The effect of contaminating media on the static and dynamic mechanical resilience of dental implant abutments' screws: In vitro study.

INTRODUCTION: This in vitro study aims to biomechanically evaluate the influence of medium contamination for example, saliva, blood, chlorhexidine (liquid and gel), and fluoride mouthwash on the biomechanical behavior of implant abutments' screws under static and dynamic loading. METHODS: Forty five Ti6Al4V commercial dental implants and abutments were tested in this study. Two main mechanical tests were carried out in the selected media. The first, static, aimed to evaluate the torque loss after the first tightening. The second, dynamic, involved a random cyclic load range between 0 and 200 N to evaluate torque loss due to mastication. In addition, metallographic longitudinal and cross-sections of the abutment-implant apparatus were examined to evaluate the abutment screw-abutment-implant interface. RESULTS: The static torque test showed that irrespective of the media, no statistical difference in static torque loss was found prior to dynamic loading. For the dynamic tests, torque-angle evolution analysis during tightening to 30 Ncm and after the spectrum loading, showed the same global mechanical behavior for all media, but the statistical analysis indicated a difference between the groups in reverse torque values (RTV) and in the torque loss due to dynamic loading. The medium groups CHX, CHX-gel, and Fluoride mouthwash, showed a meaningful torque loss due to loading, but the medium groups, control (no medium), blood and saliva showed an opposite trend and required a higher torque to open the abutment screws. The microstructural analysis revealed clear signs of cold-welding/galling, post-dynamic loading in these latter groups. CONCLUSIONS: The presence of lubrication/contamination media (CHX mouthwash/CHX-gel/Fluoride mouthwash) reduces the preload generated due to tightening but prevents damage due to galling. The observed reduction of RTV clearly emphasizes the need for frequent abutment screw retightening for implant-supported prosthetic long-term stability.

Bacterial growth on titanium versus zirconia healing caps. An In vitro study.

Objectives To evaluate and compare bacterial growth on zirconia versus titanium healing caps. Material and methods S. sanguinis (Ss) and F. nucleatum (Fn) were grown on titanium and zirconia healing caps that were fixed to the cover of a 96-well microtiter plate. A drop (10 µL) of bacterial suspension was placed on each healing cap and allowed to dry for 1h at 37°C. After this time, the cover was replaced on the plate such that the caps were completely immersed in fresh liquid medium. Each plate contained only one bacterial strain, with 2 control groups. Bacterial growth was monitored over 18h by following the optical density at 650nm. A one-way ANOVA comparison test was used for statistical analysis. Scanning electron microscope (SEM) images of healing caps of each material were taken after a 48h incubation with Ss or Fn to assess bacterial attachment and with no bacteria as control. Results Ss growth was similar in both types of healing cap with no significant differences between these groups and the control (P=0.990). However, there was significantly less growth of Fn on the zirconia caps than on the titanium samples (P<0.0001) or the control (P<0.0001). SEM imaging revealed obvious differences in the surface characteristics of the titanium and zirconia caps. The number of bacteria attached to the rough apical area was particularly high. Conclusions The use of zirconia healing caps may reduce the growth of some bacterial species compared to that seen on titanium healing caps.

A novel computationally engineered collagenase reduces the force required for tooth extraction in an ex-situ porcine jaw model.

The currently employed tooth extraction methods in dentistry involve mechanical disruption of the periodontal ligament fibers, leading to inevitable trauma to the bundle bone comprising the socket walls. In our previous work, we have shown that a recombinantly expressed truncated version of clostridial collagenase G (ColG) purified from Escherichia coli efficiently reduced the force needed for tooth extraction in an ex-situ porcine jaw model, when injected into the periodontal ligament. Considering that enhanced thermostability often leads to higher enzymatic activity and to set the basis for additional rounds of optimization, we used a computational protein design approach to generate an enzyme to be more thermostable while conserving the key catalytic residues. This process generated a novel collagenase (ColG-variant) harboring sixteen mutations compared to ColG, with a nearly 4℃ increase in melting temperature. Herein, we explored the potential of ColG-variant to further decrease the physical effort required for tooth delivery using our established ex-situ porcine jaw model. An average reduction of 11% was recorded in the force applied to extract roots of mandibular split first and second premolar teeth treated with ColG-variant, relative to those treated with ColG. Our results show for the first time the potential of engineering enzyme properties for dental medicine and further contribute to minimally invasive tooth extraction.

