Flame-Retardant Glass Fiber-Reinforced Epoxy Resins with Phosphorus-Containing Bio-Based Benzoxazines and Graphene.

This paper presents a study of the flammability and thermal decomposition products of glass fiber-reinforced epoxy resin (GFRER) with the addition of cardanol-based phosphorus-containing benzoxazine monomer (CBz) and graphene and their combinations in different proportions (up to 20 wt.%). The addition of CBz alone or in combination with graphene resulted in an increase in the limiting oxygen index (LOI) and self-extinguishing in the UL-94 HB test. The flame-retardant samples had better tensile mechanical properties than the sample without additives. The differential mass-spectrometric thermal analysis (DMSTA) of the thermal decomposition products of GFRER without additives and with the addition of CBz and graphene was carried out. CBz addition promoted the thermal decomposition of high-molecular-weight products of epoxy resin decomposition in the condensed phase and at the same time decreased the time of release of low-molecular-weight thermal decomposition products into the gas phase. Graphene addition resulted in an increase in the relative intensities of high-molecular-mass peaks compared to GFRER without additives.

The Effect of Flame-Retardant Additives DDM-DOPO and Graphene on Flame Propagation over Glass-Fiber-Reinforced Epoxy Resin under the Influence of External Thermal Radiation.

The flammability of various materials used in industry is an important issue in the modern world. This work is devoted to the study of the effect of flame retardants, graphene and DDM-DOPO (9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide-4,4'-diamino-diphenyl methane), on the flammability of glass-fiber-reinforced epoxy resin (GFRER). Samples were made without additives and with additives of fire retardants: graphene and DDM-DOPO in various proportions. To study the flammability of the samples, standard flammability tests were carried out, such as thermogravimetric analysis, the limiting oxygen index (LOI) test, and cone calorimetry. In addition, in order to test the effectiveness of fire retardants under real fire conditions, for the first time, the thermal structure of downward flame propagation over GFRER composites was measured using thin thermocouples. For the first time, the measured thermal structure of the flame was compared with the results of numerical simulations of flame propagation over GFRER.

Past COVID-19: The Impact on IVF Outcomes Based on Follicular Fluid Lipid Profile.

Follicular fluid is an important component of follicle growth and development. Negative effects of COVID-19 on follicular function are still open. The aim of this work was to study the features of the lipid profile of follicular fluid and evaluate the results of the in vitro fertilization (IVF) program in women after COVID-19 to identify biomarkers with prognostic potential. The study involved samples of follicular fluid collected from 237 women. Changes in the lipid composition of the follicular fluid of patients who underwent COVID-19 in mild and severe forms before entering the IVF program and women who did not have COVID-19 were studied by mass spectrometry. Several lipids were identified that significantly changed their level. On the basis of these findings, models were developed for predicting the threat of miscarriage in patients who had a severe course of COVID-19 and models for predicting the success of the IVF procedure, depending on the severity of COVID-19. Of practical interest is the possibility of using the developed predictive models in working with patients who have undergone COVID-19 before entering the IVF program. The results of the study suggest that the onset of pregnancy and its outcome after severe COVID-19 may be associated with changes in lipid metabolism in the follicular fluid.

Investigation of the Technological Possibility of Manufacturing Volumetric Shaped Ductile Cast Iron Products in Open Dies.

Information about the technological possibility of stamping in open dies, round-shaped forgings made of ductile cast iron, is outlined herein. Cast iron's propensity for plastic deformation under complex loading conditions is analyzed from the standpoint of the morphology of graphite inclusions, depending on the degree and mechanical scheme of deformation. The research methodology included: the choice of a brand of cast iron with spherical graphite and the technological process of its deformation; mathematical modeling of the deformation process using the DEFORM-3D software package; stamping of an experimental batch of forgings; and microstructural studies of the forging material, together with the data of its stress-strain state and the direction of flow of the material. Under the conditions of comprehensive compression of the workpiece material at the beginning of the deformation process, lateral pressure was created from the tool walls. It was carried out by selecting the size and shape of the initial blank by mathematical modeling. When analyzing the morphology of graphite inclusions, the stress state scheme was determined as the main influencing factor. The greatest change in the shape and size of graphite inclusions of cast iron, including their crushing, corresponds to the condition of the disappearance of all-round compression. When stamping in open dies, this occurs in the area where the material exits from the stamp engraving into the flash gutter. In the process of forming, cast iron showed the possibility of deformation in the deformation intensity index εi = 2.5.