Dynamic Hyperspectral Holography Enabled by Inverse-Designed Metasurfaces with Oblique Helicoidal Cholesterics.

Metasurfaces are flat arrays of nanostructures that allow exquisite control of phase and amplitude of incident light. Although metasurfaces offer new active element for both fundamental science and applications, the challenge still remains to overcome their low information capacity and passive nature. Here, by integrating an inverse-designed-metasurface with oblique helicoidal cholesteric liquid crystal (ChOH), simultaneous spatial and spectral tunable metasurfaces with a high information capacity for dynamic hyperspectral holography, are demonstrated. The inverse design facilitates a single-phase map encoding of ten independent holographic images at different wavelengths. ChOH provides precise spectral modulation with narrow bandwidth and wide tunable regime in response to programmed stimuli, thus enabling dynamic switching of the multicolor holography. The results provide simple and generalizable principles for the rational design of interactive metasurfaces that will find numerous applications, including security platform.

Thickness Tolerance in Large-Area Organic Photovoltaics with Fluorine-Substituted Regioregular Conjugated Polymer.

Large areas and simple processing methods are necessary for the commercialization of organic photovoltaics (OPVs). However, the efficiency drop due to the variation in thickness of OPVs limits their large-scale applications. Regioregular polymers with good crystallinity and packing properties that exhibit high charge mobility and extraction ability can help overcome these limitations. In this study, a regioregular polymer named PDBD-2FBT was synthesized. The crystallinity and packing properties of PDBD-2FBT were enhanced by a simple thermal treatment. Using PDBD-2FBT material as a donor and Y6-HU as an acceptor, we fabricated binary blend OPV devices. The devices with optimized active layer thickness achieved a power conversion efficiency (PCE) of 14.14%. A PCE of 13.18% was maintained even in thick-film conditions (400 nm), and thickness tolerance was observed. Based on the thickness tolerance, a 5-line module measuring 36 cm2 was fabricated via the bar-coating method, and a PCE of approximately 10% was achieved.

Large-Area Printed Oxide Film Sensors Enabling Ultrasensitive and Dual Electrical/Colorimetric Detection of Hydrogen at Room Temperature.

Commercial hydrogen (H2) sensors operate at high temperatures, which increases power consumption and poses a safety risk owing to the flammable nature of H2. Here, a polymer-noble metal-metal oxide film is fabricated using the spin-coating and printing methods to realize a highly sensitive, low-voltage operation, wide-operating-concentration, and near-monoselective H2 sensor at room temperature. The H2 sensors with an optimized thickness of Pd nanoparticles and SnO2 showed an extremely high response of 16,623 with a response time of 6 s and a recovery time of 5 s at room temperature and 2% H2. At the same time, printed flexible sensors demonstrate excellent sensitivity, with a response of 2300 at 2% H2. The excellent sensing performance at room temperature is due to the optimal SnO2 thickness, corresponding to the Debye length and the oxygen and H2 spillover caused by the optimized coverage of the Pd catalyst. Furthermore, multistructures of WO3 and SnO2 films are used to fabricate a new type of dual-signal sensor, which demonstrated simultaneous conductance and transmittance, i.e., color change. This work provides an effective strategy to develop robust, flexible, transparent, and long-lasting H2 sensors through large-area printing processes based on polymer-metal-metal oxide nanostructures.

Dual Responsive Dependent Background Color Based on Thermochromic 1D Photonic Crystal Multilayer Films.

In this paper, we present dual responsive one-dimensional (1D) photonic crystal (PC) multilayer films that utilize a high-humidity environment and temperature. Dual responsive 1D PC multilayer films are fabricated on precoated thermochromic film by sequential alternate layer deposition of photo-crosslinkable poly(2-vinylnaphthalene-co-benzophenone acrylate) (P(2VN-co-BPA)) as a high refractive index polymer, and poly(4-vinylpyrollidone-co-benzophenone acrylate) P(4VP-co-BPA) as a low refractive index polymer. The thermochromic film shows a vivid color transition from black to white at 28 °C. Three different colors of thermochromic 1D PC multilayer films are prepared by thickness modulation of P(4VP-co-BPA) layers, and the films on a black background exhibit visible spectrum color only in a high-humidity environment (over 90% relative humidity (RH)). For the three films placed on a hands display, three different composite colors are synthesized by the reflection of light, including yellow, magenta, and cyan, due to the changing of backgrounds from black to white with temperature. Additionally, the films show remarkable color transitions with reliable reversibility. The films can be applied as anti-counterfeiting labels and can be used for smart decoration films. To the best of our knowledge, this is the first report of dual response colorimetric films that change color in various ways depending on temperature and humidity changes, and we believe that it can be applied to various applications.

