Anionic Sublattices in Halide Solid Electrolytes: A Case Study with the High-Pressure Phase of Li3ScCl6.

The Li3MX6 compounds (M=Sc, Y, In; X=Cl, Br) are known as promising ionic conductors due to their compatibility with typical metal oxide cathode materials. In this study, we have successfully synthesized γ-Li3ScCl6 using high pressure for the first time in this family. Structural analysis revealed that the high-pressure polymorph crystallizes in the polar and chiral space group P63mc with hexagonal close-packing (hcp) of anions, unlike the ambient-pressure α-Li3ScCl6 and its spinel analog with cubic closed packing (ccp) of anions. Investigation of the known Li3MX6 family further revealed that the cation/anion radius ratio, rM/rX, is the factor that determines which anion sublattice is formed and that in γ-Li3ScCl6, the difference in compressibility between Sc and Cl exceeds the ccp rM/rX threshold under pressure, enabling the ccp-to-hcp conversion. Electrochemical tests of γ-Li3ScCl6 demonstrate improved electrochemical reduction stability. These findings open up new avenues and design principles for lithium solid electrolytes, enabling routes for materials exploration and tuning electrochemical stability without compositional changes or the use of coatings.

Double-Layered Perovskite Oxyfluoride Cathodes with High Capacity Involving O-O Bond Formation for Fluoride-Ion Batteries.

Developing electrochemical high-energy storage systems is of crucial importance toward a green and sustainable energy supply. A promising candidate is fluoride-ion batteries (FIBs), which can deliver a much higher volumetric energy density than lithium-ion batteries. However, typical metal fluoride cathodes with conversion-type reactions cause a low-rate capability. Recently, layered perovskite oxides and oxyfluorides, such as LaSrMnO4 and Sr3Fe2O5F2, have been reported to exhibit relatively high rate performance and cycle stability compared to typical metal fluoride cathodes with conversion-type reactions, but their discharge capacities (∼118 mA h/g) are lower than those of typical cathodes used in lithium-ion batteries. Here, we show that double-layered perovskite oxyfluoride La1.2Sr1.8Mn2O7-δF2 exhibits (de) intercalation of two fluoride ions to rock-salt slabs and further (de) intercalation of excess fluoride ions to the perovskite layer, leading to a reversible capacity of 200 mA h/g. The additional fluoride-ion intercalation leads to the formation of O-O bond in the structure for charge compensation (i.e., anion redox). These results highlight the layered perovskite oxyfluorides as a new class of active materials for the construction of high-performance FIBs.

Artifactual atomic displacements on surfaces using annular dark-field images with image simulation.

We investigated artifactual atomic displacements on a Pt (111) surface using annular dark-field (ADF) scanning transmission electron microscopy (STEM) images under ideal conditions with multi-slice image simulation. Pt atomic columns on the surface exhibited artifact displacement. The bright spots shifted slightly toward the interior of the crystal, indicating that ADF imaging underestimates atomic distance measurements on the crystal surface. Multiple peak fitting is an effective method for determining the positions of bright spots and obtaining more accurate atomic positions while reducing the impact of surface-related artifacts. This is important for the measurement of interatomic distances on crystal surfaces, particularly for catalyst particles.

Strongly Enhanced Polarization in a Ferroelectric Crystal by Conduction-Proton Flow.

Ion conductors comprising noncentrosymmetric frameworks have emerged as new functional materials. However, strongly correlated polarity functionality and ion transport have not been achieved. Herein, we report a ferroelectric proton conductor, K2MnN(CN)4·H2O (1·H2O), exhibiting the strong correlation between its polar skeleton and conductive ions that generate anomalous ferroelectricity via the proton-bias phenomenon. The application of an electric field of ±1 kV/cm (0.1 Hz) on 1·H2O at 298 K produced the ferroelectricity (polarization = 1.5 × 104 µC/cm2), which was enhanced by the ferroelectric-skeleton-trapped conductive protons. Furthermore, the strong polarity-proton transport coupling of 1·H2O induced a proton-rectification-like directional ion-conductive behavior that could be adjusted by the magnitude and direction of DC electric fields. Moreover, 1·H2O exhibited reversible polarity switching between the polar 1·H2O and its dehydrated form, 1, with a centrosymmetric structure comprising an order-disorder-type transition of the nitrido-bridged chains.

