organic medium in the presence of p-toluene sulfonic acid as a protic source.

Isomer Effect on Energy Storage of π-Extended S-Shaped Double[6]Heterohelicene.

Recently, chiral and nonplanar cutouts of graphene have been the favorites due to their unique optical, electronic, and redox properties and high solubility compared with their planar counterparts. Despite the remarkable progress in helicenes, π-extended heterohelicenes have not been widely explored. As an anode in a lithium-ion battery, the racemic mixture of π-extended double heterohelical nanographene containing thienothiophene core exhibited a high lithium storage capability, attaining a specific capacity of 424 mAh g-1 at 0.1 A g-1 with excellent rate capability and superior long-term cycling performance over 6000 cycles with negligible fade. As a first report, the π-extended helicene isomer (PP and MM), with the more interlayer distance that helps faster diffusion of ions, has exhibited a high capacity of 300 mAh g-1 at 2 A g-1 with long-term cycling performance over 1500 cycles compared to the less performing MP and PM isomer and racemic mixture (150 mAh g-1 at 2 A g-1 ). As supported by single-crystal X-ray analysis, a unique molecular design of nanographenes with a fixed (helical) molecular geometry, avoiding restacking of the layers, renders better performance as an anode in lithium-ion batteries. Interestingly, the recycled nanographene anode material displayed comparable performance.

D-A-D-based Unsymmetrical Thiosquaraine Dye for the Dye-Sensitized Solar Cells†.

In dye-sensitized solar cell, modulating the electronic properties of the sensitizer by varying the donor, π-spacer, acceptor and anchoring groups help optimizing the structure of the dye for better device performance. Here, a donor-acceptor-donor-based unsymmetrical thiosquaraine sensitizer (SQ5S) has been designed and synthesized. Photophysical, electrochemical, theoretical and photovoltaic characterizations of SQ5S dye have been compared with its oxygen analog, SQ5. The incorporation of the sulfur atom in the acceptor unit of SQ5S dye showed an intense peak at 688 nm, which was 38 nm of red-shifted and showed the panchromatic light harvesting response with the onset of 850 nm compared with SQ5 dye. The LUMO and HOMO energy levels are well aligned with the conduction band of TiO2 and the redox potential of electrolyte for the charge injection and the dye-regeneration processes, respectively. Photovoltaic efficiency of 1.51% (VOC 610 mV, JSC 3.07 mA cm-2 , ff 81%) has been achieved for SQ5S dye, whereas SQ5 showed the device performance of 5.43% (VOC 723 mV, JSC 9.3 mA cm-2 , ff 80%). The decreased device performance for the dye SQ5S has been attributed to the favorable intersystem crossing process associated with the photoexcited SQ5S that reduces the driving force for the charge injection process.

Solvent-Dependent Functional Aggregates of Unsymmetrical Squaraine Dyes on TiO2 Surface for Dye-Sensitized Solar Cells.

Alkyl group wrapped donor-acceptor-donor (D-A-D) based unsymmetrical squaraine dyes SQ1, SQ5, and SQS4 were used to evaluate the effect of sensitizing solvents on dye-sensitized solar cell (DSSC) efficiency. A drastic change in DSSC efficiency was observed when the photo-anodes were sensitized in acetonitrile (bad solvent when considering dye solubility) and chloroform (good solvent) with an Iodolyte (I-/I3-) electrolyte. The DSSC device sensitized with squaraine dyes in acetonitrile showed better photovoltaic performance with enhanced photocurrent generation and photovoltage compared to the device sensitized in chloroform. In a good sensitizing solvent, dyes with long hydrophobic alkyl chains are deleterious forming aggregates on the TiO2 surface, which results in an incident photon-to-current conversion efficiency (IPCE) response mostly from monomeric and dimeric structures. Meanwhile, a bad sensitizing solvent facilitates the formation of well-packed self-assembled structures on the TiO2 surface, which are responsible for a broad IPCE response and high device efficiencies. The photoanode sensitized in the bad sensitizing solvent showed enhanced VOC values of 642, 675, and 699 mV; JSC values of 6.38, 11.1, and 11.69 mA/cm2; and DSSC device efficiencies of 3.0, 5.63, and 6.13% for the SQ1, SQ5, and SQS4 dyes in the absence of a coadsorbent (chenodeoxycholic acid (CDCA)), respectively, which were further enhanced by CDCA addition. Meanwhile, the photoanode sensitized in the good sensitizing solvent showed relatively low photovoltaic VOC values of 640, 652, and 650 mV; JSC values of 5.78, 6.79, and 6.24 mA/cm2; and device efficiencies of 2.73, 3.35, and 3.20% for SQ1, SQ5, and SQS4 in the absence of CDCA, respectively, which were further varied with equivalents of CDCA. The best DSSC device efficiencies of 6.13 and 3.20% were obtained for SQS4 without CDCA, where the dye was sensitized in acetonitrile (bad) and chloroform (good) sensitizing solvents, respectively.

