Trace explosives sampling for security applications (TESSA) study: Evaluation of procedures and methodology for contact sampling efficiency.

The detection of trace amounts of explosive materials is critical to the security at mass transit centers (e.g., airports and railway stations). In a typical screening process, a trap is used to probe a surface of interest to collect and transfer particulate residue to a detector for analysis. The collection of residues from the surface being probed is widely viewed as the limiting step in this process. A multi-institutional study was performed to establish a methodology for the evaluation of sampling media collection efficiencies. Dry deposited residues of 1,3,5-trinitroperhydro-1,3,5-triazine (RDX), C-4 (an RDX-based explosive), and pentaerythritol tetranitrate (PETN) were harvested from acrylonitrile butadiene styrene (ABS) plastic, ballistic nylon (NYL), and uncoated aluminum surfaces using muslin, Texwipe cotton, and stainless-steel mesh traps. Transfer and collection efficiencies of the sample media were calculated based on liquid chromatography-mass spectrometry analysis. Dry transfer efficiencies (DTE%) to all tested surfaces were greater than 75%, with transfer to ABS plastic being the lowest. Collection efficiency (CE%) varied significantly across the traps and the surfaces, yet some conclusions can be drawn; nylon had the lowest CE% for all cases (∼10%), and the stainless steel mesh had the lowest CE% for the evaluated traps (∼20%). Though the testing parameters have been standardized among the participants to establish a framework for an independent comparison of contact sampling media and surfaces, substantial variations in the DTE% and the CE% were observed, suggesting that other variables can affect contact sampling.

Polymorphic Phase Control of RDX-Based Explosives.

The polymorphic phase of 1,3,5-trinitro-1,3,5-triazine (RDX) was examined as a function of mass loading, solvent, and sample deposition technique. When RDX was deposited at a high mass loading, the vibrational modes in the obtained Raman spectra were indicative of concomitant polymorphism as both the α-RDX and ß-RDX phases were present. At low mass loadings, only ß-RDX was observed regardless of solvent when using the drop cast crystallization method. However, α-RDX (the thermodynamically stable polymorphic phase observed with visible quantities of the explosive) was observed when RDX deposits were dry transferred. Observation of α-RDX was independent of the initial mass loading or the initial deposition solvent when using the dry transfer methodology. These data indicate that the use of the dry transfer preparation method can be used to successfully prepare RDX-based test articles with the α-RDX phase regardless of the solvent used to initially dissolve the RDX, the initial deposition technique, or the mass loading.

Characterizing the gas phase ion chemistry of an ion trap mobility spectrometry based explosive trace detector using a tandem mass spectrometer.

A commercial-off-the-shelf (COTS) ion trap mobility spectrometry (ITMS) based explosive trace detector (ETD) has been interfaced to a triple quadrupole mass spectrometer (MS/MS) for the purpose of characterizing the gas phase ion chemistry intrinsic to the ITMS instrument. The overall objective of the research is to develop a fundamental understanding of the gas phase ionization processes in the ITMS based ETD to facilitate the advancement of its operational effectiveness as well as guide the development of next generation ETDs. Product ion masses, daughter ion masses, and reduced mobility values measured by the ITMS/MS/MS configuration for a suite of nitro, nitrate, and peroxide containing explosives are reported. Molecular formulas, molecular structures, and ionization pathways for the various product ions are inferred using the mass and mobility data in conjunction with density functional theory. The predominant product ions are identified as follows: [TNT-H](-) for trinitrotoluene (TNT), [RDX+Cl](-) for cyclo-1,3,5-trimethylene-2,4,6-trinitramine (RDX), [NO(3)](-) for ethylene glycol dinitrate (EGDN), [NG+NO(3)](-) for nitroglycerine (NG), [PETN+NO(3)](-) for pentaerythritol tetranitrate (PETN), [HNO(3)+NO(3)](-) for ammonium nitrate (NH(4)NO(3)), [HMTD-NC(3)H(6)O(3)+H+Cl](-) for hexamethylene triperoxide diamine (HMTD), and [(CH(3))(2)CNH(2)](+) for triacetone triperoxide (TATP). The predominant ionization pathways for the formation of the various product ions are determined to include proton abstraction, ion-molecule attachment, autoionization, first-order and multi-order thermolysis, and nucleophilic substitution. The ion trapping scheme in the reaction region of the ITMS instrument is shown to increase predominant ion intensities relative to the secondary ion intensities when compared to non-ion trap operation.

Interfacing an ion mobility spectrometry based explosive trace detector to a triple quadrupole mass spectrometer.

