RESUMO
A pressure shift of Raman band of liquid water (H2O) may be an important tool for measuring residual pressures in mineral inclusions, in situ barometry in high-pressure cells, and as an indicator of pressure-induced structural transitions in H2O. However, there was no consensus as to how the broad and asymmetric water Raman band should be quantitatively described, which has led to fundamental inconsistencies between reported data. In order to overcome this issue, we measured Raman spectra of H2O in situ up to 1.2 GPa using a diamond anvil cell, and use them to test different approaches proposed for the description of the water Raman band. We found that the most physically meaningful description of water Raman band is the decomposition into a linear background and three Gaussian components, associated with differently H-bonded H2O molecules. Two of these components demonstrate a pronounced anomaly in pressure shift near 0.4 GPa, supporting ideas of structural transition in H2O at this pressure. The most convenient approach for pressure calibration is the use of "a linear background + one Gaussian" decomposition (the pressure can be measured using the formula P (GPa) = -0.0317(3)·ΔνG (cm-1), where ΔνG represents the difference between the position of water Raman band, fitted as a single Gaussian, in measured spectrum and spectrum at ambient pressure).
RESUMO
The increasing demand for use of polymers at extreme conditions makes important the exploration of their behavior in a wide pressure and temperature range, which remains unknown for polytetrafluoroethylene (PTFE), one of the most common materials. An in situ Raman spectroscopic study of PTFE shows that it is stable within the range of 2-6 GPa at 500 â and up to 12 GPa at 400 â. At T > 500 â and P > 3.5 GPa, the graphitization of PTFE is observed, but judging from the preservation of liquid run products, PTFE can be used as a material for sample container up to 600 â at this pressure. The obtained data allow the suggestion that the triple point between liquid, solid, and decomposed (carbonized) PTFE is located between 3 and 4 GPa at about 550 â, by analogy with the behavior of polycyclic aromatic hydrocarbons.
RESUMO
Experimental data on the pressure dependence of unit cell parameters for the gas hydrates of ethane (cubic structure I, pressure range 0-2 GPa), xenon (cubic structure I, pressure range 0-1.5 GPa) and the double hydrate of tetrahydrofuran+xenon (cubic structure II, pressure range 0-3 GPa) are presented. Approximation of the data using the cubic Birch-Murnaghan equation, P=1.5B(0)[(V(0)/V)(7/3)-(V(0)/V)(5/3)], gave the following results: for ethane hydrate V(0)=1781 Å(3) , B(0)=11.2 GPa; for xenon hydrate V(0)=1726 Å(3) , B(0)=9.3 GPa; for the double hydrate of tetrahydrofuran+xenon V(0)=5323 Å(3) , B(0)=8.8 GPa. In the last case, the approximation was performed within the pressure range 0-1.5 GPa; it is impossible to describe the results within a broader pressure range using the cubic Birch-Murnaghan equation. At the maximum pressure of the existence of the double hydrate of tetrahydrofuran+xenon (3.1 GPa), the unit cell volume was 86% of the unit cell volume at zero pressure. Analysis of the experimental data obtained by us and data available from the literature showed that 1) the bulk modulus of gas hydrates with classical polyhedral structures, in most cases, are close to each other and 2) the bulk modulus is mainly determined by the elasticity of the hydrogen-bonded water framework. Variable filling of the cavities with guest molecules also has a substantial effect on the bulk modulus. On the basis of the obtained results, we concluded that the bulk modulus of gas hydrates with classical polyhedral structures and existing at pressures up to 1.5 GPa was equal to (9±2) GPa. In cases when data on the equations of state for the hydrates were unavailable, the indicated values may be recommended as the most probable ones.
