Influence of static compression on mechanical parameters of acoustic foams.

The modification of elastic properties of compressed acoustic foams is investigated. The porous sample is first submitted to a static compression and then to a dynamic excitation of smaller amplitude, corresponding to acoustical applications. The static compression induces the modification of the dynamic elastic parameters of the material. This work focuses on Young's modulus. The variation is measured with two different experimental methods: The classical rigidimeter and an absorption measurement. The effective Young's modulus is directly measured with the first method and is indirectly determined through the quarter-wave length resonance of the frame with the second one. The results of the two measurements are compared and give similar tendencies. The variation of the dynamic Young's modulus as a function of the degree of compression of the sample is shown to be separated in several zones. In the zones associated with weak compression (those usually zones encountered in practice), the variation of the effective Young's modulus can be approximated by a simple affine function. The results are compared for different foams. A simple model of the dependency of the Young's modulus with respect to the static degree of compression is finally proposed for weak compressions.

Absorption of a rigid frame porous layer with periodic circular inclusions backed by a periodic grating.

The acoustic properties of a periodic rigid frame porous layer with multiple irregularities in the rigid backing and embedded rigid circular inclusions are investigated theoretically and numerically. The theoretical representation of the sound field in the structure is obtained using a combination of multipole method that accounts for the periodic inclusions and multi-modal method that accounts for the multiple irregularities of the rigid backing. The theoretical model is validated against a finite element method. The predictions show that the acoustic response of this structure exhibits quasi-total, high absorption peaks at low frequencies which are below the frequency of the quarter-wavelength resonance typical for a flat homogeneous porous layer backed by a rigid plate. This result is explained by excitation of additional modes in the porous layer and by a complex interaction between various acoustic modes. These modes relate to the resonances associated with the presence of a profiled rigid backing and rigid inclusions in the porous layer.

Prediction of sound reflection by corrugated porous surfaces.

The coupled mode (CM) and finite-element methods (FEMs) are developed and used to predict the acoustic reflection coefficient of a semi-infinite porous medium with closely spaced two-dimensional (2D) periodical corrugations. These methods are also applied to predict the reflection coefficient of a periodic array of porous corrugations installed on an acoustically rigid surface. It is shown that the predictions by the both methods agree closely. The reflection coefficient and Brewster angle of total refraction for the corrugated semi-infinite medium predicted with these methods are compared against that predicted by the Biot/Tolstoy/Howe/Twersky and extended Twersky models. A similar analysis is carried out for porous corrugations set on a rigid backing. The behavior of the reflection coefficient and the pole in the expression for the reflection coefficient located close to grazing incidence is studied.

Total absorption peak by use of a rigid frame porous layer backed by a rigid multi-irregularities grating.

The acoustic properties of a low resistivity porous layer backed by a rigid plate containing periodic rectangular irregularities, creating a multicomponent diffraction gratings, are investigated. Numerical and experimental results show that the structure possesses a total absorption peak at the frequency of the modified mode of the layer, when designed as proposed in the article. These results are explained by an analysis of the acoustic response of the whole structure and especially by the modal analysis of the configuration. When more than one irregularity per spatial period is considered, additional higher frequency peaks are observed.

Analytical method for the ultrasonic characterization of homogeneous rigid porous materials from transmitted and reflected coefficients.

A frequency domain method dedicated to the analytic recovery of the four relevant parameters of macroscopically homogeneous rigid frame porous materials, e.g., plastic foams, at the high frequency range of the Johnson-Champoux-Allard model is developed and presented. The reconstructions appeal to experimental data concerning time domain measurements of the ultrasonic fields reflected and transmitted by a plate of the material at normal incidence. The effective density and bulk modulus of the material are first reconstructed from the frequency domain reflection and transmission coefficients. From the latter, the porosity, tortuosity, and thermal and viscous characteristic lengths are recovered. In a sense, the method presented herein is quite similar in the ultrasonic range, but also quite complementary, to the method developed by Panneton and Olny [J. Acoust. Soc. Am. 119, 2027-2040 (2006); 123, 814-824 (2008)] at low frequency, which appeal to experimental data measured in an impedance tube.

Sound transmission through finite lightweight multilayered structures with thin air layers.