Effect of posterior implant restorations on adjacent teeth and tissues: A case-control study.

INTRODUCTION: Dental implants are an artificial substitute for extracted or missing teeth in the oral cavity and are valuable for improving dental health and quality of life. While many studies on implants can be found, few studies examine their effects on adjacent teeth and tissues. The study aimed to examine complications of teeth adjacent to dental implants in the posterior region. METHODS: In this retrospective case-control study, clinical data of patients treated with implants in the posterior segment were extracted from the medical records in a single community dental clinic between January 9, 2010 and January 9, 2020. The patients were examined clinically and radiographically every 6 months. Data on the adjacent teeth to the dental implants were collected and divided into two groups, complications ("study group") versus no-complications ("control group"). Multivariate logistic regression analysis was performed to find a possible correlation between the complications and the variables checked, followed by checking specific variables in the complication group. RESULTS: A total of 1072 patients were included in the study. There were 179 patients (16.7%) with complications in adjacent teeth, while 893 patients had no documented complications. Predisposing factors for secondary caries were smoking (OR = 2.2, CI = 1.3-3.8) and a higher number of implants (OR = 1.6, CI = 1.1-2.5). Tooth crack and tooth fracture were analyzed together and found to be related to osteoporosis (OR = 8.9, CI = 2.9-27.6), whereas males were more prone to teeth fracture (OR = 2.8, CI = 1.1-7.4). Tooth mobility was related to a higher number of implants (OR = 16.5, CI = 3.7-73.8). Further analyzing the complication group solely, there was a statistical significance for age in primary caries and tooth mobility (p = 0.045). In addition, a higher number of implants was more prevalent with tooth mobility (p = 0.002), wider implant platform was more significant with primary caries (p = 0.012), and periodontal Stage III was more prone to tooth mobility (p < 0.001). The distance between the implant and adjacent tooth was also statistically significant-close proximity with tooth mobility and high distance with dental caries (p = 0.04). CONCLUSIONS: We found a relatively high rate of complications in teeth adjacent to dental implants. Secondary caries was the most common complication. Good understanding and proper position of the implants is essential to avoid adjacent teeth complications.

Outcomes and Complications of 33 Soft-Milled Cobalt-Chromium-Ceramic Full-Arch Screw-Retained Implant-Supported Prostheses: A Retrospective Study with up to 10-Year Follow-Up.

This retrospective study assessed outcomes and complications related to implants and prostheses in edentulous patients treated with soft-milled cobalt-chromium-ceramic full-arch screw-retained implant-supported prostheses (SCCSIPs). After the final prosthesis was delivered, patients participated in an annual dental check-up program, including clinical and radiographic assessments. Outcomes of implants and prostheses were evaluated, and biological and technical complications were categorized as major or minor. Implant and prosthesis cumulative survival rates were assessed using the life table analysis. A total of twenty-five participants (mean age 63.6 ± 7.3 years) with 33 SCCSIPs were observed for a mean of 68.9 ± 27.9 months (range 1-10 years). A total of 7 out of 245 implants were lost, with no effect on prosthesis survival, leading to cumulative survival rates of 97.1% for implants and 100% for prostheses. The most recurrent minor and major biological complications were soft tissue recession (9%) and late implant failure (2.8%). Among 25 technical complications, porcelain fracture was the only major technical complication, requiring prosthesis removal (1%). Porcelain chipping was the most frequent minor technical complication, affecting 21 crowns (5.4%), which required polishing only. At the end of the follow-up, 69.7% of the prostheses were free of technical complications. Within the limitations of this study, SCCSIP showed promising clinical performance after 1-10 years.

Comparative evaluation of shear bond strength of orthodontic brackets bonded to three-dimensionally-printed and milled materials after surface treatment and artificial aging.