Adhesion Improvement of Solvent-Free Pressure-Sensitive Adhesives by Semi-IPN Using Polyurethanes and Acrylic Polymers.

To improve the peel strength and holding time of polypropylene glycol (PPG)-based pressure-sensitive adhesives (PSAs), a semi-interpenetrating polymer network (semi-IPN) was prepared using acrylic polymers. In addition, to prevent air pollution due to volatile organic compound emissions and avoid the degradation of physical properties due to a residual solvent, the PPG-based semi-IPN PSAs were fabricated by an eco-friendly solvent-free method using an acrylic monomer instead of an organic solvent. PPG-based semi-IPN PSAs with different hard segment contents (2.9-17.2%) were synthesized; their holding time was found to depend on the hard segment contents. The peel strength was improved because of the formation of the semi-IPN structure. Moreover, the high degree of hard domain formation in the semi-IPN PSA, derived from the increase in the hard segment content using a chain extender, resulted in a holding time improvement. We believe that the as-prepared PSAs can be used in various applications that require high creep resistance.

Background color dependent photonic multilayer films for anti-counterfeiting labeling.

A new concept for anti-counterfeiting security films that utilize the humidity from human breath to reveal a QR code on color-tunable one-dimensional (1D) PC films is presented. The 1D PC film was fabricated on a transparent polyethylene terephthalate (PET) substrate via sequential alternate layer deposition of photo-crosslinkable poly(2-vinylnaphthalene-co-benzophenone acrylate) (P(2VN-co-BPA)) and quaternized poly(4-vinylpyridine-co-benzophenone acrylate) (P(4VP-co-BPA)) (P4QP-51%). The films exhibited remarkable color transitions with reliable reversibility and reproducibility. Films placed on a black background exhibited the full visible spectrum color in a high humidity environment. Additionally, films placed on a white background displayed three different composite colors, including yellow, magenta, and cyan. These films with vivid color transitions in a high humidity environment can be applied as anti-counterfeiting films. A hidden QR code was also laser printed on the initial PC film to enhance the film's anti-counterfeiting security capabilities. These colorimetric 1D PC films can be used as anti-counterfeiting labels and for information storage.

A regioregular donor-acceptor copolymer allowing a high gain-bandwidth product to be obtained in photomultiplication-type organic photodiodes.

Obtaining a photomultiplication-type organic photodiode with a high gain-bandwidth product is challenging. We show that a newly designed regioregular polymer enables the formation of a highly oriented face-on structure with a low trap density, leading to a high EQE and a fast response time. As a result, a gain-bandwidth product of over 4 × 105 Hz is achieved.

Improving the Photostability of Small-Molecule-Based Organic Photovoltaics by Providing a Charge Percolation Pathway of Crystalline Conjugated Polymer.

Photostability of small-molecule (SM)-based organic photovoltaics (SM-OPVs) is greatly improved by utilizing a ternary photo-active layer incorporating a small amount of a conjugated polymer (CP). Semi-crystalline poly[(2,5-bis(2-hexyldecyloxy)phenylene)-alt-(5,6-difluoro-4,7-di(thiophen-2-yl)benzo[c][1,2,5]thiadiazole)] (PPDT2FBT) and amorphous poly[(2,5-bis(2-decyltetradecyloxy)phenylene)-alt-(5,6-dicyano-4,7-di(thiophen-2-yl)benzo[c][1,2,5]thiadiazole)] (PPDT2CNBT) with similar chemical structures were used for preparing SM:fullerene:CP ternary photo-active layers. The power conversion efficiency (PCE) of the ternary device with PPDT2FBT (Ternary-F) was higher than those of the ternary device with PPDT2CNBT (Ternary-CN) and a binary SM-OPV device (Binary) by 15% and 17%, respectively. The photostability of the SM-OPV was considerably improved by the addition of the crystalline CP, PPDT2FBT. Ternary-F retained 76% of its initial PCE after 1500 h of light soaking, whereas Ternary-CN and Binary retained only 38% and 17% of their initial PCEs, respectively. The electrical and morphological analyses of the SM-OPV devices revealed that the addition of the semi-crystalline CP led to the formation of percolation pathways for charge transport without disturbing the optimized bulk heterojunction morphology. The CP also suppressed trap-assisted recombination and enhanced the hole mobility in Ternary-F. The percolation pathways enabled the hole mobility of Ternary-F to remain constant during the light-soaking test. The photostability of Ternary-CN did not improve because the addition of the amorphous CP inhibited the formation of ordered SM domains.

