Enhancing DSSC Performance through Manipulation of the Size of ZnO Nanorods.

The synthesis of one-dimensional zinc oxide nanorod photoelectrodes through a chemical solution method and their application in dye-sensitized solar cells are described in this paper. A multiple growth approach was used to fabricate zinc oxide nanorods with varying length-to-diameter ratios, and their dye adsorption properties were characterized using ultraviolet-visible spectroscopy. The zinc oxide photoelectrodes with different length-to-diameter ratios were subsequently incorporated into dye-sensitized solar cells, and their performance and carrier lifetime were analyzed using a solar simulator, monochromatic incident photon-to-electron conversion efficiency, and electrochemical impedance spectroscopy. The highest efficiency achieved was 0.74%. The results indicate that the quality of the zinc oxide nanorods synthesized through the multiple growth approach is consistent, with the uniformity and morphology of the nanorods having the greatest impact on device efficiency.

Suppression of SnS2 Secondary Phase on Cu2ZnSnS4 Solar Cells Using Multi-Metallic Stacked Nanolayers.

In Cu2ZnSnS4 (CZTS) solar cells, it is crucial to suppress the generation of and remove the SnS2 secondary phase to improve the solar cell characteristics, as the SnS2 secondary phase affects the barrier for carrier collection and diode characteristics of the device. In this study, the nano-metallic precursor was modified to effectively suppress the generation of the SnS2 secondary phase on the surface and simultaneously improve the uniformity and quality of the thin film. The CZTS bifacial solar cells prepared via the proposed method exhibited significantly improved junction-rectifying characteristics, as the efficiency was improved to 1.59%. The proposed method to figurremove SnS2 is effective, simple, and environmentally friendly.

Location-Optoelectronic Property Correlation in ZnO:Al Thin Film by RF Magnetron Sputtering and Its Photovoltaic Application.

In this study, a radio-frequency magnetron sputter system was used to deposit Al2O3 doped ZnO (AZO) thin films at room temperature, and the soda lime glass (SLG) substrates were placed at different zones relative to the center of the sample holder under the target. The samples were then analyzed using an X-ray diffractometer, Hall-effect measurement system, UV-visible spectrophotometer, and X-ray photoelectron spectroscopy. It was found that the electrical, structural, and optical properties of AZO films strongly depend on the target racetrack. The AZO thin film grown at a location outside the racetrack not only has the most suitable figure of merit for transparent conductive films, but also retains the least residual stress, which makes it the most suitable candidate for use as a CZTSe transparent conductive layer. When applied to CZTSe solar cells, the photoelectric efficiency is 3.56%.

Enhanced omnidirectional light harvesting in dye-sensitized solar cells with periodic ZnO nanoflower photoelectrodes.

In this study, two-dimensional ZnO nanoflower photoelectrodes were prepared using a chemical solution method and applied to dye-sensitised solar cells. By growing ZnO nanoflowers with different lengths on the photoelectrodes, the effects of the ZnO nanoflowers on the omnidirectional light-harvesting and broadband of dye-sensitised solar cells were investigated. According to the field emission scanning electron microscope and UV-Vis-NIR measurements of the prepared ZnO nanoflowers at different lengths, it can be determined that the amount of dye adsorption and degree of light scattering are affected by the lengths of the nanoflowers. A finite difference time-domain simulation was used to verify whether the degree of light scattering was affected by the lengths of the ZnO nanoflowers. In addition, the prepared ZnO nanoflower photoelectrodes of different lengths were applied to dye-sensitised solar cells. The photoelectric element efficiency, carrier life cycle, and element characteristics under wide-angle measurements were investigated through electrochemical impedance spectroscopy, the monochromic incident photon-to-electronic conversion efficiency, and a solar simulator. At high angles, the difference in efficiency of multi-directional incident light was reduced from 46% to 12%, which effectively improved the capturing characteristics of the multi-directional incident light during light scattering.

Enhanced omnidirectional and weatherability of Cu2ZnSnSe4 solar cells with ZnO functional nanorod arrays.