Applications of electron microscopic observations to electrochemistry in liquid electrolytes for batteries.

Herein, we review notable points from observations of electrochemical reactions in a liquid electrolyte by liquid-phase electron microscopy. In situ microscopic observations of electrochemical reactions are urgently required, particularly to solve various battery issues. Battery performance is evaluated by various electrochemical measurements of bulk samples. However, it is necessary to understand the physical/chemical phenomena occurring in batteries to elucidate the reaction mechanisms. Thus, in situ microscopic observation is effective for understanding the reactions that occur in batteries. Herein, we focus on two methods, of the liquid phase (scanning) transmission electron microscopy and liquid phase scanning electron microscopy, and summarize the advantages and disadvantages of both methods.

Mechanisms of point defect formation and ionic conduction in divalent cation-doped lanthanum oxybromide: first-principles and experimental study.

The ionic conduction mechanism in M2+-doped (M: Mg, Ca, Zn, and Sr) lanthanum oxybromide (LaOBr) was investigated theoretically and experimentally. Formation energy calculations of point defects revealed that Br- ion vacancies and substitutional M2+ ions were the major point defects in M2+-doped LaOBr, while Br- ion vacancies and antisite O2- ions at Br sites were the major defect types in pure LaOBr. In the relaxed point defect models, doped Mg2+ and Zn2+ ions were displaced from the initial positions of the La3+ ions, and this was experimentally supported by crystal structural analysis. These significant atomic shifts were probably due to the strong interactions between Br- and the dopant ions. First-principles calculations and experimental analyses using X-ray photoelectron spectroscopy and X-ray absorption fine-structure spectroscopy also suggested the existence of strong interactions. The migration energy of Br- ions was calculated to be 0.53 eV, while the migration energy of O2- ions was 0.92 eV, implying that Br- ion migration via a vacancy system was more probable than O2- ion migration. The calculated association energies between MLa and VBr were 0.4-0.6 eV, suggesting that the association needed to be disrupted for Br- ion conduction. The sum of the association and migration energies was comparable to the experimental association energies of M2+-doped LaOBr.

Potassium-rich antiperovskites K3HTe and K3FTe and their structural relation to lithium and sodium counterparts.

Unlike perovskite oxides, antiperovskites M3HCh and M3FCh (M = Li, Na; Ch = S, Se, Te) mostly retain their ideal cubic structure over a wide range of compositions owing to anionic size flexibility and low-energy phonon modes that promote their ionic conductivity. In this study, we show the synthesis of potassium-based antiperovskites K3HTe and K3FTe and discuss the structural features in comparison with lithium and sodium analogues. It is shown experimentally and theoretically that both compounds maintain a cubic symmetry and can be prepared at ambient pressure, in contrast to most of the reported M3HCh and M3FCh which require high pressure synthesis. A systematic comparison of a series of cubic M3HTe and M3FTe (M = Li, Na, K) revealed that telluride anions contract in the order of K, Na, Li, with a pronounced contraction in the Li system. This result can be understood in terms of the difference in charge density of alkali metal ions as well as the size flexibility of Ch anions, contributing to the stability of the cubic symmetry.

A new family of anti-perovskite oxyhydrides with tetrahedral GaO4 polyanions.

New solid compounds A3-xGaO4H1-y (A = Sr, Ba; x ∼0.15, y ∼0.3), which are the first oxyhydrides containing gallium ions, have been synthesized by high-pressure synthesis. Powder X-ray and neutron diffraction experiments revealed that the series adopts an anti-perovskite structure consisting of hydride-anion-centered HA6 octahedra with tetrahedral GaO4 polyanions, wherein the A- and H-sites show partial defect. Formation energy calculations from the raw materials support that stoichiometric Ba3GaO4H is thermodynamically stable with a wide band gap. Annealing the A = Ba powder under flowing Ar and O2 gas suggests topochemical H- desorption and O2-/H- exchange reactions, respectively.

