RESUMO
Here, we present the outcomes of four patients with COVID-19 who underwent hematopoietic stem cell transplantation (HSCT) at the National Cancer Center in South Korea. Despite concerns about the unfavorable course of COVID-19 in HSCT recipients, none of our patients experienced severe COVID-19. Moreover, extended viral shedding in case 1, lasting over 100 days, was resolved after successful engraftment. Contracting the virus when the host could not mount enough of an immune reaction might result in a paradoxically favorable course. Vaccination, monoclonal antibodies, and antiviral agent usage against COVID-19 might also be effective. We suggest, if necessary, HSCT should not be deferred in COVID-19 patients.
RESUMO
The pulverization of lithium metal electrodes during cycling recently has been suppressed through various techniques, but the issue of irreversible consumption of the electrolyte remains a critical challenge, hindering the progress of energy-dense lithium metal batteries. Here, we design a single-ion-conductor-based composite layer on the lithium metal electrode, which significantly reduces the liquid electrolyte loss via adjusting the solvation environment of moving Li+ in the layer. A Li||Ni0.5Mn0.3Co0.2O2 pouch cell with a thin lithium metal (N/P of 2.15), high loading cathode (21.5 mg cm-2), and carbonate electrolyte achieves 400 cycles at the electrolyte to capacity ratio of 2.15 g Ah-1 (2.44 g Ah-1 including mass of composite layer) or 100 cycles at 1.28 g Ah-1 (1.57 g Ah-1 including mass of composite layer) under a stack pressure of 280 kPa (0.2 C charge with a constant voltage charge at 4.3 V to 0.05 C and 1.0 C discharge within a voltage window of 4.3 V to 3.0 V). The rational design of the single-ion-conductor-based composite layer demonstrated in this work provides a way forward for constructing energy-dense rechargeable lithium metal batteries with minimal electrolyte content.
Assuntos
Líquidos Corporais , Lítio , Eletrólitos , Íons , MetaisRESUMO
The demand for fast-charging lithium-ion batteries (LIBs) with long cycle life is growing rapidly due to the increasing use of electric vehicles (EVs) and energy storage systems (ESSs). Meeting this demand requires the development of advanced anode materials with improved rate capabilities and cycling stability. Graphite is a widely used anode material for LIBs due to its stable cycling performance and high reversibility. However, the sluggish kinetics and lithium plating on the graphite anode during high-rate charging conditions hinder the development of fast-charging LIBs. In this work, we report on a facile hydrothermal method to achieve three-dimensional (3D) flower-like MoS2 nanosheets grown on the surface of graphite as anode materials with high capacity and high power for LIBs. The composite of artificial graphite decorated with varying amounts of MoS2 nanosheets, denoted as MoS2@AG composites, deliver excellent rate performance and cycling stability. The 20-MoS2@AG composite exhibits high reversible cycle stability (~463 mAh g-1 at 200 mA g-1 after 100 cycles), excellent rate capability, and a stable cycle life at the high current density of 1200 mA g-1 over 300 cycles. We demonstrate that the MoS2-nanosheets-decorated graphite composites synthesized via a simple method have significant potential for the development of fast-charging LIBs with improved rate capabilities and interfacial kinetics.
RESUMO
BACKGROUND: The study was planned to show the status of indoor microorganisms and the status of the reduction device in the military dog clinic. METHODS: Airborne microbes were analyzed according to the number of daily patient canines. For identification of bacteria, sampled bacteria was identified using VITEK®2 and molecular method. The status of indoor microorganisms according to the operation of the ventilation system was analyzed. RESULTS: Airborne bacteria and fungi concentrations were 1000.6 ± 800.7 CFU/m3 and 324.7 ± 245.8 CFU/m3. In the analysis using automated identification system, based on fluorescence biochemical test, VITEK®2, mainly human pathogenic bacteria were identified. The three most frequently isolated genera were Kocuria (26.6%), Staphylococcus (24.48%), and Granulicatella (12.7%). The results analyzed by molecular method were detected in the order of Kocuria (22.6%), followed by Macrococcus (18.1%), Glutamicibacter (11.1%), and so on. When the ventilation system was operated appropriately, the airborne bacteria and fungi level were significantly decreased. CONCLUSION: Airborne bacteria in the clinic tend to increase with the number of canines. Human pathogenic bacteria were mainly detected in VITEK®2, and relatively various bacteria were detected in molecular analysis. A decrease in the level of bacteria and fungi was observed with proper operation of the ventilation system.