This paper presents the use of nanorods of different sizes, deposited from a chemical solution, as an antireflection layer in copper-zinc-tin selenide (CZTSe) solar cells. With the aid of the nanorods, the surface reflection of the CZTSe solar cells was reduced from 7.76% to 2.97%, and a cell efficiency of 14% was obtained as a result. Omni-directional anti-reflection was verified by the angle-dependent reflection measurements. The nanorod arrays also provided the CZTSe solar cells with a hydrophobic surface, allowing it to exhibit high resistance against humidity during weatherability tests. This shows that the surface passivation brought by the nanorod layer at the surface could effectively extend the lifetime of the CZTSe solar cells. The rate of efficiency decay of the CZTSe solar cells was reduced by 46.85% from that of the device without a nanorod array at the surface, indicating that this surface layer not only provided effective resistance against reflection at the device surface, but also served as a passivation layer and humidity-resistant surface-protection layer.

Cu2ZnSnSe4 Thin Film Solar Cell with Depth Gradient Composition Prepared by Selenization of Sputtered Novel Precursors.

In this study, we proposed a new method for the synthesis of the target material used in a two stage process for preparation of a high quality CZTSe thin film. The target material consisting of a mixture of CuxSe and ZnxSn1-x alloy was synthesized, providing a quality CZTSe precursor layer for highly efficient CZTSe thin film solar cells. The CZTSe thin film can be obtained by annealing the precursor layers through a 30 min selenization process under a selenium atmosphere at 550 °C. The CZTSe thin films prepared by using the new precursor thin film were investigated and characterized using X-ray diffraction, Raman scattering, and photoluminescence spectroscopy. It was found that diffusion of Sn occurred and formed the CTSe phase and CuxSe phase in the resultant CZTSe thin film. By selective area electron diffraction transmission electron microscopy images, the crystallinity of the CZTSe thin film was verified to be single crystal. By secondary ion mass spectroscopy measurements, it was confirmed that a double-gradient band gap profile across the CZTSe absorber layer was successfully achieved. The CZTSe solar cell with the CZTSe absorber layer consisting of the precursor stack exhibited a high efficiency of 5.46%, high short circuit current (JSC) of 37.47 mA/cm2, open circuit voltage (VOC) of 0.31 V, and fill factor (F.F.) of 47%, at a device area of 0.28 cm2. No crossover of the light and dark current-voltage (I-V) curves of the CZTSe solar cell was observed, and also, no red kink was observed under red light illumination, indicating a low defect concentration in the CZTSe absorber layer. Shunt leakage current with a characteristic metal/CZTSe/metal leakage current model was observed by temperature-dependent I-V curves, which led to the discovery of metal incursion through the CdS buffer layer on the CZTSe absorber layer. This leakage current, also known as space charge-limited current, grew larger as the measurement temperature increased and completely overwhelmed the diode current at a measurement temperature of 200 °C. This is due to interlayer diffusion of metal that increases the shunt leakage current and decreases the efficiency of the CZTSe thin film solar cells.

Crystalline Engineering Toward Large-Scale High-Efficiency Printable Cu(In,Ga)Se2 Thin Film Solar Cells on Flexible Substrate by Femtosecond Laser Annealing Process.

Ink-printing method emerges as a viable way for manufacturing large-scale flexible Cu(In,Ga)Se2 (CIGS) thin film photovoltaic (TFPV) devices owing to its potential for the rapid process, mass production, and low-cost nonvacuum device fabrication. Here, we brought the femtosecond laser annealing (fs-LA) process into the ink-printing CIGS thin film preparation. The effects of fs-LA treatment on the structural and optoelectronic properties of the ink-printing CIGS thin films were systematically investigated. It was observed that, while the film surface morphology remained essentially unchanged under superheating, the quality of crystallinity was significantly enhanced after the fs-LA treatment. Moreover, a better stoichiometric composition was achieved with an optimized laser scanning rate of the laser beam, presumably due to the much reduced indium segregation phenomena, which is believed to be beneficial in decreasing the defect states of InSe, VSe, and InCu. Consequently, the shunt leakage current and recombination centers were both greatly decreased, resulting in a near 20% enhancement in photovoltaic conversion efficiency.

Realizing omnidirectional light harvesting by employing hierarchical architecture for dye sensitized solar cells.

