A Very Rare Form of Ceramic Head Fracture in Bipolar Hemiarthroplasty and Total Hip Arthroplasty: Unique Experience and Literature Review.

Introduction: A fracture of the ceramic head in bipolar hemiarthroplasty using an inner polyliner has not been reported yet, and there seems to be no report of simultaneous breakage of the fourth-generation BIOLOX Delta ceramic head and liner in total hip arthroplasty. Method: A 44-year-old male patient underwent bipolar hemiarthroplasty using a third-generation BIOLOX Forte ceramic head 3 years and 9 months earlier for osteonecrosis of femoral head (ONFH) and visited our hospital due to a ceramic head fracture. Conversion total hip arthroplasty was performed. A 64-year-old female patient underwent total hip arthroplasty using a fourth-generation BIOLOX Delta ceramic head and liner articulation for osteoarthritis of the hip. The ceramic head and liner were fractured during the third dislocation. Ceramic head and liner exchange revision surgery was performed. Conclusion: When using ceramic bearings, fractures or delamination following trauma can occur, confirming the need to carefully evaluate the condition of the ceramic components in symptomatic patients.

Prevalence of Venous Thromboembolism after Immediate Screening in Hip Fracture Patients.

Purpose: Venous thromboembolism (VTE) is a major complication for hip fracture patients, and may exist preoperatively. This study aimed to examine the prevalence of VTE after immediate screening in hip fracture patients. Materials and Methods: Hip fracture patients with an elevated level of D-dimer underwent screening for VTE using computed tomography (CT) angiography. Anticoagulation treatments were administered preoperatively to patients diagnosed with VTE, followed by administration of additional anticoagulation postoperatively. Medical records were reviewed to identify risk factors for preoperative VTE and determine the prognosis of the patients. Results: Among 524 hip fracture patients, 66 patients (12.6%) were diagnosed with VTE, including 42 patients with deep vein thrombosis (DVT), 17 patients with pulmonary thromboembolism (PTE), and 7 patients with both DVT and PTE. Of the patients with VTE, 68.2% were diagnosed within 24 hours of injury, and 33.3% of these patients had PTE. VTE patients showed a tendency toward being overweight (P<0.01) and not on anticoagulant medication (P=0.02) compared to patients without VTE. The risk of VTE was higher for femur shaft fractures (odds ratio [OR] 4.83, 95% confidence interval [CI] 2.18-10.69) and overweight patients (OR 2.12, 95% CI 1.17-3.85), and lower for patients who were previously on anticoagulants (OR 0.36, 95% CI 0.18-0.74). Patients with preoperatively diagnosed VTE were asymptomatic before and after surgery. Conclusion: Clinicians should be aware that VTE may be present within 24 hours of injury, and screening for VTE or prophylactic measures should be considered for high-risk patients.

Incidence and outcomes of intraoperative periprosthetic acetabular fractures during cementless total hip arthroplasty: a prospective three-dimensional computer tomography-based study.

PURPOSE: Unlike periprosthetic femoral fractures, periprosthetic acetabular fractures during total hip arthroplasty (THA) have not been evaluated in detail. We prospectively evaluated the incidence, patterns, risk factors, and clinical outcomes of intraoperative periprosthetic acetabular fractures using pre- and postoperative computer tomography (CT). METHODS: In this prospective single-centre study, we evaluated 234 consecutive patients (250 hips) who underwent THA and three-dimensional CT before and after the surgery. We assessed the incidence, pattern of fractures, outcomes for each fracture pattern, reoperation and revision rates, Harris hip score, and visual analog scale (VAS) for pain. Multivariate regression models were used to identify risk factors for periprosthetic acetabular fractures. RESULTS: In total, 43 periprosthetic acetabular fractures (17.2%) were identified via CT. Fractures occurred most frequently at the superolateral wall. Early cup migration occurred in three hips. None of the patients underwent revision surgery for acetabular loosening. Regression modeling showed that rheumatoid arthritis was a significant predictor of periprosthetic acetabular fractures. CONCLUSIONS: Periprosthetic acetabular fractures are not infrequent during cementless THA and are more common in patients with rheumatoid arthritis.