Facilitating ab initio configurational sampling of multicomponent solids using an on-lattice neural network model and active learning.

We propose a scheme for ab initio configurational sampling in multicomponent crystalline solids using Behler-Parinello type neural network potentials (NNPs) in an unconventional way: the NNPs are trained to predict the energies of relaxed structures from the perfect lattice with configurational disorder instead of the usual way of training to predict energies as functions of continuous atom coordinates. An active learning scheme is employed to obtain a training set containing configurations of thermodynamic relevance. This enables bypassing of the structural relaxation procedure that is necessary when applying conventional NNP approaches to the lattice configuration problem. The idea is demonstrated on the calculation of the temperature dependence of the degree of A/B site inversion in three spinel oxides, MgAl2O4, ZnAl2O4, and MgGa2O4. The present scheme may serve as an alternative to cluster expansion for "difficult" systems, e.g., complex bulk or interface systems with many components and sublattices that are relevant to many technological applications today.

Atomic-Scale Observations of Oxygen Release Degradation in Sulfide-Based All-Solid-State Batteries with Layered Oxide Cathodes.

All-solid-state batteries exhibit considerable potential for applications in electric vehicles. Understanding and controlling the oxygen release from the layered cathode active material are essential in achieving long-term operation of all-solid-state batteries because the oxygen release degrades the cathode material and the solid electrolyte, triggering capacity degradation. In this study, we verified the specific interface where the oxygen release is accelerated by atomic-scale scanning transmission electron microscopy and electron energy loss spectroscopy analyses. Oxygen release is suppressed at the interface where the LiNbO3 coating layer is sufficiently formed. Decomposition products on the solid electrolyte and the antisite defect layers on the cathode surface are formed by oxygen release at the interface where the Li2S-P2S5 solid electrolyte and Li(Ni1/3Mn1/3Ni1/3)O2 cathode are in direct contact. These irreversible passivation layers lead to capacity degradation. In addition, we found that exfoliation of the LiNbO3 coating from the cathode not only physically breaks the Li conduction path but also results in oxygen release and the deterioration of the cathode. These atomic-scale insights can further advance the development of all-solid-state batteries by suppressing oxygen release.

Anion Redox in an Amorphous Titanium Polysulfide.

Amorphous transition-metal polysulfides are promising positive electrode materials for next-generation rechargeable lithium-ion batteries because of their high theoretical capacities. In this study, sulfur anion redox during lithiation of amorphous TiS4 (a-TiS4) was investigated by using experimental and theoretical methods. It was found that a-TiS4 has a variety of sulfur valence states such as S2-, S-, and Sδ-. The S2- species became the main component in the Li4TiS4 composition, indicating that sulfur is a redox-active element up to this composition. The simulated a-TiS4 structure changed gradually by lithium accommodation to form a-Li4TiS4: S-S bonds in the disulfide units and polysulfide chains were broken. Bader charge analysis suggested that the average S valency decreased drastically. Moreover, deep lithiation of a-TiS4 provided a conversion reaction to metallic Ti and Li2S, with a high practical capacity of ∼1000 mAh g-1 when a lower cutoff voltage was applied.

Lithium Lanthanum Titanate Single Crystals: Dependence of Lithium-Ion Conductivity on Crystal Domain Orientation.