RESUMO
Developing a safe and long-lasting lithium (Li) metal battery is crucial for high-energy applications. However, its poor cycling stability due to Li dendrite formation and excessive Li pulverization is the major hurdle for its practical applications. Here, we present a silica (SiO2) nanoparticle-dispersed colloidal electrolyte (NDCE) and its design principle for suppressing Li dendrite formation. SiO2 nanoclusters in the NDCE play roles in enhancing the Li+ transference number and increasing the Li+ diffusivity in the vicinity of the Li-plating substrate. The NDCE enables less-dendritic Li plating by manipulating the nucleation-growth mode and extending Sand's time. Moreover, SiO2 can interplay with the electrolyte components at the Li-metal surface, enriching fluorinated compounds in the solid electrolyte interface layer. The initial control of the Li plating morphology and SEI structure by the NDCE leads to a more uniform and denser Li deposition upon subsequent cycling, resulting in threefold enhancement of the cycle life. The efficacy of the NDCEs has been further demonstrated by the practical battery design, featuring a commercial-level cathode and thin Li-metal (40 µm) anode.
RESUMO
After the Fukushima Dai-ichi nuclear power plant disaster, the demand for a rapid method for the detection of environmental radioactivity increased drastically. Since the development of extraction chromatography using resins, analytical methods have advanced significantly in terms of simplicity and required labor. Herein, a home-made automated separation system that is applicable radio-extraction chromatographic separation techniques is reported. A simple, rapid, and high-throughput method was developed using this home-made automated separation system to analyze radiostrontium in seawater in emergency and routine situations. For emergency situations, radiostrontium in seawater is pre-concentrated on a cation exchange resin and consecutively purified using the Sr-resin. Fifty minutes are required for the purification of 90Sr in four samples (100 ml). The minimum detectable activity (MDA) for 90Sr is 0.2 Bq kg-1 at 100 min counting, with a recovery of 70% and counting efficiency of 95% in the scintillation mode. For routine monitoring, 90Y that is in equilibrium with 90Sr is first separated from the sample matrix using DGA. Treatment of 30 L of each seawater sample requires ~2 h. The MDA for this method is 0.3 mBq kg-1 at 400 min counting with a recovery of 70% and counting efficiency of 67% in the Cerenkov mode. By employing the developed method, the measured 90Sr in seawater collected from the coastal area of Korea is 0.92 ± 0.18 mBq kg-1, which is comparable to that reported previously. The measurements were obtained using a liquid scintillation counter, and the entire separation process was performed by employing the home-made separation system.
RESUMO
Concerns about emerging environmental contaminants have been growing along with industrialization and urbanization around the globe. Among various options for remediating these contaminants, phytotechnology is suggested as a feasible option to maintain the environmental sustainability. The recent advances in phytoremediation, genetic/molecular/omics/metabolic engineering, and nanotechnology are opening new paths for efficient treatment of emerging organic/inorganic contaminants. In this respect, elucidation of molecular mechanisms and genetic engineering of hyperaccumulator plants is expected to enhance remediation of environmental contaminants. This review was organized to offer valuable insights into the molecular mechanisms of phytoremediation and the prospects of transgenic hyperaccumulators with enhanced stress tolerance to diverse contaminants such as heavy metals and metalloids, xenobiotics, explosives, poly aromatic hydrocarbons (PAHs), petroleum hydrocarbons, pesticides, and nanoparticles. The roles of genoremediation and nanoparticles in augmenting the phytoremediation technology are also described in an interrelated framework with biotechnological prospects (e.g., plant molecular nano-farming). Finally, political debate on the preferential use of crops versus non-crop hyperaccumulators in genoremediation, limitations of transgenics in phytotechnologies, and their public acceptance issues are discussed in the policy framework.
