Study and Optimization of a Micro-Structured Waveguiding and Fluorescent Sol-Gel Architecture.

Channel waveguides with diffraction gratings at their input and output for light injection and extraction, respectively, constitute the key components for applications in integrated optics and photonics. Here, we report for the first time on such fluorescent micro-structured architecture entirely elaborated on glass by sol-gel processing. This architecture particularly takes advantage of a high-refractive index and transparent titanium oxide-based, sol-gel photoresist that can be imprinted through a single photolithography step. This resist enabled us to photo-imprint the input and output gratings on a photo-imprinted channel waveguide doped with a ruthenium complex fluorophore (Rudpp). In this paper, the elaboration conditions and optical characterizations of derived architectures are presented and discussed with respect to optical simulations. We firstly show how the optimization of a two-step deposition/insolation sol-gel procedure leads to reproducible and uniform grating/waveguide architectures elaborated on rather large dimensions. Then, we show how this reproducibility and uniformity govern the reliability of fluorescence measurements in waveguiding configuration. These measurements demonstrate that: (i) our sol-gel architecture is well adapted to the efficient channel-waveguide/diffraction grating coupling at the Rudpp excitation and emission wavelengths; (ii) it enables an efficient propagation of the emission signal in the core of the waveguide allowing its photo-detection after extraction through the output grating; and (iii) it is affected by very reduced parasitic mechanisms, such as propagation losses and photobleaching features. This work constitutes a promising preliminary step toward the integration of our architecture in a microfluidic platform for further fluorescence measurements in liquid medium and waveguiding configuration.

Nanostructuration of YAG:Ce Coatings by ZnO Nanowires: A Smart Way to Enhance Light Extraction Efficiency.

In this study, we report on the enhancement of the light extraction efficiency of sol-gel-derived Y3Al5O12:Ce3+ (YAG:Ce) coatings using ZnO nanowire (NW) arrays. The ZnO NWs were grown by hydrothermal synthesis from a ZnO seed layer directly deposited on a YAG:Ce coating. Highly dense and vertically aligned ZnO NW arrays were evidenced on the top of the YAG:Ce coating by electron microscopy. A photoluminescence study showed that this original design leads to a different angular distribution of light together with an increase in emission efficiency of the YAG:Ce coating upon blue excitation, up to 60% more efficient compared to a non-structured YAG:Ce coating (without NWs). These improvements are ascribed to multi-scattering events for photons within the structure, allowing them to escape from the phosphor layer by taking optical paths different from those of the non-structured coating. This strategy of light extraction enhancement appears to be very promising, since it uses soft chemical processes and cheap ZnO NWs and is applicable to any sol-gel-derived luminescent coating.

Setting Up and Assessing a New Micro-Structured Waveguiding Fluorescent Architecture on Glass Entirely Elaborated by Sol-Gel Processing.

Channel waveguides with diffraction gratings at their input and output for light injection and extraction, respectively, are extensively exploited for optical and photonic applications. In this paper, we report for the first time on such an architecture on glass entirely elaborated by sol-gel processing using a titanium-oxide-based photoresist that can be imprinted through a single photolithography step. This work is more particularly focused on a fluorescent architecture including channel waveguides doped with a ruthenium-complex fluorophore (tris(4,7-diphenyl-1,10-phenanthroline)ruthenium(II), Rudpp). The study demonstrates that this original sol-gel micro-structured architecture is well adapted to efficient channel waveguide/diffraction grating coupling and propagation of the fluorescence excitation and emission signals in the core of the channel waveguide. It demonstrates, in particular, a relatively large tolerance of several degrees in the angular injection fiber positioning and an important axial and vertical fiber spatial positioning tolerance of more than 100 µm at the Rudpp emission wavelength. The measurements also indicate that, in the conditions tested in this work, a Rudpp concentration of around 0.1 mM and a channel waveguide length of 2 to 5 mm offer the best trade-off in terms of excitation signal propagation and emission signal detection. This work constitutes a promising preliminary step toward the integration of our architecture into a microfluidic platform for fluorescence measurement in a liquid medium and waveguiding configuration.

Mechanical and in vitro testing of aerosol-gel deposited titania coatings for biocompatible applications.

The biocompatible properties of sol-gel litania have increased the interest in the mechanical properties of this material in the form of functional coatings for prosthetic applications. In the present work. titania coatings with thicknesses of 1 microm have been prepared using the aerosol gel process. The main objective has been to evaluate the mechanical properties of the coatings and to prove their in-vitro biocompatibility. For this purpose, the hardness and Young's modulus of the coatings were measured by nanoindentation with loads in the 6-30 mN range. A continuous increase of these magnitudes was observed for the coatings treated at increasing sintering temperatures (150-800 degrees C). The hardness and the Young's modulus ranged between 15.8-19.5 GPa and 142-186 GPa, respectively. This behaviour has been confirmed by measurements of the plastic energy of deformation in 10 mN full loading unloading tests and by determination of the mean indentation creep under 30 mN loads. The films were additionally characterised by XRD. FTIR and ellipsometry to study the chemical and structural changes produced by sintering. Biocompatibility tests are very conclusive. Cells seeded on aerosol-gel titania coatings grow while adhered onto the surface. These coatings are thus of potential interest for the enhancement of the properties of prosthetic TiAlV alloys.