The sound transmission loss (STL) of finite lightweight multilayered structures with thin air layers is studied in this paper. Two types of models are used to describe the vibro-acoustic behavior of these structures. Standard transfer matrix method assumes infinite layers and represents the plane wave propagation in the layers. A wave based model describes the direct sound transmission through a rectangular structure placed between two reverberant rooms. Full vibro-acoustic coupling between rooms, plates, and air cavities is taken into account. Comparison with double glazing measurements shows that this effect of vibro-acoustic coupling is important in lightweight double walls. For infinite structures, structural damping has no significant influence on STL below the coincidence frequency. In this frequency region, the non-resonant transmission or so-called mass-law behavior dominates sound transmission. Modal simulations suggest a large influence of structural damping on STL. This is confirmed by experiments with double fiberboard partitions and sandwich structures. The results show that for thin air layers, the damping induced by friction and viscous effects at the air gap surfaces can largely influence and improve the sound transmission characteristics.

Acoustic response of a rigid-frame porous medium plate with a periodic set of inclusions.

The acoustic response of a rigid-frame porous plate with a periodic set of inclusions is investigated by a multipole method. The acoustic properties, in particular, the absorption, of such a structure are then derived and studied. Numerical results together with a modal analysis show that the addition of a periodic set of high-contrast inclusions leads to the excitation of the modes of the plate and to a large increase in the acoustic absorption.

A description of transversely isotropic sound absorbing porous materials by transfer matrices.

A description of wave propagation in transversely isotropic porous materials saturated by air with a recent reformulation of the Biot theory is carried out. The description is performed in terms of a transfer matrix method (TMM). The anisotropy is taken into account in the mechanical parameters (elastic constants) and in the acoustical parameters (flow resistivity, tortuosity, and characteristic lengths). As an illustration, the normal surface impedance at normal and oblique incidences of transversely isotropic porous layers is predicted. Comparisons are performed with experimental results.

Reconstruction of material properties profiles in one-dimensional macroscopically inhomogeneous rigid frame porous media in the frequency domain.

The present paper deals with the inverse scattering problem involving macroscopically inhomogeneous rigid frame porous media. It consists of the recovery, from acoustic measurements, of the profiles of spatially varying material parameters by means of an optimization approach. The resolution is based on the modeling of acoustic wave propagation in macroscopically inhomogeneous rigid frame porous materials, which was recently derived from the generalized Biot's theory. In practice, the inverse problem is solved by minimizing an objective function defined in the least-square sense by the comparison of the calculated reflection (and transmission) coefficient(s) with the measured or synthetic one(s), affected or not by additive Gaussian noise. From an initial guess, the profiles of the x-dependent material parameters are reconstructed iteratively with the help of a standard conjugate gradient method. The convergence rate of the latter and the accuracy of the reconstructions are improved by the availability of an analytical gradient.

Application of the biot model to ultrasound in bone: direct problem.

Ultrasonic wave propagation in human cancellous bone is considered using Biot's theory modified by the Johnson-Koplik-Dashen model for viscous exchange between fluid and structure. The transmission coefficient is derived for a slab of porous material. Experimental results for fast and slow waves transmitted through human cancellous bone samples are given and compared with theoretical predictions.

Application of the Biot model to ultrasound in bone: inverse problem.

This paper concerns the ultrasonic characterization of human cancellous bone samples by solving the inverse problem using experimentally measured signals. The inverse problem is solved numerically by the least squares method. Five parameters are inverted: porosity, tortuosity, viscous characteristic length, Young modulus, and Poisson ratio of the skeletal frame. The minimization of the discrepancy between experiment and theory is made in the time domain. The ultrasonic propagation in cancellous bone is modelled using the Biot theory modified by the Johnson-Koplik-Dashen model for viscous exchange between fluid and structure. The sensitivity of the Young modulus and the Poisson ratio of the skeletal frame is studied showing their effect on the fast and slow waveforms. The inverse problem is shown to be well posed, and its solution to be unique. Experimental results for slow and fast waves transmitted through human cancellous bone samples are given and compared with theoretical predictions.

Acoustic probing of the jamming transition in an unconsolidated granular medium.