Non-thermal atmospheric pressure plasma treatment increases hydrophilicity and promotes cell growth on titanium alloys in vitro.

Most medical implants are made of titanium. When titanium is exposed to air for a long time, hydrocarbons are deposited and the surface becomes hydrophobic. Cell attachment is important for bone ingrowth to occur on the implant surface, and hydrophilicity can enhance this. We examined whether non-thermal atmospheric pressure plasma treatment could increase the hydrophilicity of the titanium surface. Samples coated with four widely used coating types [grit blasting, micro arc oxidation (MAO), titanium plasma spray (TPS), and direct metal fabrication (DMF)] were treated with plasma. Each of the four surface-treated samples was divided into groups with and without plasma treatment. We analysed wettability by surface analysis and evaluation of contact angles, cell proliferation, and adhesion using scanning electron microscopy (SEM), confocal laser scanning microscopy, absorbance tests, and alkaline phosphatase (ALP) activity assay; four different Ti6Al4V surface types were compared. After plasma treatment, the contact angle was reduced on all surfaces, and the carbon content was reduced on all surfaces based on X-ray photoelectron spectroscopy (XPS) surface analysis. Under confocal laser scanning, the cell layer was thicker on the plasma-treated samples, especially in groups TPS and DMF. Cell proliferation was 41.8%, 17.7%, 54.9%, and 83.8% greater for the plasma- than non-plasma-treated grit blasting, MAO, TPS, and DMF samples, respectively. Hydrophilicity increased significantly under plasma treatment, and biological responsivity was also improved.

Simple Minimally Invasive Method to Reduce Valgus-Impacted and Tilted Femoral Neck Fractures without Soft Tissue or Cartilage Injury: Radiological and Clinical Results.

OBJECTIVE: This is a rare study comparing the radiological and functional outcomes of fixation after reduction with in situ fixation group using Femoral Neck System (FNS). The aim of this study was to introduce a simple, innovative, minimally invasive method to reduce valgus-impacted and tilted femoral neck fractures without soft tissue or cartilage injury. METHODS: A retrospective comparative analysis of 46 patients between May 2020 and February 2022 was performed. In the control group, 23 patients underwent in situ fixation without reduction. In the study group, another 23 patients were managed by fixation after reduction using a percutaneous pull-out technique with a full threaded Steinmann pin. Caput-collum-diaphysis (CCD) angle, tilt, and femoral neck shortenings were compared between the two groups. In addition, Harris Hip Score (HHS) was evaluated and compared at 1 year after surgery. Basically, independent samples t-test was used to compare radiological and functional results. RESULTS: Patients' initial valgus and tilt angles were not significantly different between the groups (n.s.). However, the CCD and tilt angles measured immediately and at one year postoperatively were significantly different between the groups (p < 0.05). Regarding femoral neck shortening, shortening in the three directions, the x, y, and z vectors, was significantly less in the reduction group immediately postoperatively and at 1 year post-surgery (p < 0.05). The mean HHS at 1 year postoperatively was 79.7 ± 8.4 in the in situ fixation group and 87.9 ± 6.6 in the reduction groups, and there was a significant difference (p < 0.05). CONCLUSION: The pull-out method with a threaded Steinmann pin to reduce valgus-impacted and tilted femoral neck fracture is safe and effective for accomplishing anatomical restoration. This may achieve successful bone union and maintain the femoral neck length and original tilt without nearby soft tissue or cartilage injury.

Is the construct stability of the acetabular cup affected by the acetabular screw configuration in bone defect models?