Conversion of curved assemblies into two dimensional sheets.

The design and preparation of organic two dimensional (O2D) sheets and their conversion to curved nanostructures is in its infancy. To convert a flat structure into a curved structure, the molecule must have multiple interaction possibilities and an in-built twist. The conjugated small molecule iso-Indigo (i-Indigo) comprises two phenyl rings that are twisted (the dihedral angle is 15°) at the junction. The i-Indigo has been connected with moieties that impart hydrogen bonding and van der Waals interactions. Due to the presence of the π cloud in i-Indigo, π-π interactions are also present in the molecule. While all three interactions are in operation, rings and toroids are formed. Upon addition of hydrogen bonding competing solvents, the rings and toroids unravel to form O2D sheets. Control molecules that don't have hydrogen bonding moieties and π-π interactions form random assemblies. Please note that the rings, toroids and O2D sheets are formed in a single solvent by simple dissolution, unlike previous approaches that involve multiple steps and solvents.

Modulated photochemical reactivities of O-acetylated (3',5'-dimethoxyphenyl)heteroaryl acyloin derivatives under direct irradiation and photo-induced electron transfer conditions.

3',5'-Dimethoxybenzoin esters are important photoremovable protecting groups which form 2-phenylbenzofuran derivatives upon photo-release. We utilized a similar concept to test a photochemical method of installing a benzofuran moiety to the conjugated backbone by subjecting O-acetylated (3',5'-dimethylphenyl)heteroaryl acyloin derivatives through direct photo irradiation and a photo-induced electron transfer reaction. These photochemical methods were explored for a variety of heteroaromatic substrates appended on the ketone part of the O-acetylated cross-acyloin derivatives. The furan, thiophene and bithiophene derivatives led to the expected cyclized (benzofuran capped) products but the derivatives with extended conjugation decomposed under direct irradiation. However, under irradiation in the presence of an electron donor such as triethylamine, the extended acyloin derivatives afforded both cyclized and deacetoxylated products. The semiconducting nature of the extended cyclized products was also explored and tested for solution-processed organic field effect transistors, providing a maximum hole mobility of 1.3 × 10-6 cm2 V-1 s-1.

Experimental and Theoretical Investigations of Different Diketopyrrolopyrrole-Based Polymers.

Diketopyrrolopyrrole (DPP)-based polymers are often considered as the most promising donor moiety in traditional bulk heterojunction solar cell devices. In this paper, we report the synthesis, characterization of various DPP-based copolymers with different molecular weights, and polydispersity where other aromatic repeating units (phenyl or thiophene based) are connected by alternate double bonds or triple bonds. Some of the copolymers were used for device fabrication and the crucial parameters such as fill factor (FF) and open circuit voltage (V oc) were calculated. The density functional theory was used to optimize the geometries and deduce highest occupied molecular orbital-lowest unoccupied molecular orbital gaps of all the polymers and theoretically predict their optical and electronic properties. Optical properties of all the polymers, electrochemical properties, and band gaps were also obtained experimentally and compared with the theoretically predicted values.

Self-Assembled Spheres, Flowers, and Fibers from the Same Backbone and Similar Side Chains.

Rylene imides (RIs) self-assemble into various nanostructures. Often, the synthesis of unsymmetrical RIs (URIs) is required to achieve nanostructures. However, the synthesis of URIs is nontrivial. Thus, a structurally similar alternative is desirable. iso-Indigo (i-indigo) has a π core and lactam rings that are structurally similar to the RIs. Unsymmetrical iso-indigo (i-indigo) can be easily synthesized by condensing oxindole and isatin. We have synthesized a series of unsymmetrical i-indigo molecules. In these molecules, the π-π interaction, hydrogen bonding, and van der Waals interactions are in operation. Because of these, the molecules self-assemble into spheres, fibers, and dahlia flower morphologies. If the hydrogen bonding interaction is disrupted, then all of them form fibers. Control experiments indicate that the complete absence of hydrogen bonding is deleterious to self-assembly. We also show that the lower analogs of i-indigo are not sufficient to form self-assembled nanostructures.