Experimentally determined dispersion relations for acoustic waves guided along the mechanically free surface of an unconsolidated granular packed structure provide information on the elasticity of granular media at very low pressures that are naturally controlled by the gravitational acceleration and the depth beneath the surface. The experiments confirm recent theoretical predictions that relaxation of the disordered granular packing through nonaffine motion leads to a peculiar scaling of shear rigidity with pressure near the jamming transition corresponding to zero pressure.

Near field Rayleigh wave on soft porous layers.

Simulations performed for a typical semi-infinite reticulated plastic foam saturated by air show that, at distances less than three Rayleigh wavelengths from the area of mechanical excitation by a circular source, the normal frame velocity is close to the Rayleigh pole contribution. Simulated measurements show that a good order of magnitude estimate of the phase speed and damping can be obtained at small distances from the source. Simulations are also performed for layers of finite thickness, where the phase velocity and damping depend on frequency. They indicate that the normal frame velocity at small distances from the source is always close to the Rayleigh pole contribution and that a good order of magnitude estimate of the phase speed of the Rayleigh wave can be obtained at small distances from the source. Furthermore, simulations show that precise measurements of the damping of the Rayleigh wave need larger distances. Measurements performed on a layer of finite thickness confirm these trends.

Prediction of the sound field above a patchwork of absorbing materials.

The aim of this paper is to investigate the acoustic performance of sound absorbing materials through a numerical wave based prediction technique. The final goal of this work is to get insight into the acoustic behavior of a combination of sound absorbing patches. In order to address a wide frequency range, a model based on the Trefftz approach is adopted. In this approach, the dynamic field variables are expressed in terms of global wave function expansions that satisfy the governing dynamic equations exactly. Therefore, approximation errors are associated only with the boundary conditions of the considered problem. This results in a computationally efficient technique. The main advantage of this method is the fact that the sound absorbing patches do not have to be locally reacting. In this article, the wave based method is described and experimentally validated for the case of normal incidence sound absorption identification in a standing wave tube. Afterwards, the method is applied to simulate some interesting setups of absorbing materials.

Measuring permeability of porous materials at low frequency range via acoustic transmitted waves.

An acoustical transmission method is proposed for measuring permeability of porous materials having rigid frame. Permeability is one of the several parameters required by acoustical theory to characterize porous materials such as plastic foams and fibrous or granular materials. The proposed method is based on a temporal model of the direct and inverse scattering problem for the diffusion of transient low frequency waves in a homogeneous isotropic slab of porous material having a rigid frame. This time domain model of wave propagation was initially introduced by the authors [Z.E.A Fellah and C. Depollier, J. Acoust. Soc. Am. 107, 683 (2000)]. The viscous losses of the medium are described by the model devised by Johnson et al. [J. Fluid. Mech. 176, 379 (1987)]. Reflection and transmission scattering operators for a slab of porous material are derived from the responses of the medium to an incident acoustic pulse. The permeability is determined from the expressions of these operators. Experimental and numerical validation results of this method are presented. This method has the advantage of being simple, rapid, and efficient.

Ultrasonic characterization of human cancellous bone using the Biot theory: inverse problem.

This paper concerns the ultrasonic characterization of human cancellous bone samples by solving the inverse problem using experimental transmitted signals. The ultrasonic propagation in cancellous bone is modeled using the Biot theory modified by the Johnson et al. model for viscous exchange between fluid and structure. The sensitivity of the Young modulus and the Poisson ratio of the skeletal frame is studied showing their effect on the fast and slow wave forms. The inverse problem is solved numerically by the least squares method. Five parameters are inverted: the porosity, tortuosity, viscous characteristic length, Young modulus, and Poisson ratio of the skeletal frame. The minimization of the discrepancy between experiment and theory is made in the time domain. The inverse problem is shown to be well posed, and its solution to be unique. Experimental results for slow and fast waves transmitted through human cancellous bone samples are given and compared with theoretical predictions.

Measuring flow resistivity of porous materials at low frequencies range via acoustic transmitted waves.

