Densification effect on field emission characteristics of CNT film emitters for electron emission devices.

Field electron emission characteristics of the carbon nanotube (CNT) film emitters were investigated according to densification conditions such as nitric acid, acetic acid, and salicylic acid. The emission performance of the CNT film emitters was strongly affected by the densification conditions. Salicylic acid exhibits the best field electron emission properties of the CNT film emitters, followed by nitric acid and acetic acid. The efficient densification of the CNT film emitter by salicylic acid is caused by the role of polarity and p orbitals, nitric acid by hydrogen ions, and acetic acid by weak polarity. After the densification with salicylic acid, the turn-on field of the CNT film emitter decreases from 1.94 Vµm-1to 1.86 Vµm-1, the threshold field decreases from 3.41 Vµm-1to 2.95 Vµm-1, the emission current significantly increases from 20.92 mA to 43.98 mA, and the degradation rate from the long-term emission stability decreases from 49.9% to 21%. The improved emission characteristics are attributed to the increased emission sites at the CNT film and the increased electrical conductivity of the CNT film. The densification is a useful way to enhance the field electron emission properties of CNT film emitters.

Fabrication of Wearable Transistor with All-Graphene Electrodes via Hot Pressing.

Textile electronics are ideal for novel electronic devices owing to their flexibility, light weight, and wearability. In this work, wearable organic field-effect transistors (OFETs) with all-graphene electrodes, fabricated using hot pressing, are described. First, highly conductive and flexible electrodes consisting of a cotton textile substrate and electrochemically exfoliated graphene (EEG) were prepared via hot pressing. The EEG/textile electrodes exhibited a low sheet resistance of 1.3 Ω sq-1 and high flexibility; these were used as gate electrodes in the wearable OFETs. In addition, spray-coated EEG was also used as the source/drain (S/D) electrodes of the wearable OFETs, which recorded a sheet resistance of 14.8 Ω sq-1 after hot pressing. The wearable OFETs exhibited stable electrical performance, a field-effect mobility of 13.8 cm2 V-1 s-1, and an on-off current ratio of ~103 during 1000 cycles of bending. Consequently, the fabrication method for wearable transistors developed using textiles and hot-pressed graphene electrodes has potential applications in next-generation wearable devices.

High-Performance Cold Cathode X-ray Tubes Using a Carbon Nanotube Field Electron Emitter.

A cold cathode X-ray tube was fabricated using a carbon nanotube (CNT) field electron emitter made by a free-standing CNT film which is composed of a highly packed CNT network. A lot of CNT bundles with a sharp tip are vertically aligned at the edge of the thin CNT film with a length of 10 mm and a thickness of 7 µm. The cold cathode X-ray tube using the CNT field emitter presents an extremely high tube current density of 152 A/cm2 (corresponding to tube current of 106.4 mA), the electron beam transmittance of 95.2% and a small focal spot size (FSS) of 0.5 mm. In addition, the cold cathode X-ray tube also shows stable lifetime during 100 000 shots. High emission current density of the cold cathode X-ray tube is mainly attributed to a lot of electron emission sites at an edge of the CNT film. The small FSS is caused by an ensemble of the CNT field electron emitter made by a free-standing thin CNT film and the optimized curve-shape elliptical focusing lens. Based on obtained results, the cold cathode X-ray tube can be widely used for various X-ray applications such as medical diagnosis systems and security check systems in the future.

Preparation of Nanocomposite-based High Performance Organic Field Effect Transistor via Solution Floating Method and Mechanical Property Evaluation.

We demonstrate that using nanocomposite thin films consisting of semiconducting polymer, poly(3-hexylthiophene) (P3HT), and electrochemically exfoliated graphene (EEG) for the active channel layer of organic field-effect transistors (OFETs) improves both device performances and mechanical properties. The nanocomposite film was developed by directly blending P3HT solution with a dispersion of EEG at various weight proportions and simply transferring to an Si/SiO2 substrate by the solution floating method. The OFET based on P3HT/EEG nanocomposite film showed approximately twice higher field-effect mobility of 0.0391 cm2·V-1·s-1 and one order of magnitude greater on/off ratio of ~104 compared with the OFET based on pristine P3HT. We also measured the mechanical properties of P3HT/EEG nanocomposite film via film-on-elastomer methods, which confirms that the P3HT/EEG nanocomposite film exhibited approximately 2.4 times higher modulus (3.29 GPa) than that of the P3HT film (1.38 GPa), while maintaining the good bending flexibility and durability over 10.0% of bending strain and bending cycles (1000 cycles). It was proved that the polymer hybridization technique, which involves adding EEG to a conjugated polymer, is a powerful route for enhancing both device performances and mechanical properties while maintaining the flexible characteristics of OFET devices.