Objective: This study aimed to evaluate the shear bond strength (SBS) of orthodontic brackets bonded to three-dimensionally (3D)-printed materials after various surface treatments and artificial aging compared with that bonded to computer-aided design/computer-aided manufacturing (CAD-CAM) polymethyl methacrylate (PMMA)-milled materials. Methods: Eighty cylindrical specimens were 3D printed and divided into the following four subgroups (n = 20 each) according to the surface treatment and artificial aging procedure. Group A, sandblasted with 50 µm aluminum oxide particles (SA) and aging; group B, sandblasted with 30 µm silica-coated alumina particles (CO) and aging; group C, SA without aging; and group D, CO without aging. For the control group, 20 CAD-CAM PMMA-milled cylindrical specimens were sandblasted with SA and aged. The SBS was measured using a universal testing machine (0.25 mm/min), examined at ×2.5 magnification for failure mode classification, and statistically analyzed (p = 0.05). Results: The retention obtained with the 3D-printed materials (groups A-D) was higher than that obtained with the PMMA-milled materials (control group). However, no significant difference was found between the study and control groups, except for group C (SA without aging), which showed significantly higher retention than the control group (PMMA-SA and thermocycling) (p = 0.037). Study groups A-D predominantly exhibited a cohesive specimen mode, indicating specimen fracture. Conclusions: Orthodontic brackets bonded to 3D-printed materials exhibit acceptable bonding strengths. However, 3D-printed materials are prone to cohesive failure, which may result in crown fractures.

Effect of Silica-Modified Aluminum Oxide Abrasion on Adhesion to Dentin, Using Total-Etch and Self-Etch Systems.

This study compared the shear bond strength (SBS) and micromorphology of composite resin to human dentin after pre-treatment with silica-modified aluminum oxide air abrasion. Forty-six molar teeth were treated with either Scotchbond Multi-Purpose (SCMP) or Clearfil SE Bond (CLSE) adhesive. Buccal surfaces were pre-treated with the CoJet air abrasion system (SB), and lingual surfaces were controls. The adhesion of light-cured resin composite to the treated dentin surface was evaluated with SBS. After debonding, substrate surfaces were examined with an optical microscope for failure analysis. In addition, 15 molar teeth were sectioned and randomly assigned to one of five groups, according to the dentin surface pre-treatment and adhesive type, and examined with high-vacuum scanning electron microscopy/energy dispersive X-rays (SEM/EDS). The type of adhesive had a significant effect on SBS (p = 0.000); CLSE had the highest values. SB did not affect SBS (p = 0.090). SEM/EDS revealed residual aluminum and/or silicon on all dentin surfaces after SB, except for the control. Treatment with 32% phosphoric acid in the SCMP adhesive decreased the amounts of aluminum and silicon compared to SB dentin only, whereas CLSE resulted in similar quantities of aluminum and silicon as air-abraded dentin. The results of this study indicate that CLSE might have a higher bond strength to dentin than SCMP. Pre-treatment with SB does not appear to affect bonding strength.

Temporomandibular Disorders and Bruxism among Sex Workers-A Cross Sectional Study.

Sex workers are a highly underprivileged population which is present all around the world. Sex work is associated with negative social stigma which affects all aspects of the sex workers' lives including healthcare, service providers and police. The stigma may result in increased stress, mental health problems, feelings of isolation and social exclusion. In the present study, 36 sex workers (SW) and 304 subjects from the general population in Israel (GP) were evaluated for the presence of bruxism and Temporomandibular disorders (TMD), with the use of Diagnostic Criteria for Temporomandibular Disorders (DC/TMD- Axis I). When compared to the general population, sex workers presented larger maximal assisted mouth opening and higher prevalence of the following TMD diagnoses: Disc displacement with reduction, Myalgia, Myofascial pain with referral, Arthralgia (left and right) and Headache attributed to TMD. The odds of sex workers suffering from one of these diagnoses were twice to five times higher than those of the general population. The study shows that health problems of sex workers go beyond venereal diseases, HIV and mental disorders which are commonly studied. Oral health, TMD and oral parafunctions are some of the additional health issues that should be addressed and explored in this population.

Retrospective 1- to 8-Year Follow-Up Study of Complete Oral Rehabilitation Using Monolithic Zirconia Restorations with Increased Vertical Dimension of Occlusion in Patients with Bruxism.

