RESUMO
AIM AND OBJECTIVES: In the denture wearing people, saliva is necessary to create adhesion, cohesion, and surface tension that ultimately leads to the increased retention of the denture. Medications have some influence on the flow rate of saliva and denture retention. The present study evaluates the effect of complete denture wear on the flow rate of saliva in both medicated and apparently healthy patients. MATERIALS AND METHODS: The participants were 42 edentulous individuals aged 35-70 years requiring complete denture prostheses. The participants were divided into two groups of medicated and unmedicated. Unstimulated whole saliva was collected at 24 h and 3 months after the insertion of new complete dentures in both the groups. The data obtained were analyzed using Student's paired t-test and unpaired t-test. Intergroup changes were compared with unpaired t-test. Intragroup changes were compared with paired t-test using the Statistical Package for Social Sciences, version 22.0. RESULTS: In the unmedicated group, the mean salivary flow rate was high at 24 h after denture insertion when compared to before denture insertion (P = 0.001 VHS). In the medicated group, the observation was highly significant (P = 0.007 HS) 24 h after denture insertion and after 3 months (P = 0.02 S) when compared to before denture insertion. CONCLUSION: No significant difference in the salivary flow rate was found 3 months after denture insertion when compared to before denture insertion for both the medicated and unmedicated groups.
RESUMO
BACKGROUND: Traumatic injuries caused to anterior teeth are most common. Emergency management of fractured fragments is necessary, for preserving their vitalities and for retaining aesthetics in an economical way. Various methods are available for restoring fractured, uncomplicated teeth, such as reattachment of fractured fragments, composite restoration. But only limited data is available on evaluation of the strength of reattached fractured fragments. Hence, the present study was designed. OBJECTIVES: The objective of this study was to evaluate the fracture strength recovery of re-attached anterior fractured tooth fragment by using different re-attachment techniques. METHODOLOGY: Forty human upper central incisions were used in this study. The roots of the teeth were confined in a special device (holder) and adapted in a Universal Testing Machine. Load was applied to each tooth in bucco-lingual direction, by using a small stainless steel ball. The force which was required to fracture the tooth was recorded. Both the fragment and remaining fractured tooth was restored by using four reattachment techniques - simple reattachment, external chamfer, over contour and internal dentinal groove. Specimens were loaded in same pre-determined area which was used in procedure to obtain fragments. The force required to detach each fragment was recorded and it was correlated with the fracture strength of an intact tooth and that which was obtained after doing restorative procedures for all groups i.e. fracture strength recovery. RESULTS: Technique I (simple reattachment) and Technique 2 (external chamfer) showed fracture strength recoveries of 44.3% and 60.6% respectively. However, these values were lower than those which were obtained by usingTechnique 3 (Over contour) -86.8% and Technique 4 (internal dentinal groove) -89.5%. CONCLUSION: Over contour and internal dentinal groove reattachment is a preferred technique as compared to the other reattachment techniques which were tested.
RESUMO
BACKGROUND: The condition of the denture bearing tissues may be adversely affected by high stress concentration during function. Chairside Denture (Hard and Soft) reliners are used to distribute forces applied to soft tissues during function. Tensile and shear bond strength has been shown to be dependent on their chemical composition. A weak bond could harbor bacteria, promote staining and delamination of the lining material. To investigate tensile and shear bond strength of 4 different commercially available denture relining materials to conventional heat cured acrylic denture base resin. MATERIALS & METHODS: 4 mm sections in the middle of 160 Acrylic cylindrical specimens (20 mm x 8 mm) were removed, packed with test materials (Mollosil, G C Reline Soft, G C Reline Hard (Kooliner) and Ufi Gel Hard and polymerized. Specimens were divided into 8 groups of 20 each. Tensile and shear bond strength to the conventional heat cured acrylic denture base resin were examined by Instron Universal Tensile Testing Machine using the equation F=N/A (F-maximum force exerted on the specimen (Newton) and A-bonding area= 50.24 mm2). One-way ANOVA was used for multiple group comparisons followed by Bonferroni Test and Hsu's MCB for multiple pairwise comparisons to asses any significant differences between the groups. RESULTS: The highest mean Tensile bond strength value was obtained for Ufi Gel Hard (6.49+0.08 MPa) and lowest for G C Reline Soft (0.52+0.01 MPa). The highest mean Shear bond strength value was obtained for Ufi Gel Hard (16.19+0.1 MPa) and lowest for Mollosil (0.59+0.05 MPa). The Benferroni test showed a significant difference in the mean tensile bond strength and the mean shear bond strength when the two denture soft liners were compared as well as when the two denture hard liners were compared. Hsu's MCB implied that Ufi gel hard is better than its other closest competitors. CONCLUSION: The Tensile and Shear bond strength values of denture soft reliners were significantly lower than denture hard reliners. How to cite the article: Lau M, Amarnath GS, Muddugangadhar BC, Swetha MU, Das KA. Tensile and shear bond strength of hard and soft denture relining materials to the conventional heat cured acrylic denture base resin: An In-vitro study. J Int Oral Health 2014;6(2):55-61.