BACKGROUND: In revision surgery with significant segmental acetabular defects, adequate implant selection and fixation methods are critical in determining successful bony ingrowth. Commercially available total hip prosthesis manufacturers generally offer additional multi-hole options of acetabular shells with identical designs for use in revision THAs where screw holes configurations vary from product to product. This study aims to compare the mechanical stability of the two types of acetabular screw constructs for the fixation of acetabular components: spread-out and pelvic brim-focused configurations. METHODS: We prepared 40 synthetic bone models of the male pelvis. In half of the samples with acetabular defects, identical curvilinear bone defects were manually created using an oscillating electrical saw. On the right side, multi-hole-cups in which the direction of the screw holes are centered on the pelvic brim (brim-focused) and, on the left side, multi-hole-cups with the direction of the screw hole spread throughout the acetabulum (spread-out) were implanted into the pelvic synthetic bones. Coronal lever-out and axial torsion tests were performed with a testing machine, measuring load versus displacement. RESULTS: The average torsional strengths were significantly higher in the spread-out group over the brim-focused group regardless of the presence of the segmental defect of the acetabulum (p < 0.001). But for the lever-out strength, the spread-out group exhibited significantly higher average strength over the brim-focused group for the intact acetabulum (p = 0.004), whereas the results were reversed in the brim-focused group when the defects were generated (p < 0.001). The presence of acetabular defects reduced the average torsional strengths of the two groups by 68.66% versus 70.86%. In comparison, the decrease in the average lever-out strength was less significant for the brim-focused group than the spread-out group (19.87% vs. 34.25%) (p < 0.001). CONCLUSION: Constructs of multi-hole acetabular cups with the spread-out screw holes configuration exhibited statistically better axial torsional strength and coronal lever-out strength. With the presence of posterior segmental bone defects, the spread-out constructs demonstrated significantly better tolerance to axial torsional strength. Still, they exhibited inverted results of higher lever-out strength in the pelvic brim-focused constructs.

Weight-Based Bisphosphonate Administration for Multiple Myeloma Patients and the Risks of Skeletal Complications.

High-dose bisphosphonate for multiple myeloma patients might elevate risks of skeletal complications earlier than general expectations. This study aims to find incidences of atypical femoral fracture (AFF) and medication-related osteonecrosis of the jaw (MRONJ), elucidate their risk factors, and suggest cut-off values for the safer dosing of high-dose bisphosphonate treatment. By using the clinical data warehouse of a single institute, retrospective cohort data of multiple myeloma-diagnosed patients with high-dose bisphosphonate (pamidronate or zoledronate) treatment from 2009 to 2019 was extracted. Among 644 patients, the incidence of prominent AFF requiring surgery was 0.93% (6/644) and MRONJ was diagnosed in 11.8% (76/644) of the study population. For both AFF and MRONJ, the total potency-weighted sum of total dose per body weight (OR = 1.010, p = 0.005) were significant on logistic regression. Cutoffs of the potency-weighted total dose (mg) per body weight (kg) for AFF and MRONJ were 77.00 and 57.70 mg/kg, respectively. After roughly one year of treatment with high-dose zoledronate (about four years for pamidronate), an earlier thorough re-evaluation of skeletal complications should be taken. Body weight adjustments for accumulative dose calculation in terms of permissible dosing should be taken into consideration.

The incidence of focal osteonecrosis of the femoral head and its impact on conversion hip arthroplasty after screw fixation of femoral neck fractures: a multicenter retrospective study based on postoperative magnetic resonance imaging.

PURPOSE: Osteonecrosis of the femoral head (ONFH) and subsequent head collapse is a major concern after internal fixation of femoral neck fracture (FNF). Previous studies focused on ONFH incidence using plain radiography; postoperative magnetic resonance imaging (MRI) was rarely performed. We performed a multicenter retrospective study to investigate the incidence of ONFH and the need for conversion hip arthroplasty after FNF screw fixation. METHODS: We reviewed 195 patients who underwent screw fixation during closed FNF reduction between 2012 and 2017 at three institutions. Except for patients who did not consent to MRI, all patients underwent postoperative MRI either 1-3 years after screw fixation. The occurrence of ONFH was investigated through plain radiography and MRI. RESULTS: Thirty patients were diagnosed with ONFH through plain radiography, and an additional 33 patients were diagnosed with MRI, resulting in a total of 63 patients (32.3%) diagnosed with ONFH. The mean time to ONFH diagnosis was 18.9 months and the conversion rate to hip arthroplasty was 10.2%. Of the 33 patients who were normal on hip radiography but exhibited ONFH on MRI, all had small focal lesions not associated with head collapse at the last follow-up. The ONFH group diagnosed through plain radiography had more unstable FNFs than the group diagnosed through MRI. CONCLUSION: Although postoperative MRI revealed a higher incidence of ONFH after FNF screw fixation than reported previously, the small focal MRI lesions were not associated with increased risks of femoral head collapse or conversion to arthroplasty.