Field emission behavior of boron nitride nanotubes.

The field emission properties of boron nitride nanotube (BNNT) field emitters according to vacuum pressure were demonstrated. During the short-term emission operation, the field emission behaviors were almost similar, regardless of the vacuum pressure, even though the turn-on electric field of the BNNT field emitter was slightly increased as the vacuum pressure increased. On the other hand, during the long-term emission operation, both the degradation and fluctuations of the emission current of the BNNT field emitters were dramatically increased as the vacuum pressure increased. The degradation of field emission properties of the BNNT emitters according to vacuum pressure is mainly attributed to the ion bombardment effect, rather than the oxidation effect. The field emission behavior under Ar ambient also strongly demonstrates that the degradation and the fluctuation of the emission current are largely dependent on the ion bombardment effect.

Precise Patterning of Organic Single Crystals via Capillary-Assisted Alternating-Electric Field.

Owing to the extraordinary properties, organic micro/nanocrystals are important building blocks for future low-cost and high-performance organic electronic devices. However, integrated device application of the organic micro/nanocrystals is hampered by the difficulty in high-throughput, high-precision patterning of the micro/nanocrystals. In this study, the authors demonstrate, for the first time, a facile capillary-assisted alternating-electric field method for the large-scale assembling and patterning of both 0D and 1D organic crystals. These crystals can be precisely patterned at the photolithography defined holes/channels at the substrate with the yield up to 95% in 1 mm2 . The mechanism of assembly kinetics is systematically studied by the electric field distribution simulation and experimental investigations. By using the strategy, various organic micro/nanocrystal patterns are obtained by simply altering the geometries of the photoresist patterns on substrates. Moreover, ultraviolet photodetectors based on the patterned Alq3 micro/nanocrystals exhibit visible-blind photoresponse with high sensitivity as well as excellent stability and reproducibility. This work paves the way toward high-integration, high-performance organic electronic, and optoelectronic devices from the organic micro/nanocrystals.

High-performance field emission of carbon nanotube paste emitters fabricated using graphite nanopowder filler.

Carbon nanotube (CNT) paste emitters were fabricated using graphite nanopowder filler. The CNT paste emitters consist of CNTs as the emitting material, graphite nanopowder as the filler and a graphite rod as the cathode. Rather than metal or inorganic materials, graphite nanopowder was adapted as a filler material to make the CNT paste emitters. After fabricating the emitters, sandpaper treatment was applied to increase the density of emission sites. The CNT paste emitters showed a high field emission performance, for example a high emission current of 8.5 mA from a cylindrical emitter with a diameter of 0.7 mm (corresponding to a current density of 2.2 A cm-2) and an extremely stable emission current at 1 mA (260 mA cm-2 for 20 h). Interestingly, after a number of electrical arcing events, the emitters still showed a high emission current of 5-8 mA (higher than 1 A cm-2). In addition to the sound electrical and thermal properties of the graphite filler, effective mechanical adhesion of the CNTs onto the graphite cathode induced by the use of the graphite nanopowder filler contributed the excellent field emission properties of the CNT paste emitters.

High-Performance Field-Emission Properties of Boron Nitride Nanotube Field Emitters.

Boron nitride nanotubes (BNNTs) have attracted considerable attention as a field emission material because of their high mechanical strength, high negative electron affinity, and high oxidation resistance. Nevertheless, the obtained field-emission properties of BNNTs have indicated poor emission performance, which is a very high turn-on electric field with a low emission current. We fabricated BNNT field emitters and investigated their field-emission properties. The field-emission properties of the BNNT field emitters were considerably enhanced compared to those of other BN nanomaterial-based field emitters. The turn-on and the threshold electric fields of the BNNT field emitter were 3.1 and 5.4 V/µm at the gap distance of 750 µm, respectively. Both the turn-on and the threshold electric fields of the BNNT field emitters were decreased by increasing the gap distance between the emitter tip and the anode electrode. Degradation of the emission current during field emission operation for 20 h showed no significant difference according to the gap distance. Emission current fluctuation of the BNNT field emitters showed that the smaller gap was more unstable than the larger gap. The enhanced emission properties are mainly attributed to the small diameter, high-quality, and straight structure of BNNTs as well as the stable network formation of the BNNT film with good mechanical and electrical contact between the BNNTs and the cathode electrode. The remarkable emission performance of the BNNT field emitters might have promising applications for various field-emission devices.