Assuntos
Plantas Geneticamente Modificadas , Biodegradação Ambiental , Hidrocarbonetos , Metais Pesados , Poluentes do SoloRESUMO
Spent mushroom substrate (SMS) is a recalcitrant lignocellulosic waste. Recycling of SMS through composting has been reported; however, the process is lengthy due to its complex biochemical composition. Although vermitechnology is known for its high efficiency, it has rarely been applied to recycle SMS. In this study, the qualitative value of vermicomposted SMS mediated by three earthworm species (i.e., Eisenia fetida, Eudrilus eugeniae, and Perionyx excavatus) was evaluated on the basis of nutrient availability, microbial activity, phospholipid fatty acid (PLFA) profiles, and seed germination assays. Degradation profiles of the lignocellulosic substrate in the vermireactors were assessed by monitoring the changes in crystallinity and distribution of functional groups using X-ray diffraction (XRD) and Fourier transform infrared spectroscopy, respectively. Total organic carbon decreased by 1.4-3.5 folds with approximately 2.1-2.4 folds increase in nitrogen and phosphorus availability in all vermibeds. Interestingly, pH declined in the Eisenia and Eudrilus systems but increased in the Perionyx-vermibeds. XRD-derived crystallinity index was reduced significantly by 1.37 folds in Perionyx-vermicompost with concurrent microbial enrichment. Further, profuse abundance of vital functional groups (CO, NH, and OH) was clearly observed in the vermicompost with Perionyx followed by that with Eisenia. Moreover, PLFA illustrated significant variations in fatty acid distributions and microbial communities of the three vermicomposting systems. The seed germination assay showed that the germination index and relative root-shoot vigor of Perionyx-vermicompost treated seeds were 1.05-1.30 times greater than those of Eisenia and Eudrilus vermicompost treated ones. The results suggest that SMS degradability was affected by the growth of a healthy microbial community through vermicomposting.
Assuntos
Agaricales , Compostagem , Microbiota , Oligoquetos , Animais , Biomassa , SoloRESUMO
We present a synergistic strategy to boost the cycling performance of Li-metal batteries. The strategy is based on the combined use of a micropattern (MP) on the surface of the Li-metal electrode and an advanced dual-salt electrolyte (DSE) system to more efficiently control undesired Li-metal deposition at higher current density (â¼3 mA cm-2). The MP-Li electrode induces a spatially uniform current distribution to achieve dendrite-free Li-metal deposition beneath the surface layer formed by the DSE. The MP-Li/DSE combination exhibited excellent synergistic rate capability improvements that were neither observed with the MP-Li system nor for the bare Li/DSE system. The combination also resulted in the Li||LiMn2O4 battery attaining over 1â¯000 cycles, which is twice as long at the same capacity retention (80%) compared with the control cells (MP-Li without DSE). We further demonstrated extremely fast charging at a rate of 15 C (19.5 mA cm-2).
RESUMO
Various electrolytes have been reported to enhance the reversibility of Li-metal electrodes. However, for these electrolytes, concurrent and balanced control of Li-metal and positive electrode interfaces is a critical step toward fabrication of high-performance Li-metal batteries. Here, we report the tuning of Li-metal and lithium cobalt oxide (LCO) interfaces with fluoroethylene carbonate (FEC)-containing electrolytes to achieve high cycling stability of Li/LCO batteries. Reversibility of the Li-metal electrode is considerably enhanced for electrolytes with high FEC contents, confirming the positive effect of FEC on the stabilization of the Li-metal electrode. However, for FEC contents of 50 wt % and above, the discharge capacity is significantly reduced because of the formation of a passivation layer on the LCO cathodes. Using balanced tuning of the two interfaces, stable cycling over 350 cycles at 1.5 mA cm-2 is achieved for a Li/LCO cell with the 1 M LiPF6 FEC/DEC = 30/70 electrolyte. The enhanced reversibility of the Li-metal electrode is associated with the formation of LiF and polycarbonate in the FEC-derived solid electrolyte interface (SEI) layer. In addition, electrolytes with high FEC contents lead to lateral Li deposition on the sides of Li deposits and larger dimensions of rodlike Li deposits, suggesting the elastic and ion-conductive nature of the FEC-derived SEI layer.