Outcomes of total hip arthroplasty after failed free vascularized fibular grafting for osteonecrosis of the femoral head.

PURPOSE: Total hip arthroplasty (THA) after vascularized fibular grafting (VFG) is technically demanding with poorer outcomes compared to primary THA in patients with osteonecrosis of the femoral head (ONFH). The purpose of this study was to compare the outcomes of THA after VFG after removal of the graft with that of primary THA. METHODS: ONFH patients treated by VFG at a single institution were studied retrospectively. THAs after VFG performed by single arthroplasty surgeon with a single type of THA prosthesis were enrolled in the study. A control cohort of patients was created by 1:1 matching with the THA after VFG cohort according to age, gender, and American Society of Anesthesiology (ASA) score from ONFH patients treated by primary THA. Early and long-term outcomes were compared between the two groups. RESULTS: A total of 24 hips were included in the THA after VFG group and compared with 24 primary THA hips. No significant difference was noted in stem position. The THA after VFG group had increased blood loss and longer duration of operation time. There were two cases of intraoperative femur fractures in the THA after VFG group. The femoral stem of both groups were stable, with no cases of revision, and similar HHS scores at the last follow-up. CONCLUSION: THA after VFG may have similar short to midterm outcomes with primary THA after removal of the residual abutting bone graft and correct positioning of the femoral stem.

Utilizing Three-Dimensional Head-Lesser Trochanter Distance Could Further Reduce Leg Length Inequality in Primary Bipolar Hemiarthroplasty.

Background: The aim of this study was to investigate whether the use of three-dimensional (3-D) computed tomography (CT)-based head-lesser trochanter distance (HLD) could reduce leg length discrepancy (LLD) more than the use of a two-dimensional (2-D) plain film method in primary bipolar hemiarthroplasty. Methods: Propensity score matching (PSM) analysis was used to adjust the confounding factors. A retrospective comparative analysis of 128 patients was performed. In the control group, the leg length was equalized using the 2-D, plain film-based HLD. In the study group, primary bipolar hemiarthroplasty was performed using the 3-D CT-based HLD method. Postoperative LLDs were compared between the two groups using the method of Ranawat. In addition, the Harris hip score (HHS) was evaluated and compared at one year after surgery. Results: A significant difference was observed in mean postoperative LLD between the 2-D HLD group and the 3-D CT HLD group: 1.6 ± 1.2 mm (range, 0.1−6.0 mm) and 1.1 ± 1.2 mm (range, 0.1−5.1 mm), respectively (p < 0.05). Additionally, a higher percentage of patients in the 3-D CT HLD group had an LLD of less than 2 mm. The mean HHS at one year after surgery showed no significant difference between the two groups. Conclusions: To minimize the occurrence of LLD, HLD measurement from a CT scanner may be more accurate than an X-ray. The 2-D and 3-D HLD differences in the 3-D CT HLD group were statistically significant. Using a 3-D, CT-based HLD method might decrease the possibility of an LLD over 2 mm.

Evaluation of transdermal exposure of phthalates in children's products.

In this study, 16 children's products with the highest detection potential of phthalates were selected, and a phthalate assay and transdermal delivery analysis (NIER, US EPA Wipe [stress condition], US EPA Wipe [physiological condition], and US EPA Hand Wipe) were conducted with these products. The content of 6 controlled phthalates (DBP, BBP, DEHP, DNOP, DINP, and DIDP) was measured and most products contained more phthalates than the regulated guidelines (a total content of 6 phthalates to be ≤0.1%). For transdermal delivery, all items were found to be lower in the NIER transdermal delivery test method compared to the US EPA Hand Wipe (stress condition and physiological condition) transdermal delivery test method. For the US EPA Hand Wipe (stress condition and physiological condition) transdermal delivery test method, a similar result was observed, except for DINP. The average daily dose (ADD) estimated by determining the exposure algorithm for each transdermal delivery test method was highest in mats with a large contacting surface area and a long exposure time in the respective test methods. Conclusively, there was a difference between the NIER transdermal delivery test method and the US EPA Wipe transdermal delivery test method.