AIM: The aim of this paper is to perform a retrospective assessment of the clinical performance of the complete oral rehabilitation of patients with bruxism treated with implants and teeth-supported veneered and non-veneered monolithic zirconia restorations with increased occlusal vertical dimension. METHODS: In this retrospective follow-up study, 16 bruxer patients, mean age 59.5 ± 14.9 years, were treated with 152 veneered and 229 non-veneered monolithic zirconia and followed for a mean of 58.8 ± 18.8 months (range 1-8 years). The patients were examined clinically and radiographically, annually. Clinical data were extracted from the medical records. In the recall appointments, modified California Dental Association (CDA) criteria were used to evaluate the restorations. Implant and restoration survival and success rates were recorded and analyzed. RESULTS: The cumulative survival rates of implants and restorations were 97.7% and 97.6%, respectively. Nine restorations were replaced: three due to horizontal tooth fractures, two because of implant failure and four had secondary caries. A total of 43 biologic and technical complications were recorded. In the veneered group, the predominant complication was minor veneer chipping (16.4%), which required polishing only (grade 1). In the non-veneered group, the main complication was open proximal contacts between the implant restorations and adjacent teeth (14.5%). CONCLUSIONS: The survival rates of restorations and implants in patients with bruxism are excellent, even though veneered zirconia restoration exhibited a high rate of minor veneer chipping, which required polishing only. The biologic complication of fractured single-tooth abutment may occur.

Bacterial Growth on Three Non-Resorbable Polytetrafluoroethylene (PTFE) Membranes-An In Vitro Study.

GBR (Guided Bone Regeneration) procedure is challenged by the risk of membrane exposure to the oral cavity and contamination. The barrier quality of these membranes serve as a mechanical block from bacterial penetration into the GBR site. The purpose of this in vitro study was to evaluate the antibacterial effect of three commercial non-resorbable polytetrafluoroethylene membranes. (Two d-PTFE membranes and one double layer e-PTFE +d-PTFE membrane). A validated in vitro model with two bacterial species (Streptococcus sanguinis and Fusobacterium nucleatum) was used. Eight samples from membrane each were placed in a 96-well microtiter plate. The experimental and positive control groups were exposed to a bacterial suspension which involved one bacterial species in each plate. Bacterial growth was monitored spectrophotometrically at 650 nm for 24 h in temperature controlled microplate spectrophotometer under anaerobic conditions. One- Sample Kolmogorov−Smirnov Normal test and the Kruskal−Wallis test was used for the statistical analysis. As shown by the bacterial growth curves obtained from the spectrophotometer readings, all three membranes resulted in bacterial growth. We have not found a statistical difference in F. nucleatum growth between different membrane samples and the positive control group. However, S. sanguinis growth was reduced significantly in the presence of two membranes (CYTOPLAST TXT-200 and NeoGenTM) when compared to the control (p < 0.01). The presence of Permamem® had no significant influence on S. sanguinis growth. Some types of commercial non-resorbable PTFE membranes may have an impact on the growth dynamics of specific bacterial species.

Evaluation of Implant Stability and Trephination Depth for Implant Removal-An In Vitro Study.

Malpositioned and broken implants are usually fully osseointegrated; hence, their removal, especially from the lower arch, can be very challenging. Implant removal techniques include reverse torque and trephination. Trephination is an invasive technique that can jeopardize vital structures, cause mandibular fatigue fractures, or lead to osteomyelitis. In this study, we aimed to assess the relationship between trephination depth and implant stability by recording implant stability quotient (ISQ) readings at varying trephination depths in vitro. Materials and methods: Forty-eight implants were inserted into dense synthetic polyurethane foam blocks as artificial bone. Primary implant stability was measured with a Penguin resonance frequency analysis (RFA) device. Implants of two designs with a diameter of 3.75 mm and a length of 13 or 8 mm were inserted. Twenty-four internal hexagon (IH) (Seven®) and twenty-four conical connection (CC) implants (C1®; MIS® Implants, Ltd., Misgav, Israel) were used. The primary implant stability was measured with the RFA device. Trephination was performed, and implant stability was recorded at depths of 0, 3, and 6 mm for the 8 mm implants and 0, 3, 6, 8, 10, and 11.5 mm for the 13 mm implants. Results: Linear regression revealed a significant relation between the trephination depth and the ISQ (F (1, 213) = 1113.192, p < 0.001, adjusted r2 = 0.839). The trephination depth significantly predicted the ISQ (ß = −5.337, p < 0.001), and the ISQ decreased by −5.33 as the trephination depth increased by 1 mm. Conclusion: Implant stability reduction as measured using an RFA device during trephination may be a valuable guide to achieving safe reverse torque for implant removal. Further studies are needed to evaluate these data in clinical settings.