Stable p-type properties of single walled carbon nanotubes by electrochemical doping.

We report a highly stable p-type doping for single walled carbon nanotubes using an electrochemical method. The Raman spectroscopy showed the upshift of the G-band when the applied potential increased. Furthermore, the carbon core level shifted as much as 0.14 eV in binding energy of XPS measurement, which is an evidence of p-type doping with a Fermi level change. The highly doped SWCNTs at an applied potential of 1.5 V during the electrochemical doping process showed long time stability, as long as 28 days.

Large-area atomically thin MoS2 nanosheets prepared using electrochemical exfoliation.

Molybdenum disulfide (MoS2) is an extremely intriguing material because of its unique electrical and optical properties. The preparation of large-area and high-quality MoS2 nanosheets is an important step in a wide range of applications. This study demonstrates that monolayer and few-layer MoS2 nanosheets can be obtained from electrochemical exfoliation of bulk MoS2 crystals. The lateral size of the exfoliated MoS2 nanosheets is in the 5-50 µm range, which is much larger than that of chemically or liquid-phase exfoliated MoS2 nanosheets. The MoS2 nanosheets undergo low levels of oxidation during electrochemical exfoliation. In addition, microscopic and spectroscopic characterizations indicate that the exfoliated MoS2 nanosheets are of high quality and have an intrinsic structure. A back-gate field-effect transistor was fabricated using an exfoliated monolayer MoS2 nanosheet. The on/off current ratio is over 10(6), and the field-effect mobility is approximately 1.2 cm(2) V(-1) s(-1); these values are comparable to the results for micromechanically exfoliated MoS2 nanosheets. The electrochemical exfoliation method is simple and scalable, and it can be applied to exfoliate other transition metal dichalcogenides.

Investigation of ultraviolet optical properties of semiconducting-enriched and metal-enriched single-walled carbon nanotube networks using spectroscopic ellipsometry.

The ultraviolet optical properties of semiconducting-enriched and metallic-enriched single-walled carbon nanotube (semi-enriched and m-enriched SWCNT) networks were studied using spectroscopic ellipsometry. According to calculated energy loss function, the energy loss peak assigned to the maximum intensity of π-plasmon energy was found to increase from 4.5 eV to 5.0 eV as SWCNT network composition was changed from m-SWCNT enriched to semi-SWCNT enriched. These results clearly demonstrate that the dielectric response in the 4-6 eV range is sensitive to changes in the surrounding dielectric environment depending on the semi-/m-SWCNT content. Therefore, the spectral shift of this energy loss is attributed to the enhanced electron confinement by the presence of the surface plasmon due to a small amount of m-SWCNT, which is an important phenomenon at the SWCNT network.

A fully microfabricated carbon nanotube three-electrode system on glass substrate for miniaturized electrochemical biosensors.

We present an integration process to fabricate single-walled carbon nanotube (SWCNT) three-electrode systems on glass substrate for electrochemical biosensors. Key issues involve optimization of the SWCNT working electrode to achieve high sensitivity, developing an optimal Ag/AgCl reference electrode with good stability, and process development to integrate these electrodes. Multiple spray coatings of the SWCNT film on glass substrate enabled easier integration of the SWCNT film into an electrochemical three-electrode system. O2 plasma etching and subsequent activation of spray-coated SWCNT films were needed to pattern and functionalize the SWCNT working electrode films without serious damage to the SWCNTs, and to remove organic residues. The microfabricated three-electrode systems were characterized by microscopic and spectroscopic techniques, and the electrochemical properties were investigated using cyclic voltammetry and chrono-amperometry. The fully-integrated CNT three-electrode system showed an effective working electrode area about three times larger than its geometric surface area and an improved electrochemical activity for hydrogen peroxide decomposition. Finally, the effectiveness of miniaturized pf-SWCNT electrodes as biointerfaces was examined by applying them to immunosensors to detect Legionella(L) pneumophila, based on a direct sandwich enzyme-linked immunosorbent assay (ELISA) format with 3,3',5,5'-tetramethylbenzidine dihydrochloride/hydrogen peroxide(TMB/H2O2) as the substrate/mediator system. The lower detection limit of the pf-SWCNT-based immunosensors to L. pneumophila is about 1500 times lower than that of the standard ELISA assay.

Plasma-activated carbon nanotube-based high sensitivity immunosensors for monitoring Legionella pneumophila by direct detection of maltose binding protein peptidoglycan-associated lipoprotein (MBP-PAL).