RESUMO
Despite the notable progress in the development of rechargeable lithium-sulfur batteries over the last decade, achieving high performance with high-sulfur-loaded sulfur cathodes remains a key challenge on the path to the commercialization of practical lithium-sulfur batteries. This paper presents a novel method by which to fabricate a crack-free sulfur electrode with an ultrahigh sulfur loading (16 mg cm-2) and a high sulfur content (64%). By introducing a porous scaffold on the top of a cast of sulfur cathode slurry, the formation of cracks during the drying of the cast can be prevented due to the lower volume shrinkage of the skin. The scaffold-supported sulfur cathode delivers a notably high capacities of 10.3 mAh cm-2 and 473 mAh cm-3 after a prolonged cycle, demonstrating that the crack-free structure renders more uniform redox reactions at such high sulfur loading. The highly packed, crack-free feature of the sulfur cathode is advantageous, given that it reduces the electrolyte uptake to as low as an E/S ratio of 4 µL mg-1, which additionally contributes to the high energy density. Therefore, the scaffold-supported drying fabrication method as presented here provides an effective route by which to design practically viable, energy-dense lithium-sulfur batteries.
RESUMO
Uncontrolled growth of insulating lithium sulfide leads to passivation of sulfur cathodes, which limits high sulfur utilization in lithium-sulfur batteries. Sulfur utilization can be augmented in electrolytes based on solvents with high Gutmann Donor Number; however, violent lithium metal corrosion is a drawback. Here we report that particulate lithium sulfide growth can be achieved using a salt anion with a high donor number, such as bromide or triflate. The use of bromide leads to ~95 % sulfur utilization by suppressing electrode passivation. More importantly, the electrolytes with high-donor-number salt anions are notably compatible with lithium metal electrodes. The approach enables a high sulfur-loaded cell with areal capacity higher than 4 mA h cm-2 and high sulfur utilization ( > 90 %). This work offers a simple but practical strategy to modulate lithium sulfide growth, while conserving stability for high-performance lithium-sulfur batteries.
RESUMO
To develop standard toxic gas mixtures, it is essential to identify adsorption characteristics of each toxic gas on the inner surface of a gas cylinder. Thus, this study quantified adsorbed amounts of the four toxic gases (nitric oxide [NO], nitrogen dioxide [NO2], sulfur dioxide [SO2], and hydrogen chloride [HCl]) on the inner surface of aluminum cylinders and nickel-coated manganese steel cylinders. After eluting adsorbed gases on the inside of cylinders with ultrapure water, a quantitative analysis was performed on an ion chromatograph. To evaluate the reaction characteristics of the toxic gases with cylinder materials, quantitative analyses of nickel (Ni), iron (Fe), and aluminum (Al) were also performed by inductively coupled plasma optical emission spectrometry (ICP-OES). It was found that the amounts of NO, NO2, and SO2 adsorbed on the inner surface of aluminum cylinders were less than 1.0% at the level of 100 µmol/mol mixing ratio, whereas the signal for most heavy metal elements were below their respective detection limits. This study found that the amounts of HCl adsorbed on the inner surface of nickel-coated manganese steel cylinders were less than 5% at the level of 100 µmol/mol mixing ratio, whereas Ni (86 µmol) and Fe (28 µmol) were detected in the same cylinders. It was revealed that the adsorption mainly took place via the reaction of HCl with inner surface material of nickel-coated manganese steel cylinders. On the other hand, in the case of aluminum cylinders, the amounts of the adsorption were determined to be less than 1% at the level of HCl 100 µmol/mol mixing ratio, whereas most of Ni, Fe, and Al were detected at levels similar to their limits of detection. As a result, this study found that aluminum cylinders are more suitable for preparing HCl gas mixtures than nickel-coated manganese steel cylinders. Implications: To develop a standard toxic gas mixture, it is essential to understand the adsorption characteristics of each toxic gas inside a gas cylinder. It was found that the amounts of NO, NO2, and SO2 adsorbed inside aluminum cylinders were less than 1.0% at the level of 100 µmol/mol mixing ratio. The amounts of HCl adsorbed inside nickel-coated manganese steel cylinders were less than 5% at the level of 100 µmol/mol mixing ratio, whereas those inside aluminum cylinders were less than 1%, indicating that aluminum cylinders are more suitable for preparing HCl gas mixtures.