Hardware from a commercial-off-the-shelf (COTS) ion mobility spectrometry (IMS) based explosive trace detector (ETD) has been interfaced to an AB/SCIEX API 2000 triple quadrupole mass spectrometer. To interface the COTS IMS based ETD to the API 2000, the faraday plate of the IMS instrument and the curtain plate of the mass spectrometer were removed from their respective systems and replaced by a custom faraday plate, which was fabricated with a hole for passing the ion beam to the mass spectrometer, and a custom interface flange, which was designed to attach the IMS instrument onto the mass spectrometer. Additionally, the mass spectrometer was modified to increase the electric field strength and decrease the pressure in the differentially pumped interface, causing a decrease in the effect of collisional focusing and permitting a mobility spectrum to be measured using the mass spectrometer. The utility of the COTS-ETD/API 2000 configuration for the characterization of the gas phase ion chemistry of COTS-ETD equipment was established by obtaining mass and tandem mass spectra in the continuous ion flow and selected mobility monitoring operating modes and by obtaining mass-selected ion mobility spectra for the explosive standard 2,4,6 trinitrotoluene (TNT). This analysis confirmed that the product ion for TNT is [TNT - H](-), the predominant collision-induced dissociation pathway for [TNT- H](-) is the loss of NO and NO(2), and the reduced mobility value for [TNT - H](-) is 1.54 cm(2)V(-1) s(-1). Moreover, this analysis was attained for sample amounts of 1 ng and with a resolving power of 37. The objective of the research is to advance the operational effectiveness of COTS IMS based ETD equipment by developing a platform that can facilitate the understanding of the ion chemistry intrinsic to the equipment.

Application of inkjet printing technology to produce test materials of 1,3,5-trinitro-1,3,5 triazcyclohexane for trace explosive analysis.

The feasibility of the use of piezoelectric drop-on-demand inkjet printing to prepare test materials for trace explosive analysis is demonstrated. RDX (1,3,5-trinitro-1,3,5 triazcyclohexane) was formulated into inkjet printable solutions and jetted onto substrates suitable for calibration of the ion mobility spectrometry (IMS) instruments currently deployed worldwide for contraband screening. Gravimetric analysis, gas chromatography/mass spectrometry (GC/MS), and ultraviolet-visible (UV-vis) absorption spectroscopy were used to verify inkjet printer solution concentrations and the quantity of explosive dispensed onto test materials. Reproducibility of the inkjet printing process for mass deposition of the explosive RDX (1,3,5-trinitro-1,3,5 triazcyclohexane) was determined to be better than 2% for a single day of printing and better than 3% day-to-day.

Characterization of composition C4 explosives using time-of-flight secondary ion mass spectrometry and X-ray photoelectron spectroscopy.

The application of surface analytical techniques such as time-of-flight secondary ion mass spectrometry (ToF-SIMS) and X-ray photoelectron spectroscopy (XPS) is explored as a means of differentiating between composition C4 plastic explosives (C-4). Three different C-4 samples including U.S. military grade C-4, commercial C-4 (also from the United States), and C-4 from England (PE-4) were obtained and analyzed using both ToF-SIMS and XPS. ToF-SIMS was able to successfully discriminate between different C-4 samples with the aid of principal component analysis, a multivariate statistical analysis approach often used to reduce the dimensionality of complex data. ToF-SIMS imaging was also used to obtain information about the spatial distribution of the various additives contained within the samples. The results indicated that the samples could potentially be characterized by their 2-D chemical and morphological structure, which varied from sample to sample. XPS analysis also showed significant variation between samples, with changes in the atomic concentrations, as well as changes in the shapes of the high-resolution C 1s and O 1s spectra. These results clearly demonstrate the feasibility of utilizing both ToF-SIMS and XPS as tools for the direct characterization and differentiation of C-4 samples for forensic applications.

Characterization of high explosive particles using cluster secondary ion mass spectrometry.

The use of secondary ion mass spectrometry (SIMS) for the detection and spatially resolved analysis of individual high explosive particles is described. A C(8) (-) carbon cluster primary ion beam was used in a commercial SIMS instrument to analyze samples of high explosives dispersed as particles on silicon substrates. In comparison with monatomic primary ion bombardment, the carbon cluster primary ion beam was found to greatly enhance characteristic secondary ion signals from the explosive compounds while causing minimal beam-induced degradation. The resistance of these compounds to degradation under ion bombardment allows explosive particles to be analyzed under high primary ion dose bombardment (dynamic SIMS) conditions, facilitating the rapid acquisition of spatially resolved molecular information. The use of cluster SIMS combined with computer control of the sample stage position allows for the automated identification and counting of explosive particle distributions on silicon surfaces. This will be useful for characterizing the efficiency of transfer of particulates in trace explosive detection portal collectors and/or swipes utilized for ion mobility spectrometry applications.

Adsorption-desorption characteristics of explosive vapors investigated with microcantilevers.

Understanding the kinetics of adsorption and desorption of explosive vapors such as TNT from surfaces is important in the design of sensors. We report for the first time, the adsorption-desorption characteristics of TNT from a Si-microcantilever exposed to vapors of TNT. It was observed that TNT readily sticks to the exposed Si surface with the adsorption kinetics showing an initial exponential behavior followed by roughly linear kinetics. It was also observed that for cantilever temperatures close to room temperature, TNT desorbs spontaneously from the surface with decaying exponential kinetics. Based on the known equilibrium partial vapor pressures of TNT, the "effective" sticking coefficient for the silicon oxide surface at room temperature under the experimental conditions was calculated to be about 0.02. This information can be very useful in the design of sensors and that of vapor-delivery systems.