To improve the omnidirectional light-harvesting in dye-sensitized solar cells (DSSCs), here we present a dandelion-like structure composed of ZnO hemispherical shells and nanorods. Uniformly distributed hemispherical shells effectively suppress the reflection over the broadband region at incident angles up to 60°, greatly improving the optical absorption of the DSSCs. In addition, modulating the length of the ZnO nanorods controls the omnidirectional characteristics of DSSCs. This phenomenon is attributed to the degree of periodicity of the ZnO dandelion-like structures. Cells with shorter rods exhibit a high degree of periodicity, thus the conversion efficiencies of the cells show specific angle-independent features. On the other hand, the cells with longer lengths reveal angle-dependent photovoltaic performance. Along with the simulation, the cells with dandelion-like ZnO structures can couple incident photons efficiently to achieve excellent broadband and omnidirectional light-harvesting performances experimentally, and the DSSCs enhanced the conversion efficiency by 48% at large incident angles. All these findings not only provide further insight into the light-trapping mechanism in these complex three-dimensional nanostructures but also offer efficient omnidirectional and broadband nanostructured photovoltaics for advanced applications.

Efficiency Enhancement of Dye-Sensitized Solar Cells' Performance with ZnO Nanorods Grown by Low-Temperature Hydrothermal Reaction.

In this study, aligned zinc oxide (ZnO) nanorods (NRs) with various lengths (1.5-5 µm) were deposited on ZnO:Al (AZO)-coated glass substrates by using a solution phase deposition method; these NRs were prepared for application as working electrodes to increase the photovoltaic conversion efficiency of solar cells. The results were observed in detail by using X-ray diffraction, field-emission scanning electron microscopy, UV-visible spectrophotometry, electrochemical impedance spectroscopy, incident photo-to-current conversion efficiency, and solar simulation. The results indicated that when the lengths of the ZnO NRs increased, the adsorption of D-719 dyes through the ZnO NRs increased along with enhancing the short-circuit photocurrent and open-circuit voltage of the cell. An optimal power conversion efficiency of 0.64% was obtained in a dye-sensitized solar cell (DSSC) containing the ZnO NR with a length of 5 µm. The objective of this study was to facilitate the development of a ZnO-based DSSC.

Interfacial atomic structure analysis at sub-angstrom resolution using aberration-corrected STEM.

The atomic structure of a SiGe/Si epitaxial interface grown via molecular beam epitaxy on a single crystal silicon substrate was investigated using an aberration-corrected scanning transmittance electron microscope equipped with a high-angle annular dark-field detector and an energy-dispersive spectrometer. The accuracy required for compensation of the various residual aberration coefficients to achieve sub-angstrom resolution with the electron optics system was also evaluated. It was found that the interfacial layer was composed of a silicon single crystal, connected coherently to epitaxial SiGe nanolaminates. In addition, the distance between the dumbbell structures of the Si and Ge atoms was approximately 0.136 nm at the SiGe/Si interface in the [110] orientation. The corresponding fast Fourier transform exhibited a sub-angstrom scale point resolution of 0.78 Å. Furthermore, the relative positions of the atoms in the chemical composition line scan signals could be directly interpreted from the corresponding incoherent high-angle annular dark-field image.

Growth and characterization of Cu(In,Ga)Se2 thin films by nanosecond and femtosecond pulsed laser deposition.

In this work, CuIn1 - x Ga x Se2 (CIGS) thin films were prepared by nanosecond (ns)- and femtosecond (fs)-pulsed laser deposition (PLD) processes. Different film growth mechanisms were discussed in perspective of the laser-produced plasmas and crystal structures. The fs-PLD has successfully improved the inherent flaws, Cu2 - x Se, and air voids ubiquitously observed in ns-PLD-derived CIGS thin films. Moreover, the prominent antireflection and excellent crystalline structures were obtained in the fs-PLD-derived CIGS thin films. The absorption spectra suggest the divergence in energy levels of radiative defects brought by the inhomogeneous distribution of elements in the fs-PLD CIGS, which has also been supported by comparing photoluminescence (PL) spectra of ns- and fs-PLD CIGS thin films at 15 K. Finally, the superior carrier transport properties in fs-PLD CIGS were confirmed by fs pump-probe spectroscopy and four-probe measurements. The present results indicate a promising way for preparing high-quality CIGS thin films via fs-PLD.