Minimum 10-year follow-up of micro-arc oxidation coating on a cementless grit-blasted tapered-wedge stem of total hip arthroplasty: a multicentre study.

BACKGROUND: Recently, a femoral stem treated with grit-blasting and micro-arc oxidation (MAO) coating has commercialised but medium-term follow-up studies are lacking. The aim of this study was to report the outcome of a grit-blasted and MAO-coated femoral component designed as a straight, double-wedged, tapered stem with a rectangular cross-section with minimum 10 years follow-up. METHODS: Between March 2006 and December 2008, 309 primary total hip arthroplasties using a grit-blasted and MAO-coated femoral component were performed by 3 experienced hip surgeons in 3 hospitals. At minimum 10 years after index THA, 299 hips were living, 10 hips were deceased, and 65 hips were lost to follow-up or had a follow-up period <10 years. Finally, 234 hips were enrolled in this study. RESULTS: Mean duration of clinical follow-up was 129.6 months. The mean Harris Hip Score was improved from 46.9 to 88.4 at the final follow-up. 4 hips were revised for 2 aseptic femoral loosening, 1 aseptic acetabular cup loosening and 1 late infection. 3 hips were revised for a periprosthetic femoral fracture requiring a femoral component revision. The average time to revision was 51.6 (range 0-148) months. Kaplan-Meier survivorship analysis with an end point of revision for any reason demonstrated a survival rate of 97.4% at 10 years. Survival was 98.7% with revision for aseptic loosening as the endpoint. CONCLUSIONS: The outcomes of a cementless grit-blasted and MAO-coated tapered-wedge stem of THA were excellent to satisfactory after a follow-up of at least 10 years.

Lateral pillar is the key in supporting pre-collapse osteonecrosis of the femoral head: a finite element model analysis of propensity-score matched cohorts.

BACKGROUND: This study was designed as a cohort study using propensity-score matching to age, gender, and body mass index (BMI) for finite element model (FEM) analysis from pre-collapse CT images of collapsed and non-collapsed hips. Through FEM analysis, a global graphical output around the hip joint can provide simple impression of stress distribution: concentration or dispersion. METHODS: A total of 32 hips with ARCO stage 2 or 3 ONFH who were on follow up for over a one-year period were retrospectively reviewed. 16 hips with no interval progression of collapse were set as the study group, then 16 hips with progression of collapse which required arthroplasty were set as the control group using propensity-score matching. FEM was generated through Mechanical Finder for each patient, then 4500 N of load was applied to 1000 mm2 area at the top of iliac crest to analyze the models in terms of equivalents for yield stress. RESULTS: Age, sex, and BMI had no significant differences between the two groups, while location (p = 0.015) was lateral, and size (p = 0.015) was significantly greater in the collapsed group. Non-collapsed hips mostly exhibited stress dispersion allocated to medial and lateral pillars, while collapsed hips exhibited stress concentration focused on the lateral pillar and the primary compression trabecula. (p = 0.001). CONCLUSION: Through FEM analysis, stress concentration to the lateral pillar and the primary compression trabeculae can be used to predict future collapse in ONFH with high probability. Results provide a simple and intuitive, yet valuable information to aid surgeons. Therefore, especially for young patients, holding out the lateral pillar through joint preserving procedures might be the key in preventing further collapse.

Usefulness of intraoperative C-arm image intensifier in reducing errors of acetabular component during primary total hip arthroplasty: an application of Widmer's method.