Transferred multi-walled carbon nanotube (MWCNT)-modified platinum thin-film immunosensing electrode material was engineered on a glass substrate and fabricated a fully-integrated electrochemical three-electrode system for monitoring Legionella pneumophila. The transferred MWCNT film was treated with oxygen plasma to improve its electrochemical response and electrical conductivity. We voltammetrically characterized and optimized the electrochemical performance of the fabricated electrode for direct detection of Legionella pneumophila-specific peptidoglycan-associated lipoprotein (PAL) and maltose binding protein (MBP) peptidoglycan-associated lipoprotein (MBP-PAL) fusion. The latter, as an intermediate product to yield the former, has important roles in the growth and purification of PAL, which commercial enzyme-linked immunosorbent assay (ELISA) kits require as a target substrate. Consequently, direct electrochemical detection of MBP-PAL compared to PAL by square-wave voltammetry showed a greater than 50% increase in sensitivity with a lower detection limit of 5 pg mL(-1). We also investigated the affinity properties by determining kinetic parameters of the PAL and the MBP-PAL in relation to polyclonal antibodies immobilized on transferred MWCNT substrates using Michaelis-Menten assumptions and a Hanes-Woolf plot. This new method presented herein could save the time and effort for the separation and purification of PAL form MBP-PAL fusions that are required for performing ELISA-based immunoassay.

Investigation of plasma-functionalized multiwalled carbon nanotube film and its application of DNA sensor for Legionella pneumophila detection.

A novel multiwall carbon nanotube (MWCNT) electrode functionalized with oxygen plasma treatment was prepared and characterized, and its DNA sensing ability for Legionella pneumophila (L. pneumophila) detection was examined using electrochemical measurement. A well-patterned MWCNT working electrode (WE) on a Pt track was fabricated using photolithography, transfer methods and an etching technique. The MWCNT WE was functionalized by oxygen plasma treatment prior to applying for DNA sensor. The surface morphology of the plasma-functionalized MWCNT (pf-MWCNT) WEs were observed by scanning electron microscope (SEM) and the change of chemical composition was characterized by X-ray photoelectron spectroscopy (XPS), and electrochemical measurements were performed using CV with ferricyanide/ferrocyanide redox couple. Effective areas of working electrodes were calculated to be 0.00453 cm(2) for pristine MWCNT electrode and 0.00747-0.00874 cm(2) for pf-MWCNT electrodes with different plasma treatment times. Differential pulse voltammetry (DPV) was carried out in methylene blue solution for DNA sensing. The pf-MWCNT based DNA sensor was successfully operated in a target concentration range of 10 pM to 100 nM and had a lower detection limit than a pristine MWCNT based DNA sensor.

The effect of propofol on emergence agitation in children receiving sevoflurane for adenotonsillectomy.

BACKGROUND: The administration of a single dose of propofol is reported to be effective in decreasing the incidence and severity of emergence agitation (EA) in children following sevoflurane anesthesia. The aim of this study was to investigate the clinical usefulness of a single dose of propofol 1 mg/kg at the end of adenotonsillectomy for reducing the incidence of EA after sevoflurane anesthesia. METHODS: Ninety children, aged 3-8 years, undergoing adenotonsillectomy were randomized into two groups: the propofol group (n = 45) and the saline group (n = 45), of which 88 children completed the study. Anesthesia was maintained with sevoflurane 2-2.5 vol% and nitrous oxide/oxygen (50%/50%). At the completion of adenotonsillectomy, the propofol group patients were given 1 mg/kg of propofol and the saline group patients were given saline 0.1 ml/kg in the same volume. The incidence of EA was assessed with Aono's four point scale and the severity of EA was assessed with pediatric anesthesia emergence delirium (PAED) scale at 5 min (T5), 15 min (T15) and 30 min (T30) after emergence. RESULTS: Of the 88 patients, the incidence of EA at T5, T15 and T30 was 61.4%, 27.3%, and 4.5% in the propofol group while in the saline group was 68.2%, 29.5%, and 9.1%, respectively. The incidence and severity of EA were not found to be significantly different between the two groups, but the scales in each group decreased significantly over time. CONCLUSIONS: The administration of propofol 1 mg/kg at the end of surgery did not have any significant effect in reducing the incidence and severity of EA in children undergoing adenotonsillectomy under sevoflurane anesthesia.

Lambert-Eaton myasthenic syndrome as a cause of persistent neuromuscular weakness after a mediastinoscopic biopsy -A case report-.