A polymer and graphene layer to increase dye regeneration and suppress back electron transfer in dye sensitized solar cells.

Dye regeneration was improved by using an optimum quantity of graphene, which was dispersed in a polymer that suppresses back electron transfer. Using this approach, DSSCs with an efficiency of 10.4% have been fabricated.

ZnO-ZnS Heterojunctions: A Potential Candidate for Optoelectronics Applications and Mineralization of Endocrine Disruptors in Direct Sunlight.

Simple solution combustion synthesis was adopted to synthesize ZnO-ZnS (ZSx) nanocomposites using zinc nitrate as an oxidant and a mixture of urea and thiourea as a fuel. A large thiourea/urea ratio leads to more ZnS in ZSx with heterojunctions between ZnS and ZnO and throughout the bulk; tunable ZnS crystallite size and textural properties are an added advantage. The amount of ZnS in ZSx can be varied by simply changing the thiourea content. Although ZnO and ZnS are wide band gap semiconductors, ZSx exhibits visible light absorption, at least up to 525 nm. This demonstrates an effective reduction of the optical band gap and substantial changes in its electronic structure. Raman spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and secondary-ion mass spectrometry results show features due to ZnO and ZnS and confirm the composite nature with heterojunctions. The above mentioned observations demonstrate the multifunctional nature of ZSx. Bare ZSx exhibits a promising sunlight-driven photocatalytic activity for complete mineralization of endocrine disruptors such as 2,4-dichlorophenol and endosulphan. ZSx also exhibits photocurrent generation at no applied bias. Dye-sensitized solar cell performance evaluation with ZSx shows up to 4% efficiency and 48% incident photon conversion efficiency. Heterojunctions observed between ZnO and ZnS nanocrystallites in high-resolution transmission electron microscopy suggest the reason for effective separation of electron-hole pairs and their utilization.

Flexible Microsupercapacitors Using Silk and Cotton Substrates.

Flexible microsupercapacitors (MSCs) are needed to power ultrasmall wearable electronic devices. Silk cocoons comprise microfibers of silk, which is an attractive natural resource to fabricate MSCs. These fibers are insulators; hence, they must be converted to conducting surfaces. Polyphenols from green tea have been used as a protective layer that also acted as a reducing agent for silver ions. The reduction of silver ions resulted in the formation of silver nanoparticles that subsequently reduced gold ions to gold. The gold film imparts conductivity to the silk fiber without affecting the mechanical strength of the silk fiber. The mechanical strength of uncoated silk fiber and gold coated silk fiber were found to be 5.2 and 5 GPa, respectively. A pseudocapacitive polymer, poly(3,4-ethylenedioxythiophene), was used as the active material to fabricate MSCs. The MSCs showed an impressive gravimetric capacitance of 500 F/g and areal capacitance of 62 mF/cm2. The power and energy densities were calculated to be 2458 W/kg and 44 Wh/kg, respectively. The device was coiled on a cylinder, and the performance of the device was found to be same as that of the uncoiled device. To demonstrate that the approach is not specific to silk, we also coated gold on cotton fibers using the protocol used to coat gold on silk. Coiled and uncoiled supercapacitors were fabricated using PEDOT coated cotton fibers. The gravimetric capacitance was found to be 250 F/g with energy and power densities of 5.5 Wh/kg and 1118 W/kg, respectively. We have also demonstrated that the devices can be connected in parallel and series to improve the performance of the miniaturized devices.

Selenium-Containing Fused Bicyclic Heterocycle Diselenolodiselenole: Field Effect Transistor Study and Structure-Property Relationship.