Assuntos
Ácido Clorídrico/química , Óxido Nítrico/química , Dióxido de Nitrogênio/química , Dióxido de Enxofre/química , Adsorção , Alumínio/química , Ferro/química , Manganês/química , Níquel/química , Aço/química , Água/químicaRESUMO
Industrialization and urbanization have produced a large amount of wastewater. Part of the municipal wastewater has been used as an irrigation source in urban/suburban areas. Its utilization, although economically beneficial, can significantly deteriorate the integrity of the ecological systems (e.g., in terms of quality of soil and resulting food products). The objectives of this study are to investigate the spatial distribution and bio-accumulation of heavy metals (e.g., Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn) in food crops (and topsoil) and associated health risks of their consumption in the area of Mangla Dam, Pakistan. To this end, studies were conducted to assess the risk factors such as the bioconcentration factor (BCF), health risk index (HRI), and daily intake of heavy metals (DIM). Accordingly, there was more contamination in Mangla Dam water irrigated zone (DWI) than in the groundwater irrigated zone (GWI). Co exhibited the maximum BCF of 7.45 for Eruca sativa and 6.61 for Brassica campestris in the GWI zone. Likewise, enhanced risk to human health was seen from of Cd, Cr, and Pb in Triticum aestivum and Eruca sativa grown in the DWI zone. It is recommended that the quality profile of wastewater discharge into freshwater ecosystems should be continuously monitored and regulated.
Assuntos
Monitoramento Ambiental , Metais Pesados/análise , Poluentes do Solo/análise , Humanos , Paquistão , Medição de Risco , Águas Residuárias/químicaRESUMO
Liquid hydrocarbon mixtures such as liquefied petroleum gas and liquefied natural gas are becoming integral parts of the world's energy system. Certified reference materials (CRMs) of liquid hydrocarbon mixtures are necessary to allow assessment of the accuracy and traceability of the compositions of such materials. A piston-type constant-pressure cylinder (PCPC) comprising chambers for a pressurizing gas (helium) and liquid (hydrocarbons) separated by a piston can be used to develop accurate and traceable liquid hydrocarbon mixture CRMs. The development of accurate CRMs relies on the maintenance of their composition. However, a PCPC might allow hydrocarbons to leak owing to the imperfect seal of the piston. In this study, a novel leak-free bellows-type constant-pressure cylinder (BCPC) is designed and evaluated by comparison with PCPCs. Liquid hydrocarbon mixtures consisting of ethane, propane, propene, isobutane, n-butane, 1-butene, and isopentane were prepared in both types of constant pressure cylinders and then monitored to check leakages between the gas and liquid chambers. Overall, notable leakage occurred from and into both chambers in the PCPCs, whereas no leakage occurred in the BCPCs in the three months after their gravimetric preparation. The BCPCs maintained no leakage even 10 months after their preparation, whereas the PCPCs showed significantly increasing leakage during the same period.
RESUMO
Owing to the natural abundance of sodium resources and their low price, next-generation batteries employing an Na metal anode, such as Na-O2 and Na-S systems, have attracted a great deal of interest. However, the poor reversibility of an Na metal electrode during repeated electrochemical plating and stripping is a major obstacle to realizing rechargeable sodium metal batteries. It mainly originates from Na dendrite formation and exhaustive electrolyte decomposition due to the high reactivity of Na metal. Herein, we report a free-standing composite protective layer (FCPL) for enhancing the reversibility of an Na metal electrode by mechanically suppressing Na dendritic growth and mitigating the electrolyte decomposition. A systematic variation of the liquid electrolyte uptake of FCPL verifies the existence of a critical shear modulus for suppressing Na dendrite growth, being in good agreement with a linear elastic theory, and emphasizes the importance of the ionic conductivity of FCPL for attaining uniform Na plating and stripping. The Na-Na symmetric cell with an optimized FCPL exhibits a cycle life two times longer than that of a bare Na electrode.