Improved dye-sensitized solar cell with a ZnO nanotree photoanode by hydrothermal method.

This study investigated the influence of ZnO nanostructures on dye adsorption to increase the photovoltaic conversion efficiency of solar cells. ZnO nanostructures were grown in both tree-like and nanorod (NR) arrays on an AZO/FTO film structure by using a hydrothermal method. The results were observed in detail using X-ray diffraction, field-emission scanning electron microscopy (FE-SEM), UV-visible spectrophotometry, electrochemical impedance spectroscopy, and solar simulation. The selective growth of tree-like ZnO was found to exhibit higher dye adsorption loading and conversion efficiency than ZnO NRs. The multiple 'branches' of 'tree-like nanostructures' increases the surface area for higher light harvesting and dye loading while reducing charge recombination. These improvements result in a 15% enhancement in power conversion. The objective of this study is to facilitate the development of a ZnO-based dye-sensitized solar cell.

Flexible-textured polydimethylsiloxane antireflection structure for enhancing omnidirectional photovoltaic performance of Cu(In,Ga)Se2 solar cells.

Because of the Sun's movement across the sky, broadband and omnidirectional light harvesting is a major development in photovoltaic technology. This study reports the fabrication and characterization of flexible-textured polydimethylsiloxane (PDMS) film on Cu(In,Ga)Se2 (CIGS) solar cells, which is one of the simplest and cheapest peel-off processes for fabricating a three-dimensional structure. A cell containing a textured PDMS film enhanced the short-circuit current density from 22.12 to 23.93 mA/cm2 in a simulated one-sun scenario. The omnidirectional antireflection of CIGS solar cells containing various PDMS films is also investigated. This study uses an angle-resolved reflectance spectroscope to investigate the omnidirectional and broadband optical properties of the proposed PDMS film. This improvement in light harvesting is attributable to the scattering of the PDMS film and the gradual refractive index profile between the PDMS microstructures and air. The flexible-textured PDMS film is suitable for creating an antireflective coating for a diverse range of photovoltaic devices.

Stability scheme of ZnO-thin film resistive switching memory: influence of defects by controllable oxygen pressure ratio.

We report a stability scheme of resistive switching devices based on ZnO films deposited by radio frequency (RF) sputtering process at different oxygen pressure ratios. I-V measurements and statistical results indicate that the operating stability of ZnO resistive random access memory (ReRAM) devices is highly dependent on oxygen conditions. Data indicates that the ZnO film ReRAM device fabricated at 10% O2 pressure ratio exhibits the best performance. Transmission electron microscopy (TEM) and X-ray diffraction (XRD) of ZnO at different O2 pressure ratios were investigated to reflect influence of structure to the stable switching behaviors. In addition, PL and XPS results were measured to investigate the different charge states triggered in ZnO by oxygen vacancies, which affect the stability of the switching behavior.

Non-antireflective scheme for efficiency enhancement of Cu(In,Ga)Se2 nanotip array solar cells.

We present systematic works in characterization of CIGS nanotip arrays (CIGS NTRs). CIGS NTRs are obtained by a one-step ion-milling process by a direct-sputtering process of CIGS thin films (CIGS TF) without a postselenization process. At the surface of CIGS NTRs, a region extending to 100 nm in depth with a lower copper concentration compared to that of CIGS TF has been discovered. After KCN washing, removal of secondary phases can be achieved and a layer with abundant copper vacancy (V(Cu)) was left. Such compositional changes can be a benefit for a CIGS solar cell by promoting formation of Cd-occupied Cu sites (Cd(Cu)) at the CdS/CIGS interface and creates a type-inversion layer to enhance interface passivation and carrier extraction. The raised V(Cu) concentration and enhanced Cd diffusion in CIGS NTRs have been verified by energy dispersive spectrometry. Strengthened adhesion of Al:ZnO (AZO) thin film on CIGS NTRs capped with CdS has also been observed in SEM images and can explain the suppressed series resistance of the device with CIGS NTRs. Those improvements in electrical characteristics are the main factors for efficiency enhancement rather than antireflection.