BACKGROUND: Acetabular prosthesis positioning in total hip arthroplasty (THA) is crucial in reducing the risk of dislocation. There has been minimal research on the proper way to put the acetabular components into the safe zone intraoperatively. Assessment of version by intraoperative imaging intensifier is very valuable. The value of Widmer's method, using the intraoperative C-arm available to determine cup anteversion was assessed. METHODS: One hundred one hips in 91 patients who underwent primary THA were eligible for inclusion. Utilizing intraoperative C-arm images, measurement was performed using the technique described by Widmer. The values obtained using 3D computed tomography postoperatively, which determined the anteversion of the acetabular component, were regarded as the reference standard. RESULTS: The method of Widmer obtained values similar to those obtained using 3D computed tomography and was considered accurate (n.s.). All 101 hips were positioned in the set target zone. Among the 101 hips, the cup position in nine hips (8.9%) was changed. The dislocation rate in our study was 1.0% with all dislocations occurring in hips placed in the target zone. The mean Harris hip score after THA in 1 year was 94.2 (82-98). CONCLUSIONS: The method of Widmer was accurate using intraoperative imaging intensifier for the measurement of the anteversion of the acetabular component during THA, with reference to the anteversion obtained from the 3D computed tomography. Also, utilizing intraoperative C-arm imaging was very useful because it allowed for correction of the position of the acetabular cup.

Improved Biological Responses of Titanium Coating Using Laser-Aided Direct Metal Fabrication on SUS316L Stainless Steel.

Direct metal fabrication (DMF) coatings have the advantage of a more uniform porous structure and superior mechanical properties compared to coatings provided by other methods. We applied pure titanium metal powders to SUS316L stainless steel using laser-aided DMF coating technology with 3D printing. The purpose of this study was to determine the efficacy of this surface modification of stainless steel. The capacity of cells to adhere to DMF-coated SUS316L stainless steel was compared with machined SUS316L stainless steel in vitro and in vivo. Morphological in vitro response to human osteoblast cell lines was evaluated using scanning electron microscopy. Separate specimens were inserted into the medulla of distal femurs of rabbits for in vivo study. The distal femurs were harvested after 3 months, and were then subjected to push-out test and histomorphometrical analyses. The DMF group exhibited a distinct surface chemical composition, showing higher peaks of titanium compared to the machined stainless steel. The surface of the DMF group had a more distinct porous structure, which showed more extensive coverage with lamellipodia from osteoblasts than the machined surface. In the in vivo test, the DMF group showed better results than the machined group in the push-out test (3.39 vs. 1.35 MPa, respectively, p = 0.001). In the histomorphometric analyses, the mean bone-to-implant contact percentage of the DMF group was about 1.5 times greater than that of the machined group (65.4 ± 7.1% vs. 41.9 ± 5.6%, respectively; p < 0.001). The porous titanium coating on SUS316L stainless steel produced using DMF with 3D printing showed better surface characteristics and biomechanical properties than the machined SUS316L.

Long-Term Results of Total Hip Arthroplasty in Young Patients With Osteonecrosis After Allogeneic Bone Marrow Transplantation for Hematological Disease: A Multicenter, Propensity-Matched Cohort Study With a Mean 11-Year Follow-Up.

BACKGROUND: The number of young patients with hematological disease requiring total hip arthroplasty (THA) is expected to increase. We aimed to investigate the long-term THA outcomes in patients with osteonecrosis of the femoral head (ONFH) following allogeneic bone marrow transplantation (BMT) for hematological disease. METHODS: All patients who underwent THA for osteonecrosis after BMT from 1997 to 2012 were identified at 2 institutions. Using propensity scores, 75 THAs in 45 patients were matched for age, gender, body mass index, American Society of Anesthesiologists score, and year of surgery with 75 THAs in 58 patients with idiopathic ONFH without a history of hematological disease (1:1 ratio). The mean age at surgery was 36.7 years and 52% were men. Clinical and radiographic evaluations were performed and clinical scores were obtained at last follow-up. Kaplan-Meier analyses were used to compare survivorship. RESULTS: At a mean follow-up of 10.6 ± 3.5 years, clinical, radiographic, and survivorship outcomes, and the Harris hip scores were similar between both groups. The 13-year survivorship for all-cause revision was 93.4% for the BMT group and 95% for the control group (P = .928). No significant differences were observed between groups in the rates of reoperation (4% vs 5.3%, P = 1.000), 90-day readmission (all 5.3%), or overall mortality (4.4% vs 1.7%, P = .681). No hips had periprosthetic joint infection or septic loosening in either group. Osteolysis occurred in none of the BMT patients and in 2 hips (2.7%) of the control patients (P = .497). CONCLUSION: This large cohort multicenter survey at 11-year follow-up shows that contemporary cementless THA in young hematological disease patients after allogeneic BMT is not associated with a higher risk for surgical complications, revision, reoperation, readmission, and mortality compared to a matched cohort of idiopathic ONFH.