Lithium lanthanum titanate La2/3-xLi3xTiO3 (LLTO) has the potential to exhibit the highest Li-ion conductivity among oxide-based electrolytes because of the fast Li-ion diffusion derived from its crystal structure. Herein, bulk Li-ion conductivity of up to σbulk = 4.0 × 10-3 S/cm at 300 K, which is approximately three to four times higher than that of LLTO polycrystals, was demonstrated using LLTO single crystals, and their dependence on crystal domain orientation was examined. A change in the activation energy, which was previously obscured because of random crystal orientation, was observed at approximately 260 K. Furthermore, electron microscopy analysis indicated that the ionic conductivity of LLTOs remained higher because the region with the highest ionic conductivity was tilted away from the ideal conduction orientation. The results reported herein provide the highest conductivity in LLTO and important insights into their crystal structures, enabling higher conductivity in novel oxide-based electrolyte design.

Reliable electrochemical setup for in situ observations with an atmospheric SEM.

A novel setup for the in situ observation of electrochemical reactions in liquids through atmospheric scanning electron microscopy (SEM) is presented. The proposed liquid-phase electrochemical SEM system consists of a working electrode (WE) on an electrochemical chip and other two electrodes inserted into a liquid electrolyte; electrochemical reactions occurring at the WE are controlled precisely with an external potentiostat/galvanostat connected to the three electrodes. Copper deposition from a CuSO4 aqueous solution was conducted onto the WE, and simultaneous acquisition of nanoscale images and reliable electrochemical data was achieved with the proposed setup.

Lone-Pair-Induced Intra- and Interlayer Polarizations in Sillén-Aurivillius Layered Perovskite Bi4NbO8Br.

Sillén-Aurivillius layered perovskite oxyhalides Bi4MO8X (M = Nb, Ta; X = Cl, Br) are of great interest because of their potential as lead-free ferroelectrics in addition to their function as visible-light-responsive photocatalysts. In this work, we revisited the crystal structure of Bi4NbO8Br (space group: P21cn), revealing that the intralayer polarization is not based on the reported NbO6 octahedral tilting but is derived from the stereochemically active Bi3+ lone pair electrons (LPEs) and the octahedral off-centering of Nb5+ cations. The revised structure (space group: Ic) has additional interlayer polarizations (calculated: 0.6 µC/cm2), in agreement with recent experiments on Bi4NbO8Br. The occurrence of polarization due to stereochemically active LPEs and Nb-site off-centering is similar to Aurivillius-type ferroelectrics (e.g., Bi2WO6), with comparable spontaneous polarizations in the in-plane direction (calculated: 43.5 µC/cm2). This, together with the out-of-plane polarization, indicates that Sillén-Aurivillius compounds have great potential as ferroelectric materials.

Design and fabrication of an electrochemical chip for liquid-phase transmission electron microscopy.

Liquid-phase transmission electron microscopy (LP-TEM) can be used with an electrochemical chip (e-chip) to observe electrochemical reactions in a liquid in situ. The design of electrodes on an e-chip fabricated using microelectromechanical system technology cannot be easily changed. Here, we report a newly designed e-chip and its fabrication process. Electrodes with a desired shape were fabricated with various metals via an additional step of vacuum deposition onto our e-chip with a shadow mask. For precise control of the electrochemical reactions in LP-TEM, optimization of the electrode shape and material is critical.

Atomic-Level Changes during Electrochemical Cycling of Oriented LiMn2O4 Cathodic Thin Films.

Spinel LiMn2O4 is an attractive lithium-ion battery cathode material that undergoes a complex series of structural changes during electrochemical cycling that lead to rapid capacity fading, compromising its long-term performance. To gain insights into this behavior, in this report we analyze changes in epitaxial LiMn2O4 thin films during the first few charge-discharge cycles with atomic resolution and correlate them with changes in the electrochemical properties. Impedance spectroscopy and scanning transmission electron microscopy are used to show that defect-rich LiMn2O4 surfaces contribute greatly to the increased resistivity of the battery after only a single charge. Sequences of {111} stacking faults within the films were also observed upon charging, increasing in number with further cycling. The atomic structures of these stacking faults are reported for the first time, showing that Li deintercalation is accompanied by local oxygen loss and relaxation of Mn atoms onto previously unoccupied sites. The stacking faults have a more compressed structure than the spinel matrix and impede Li-ion migration, which explains the observed increase in thin-film resistivity as the number of cycles increases. These results are used to identify key factors contributing to conductivity degradation and capacity fading in LiMn2O4 cathodes, highlighting the need to develop techniques that minimize defect formation in spinel cathodes to improve cycle performance.