An acoustic transmissivity method is proposed for measuring flow resistivity of porous materials having rigid frame. Flow resistivity of porous material is defined as the ratio between the pressure difference across a sample and the velocity of flow of air through that sample per unit cube. The proposed method is based on a temporal model of the direct and inverse scattering problem for the diffusion of transient low-frequency waves in a homogeneous isotropic slab of porous material having a rigid frame. The transmission scattering operator for a slab of porous material is derived from the response of the medium to an incident acoustic pulse. The flow resistivity is determined from the solution of the inverse problem. The minimization between experiment and theory is made in the time domain. Tests are performed using industrial plastic foams. Experimental and numerical results, and prospects are discussed.

Investigation of the phase velocities of guided acoustic waves in soft porous layers.

A new experimental method for measuring the phase velocities of guided acoustic waves in soft poroelastic or poroviscoelastic plates is proposed. The method is based on the generation of standing waves in the material and on the spatial Fourier transform of the displacement profile of the upper surface. The plate is glued on a rigid substrate so that it has a free upper surface and a nonmoving lower surface. The displacement is measured with a laser Doppler vibrometer along a line corresponding to the direction of propagation of plane surface waves. A continuous sine with varying frequencies was chosen as excitation signal to maximize the precision of the measurements. The spatial Fourier transform provides the wave numbers, and the phase velocities are obtained from the relationship between wave number and frequency. The phase velocities of several guided modes could be measured in a highly porous foam saturated by air. The modes were also studied theoretically and, from the theoretical results, the experimental results, and a fitting procedure, it was possible to determine the frequency behavior of the complex shear modulus and of the complex Poisson ratio from 200 Hz to 1.4 kHz, in a frequency range higher than the traditional methods.

Ultrasonic wave propagation in human cancellous bone: application of Biot theory.

Ultrasonic wave propagation in human cancellous bone is considered. Reflection and transmission coefficients are derived for a slab of cancellous bone having an elastic frame using Biot's theory modified by the model of Johnson et al. [J. Fluid Mech. 176, 379-402 (1987)] for viscous exchange between fluid and structure. Numerical simulations of transmitted waves in the time domain are worked out by varying the modified Biot parameters. The variation is applied to the governing parameters and is about 20%. From this study, we can gain an insight into the sensitivity of each physical parameter used in this theory. Some parameters play an important role in slow-wave wave form, such as the viscous characteristic length lambda and pore fluid bulk modulus Kf. However, other parameters play an important role in the fast-wave wave form, such as solid density rhos and shear modulus N. We also note from these simulations that some parameters such as porosity phi, tortuosity alpha(infinty), thickness, solid bulk modulus Ks, and skeletal compressibility frame Kb, play an important role simultaneously in both fast and slow wave forms compared to other parameters which act on the wave form of just one of the two waves. The sensitivity of the modified Biot parameters with respect to the transmitted wave depends strongly on the coupling between the solid and fluid phases of the cancellous bone. Experimental results for slow and fast waves transmitted through human cancellous bone samples are given and compared with theoretical predictions.

Determination of transport parameters in air-saturated porous materials via reflected ultrasonic waves.

An ultrasonic reflectivity method of evaluating the acoustic parameters of porous materials saturated by air (or any other gas) is discussed. The method is based on experimental detection of waves reflected at normal incidence by the first and second interface of the material. This method is based on a temporal model of direct and inverse scattering problems for the propagation of transient ultrasonic waves in a homogeneous isotropic slab of porous material with a rigid frame [Fellah et al., J. Acoust. Soc. Am. 113, 61-73 (2003)]. Generally, the conventional ultrasonic approach can be used to determine tortuosity, and viscous and thermal characteristic lengths via transmitted waves. Porosity cannot be estimated in transmitted mode because of its very weak sensitivity. First interface use of the reflected wave at oblique incidence leads to the determination of porosity and tortuosity [Fellah et al., J. Acoust. Soc. Am. 113, 2424-2433 (2003)] but this is not possible at normal incidence. Using experimental data of reflected waves by the first and second interface at normal incidence simultaneously leads to the determination of porosity, tortuosity, viscous and thermal characteristic lengths. As with the classic ultrasonic approach for characterizing porous material saturated with one gas, both characteristic lengths are estimated individually by assuming a given ratio between them. Tests are performed using weakly resistive industrial plastic foams. Experimental and numerical results, and prospects are discussed.