Primary Implant Stability Analysis of Different Dental Implant Connections and Designs-An In Vitro Comparative Study.

Primary implant stability can be evaluated at the time of placement by measuring the insertion torque (IT). However, another method to monitor implant stability over time is resonance frequency analysis (RFA). Our aim was to examine the effect of bone type, implant design, and implant length on implant primary stability as measured by IT and two RFA devices (Osstell and Penguin) in an in vitro model. Ninety-six implants were inserted by a surgical motor in an artificial bone material, resembling soft and dense bone. Two different implant designs-conical connection (CC) and internal hex (IH), with lengths of 13 and 8 mm, were compared. The results indicate that the primary stability as measured by RFA and IT is significantly increased by the quality of bone (dense bone), and implant length and design, where the influence of dense bone is similar to that of CC design. Both the Osstell and Penguin devices recorded higher primary implant stability for long implants in dense bone, favoring the CC over the IH implant design. The CC implant design may compensate for the low stability expected in soft bone, and dense bone may compensate for short implant length if required by the anatomical bone conditions.

The Accuracy of Open-Tray vs. Snap on Impression Techniques in A 6-Implant Model: An In Vitro 3D Study.

To compare the three-dimensional accuracy of an open-tray and two snap on impression techniques (with and without connecting the plastic caps of the snap on impression transfers) in a full arch 6-implant model, a reference acrylic resin model of the maxilla with six implants was fabricated. Prominent geometrical triangles, in the palate area, served as reference points for a digital overlap between scans. Three impression transfer techniques were evaluated and compared: open-tray direct impression (DI), snap on impression (SpO), and connected snap on impression (SpOC). Polyether impression material was used to make 30 impressions (n = 10), and the master model and all casts were digitally scanned with a laboratory optical scanner. The obtained 3D data were converted and recorded as STL files, which were imported to a 3D inspection software program. Angular deviations (buccal, occlusal and interproximal planes) between the study casts and the reference model were measured. Data were analyzed using one-way analysis of variance (ANOVA) and Tukey post hoc test, with 0.05 used as the level of significance. The 3D angular deviations from the master model revealed no significant differences between the DI and SpO impression groups, but there were significant differences in the SpOC impression group, particularly in the buccal and occlusal planes. In all groups, the 3D angular deviation between the most distal scan abutments on each side of the model was significantly different from all other areas when compared to the master model. Within the limits of this study, it is possible to conclude that the indirect closed tray snap on impression technique with unconnected plastic caps exhibited the same three-dimensional accuracies as the direct open tray technique. The indirect closed tray snap on impression technique with connected plastic caps was less accurate than either the indirect closed tray snap on impression technique with unconnected plastic caps or the direct open tray technique. In the case of full arch implant supported prostheses, inaccuracies may be expected in the most distal implants for all the three impression techniques evaluated in this study. Further in vitro and in vivo research is required.

Painful Temporomandibular Disorders, Bruxism and Oral Parafunctions before and during the COVID-19 Pandemic Era: A Sex Comparison among Dental Patients.

AIM: To evaluate the effect of the current coronavirus pandemic on the prevalence of bruxism, oral parafunctions and painful Temporo-Mandibular Disorders (TMDs) and to evaluate the influence of the pandemic on both sexes. METHODS: This retrospective study included 288 dental patients who underwent complete anamnesis and examination according to the Diagnostic Criteria for TMD. The study evaluated two patient populations according to the date of examination: (a) pre-COVID-19 pandemic era (108 patients); (b) COVID 19 pandemic era, where 180 patients were examined during the pandemic. RESULTS: A significant increase in parafunction activity was found in both men and women (p < 0.001) during the COVID-19 pandemic. Awake bruxism (AB) and sleep bruxism (SB) was more prevalent during the COVID-19 pandemic solely in women (AB-p < 0.001; SB-p = 0.014). CONCLUSIONS: Men and women were affected by the ongoing stress due to the COVID-19 pandemic, yet women showed a higher influence as compared to men. The long-term exposure to elevated levels of anxiety and stress may aggravate or trigger stomatognathic detrimental conditions. Dentists should be aware and regularly monitor their patients regarding the possible existence and consequences of bruxism and TMD.