The first application of the diselenolodiselenole (C4Se4) heterocycle as an active organic field effect transistor materials is demonstrated here. C4Se4 derivatives (2a-2d) were obtained by using a newly developed straightforward diselenocyclization protocol, which includes the reaction of diynes with selenium powder at elevated temperature. C4Se4 derivatives exhibit strong donor characteristics and planar structure (except 2d). The atomic force microscopic analysis and thin-film X-ray diffraction pattern of compounds 2a-2d indicated the formation of distinct crystalline films that contain large domains. A scanning electron microscopy study of compound 2b showed development of symmetrical grains with an average diameter of 150 nm. Interestingly, 2b exhibited superior hole mobility, approaching 0.027 cm(2) V(-1) s(-1) with a transconductance of 9.2 µS. This study correlate the effect of π-stacking, Se···Se intermolecular interaction, and planarity with the charge transport properties and performance in the field effect transistor devices. We have shown that the planarity in C4Se4 derivatives was achieved by varying the end groups attached to the C4Se4 core. In turn, optoelectronic properties can also be tuned for all these derivatives by end-group variation.

Disassembly of micelles to impart donor and acceptor gradation to enhance organic solar cell efficiency.

A transparent, conducting and low surface energy surface was prepared by disassembly of anionic micelles, which altered the orientation of the donor polymer and imparted gradation between the donor and acceptor. This configuration increased the solar cell device efficiency.

Conjugated porous polymers as precursors for electrocatalysts and storage electrode materials.

Conjugated porous polymers were used as precursors to prepare nitrogen and sulphur doped carbon atoms, which were then used for oxygen reduction and energy storage.

Phenols from green tea as a dual functional coating to prepare devices for energy storage and molecular separation.

Polyphenols from green tea were used to electrolessly deposit gold on silk cocoons (SCs) and nanoporous aluminum oxide (AAO) templates. The gold coated cocoons were used as electrodes in supercapacitors and showed a capacitance as high as 254 F g(-1) and a specific power of 2287 W kg(-1). A metal coated AAO template was used for molecular separation.

Seeded on-surface supramolecular growth for large area conductive donor-acceptor assembly.

Charge transport features of organic semiconductor assemblies are of paramount importance. However, large-area extended supramolecular structures of donor-acceptor combinations with controlled self-assembly pathways are hardly accessible. In this context, as a representative example, seeded on-surface supramolecular growth of tetrathiafulvalene and tetracyano-p-quinodimethane (TTF-TCNQ) using active termini of solution-formed sheaves has been introduced to form an extended assembly. We demonstrate for the first time, the creation of a large-area donor-acceptor assembly on the surface, which is practically very tedious, using a seeded, evaporation-assisted growth process. The excellent molecular ordering in this assembly is substantiated by its good electrical conductivity (~10⁻² S cm⁻¹). The on-surface assembly via both internally formed and externally added sheaf-like seeds open new pathways in supramolecular chemistry and device applications.

Organic soluble and uniform film forming oligoethylene glycol substituted BODIPY small molecules with improved hole mobility.

Judiciously chosen side chains of conjugated molecules have a positive impact on charge transport properties when used as the active material in organic electronic devices. Amongst the side chains, oligoethylene glycols (OEGs) have been relatively unexplored due to their hydrophilic nature. OEGs also affect the smooth film formation of conjugated molecules, which preclude device fabrication. However, X-ray diffraction studies have shown that OEGs facilitate intermolecular contact, which is a desirable property for the fabrication of organic electronic devices. Thus the challenge is to design and synthesize organic solvent soluble and uniform film forming conjugated molecules with OEG side chains. We have designed and synthesized conjugated small molecules (CSMs) comprising BODIPY as acceptor and triphenylamine as donor with an OEG side chain. This molecule forms smooth films when processed from organic solvents. In order to understand the impact of the OEG side chain, we have also synthesized alkyl chain analogs. All the molecules exhibit exactly the same HOMO and LUMO energy levels, but the packing in the solid state is different. CSM with methyl side chains exhibit an inter planar distance of 4.15 Å. Contrary to this, the OEG side chain containing CSM showed an inter planar spacing of 4.30 Å, which is 0.2 Å less than the alkyl side chain comprising CSMs. Please note that the length of the hydrophobic and hydrophilic side chains is the same. Interestingly, the OEG side chain comprising CSM showed two orders of higher hole carrier mobilities compared to all the other derivatives. The same molecule also showed an extremely low threshold voltage of -0.27 V indicating the OEG side chains' favourable interaction between substrate as well as between molecules.