RESUMO
The Lagrangian FLEXible PARTicle (FLEXPART) dispersion model and National Centers for Environmental Prediction/Global Forecast System (NCEP/GFS) meteorological data were used to simulate the long range transport pathways of three artificial radionuclides: (131)I, (137)Cs, and (133)Xe, coming into Korean Peninsula during the Fukushima Dai-ichi nuclear accident. Using emission rates of these radionuclides estimated from previous studies, three distinctive transport routes of these radionuclides toward the Korean Peninsula for a period from 10 March to 20 April 2011 were exploited by three spatial scales: 1) intercontinental scale - plume released since mid-March 2011 and transported to the North to arrive Korea on 23 March 2011, 2) global (hemispherical) scale - plume traveling over the whole northern hemisphere passing through the Pacific Ocean/Europe to reach the Korean Peninsula with relatively low concentrations in late March 2011 and, 3) regional scale - plume released on early April 2011 arrived at the Korean Peninsula via southwest sea of Japan influenced directly by veering mesoscale wind circulations. Our identification of these transport routes at three different scales of meteorological circulations suggests the feasibility of a multi-scale approach for more accurate prediction of radionuclide transport in the study area. In light of the fact that the observed arrival/duration time of peaks were explained well by the FLEXPART model coupled with NCEP/GFS input data, our approach can be used meaningfully as a decision support model for radiation emergency situations.
Assuntos
Poluentes Radioativos do Ar/análise , Acidente Nuclear de Fukushima , Modelos Teóricos , Monitoramento de Radiação/métodos , Cinza Radioativa/análise , Movimentos do Ar , República da CoreiaRESUMO
The concentrations of PM2.5 and PM10 were monitored at a central urban area of Yongsan (YS), Seoul, Korea during 2013. The daily average concentrations of both PM2.5 and PM10 fractions, were 26.6±12.6 and 45.0±20.4 µg m(-3), respectively. The observed PM2.5 concentration slightly exceeded the annual standard value (25 µg m(-3)) set by the Korean Ministry of Environment (KMOE), while that of PM10 was slightly lower than its guideline value (50 µg m(-3)). Comparison of the monthly mean values (µg m(-3)) of both PM fractions showed maximum concentrations in January (PM2.5: 36.9 and PM10: 59.7) and minimum concentrations in September (PM10: 28.1) and October (PM2.5: 14.9). The existence of strong correlations between the concentrations of PM and some gaseous pollutants (e.g., CO, SO2, and NOx) indicated the commonality of contributing source processes, such as traffic and industrial emissions. The results of a back-trajectory (BT) analysis also suggests that the PM pollution in the study area is likely to have been affected by many sources such as Asian dust, volcanic emissions, and industrial activities in the surrounding countries (China, Russia, and Japan).
Assuntos
Poluentes Atmosféricos/análise , Monitoramento Ambiental , Material Particulado/análise , Poeira/análise , Tamanho da Partícula , Seul , Fatores de Tempo , Erupções VulcânicasRESUMO
Concentrations of 17 trace metals bound in total suspended particulate (TSP) were measured at four urban residential locations (Jong Ro [JR], Gwang Jin [GJ], Gang Seo [GS], and Yang Jae [YJ]) in Seoul, Korea from February to July 2009. The maximum concentrations of metals were recorded by Fe in the range of 2599 (JR) to 2914 ng m(-3) (GJ), while the least values were observed from Ag or Co with a few ng m-3. The relative ordering of the mean concentration (ng m(-3)) at these sites is generally found on the order of Fe>Zn>Ba>Mn>Pb>Cu>B>Cr>Ni>Sr>V>As>Li>Cd>Mo>Co>Ag or with a few exceptions (e.g., a reversal between Ba and Mn or between Ni and Sr). Calculation of the enrichment factor suggests the significant role of man-made processes on such metals as Cd, Zn, and Pb. Inspection of the temporal patterns indicates the peak occurrence of most metals during the spring season due in part to the Asian Dust (AD) event. However, according to the factor analysis, sources of these metals were dominated by both resuspended soil/road dust and the combustion of fossil fuels. The overall results of our study suggest that the interaction between the environmental conditions and roadside traffic activities are paramount in explaining the metal pollution in these urban residential areas.