There are many causes of prolonged postoperative muscle weakness, including drugs, residual anesthetics, cerebrovascular events, electrolyte imbalance, hypothermia, and neuromuscular disease. Neuromuscular diseases are relatively rare, with the most common being myasthenia gravis and Lambert-Eaton myasthenic syndrome (LEMS). We report an unusual case in which a patient who was given a muscle relaxant during mediastinoscopy developed postoperative muscle weakness that was ultimately diagnosed as secondary to LEMS.

Poly(3-hexylthiophene)/multiwalled carbon hybrid coaxial nanotubes: nanoscale rectification and photovoltaic characteristics.

We fabricate hybrid coaxial nanotubes (NTs) of multiwalled carbon nanotubes (MWCNTs) coated with light-emitting poly(3-hexylthiophene) (P3HT). The p-type P3HT material with a thickness of approximately 20 nm is electrochemically deposited onto the surface of the MWCNT. The formation of hybrid coaxial NTs of the P3HT/MWCNT is confirmed by a transmission electron microscope, FT-IR, and Raman spectra. The optical and structural properties of the hybrid NTs are characterized using ultraviolet and visible absorption, Raman, and photoluminescence (PL) spectra where, it is shown that the PL intensity of the P3HT materials decreases after the hybridization with the MWCNTs. The current-voltage (I-V) characteristics of the outer P3HT single NT show the semiconducting behavior, while ohmic behavior is observed for the inner single MWCNT. The I-V characteristics of the hybrid junction between the outer P3HT NT and the inner MWCNT, for the hybrid single NT, exhibit the characteristics of a diode (i.e., rectification), whose efficiency is clearly enhanced with light irradiation. The rectification effect of the hybrid single NT has been analyzed in terms of charge tunneling models. The quasi-photovoltaic effect is also observed at low bias for the P3HT/MWCNT hybrid single NT.

High-quality thin-multiwalled carbon nanotubes synthesized by Fe-Mo/MgO catalyst based on a sol-gel technique: synthesis, characterization, and field emission.

We synthesized thin-multiwalled carbon nanotubes (t-MWCNTs) using Fe-Mo/MgO catalyst by citrate precursor method based on a simple sol-gel technique. Synthesis of high-quality t-MWCNTs with uniform diameters was achieved in large-scale by catalytic decomposition of methane over Fe-Mo/MgO catalyst prepared under Ar-atmosphere. The produced t-MWCNTs had the outer diameters in the range of 4-8 nm, with a Gaussian average diameter of 6.6 +/- 0.1 nm and wall numbers in the range of of 4-7 graphenes. The product yield of the as-synthesized t-MWCNTs was over 450% relative to the used Fe-Mo/MgO catalyst, and TGA showed purity about 85%. The t-MWCNTs showed the low turn-on field about 1.24 V/microm, corresponding to the current density of 0.1 microA/cm2, and the high emission Current density of 10 mA/cm2 at the applied electric field of 2.6 V/microm. The t-MWCNTs indicate good emission stability without any fluctuation of emission current through a lifetime measurement for 20 h. It was confirmed that the field emission performance of t-MWCNTs was similar to DWCNTs and the field emission stability of t-MWCNTs was similar to MWCNTs.

Improved field emission stability of thin multiwalled carbon nanotube emitters.

The improved field emission stability of thin multiwalled carbon nanotube (thin-MWCNT) emitters using a tip sonication process has been investigated. The thin-MWCNTs showed short lengths and many open tips after the tip sonication treatment. The field emission properties of the thin-MWCNT emitters were investigated. Field emission stability dramatically increased as the tip sonication time increased. In particular, field emission current at an acceleration condition was quite stable and showed no degradation for over 19 h after tip sonication treatment of 30 min. Tip sonication could effectively cut CNTs short and regulate the length of CNTs. Therefore, field emission stability was significantly improved during a long period of operation because many shortened thin-MWCNTs could participate in field emission after the treatment.

Field emission characteristics of point emitters fabricated by a multiwalled carbon nanotube yarn.

We fabricated point emitters using a multiwalled carbon nanotube (MWCNT) yarn which was treated by ethylene glycol. The point emitter showed a very high emission current of 3.01 mA (current density of 1.1 x 10(8) A cm(-2)) and good emission stability of over 20 h. We attributed the excellent field emission properties to a large field enhancement factor caused by the large aspect ratio of the sharp tip of the point emitter and the tight bonding of neighboring MWCNTs due to the ethylene glycol treatment. We investigated the field enhancement factor according to the gap between the anode and the emitter tip at a macroscopic gap regime. The measured field enhancement factor of the MWCNT point emitter was in good agreement with theoretical models.