Survival and Success Rates of Monolithic Zirconia Restorations Supported by Teeth and Implants in Bruxer versus Non-Bruxer Patients: A Retrospective Study.

The aim of this study was to assess retrospectively the survival and success rates of monolithic zirconia restorations supported by teeth and implants in bruxer versus non-bruxer patients. Methods: A total of 15 bruxer and 25 non-bruxer patients attended the recall appointment. The bruxer group (mean age of 61.2 ± 13.3 years and follow-up of 58.7 ± 16.8 months) were treated with 331 monolithic zirconia restorations, while the non-bruxer group, with a comparable mean age and follow-up time, were treated with 306 monolithic zirconia restorations. Clinical data were retrieved from the patients' files. At the recall appointment, all supporting teeth and implants were examined for biological and technical complications, and the restorations were evaluated using modified California Dental Association (CDA) criteria. Data were statistically analyzed using survival analysis methods. A significance level of p < 0.05 was used. A total of 31 versus 27 biologic and technical complications were recorded in the bruxer and non-bruxer groups, respectively. No significant differences were found between the two groups regarding overall complications and survival rate. Regarding the type of complication, a significantly higher rate of veneered porcelain chipping (p = 0.045) was observed in the bruxer group. With regard to biological complications, the only complications that exhibited a borderline, although not significant, difference were three fractured teeth exclusively in the bruxer group (p = 0.051), which were replaced with implant-supported restorations. Within the limitations of this study, we conclude that there were no significant differences in the overall survival and success rates of the monolithic zirconia restorations in bruxer versus non-bruxer patients, although veneered zirconia restorations and single tooth abutments exhibited a higher rate of complications in the bruxer group.

Reliability and Correlation of Different Devices for the Evaluation of Primary Implant Stability: An In Vitro Study.

Our aim was to analyze the correlation between the IT evaluated by a surgical motor and the primary implant stability (ISQ) measured by two RFA devices, Osstell and Penguin, in an in vitro model. This study examines the effect of bone type (soft or dense), implant length (13 mm or 8 mm), and implant design (CC: conical connection; IH: internal hexagon), on this correlation. Ninety-six implants were inserted using a surgical motor (IT) into two types of synthetic foam blocks. Initial measurements for both the peak IT and ISQ were recorded at the point when implant insertion was stopped by the surgical motor, and the final measurements were recorded when the implant was completely inserted into the synthetic blocks using only the RFA devices. Our null hypothesis was that there is a good correlation between the devices, independent of the implant length, design, or bone type. We found a positive, significant correlation between the IT, and the Osstell and Penguin devices. Implant length and bone type did not affect this correlation. The correlation between the devices in the CC design was maintained; however, in the IH design it was maintained only between the RFA devices. We concluded that there is a high positive correlation between the IT and ISQ from a mechanical perspective, which was not affected by bone type or implant length but was affected by the implant design.

Effect of Different Surface Treatments of Lithium Disilicate on the Adhesive Properties of Resin Cements.

The aim of the current study was to evaluate the influence of hydrofluoric (HF) acid concentration and conditioning time on the shear bond strength (SBS) of dual cure resin cement to pressed lithium disilicate ceramic compared to treatment with an Etch and Prime self-etching glass-ceramic primer (EP). A total of 100 samples of pressed lithium disilicate (IPS e.max Press, Ivoclar Vivadent) were randomly divided into five groups (n = 20) according to surface treatment: two different concentrations of HF (5% or 9%), for different durations (20 or 90 s), or treatment with EP. Adhesion of light-cured resin cement to the treated surface was tested by the SBS test. The substrate surfaces of the specimen after failures were examined by SEM. Data were analyzed using Weibull distribution. The highest cumulative failure probability of 63.2% of the shear bond strength (η parameter) values was in the 9% HF -90 s group (17.71 MPa), while the lowest values were observed in the 5% HF -20 s group (7.94 MPa). SBS values were not affected significantly by the conditioning time (20 s or 90 s). However, compared to treatment with 5% HF, surface treatment with 9% HF showed a significantly higher η (MPa) as well as ß (reliability parameter). Moreover, while compared to 9% HF for 20 s, EP treatment did not differ significantly in SBS values. Examination of the failure mode revealed a mixed mode of failure in all the groups. Within the limits of this study, it is possible to assume that IPS e.max Press surface treatment with 9% HF acid for only 20 s will provide a better bonding strength with resin cement than using 5% HF acid.