Formation of Large Crystalline Domains in a Semiconducting Polymer with Semi-fluorinated Alkyl Side Chains and Application to High-Performance Thin-Film Transistors.

The semi-fluorinated alkyl (SFA) side chain introduced thienylenevinylene (TV)-based p-type polymer, PC12TVC5F7T, was synthesized for use in organic thin-film transistors (OTFTs). Herein, we investigated the influence of SFA side chains on the morphology, molecular orientation, and crystalline structure using a combination of atomic force microscopy (AFM), scanning electron microscopy (SEM), two-dimensional (2D) grazing-incidence wide-angle X-ray scattering (GIWAXS), and density functional theory (DFT) calculations. Interestingly, the incorporation of SFA side chains led to the evolution of plate-like large-sized domains and also strongly intermolecular stacked high crystalline structures. Furthermore, due to the strong interactions between SFA side chains, several (00h) peaks could be observed for PC12TVC5F7T, in spite of their fairly large dihedral angle. As a result, due to the well-developed microstructure of PC12TVC5F7T, the OTFT devices based on it exhibited a high hole mobility of 1.91 cm2 V-1 s-1, which is an outstanding value among the poly(thiophene) derivative polymers. These observations indicate that large-sized domains and strongly intermolecular stacked high crystalline structures, which are beneficial for charge carrier transport, could be attained by the introduction of SFA side chains, further enhancing the performance of the OTFTs.

Morphology-Dependent Hole Transfer under Negligible HOMO Difference in Non-Fullerene Acceptor-Based Ternary Polymer Solar Cells.

In the field of organic solar cells, it has been generally accepted until recently that a difference in band energies of at least 0.3 eV between the highest occupied molecular orbital (HOMO) level of the donor and the HOMO of the acceptor is required to provide adequate driving force for efficient photoinduced hole transfer due to the large binding energy of excitons in organic materials. In this work, we investigate polymeric donor:non-fullerene acceptor junctions in binary and ternary blend polymer solar cells, which exhibit efficient photoinduced hole transfer despite negligible HOMO offset and demonstrate that hole transfer in this system is dependent on morphology. The morphology of the organic blend was gradually tuned by controlling the amount of ITIC and PC70BM. High external quantum efficiency was achieved at long wavelengths, despite ITIC-to-PC70BM ratio of 1:9, which indicates efficient photoinduced hole transfer from ITIC to the donor despite an undesirable HOMO energy offset. Transient absorption spectra further confirm that hole transfer from ITIC to the donor becomes more efficient upon optimizing the morphology of the ternary blend compared to that of donor:ITIC binary blend.

Reducing Trap-Assisted Recombination in Small Organic Molecule-Based Photovoltaics by the Addition of a Conjugated Block Copolymer.

The performance of organic photovoltaics (OPVs) based on the small-molecule organic semiconductor p-DTS(FBTTh2 )2 is greatly improved by the addition of a conjugated block copolymer composed of difluoroquinoxaline and thienopyrrolodione blocks (D130). The power conversion efficiency (PCE) of the p-DTS(FBTTh2 )2 -based OPV is improved from 5.08% to 6.75% by the addition of 5 wt% D130 to the photoactive layer, which is composed of p-DTS(FBTTh2 )2 and a fullerene derivative. Current-voltage and grazing incidence wide-angle X-ray scattering analyses revealed that the addition of D130 significantly reduces the trap density of the device and changes the packing orientation of p-DTS(FBTTh2 )2 from mostly edge-on to partially face-on. These changes greatly improve the charge carrier mobility of the OPV, indicating that D130 is highly compatible with p-DTS(FBTTh2 )2 . Furthermore, the addition of D130 improve the photostability of the OPV by reducing the burn-in loss under a light soaking intensity of 1 sun. The D130-based OPV maintained 34% of its initial PCE after a light soaking test for 858 h. In contrast, the PCE of the OPV without D130 reduced to 14% of its initial efficiency in the same time period.

