In vivo evaluation of a polyester and fiberglass composite intramedullary nail for femoral osteosynthesis in calves.

The objective of this study was to test a composite of polyester resin and fiberglass in the form of an intramedullary nail for osteosynthesis of femoral fractures in calves. The methodology was established based on a previous study that used a bovine femur finite element model to simulate fractures, which were then stabilized by the same nails as proposed in this study. General anesthesia was induced in six calves followed by fracture creation via an oblique incision in the middle third of the femoral diaphysis, and osteosynthesis was immediately performed by retrograde insertion of the composite nail. Locking was achieved by drilling the bone and nail without using a jig and introducing two stainless steel screws proximal and two distal to the fracture line. Five of the six calves achieved complete fracture healing after 60 days. No signs of incompatibility or toxicity of the composite were observed. However, limitations were observed during the surgery, such as difficulty in drilling the nail and trimming the remainder portion of the nail that extended beyond the length of the bone. Small fragments produced by these maneuvers were considered irritating to soft tissues during the postoperative period. It was also found that small cracks in the nail tended to propagate in the form of longitudinal fractures. In conclusion, an intramedullary nail made of polyester resin and fiberglass (a low-cost and easy-to-acquire material) was considered biocompatible and capable of allowing bone healing of femoral fractures in young cattle. However, the development of solutions for the reported limitations is crucial prior to recommending the proposed composite for clinical use.

The influence of tongue mobility on children's performance in computer games that depend on lingual movements.

BACKGROUND: Alteration in tongue mobility requires rehabilitation work through oral motor exercises. These exercises can be integrated with computer games to increase the patient's motivation during treatment. OBJECTIVE: To investigate the influence of tongue mobility on children's motor performance in a computer game reliant on lingual movements. METHODS: A cross-sectional descriptive observational study was carried out with 16 children with altered tongue mobility and 16 children with normal tongue mobility. The subjects were between 8 and 12 years of age. They underwent a clinical evaluation of the tongue and performed an activity using an intra-oral joystick controlled by the tongue to play a simple computer game. The game consisted of targets appearing on the screen that the participants had to reach by moving the joystick control rod. Afterward, the participants answered a feedback questionnaire. Motor performance in the game, measured by the number of reached targets and by the time to reach the targets, was compared between groups and across directions of tongue movement and order of appearance of the targets. RESULTS: The group with altered tongue mobility presented a higher time to reach the target in the downward direction and in the first and last 12 targets and a lower number of targets reached in the left direction, upward direction, and in the first 12 targets than the control group. The direction of the movement influenced tongue performance in both groups. CONCLUSION: Children with altered tongue mobility exhibited a worse performance than those with normal tongue mobility.

Protrusive tongue strength in people with severely weak tongues.

The purpose of the study was to quantify tongue protrusion force and compare its characteristics between participants with severely weak tongues and those with normal lingual strength. The sample consisted of 11 participants with severe lingual strength deficits and 11 age- and sex-matched participants with normal lingual strength. Tongue force was evaluated quantitatively using the Forling instrument, and the average force, maximum force, average force application rate, and area under the graphic curve were analysed. These parameters were compared between the groups. In the participants with severely weak tongues, the average and the maximum forces in N (Newton) were 2.03 ± 1.17 and 3.56 ± 1.77, respectively. The average force application rate in N/s (Newton per second) was 1.25 and the area under the graphic curve in Ns (Newton times second) was 18.6. The values of the participants with normal lingual strength were, respectively, 13.27 ± 6.15 N, 18.91 ± 7.95 N, 10.46 N/s, and 108.08 Ns. All parameters analysed differed significantly between the groups. The data collected could aid speech-language pathologists in diagnosing problems related to tongue force.

A finite element model to simulate femoral fractures in calves: testing different polymers for intramedullary interlocking nails.

OBJECTIVE: To verify if the finite element method can correctly estimate the performance of polyacetal and polyamide 6 intramedullary nails in stabilizing a femoral fracture in calves and to estimate the performance of a polypropylene nail in same conditions. STUDY DESIGN: Computational and experimental study. SAMPLE POPULATION: Finite element models (FEMs). METHODS: Based on a 3-dimensional finite element method (FEM) of the femoral diaphysis, 3 models were constructed to simulate an oblique simple fracture stabilized by an intramedullary nail composed of 1 of 3 distinct polymers. Models were tested under 6 loading conditions that simulated a static calf or a calf in different walking phases. Maximum bone and implant stresses were compared to yield and rupture stresses of specific materials. RESULTS: Under static conditions, all polymers were resistant to critical deformation and rupture because maximum von Mises stresses were lower than the respective yield and rupture stresses. However, during walking, maximum stresses exceeded the yield and rupture limits of the polymers, in agreement with a previous in vivo study, which used polyacetal and polyamide nails. CONCLUSIONS: FEM correctly estimated that polyacetal and polyamide 6 nails would fail to immobilize an oblique femoral diaphyseal fracture in calves that were allowed to walk freely during the early postoperative period. FEM can be useful in the development of new bovine orthopedic devices.

3D finite element analysis on esthetic indirect dental restorations under thermal and mechanical loading.

Thermo-mechanical finite element analyses in 3-D models are described for determination of the stress levels due to thermal and mechanical loads in a healthy and restored tooth. Transient thermo-mechanical analysis simulating the ingestion of cold and hot drinks was performed to determine the temperature distribution in the models of the teeth, followed by linear elastic stress analyses. The thermal loads were applied on the occlusal and lingual surfaces. Subsequently, coupled variation of the temperature and mastication loading was considered. The vertical loading was distributed at occlusal points, adding up to 180 N. Maximum stresses were verified in resin restoration under thermal loads. When studying coupled effect of mechanical loading with that arising from thermal effects, higher tensile stress values occurred in porcelain restorations, especially at the restoration-dentin interface. Regions of high tensile stress were detected and their possible clinical significance with respect to restoration damage and microleakage were discussed.

Abfraction and anisotropy--effects of prism orientation on stress distribution.

This work discusses the effect of enamel anisotropy in the stress concentration at the cement-enamel junction (CEJ), a probable cause of fracture in enamel leading to abfraction. Usual simplifications when developing computer models in dentistry are to consider enamel isotropic, or that the direction of the prisms is orthogonal to either the dentine-enamel interface or the tooth outer surface. In this paper, a more refined model for the material behavior is described, based on laboratory observation and on the work of Fernandes and Chevitarese. The material description is used in a two-dimensional (2D) finite element model of the first upper premolar, and the analysis is performed for two different situations: vertical loads, typical of normal mastication and horizontal loads, dominant in bruxism. The analyses were performed using a unit load, which under the hypothesis of linear response of the tooth, allows the combinations described in the text to simulate different functional and parafunctional loads. The results indicate that a realistic enamel description in terms of mechanical properties and spatial distribution of its prisms alters significantly the resulting stress distribution. For all cases included in this study, the detailed description of prism orientation and resulting anisotropy led to improved response in terms of stress distribution, even when loading was horizontal.