Enhancement of light output power of GaN-based light-emitting diodes with photonic quasi-crystal patterned on p-GaN surface and n-side sidewall roughing.

In this paper, GaN-based light-emitting diodes (LEDs) with photonic quasi-crystal (PQC) structure on p-GaN surface and n-side roughing by nano-imprint lithography are fabricated and investigated. At an injection current of 20 mA, the LED with PQC structure on p-GaN surface and n-side roughing increased the light output power of the InGaN/GaN multiple quantum well LEDs by a factor of 1.42, and the wall-plug efficiency is 26% higher than the conventional GaN-based LED type. After 500-h life test (55°C/50 mA), it was found that the normalized output power of GaN-based LED with PQC structure on p-GaN surface and n-side roughing only decreased by 6%. These results offer promising potential to enhance the light output powers of commercial light-emitting devices using the technique of nano-imprint lithography.

Dandelion-shaped nanostructures for enhancing omnidirectional photovoltaic performance.

Broadband and omnidirectional light harvesting is important in photovoltaic technology because of its wide spectral range of radiation and the sun's movement. This study reports the fabrication and characterization of zinc oxide (ZnO) dandelions on Cu(In,Ga)Se2 (CIGS) solar cells. The fabrication of dandelions involves the combination of self-assembled polystyrene (PS) nanospheres and the hydrothermal method, which is one of the simplest and cheapest methods of fabricating a three-dimensional, closely packed periodic structure. This study also investigates the optimization on dimension of the PS nanospheres using the rigorous coupled-wave analysis (RCWA) method. This study uses an angle-resolved reflectance spectroscope and a homemade rotatable photo I-V measurement to investigate the omnidirectional and broadband antireflections of the proposed dandelion structure. Under a simulated one-sun condition and a light incident angle of up to 60°, cells with ZnO dandelions arrays enhanced the short-circuit current density by 31.87%. Consequently, ZnO dandelions are suitable for creating an omnidirectionally antireflective coating for photovoltaic devices.

Enhanced broadband and omnidirectional performance of Cu(In,Ga)Se2 solar cells with ZnO functional nanotree arrays.

An effective approach is demonstrated for enhancing photoelectric conversion of Cu(In,Ga)Se2 (CIGS) solar cells with three-dimensional ZnO nanotree arrays. Under a simulated one-sun condition, cells with ZnO nanotree arrays enhance the short-circuit current density by 10.62%. The omnidirectional anti-reflection of CIGS solar cells with various ZnO nanostructures is also investigated. The solar-spectrum weighted reflectance is approximately less than 5% for incident angles of up to 60° and for the wavelengths primarily from 400 nm to 1000 nm. This enhancement in light harvesting is attributable to the gradual refractive index profile between the ZnO nanostructures and air.

Observation of unusual optical transitions in thin-film Cu(In,Ga)Se2 solar cells.

In this paper, we examine photoluminescence spectra of Cu(In,Ga)Se(2) (CIGS) via temperature-dependent and power-dependent photoluminescence (PL). Donor-acceptor pair (DAP) transition, near-band-edge transition were identified by their activation energies. S-shaped displacement of peak position was observed and was attributed to carrier confinement caused by potential fluctuation. This coincides well with the obtained activation energy at low temperature. We also present a model for transition from V(Se) to V(In) and to V(Cu) which illustrates competing mechanisms between DAPs recombinations.

Study of InN epitaxial films and nanorods grown on GaN template by RF-MOMBE.

This paper reports on high-quality InN materials prepared on a GaN template using radio-frequency metalorganic molecular beam epitaxy. We also discuss the structural and electro-optical properties of InN nanorods/films. The X-ray diffraction peaks of InN(0002) and InN(0004) were identified from their spectra, indicating that the (0001)-oriented hexagonal InN was epitaxially grown on the GaN template. Scanning electron microscopic images of the surface morphology revealed a two-dimensional growth at a rate of approximately 0.85 µm/h. Cross-sectional transmission electron microscopy images identified a sharp InN/GaN interface and a clear epitaxial orientation relationship of [0001]InN // [0001]GaN and ( 2¯110)InN // ( 2¯110)GaN. The optical properties of wurtzite InN nanorods were determined according to the photoluminescence, revealing a band gap of 0.77 eV.