The Association between Emotional Stress, Sleep, and Awake Bruxism among Dental Students: A Sex Comparison.

Psychosocial factors may play an important role in the etiology of sleep and awake bruxism. The purpose of this study was to assess the relationship between emotional stress and bruxism in male and female dental students at various stages of their education. Dental education in Israel is based on a six-year curriculum, divided into three stages: pre-medical studies (yr. 1-2), manual skills (yr. 3-4), and clinical experience (yr. 5-6). Each stage requires different capabilities and skills. Questionnaires regarding psychological state (SCL-90) measuring depression, anxiety, and somatization as well as stress evaluation questioners (Perceived Stress Scale questionnaire 14) were completed by 387 dental students in the 1st to 6th years. Sleep and awake bruxism were evaluated based on the respondent's awareness. During the manual stage of studies, a significant increase was identified, albeit with weak correlations, between stress scales, depression, anxiety, somatization, and the prevalence of awake bruxism, particularly among males. Only in females was sleep bruxism correlated with emotional parameters, whereas no significant difference in sleep bruxism was observed in males throughout the stages of the study. The manual years of dental education were found to be linked to higher levels of emotional distress and awake bruxism, particularly in men. Sleep bruxism, on the other hand, was not directly linked to emotional factors, implying a distinct etiology.

Upper Lip Horizontal Line: Characteristics of a Dynamic Facial Line.

Background: Upper lip appearance received major attention with the introduction of diverse treatment modalities, including lip augmentation, rhinoplasty surgery, and dental treatment designed to support the upper lip. Our objectives were to define the prevalence and characteristics of the upper lip horizontal line (ULHL), which is a dynamic line appearing during a smile, in relation to gender, malocclusions, aging, and facial morphology. Methods: First, the prevalence and gender distribution of ULHL was examined from standardized en-face imaging at full smile of 643 randomly selected patients. Second, cephalometric and dental cast model analyses were made for 97 consecutive patients divided into three age groups. Results: ULHL appears in 13.8% of the population examined, and prevailed significantly more in females (78%). The prevalence of ULHL was not related to age nor to malocclusion. Patients presenting ULHL showed shorter upper lip and deeper lip sulcus. The skeletal pattern showed longer mid-face, shorter lower facial height and greater prevalence of a gummy smile. Conclusions: Female patients with short upper lip, concavity of the upper lip, and gummy smile are more likely to exhibit ULHL. The ULHL is not age-related and can be identified in children and young adults. Therefore, it should be considered when selecting diverse treatment modalities involving the upper lip.

The Retentive Strength of Zirconium Oxide Crowns Cemented by Self-Adhesive Resin Cements before and after 6 Months of Aging.

The aim of this study was to evaluate the retentive strength of zirconium oxide (yttria-stabilized tetragonal zirconia polycrystals (Y-TZP)) crown-copings treated by combined mechanical and chemical treatments and cemented by four types of self-adhesive resin cements (SARCs) to human prepared teeth, before and after six months of aging in water and thermocycling. A total of 120 molar teeth were mounted, prepared using a standardized protocol and digitally scanned, and Y-TZP copings were produced. Teeth were randomly assigned to four SARC groups. Prior to cementation, the intaglio surfaces of all crowns were sandblasted and then coated with Z-Prime™ Plus (Bisco Dental, Schaumburg, IL, USA). Post cementation, each cement group was subdivided into aged and non-aged groups. After aging, the cemented assemblies were tested for retentive strength using a universal testing machine. Failure analysis was conducted by inspecting all matched debonded surfaces of the teeth and crowns at 3× magnification. Aging treatment did not affect the retentive strength of the Y-TZP crown-copings (p = 0.918). The interaction between cement and aging was statistically significant (p = 0.024). No significant differences in the retentive strengths between the different SARCs were observed pre-aging (p = 0.776), whereas post-aging, Panavia SA (PAN; Kuraray Dental Co Ltd., Osaka, Japan) showed significantly higher strength than RelyX U-200 (RU200; 3M ESPE, Seefeld, Germany). The predominant failure mode was adhesive between the cement and dentin, followed by mixed mode failure.