High Performance Solution Processed Organic Field Effect Transistors with Novel Diketopyrrolopyrrole-Containing Small Molecules.

The donor-acceptor (D-A)-type diketopyrrolopyrrole (DPP)-based small molecules (LGC-D117 and LGC-D118) were synthesized and used as the active layer of solution-processable organic field-effect transistors (OFETs). Both LGC-D117 and LGC-D118 contain silaindacenodithiophene as electron-donor units with DPP as an electron-accepting linker, and octylrhodanine as the electron-accepting end group. The molecules were functionalized with different side chains to study their effects on OFET characteristics. LGC-D117 has a simple branched alkyl side chain, whereas LGC-D118 features a bulky siloxane-terminated hybrid alkyl chain. The siloxane side chains of LGC-D118 account for its better crystallinity, leading to significantly high field-effect mobility (max 3.04 cm2 V-1 s-1). In particular, LGC-D118 is well soluble and sustains the high mobility in the environmentally friendly 2-methyltetrahydrofuran solvent with low temperature annealing at 100 °C due to the bulky siloxane-terminated alkyl side chain.

Sequential "click" functionalization of mesoporous titania for energy-relay dye enhanced dye-sensitized solar cells.

Energy relay dyes (ERDs) have been investigated previously as a mean to achieve panchromatic spectral response in dye-sensitized solar cells via energy transfer. To reduced the distance between the ERDs and energy-accepting injection dyes (IDs) on the surface of a mesoporous titanium dioxide electrode, the ERDs were immobilized adjacent to the IDs via a sequential functionalization approach. In the first step, azidobenzoic acid molecules were co-adsorbed on the mesoporous titanium dioxide surface with the ID. In the second step, the highly selective copper(I)-catalyzed 1,3-dipolar azide-alkyne cycloaddition "click" reaction was employed to couple an alkyne-functionalized ERD to the azidobenzoic acid monolayer. The cycloaddition step in the mesoporous electrode was slowed dramatically due to reactants and catalysts forming agglomerates. In solar cell devices, the close proximity between the surface-immobilized ERD and energy-accepting squaraine sensitizer dyes results in energy transfer efficiencies of up to 91%. The relative improvement in device performance due to the additional ERD spectral response was 124%, which is among the highest reported. The sequential functionalization approach described herein is transferrable to other applications requiring the functionalization of electrodes with complex molecules.

Ternary bulk heterojunction solar cells: addition of soluble NIR dyes for photocurrent generation beyond 800 nm.

The incorporation of a tert-butyl-functionalized silicon 2,3-naphthalocyanine bis(trihexylsilyloxide) dye molecule as a third component in a ternary blend bulk heterojunction (BHJ) organic solar cell containing P3HT (donor) and PC60BM (acceptor) results in increased NIR absorption. This absorption yields an increase of up to 40% in the short-circuit current and up to 19% in the power conversion efficiency (PCE) in photovoltaic devices. Two-dimensional grazing incidence wide-angle X-ray scattering (2-D GIWAXS) experiments show that compared to the unfunctionalized dye the tert-butyl functionalization enables an increase in the volume fraction of the dye molecule that can be incorporated before the device performance decreases. Quantum efficiency and absorption spectra also indicate that, at dye concentrations above about 8 wt %, there is an approximately 30 nm red shift in the main silicon naphthalocyanine absorption peak, allowing further dye addition to contribute to added photocurrent. This peak shift is not observed in blends with unfunctionalized dye molecules, however. This simple approach of using ternary blends may be generally applicable for use in other unoptimized BHJ systems towards increasing PCEs beyond current levels. Furthermore, this may offer a new approach towards OPVs that absorb NIR photons without having to design, synthesize, and purify complicated donor-acceptor polymers.

A novel thermally reversible soluble-insoluble conjugated polymer with semi-fluorinated alkyl chains: enhanced transistor performance by fluorophobic self-organization and orthogonal hydrophobic patterning.