Oxide-ion diffusion in brownmillerite-type Ca2AlMnO5+δ from first-principles calculations.

Oxide-ion diffusion pathways in brownmillerite oxides Ca2AlMnO5 and Ca2AlMnO5.5 are systematically investigated using first-principles calculations. These structures reversibly transform into each other by oxidation and reduction. We examine oxide-ion migration in Ca2AlMnO5 and Ca2AlMnO5.5 using the nudged elastic band method. In the reduced structure (Ca2AlMnO5), oxide-ion migration through a vacancy channel is found to have the lowest migration energy barrier, at 0.58 eV. The migration energy barrier of the second-lowest energy path, perpendicular to the vacancy channel, is found to be 0.98 eV. In the oxidized structure (Ca2AlMnO5.5), oxide-ion migration within AlO6 layers has migration energy barriers of 0.55 eV and 0.56 eV in the [100] and [001] directions, respectively. Oxide-ion migration perpendicular to the AlO6 layer has a migration energy barrier of 1.33 eV, suggesting that oxide-ion diffusion in the [010] direction is difficult even at elevated temperature. These results indicate that diffusion in the reduced phase is predominantly one-dimensional whereas it is two-dimensional in the oxidized phase.

Influence of Ag Clusters on the Electronic Structures of ß-Ga2O3 Photocatalyst Surfaces.

In order to understand the photocatalytic carbon dioxide reduction over Ag-loaded ß-Ga2O3 photocatalysts, first principles calculations based on density functional theory were performed on the surface model of a Ag cluster-adsorbed ß-Ga2O3 system. The stable adsorption structures of Ag n (n = 1 to 4) clusters on the ß-Ga2O3 (100) surface were determined. In the electronic structure analysis, the valence states of all Ag clusters mixed with the top of the O 2p valence band of Ga2O3, leading the Fermi level of Ag n /ß-Ga2O3 to shift to the bottom of the conduction band. It was also revealed that the unoccupied states of Ag n clusters overlapped with the Ga unoccupied states, and occupied electronic states of Ag clusters were formed in the band gap. These calculation results corresponded to the experimental ones obtained in our previous study, i.e., small Ag clusters had strong interaction with the Ga2O3 surface, enhancing the electron transfer between the Ag clusters and the Ga2O3 surface. That is, excited electrons toward Ag n clusters or the perimeter of Ag-Ga2O3 should be the important key to promote photocatalytic CO2 reduction.

Dehydration of Electrochemically Protonated Oxide: SrCoO2 with Square Spin Tubes.

Controlling oxygen deficiencies is essential for the development of novel chemical and physical properties such as high-Tc superconductivity and low-dimensional magnetic phenomena. Among reduction methods, topochemical reactions using metal hydrides (e.g., CaH2) are known as the most powerful method to obtain highly reduced oxides including Nd0.8Sr0.2NiO2 superconductor, though there are some limitations such as competition with oxyhydrides. Here we demonstrate that electrochemical protonation combined with thermal dehydration can yield highly reduced oxides: SrCoO2.5 thin films are converted to SrCoO2 by dehydration of HSrCoO2.5 at 350 °C. SrCoO2 forms square (or four-legged) spin tubes composed of tetrahedra, in contrast to the conventional infinite-layer structure. Detailed analyses suggest the importance of the destabilization of the SrCoO2.5 precursor by electrochemical protonation that can greatly alter reaction energy landscape and its gradual dehydration (H1-xSrCoO2.5-x/2) for the SrCoO2 formation. Given the applicability of electrochemical protonation to a variety of transition metal oxides, this simple process widens possibilities to explore novel functional oxides.