Is there a correlation between fragility fractures of the pelvis (FFP) and the morphology of the true pelvis in geriatric patients?

PURPOSE: There has been no prior study to demonstrate the relationship between the occurrence of fragility fractures of the pelvis and its morphology. The aim of this study was to investigate the effect of pelvic morphology on fragility fractures of the pelvis caused by low-energy trauma in elderly female patients. MATERIALS AND METHODS: As a normal pelvis group, 643 female patients over 65 years of age who underwent pelvic CT were collected. Using three-dimensional multiplanar reconstruction (3D-MPR) function of RadiAnt software, the DT (diameter of transverse true pelvis)/DS (diameter of sagittal true pelvis) values of normal pelvis were measured. Sorted in ascending order, the mean DT/DS value of normal pelvis was 1.13 ± 0.09. The values corresponding to the 25th percentile and the 75th percentile were 1.06 and 1.18, respectively. We arbitrarily named DT/DS values of 1.06 or less corresponding to lower than 25th percentile as 'Circle types', and DT/DS values of 1.18 or higher corresponding to higher than 75th percentile as 'Ellipse types'. Total of 76 female patients over 65 years of age who underwent 3D reconstructions of pelvic CT scans with fragility fractures of the pelvis, who fell into the criteria corresponding to FFP classification type II, were studied separately. Of the 76 female FFPs, two were FFP type IIa, 32 were FFP type IIb, and 42 were FFP type IIc. Their DT/DS was measured. RESULTS: Based on the above mentioned criteria, we classified the pelvis shape of 76 patients with fragility fracture of the pelvis type II. 33 patients (43.4%) were classified as circle types and eight patients (10.5%) were classified as ellipse types. The odds ratio of "circle type" for fragility fractures of pelvis type II was 4.1. CONCLUSION: With digital reconstruction and 3D measurement of normal adult pelvic CT scans, this study obtained a series of DT/DS values describing the shape of true pelvises. Circle-type true pelvis was found to be more common in patients with fragility fracture of the pelvis type II.

Comparative analysis of titanium coating on cobalt-chrome alloy in vitro and in vivo direct metal fabrication vs. plasma spraying.

BACKGROUND: Titanium surface coating on cobalt-chromium (CoCr) alloy has characteristics desirable for an orthopedic implant as follows: strength, osteointegrative capability, and biocompatibility. Creating such a coated surface takes a challenging process and two dissimilar metals are not easily welded. In our study, we utilized additive manufacturing with a 3D printing called direct metal fabrication (DMF) and compared it to the plasma spraying method (TPS), to coat titanium onto CoCr alloy. We hypothesized that this would yield a coated surface quality as acceptable or better than the already established method of plasma spraying. For this, we compared characteristics of titanium-coated surfaces created by direct metal fabrication method (DMF) and titanium plasma spraying (TPS), both in vitro and in vivo, for (1) cell morphology, (2) confocal microscopy images of immunofluorescent assay of RUNX2 and fibronectin, (3) quantification of cell proliferation rate, (4) push-out biomechanical test, and (5) bone histomorphometry. METHOD: For in vitro study, human osteoblast cells were seeded onto the coated surfaces. Cellular morphology was observed with a scanning electron microscope. Cellular proliferation was validated with ELISA, immunofluorescent assay. For in vivo study, coated rods were inserted into the distal femur of the rabbit and then harvested. The rods were biomechanically tested with a push-out test and observed for histomorphometry to evaluate the microscopic bone to implant ratio. RESULT: For cell morphology observation, lamellipodia and filopodia, a cytoplasmic projection extending into porous structure, formed on both surfaces created by DMF and TPS. The proliferation of the osteoblasts, the DMF group showed a better result at different optic density levels (p = 0.035, 0.005, 0.001). Expression and distribution of fibronectin and Runx-2 genes showed similar degrees of expressions. The biomechanical push-out test yielded a similar result (p = 0.714). Histomorphometry analysis also showed a similar result (p = 0.657). CONCLUSION: In conclusion, DMF is a method which can reliably create a proper titanium surface on CoCr alloy. The resulting product of the surface shows a similar quality to that of the plasma spraying method, both in vivo and in vitro, in terms of biological and mechanical property.