SFA-PQT exhibits self-assembly via a fluorophobic effect in a non-fluorous solvent, which leads to an enhanced electrical performance. Ambipolar transistors and inverters with p- and n- type bilayers are enabled by the unique thermally reversible soluble-insoluble properties of SFA-PQT. More importantly, the hydrophobicity of SFA-PQT facilitates orthogonal hydrophobic patterning and a patterned inverter exhibits low voltage dissipation, a narrow transition zone, a high gain value, and negligible hysteresis.

Highly soluble energy relay dyes for dye-sensitized solar cells.

High solubility is a requirement for energy relay dyes (ERDs) to absorb a large portion of incident light and significantly improve the efficiency of dye-sensitized solar cells (DSSCs). Two benzonitrile-soluble ERDs, BL302 and BL315, were synthesized, characterized, and resulted in a 65% increase in the efficiency of TT1-sensitized DSSCs. The high solubility (180 mM) of these ERDs allows for absorption of over 95% of incident light at their peak wavelength. The overall power conversion efficiency of DSSCs with BL302 and BL315 was found to be limited by their energy transfer efficiency of approximately 70%. Losses due to large pore size, dynamic collisional quenching of the ERD, energy transfer to desorbed sensitizing dyes and static quenching by complex formation were investigated and it was found that a majority of the losses are caused by the formation of statically quenched ERDs in solution.

Silicon-naphthalo/phthalocyanine-hybrid sensitizer for efficient red response in dye-sensitized solar cells.

Introduction of a naphthalocyanine moiety to phthalocyanine allows for a gradual red shift of the absorption spectrum in the resulting chromophore. Using silicon as a core atom allows for the introduction of additional siloxane side chains which mitigate dye aggregation. A dye-sensitized solar cell with this hybrid sensitizer exhibits a broad and flat IPCE of 80% between 600 and 750 nm and high photocurrent densities of 19.0 mA/cm(2).

High performance weak donor-acceptor polymers in thin film transistors: effect of the acceptor on electronic properties, ambipolar conductivity, mobility, and thermal stability.

We have studied the electronic, physical, and transistor properties of a family of donor-acceptor polymers consisting of diketopyrrolopyrrole (DPP) coupled with different accepting companion units in order to determine the effects of donor-acceptor interaction. Using the electronically neutral benzene (B), the weakly accepting benzothiadiazole (BT), and the strongly accepting benzobisthiadiazole (BBT), the accepting strength of the companion unit was systematically modulated. All polymers exhibited excellent transistor performance, with mobilities above 0.1 cm(2)V(-1)s(-1), even exceeding 1 cm(2)V(-1)s(-1) for one of the BBT-containing polymers. We find that the BBT is the strongest acceptor, enabling the BBT-containing polymers to be strongly ambipolar. The BBT moiety also strengthens interchain interactions, which provides higher thermal stability and performance for transistors with BBT-containing polymers as the active layer.

Ambipolarity in benzobisthiadiazole-based donor-acceptor conjugated polymers.

A family of four new DA polymers, in which the acceptor moiety benzobisthiadiazole was paired with four different donor moieties, has been synthesized. Surpri-singly, all members of the family exhibit balanced ambipolar behavior, despite polymer to polymer mobilities varying from 10(-4) cm(2) V(-1) s(-1) to 10(-1) cm(2) V(-1) s(-1). Applications in single component CMOS integrated circuits are envisioned.

Synthesis and Photovoltaic Properties of a Thienylenevinylene and Diketopyrrolopyrrole Copolymer with High Mobility.

A novel donor-acceptor-type polymer with a low band-gap that alternates electron-rich thienylenevinylene groups with electron-deficient diketopyrrolopyrrole (DPP) units (PETVTDPP) has been synthesized by Pd-catalyzed Stille cross-coupling polymerization. The polymer shows a broad absorption band of wavelengths that range from 330 to 900 nm, and a low band-gap value of 1.43 eV. The field-effect mobility of an organic thin-film transistor based on this polymer is 0.05 cm(2 ) · Vs(-1) . Bulk-heterojunction solar cells using a mixture of PETVTDPP and PC[71] BM for the active layer show a power conversion efficiency (PCE) of 1.94% under simulated AM 1.5 G solar irradiation at 100 mW · cm(-2) .