A New Method of Measuring the Volumetric Change of Alveolar Bone Around Dental Implants Using Computed Tomography.

This study proposes a method for measuring the volumetric change of alveolar bone after dental implant surgery using computed tomography (CT). A total of 40 implants in 20 patients (15 males and 5 females) were selected. The types of implants used were group 1: 24 CMI IS-II Active implants (Neobiotech Co., Seoul, Republic of Korea) and group 2: 16 SLActive Bone Level implants (Institut Straumann AG, Basel, Switzerland). The OnDemand3D software (CyberMed, Seoul, Korea) was used for analysis. The volumetric change of the alveolar bone around an implant fixture is measured as follows: (1) Establish two cylinders: the main cylinder with the implant axis as the central axis (radius of implant + 3 mm) and the error correction cylinder (radius of implant + 1 mm). (2) The height of the cylinder extended from the top of the fixture to a 3 mm coronal portion. (3) Calculate the volumetric change of the alveolar bone (Vd) by subtracting the volume of the error correction cylinder from the main cylinder between CT images taken immediately after the implant placement and 12 months later. After a one-year installation, the volumetric change of alveolar bone, ΔV (cc) had increased in both groups (group 1: -0.011 ± 0.015 cc, group 2: -0.012 ± 0.017 cc) with statistical significance (p < 0.05), and the difference between the groups was not statistically significant (p > 0.05). This three-dimensional assessment method would be a useful clinical reference for the assessment of marginal bone change after implant surgery.

Fourth-generation ceramic-on-ceramic THA results in improvements in midterm outcomes compared to third-generation THA but does not resolve noise problems: a cohort study of a single-hip system.

BACKGROUND: Using data from the Korean Hip Registry, we aimed to investigate mid-term clinical and radiographic outcomes, including the prevalence of periprosthetic joint infection (PJI), osteolysis, and component loosening or dislocation, and to analyze the incidence of bearing-related complications following modern ceramic-on-ceramic (COC) total hip arthroplasty (THA) using a single cementless hip system. METHODS: Four hundred eighty-two patients (602 hips) who underwent Forte or Delta COC THAs with a single hip system and had a minimum 5-year follow-up were identified. The sample included 243 (50.4%) women and 239 (49.6%) men with a mean age of 50.6 years (range: 18-83 years). The Forte group comprised 310 hips, and the Delta group comprised 292 hips. The mean follow-up was 6.1 years (range: 5-10.2 years). RESULTS: Cup orientation did not differ between groups. No hip had a PJI or osteolysis in either group. All acetabular components and all but two femoral components (in the Delta group) were well fixed. Dislocations occurred in six (1.9%) hips in the Forte group and one (0.3%) hip in the Delta group (p = 0.124). A total of nine (1.5%) revisions were performed. The 5-year survival rates for all-cause revisions were 98.4 and 98.6%, respectively. One (0.3%) ceramic head fracture occurred in the Forte group. Sixteen (5%) hips exhibited clicking and 6 (2%) hips had squeaking in the Forte group; 16 (6%) hips exhibited clicking and 5 (2%) hips had squeaking in the Delta group. Multiple regression analysis revealed that noise generation was unassociated with any factor. CONCLUSIONS: From the Korean Hip Registry data, THA with modern ceramic bearings showed encouraging results, with lower risks of PJI, osteolysis, and component loosening. In particular, Delta COC THA resulted in no PJI or ceramic fracture and had a reduced dislocation risk. However, associated noise remains a concern.