Adsorption of the herbicides diquat and difenzoquat on polyurethane foam: Kinetic, equilibrium and computational studies.

This work reports a study about the adsorption of the herbicides diquat and difenzoquat from aqueous medium employing polyurethane foam (PUF) as the adsorbent and sodium dodecylsulfate (SDS) as the counter ion. The adsorption efficiency was shown to be dependent on the concentration of SDS in solution, since the formation of an ion-associate between cationic herbicides (diquat and difenzoquat) and anionic dodecylsulfate is a fundamental step of the process. A computational study was carried out to identify the possible structure of the ion-associates that are formed in solution. They are probably formed by three units of dodecylsulfate bound to one unit of diquat, and two units of dodecylsulfate bound to one unit of difenzoquat. The results obtained also showed that 95% of both herbicides present in 45mL of a solution containing 5.5mgL-1 could be retained by 300mg of PUF. The experimental data were well adjusted to the Freundlich isotherm (r2 ≥ 0.95) and to the pseudo-second-order kinetic equation. Also, the application of Morris-Weber and Reichenberg equations indicated that an intraparticle diffusion process is active in the control of adsorption kinetics.

Polyurethane foam loaded with sodium dodecylsulfate for the extraction of 'quat' pesticides from aqueous medium: Optimization of loading conditions.

The cationic herbicides paraquat, diquat and difenzoquat are largely used in different cultures worldwide. With this, there is an intrinsic risk of environmental contamination when these herbicides achieve natural waters. The goal of this work was to propose a novel and low-cost sorbent for the removal of the cited herbicides from aqueous medium. The proposed sorbent was prepared by loading polyurethane foam with sodium dodecylsulfate. The influence of several parameters (SDS concentration, HCl concentration and shaking time) on the loading process was investigated. The results obtained in this work demonstrated that all studied variables influenced the loading process, having significant effect on the extraction efficiency of the resulted PUF-SDS. At optimized conditions, the PUF was loaded by shaking 200mg of crushed foam with 200mL of a solution containing 5.0×10(-3)molL(-1) SDS and 0.25molL(-1) HCl, for 30min. The obtained PUF-SDS was efficient for removing the three herbicides from aqueous medium, achieving extraction percentages higher than 90%. The sorption process followed a pseudo second-order kinetics, which presented excellent predictive capacity of the amount of herbicide retained with time.

Sorption of the herbicides diquat and difenzoquat from aqueous medium by polymeric resins in the presence of sodium dodecylsulfate: Kinetic and mechanistic study.

The goal of this work was to propose a novel method for the solid-phase extraction of the herbicides diquat (DQT(2+)) and difenzoquat (DFQT(+)) from aqueous medium using polymeric Amberlite XAD-2 and XAD-4 resins in the presence of sodium dodecylsulfate (SDS). The addition of SDS to the medium was of fundamental importance in order to allow the formation of a negatively charged surface able to sorb the cationic solutes. Several factors that could influence the sorption process, such as SDS concentration in the medium, sorbent mass, pH, ionic strength, and initial concentration of the solutes were investigated. Kinetic studies were also performed to model the system and to identify the mechanisms that operate the sorption process of the herbicides. SDS concentration in the medium presented remarkable influence on the extraction efficiency, achieving maximum values when the ratios [SDS]/[herbicide] were approximately 90, for XAD-2, and 22 and 11 for DQT(2+) and DFQT(+), respectively, for XAD-4. The sorption process followed a pseudo second-order kinetic in all cases studied. It was also found that an intraparticle diffusion process controlled exclusively the sorption of the herbicides by the Amberlite XAD-2 and XAD-4 resins in the first 15 min, becoming less active with time.

Sulfentrazone dechlorination by iron-nickel bimetallic nanoparticles.

The sulfentrazone dechlorination using bimetallic nanoparticles of Fe/Ni was studied. Different variables that could influence the sulfentrazone conversion were investigated, such as nitrogen atmosphere, pH and dosage of the nanoparticles and initial concentration of sulfentrazone. The best results were obtained using controlled pH (pH 4.0) and 1.0 g L(-1) of nanomaterials, resulting in 100 % conversion in only 30 min. Kinetic studies were also conducted, evaluating the influence of different nanoparticle dosages (1.0 to 4.0 g L(-1)), system temperatures (20 to 35 °C) and nickel levels in the composition of the nanomaterials (0.025 to 0.10 gNi/gFe). The mechanism of sulfentrazone conversion has changed due a direct reduction on the catalytic activity sites and indirect reduction by atomic hydrogen. Both mechanisms have followed pseudo-first order models. The conversion rate improved when the dosage of the nanomaterials, system temperature and nickel content in the composition of the nanocomposites were increased. Finally, the conversion products were elucidated by mass spectrometry and toxicity assays were performed using Daphnia Similis. The results showed that the dechlorination product is less toxic than sulfentrazone.

Modeling, kinetic, and equilibrium characterization of paraquat adsorption onto polyurethane foam using the ion-pairing technique.

We studied the adsorption of paraquat onto polyurethane foam (PUF) when it was in a medium containing sodium dodecylsulfate (SDS). The adsorption efficiency was dependent on the concentration of SDS in solution, because the formation of an ion-associate between the cationic paraquat and the dodecylsulfate anion was found to be a fundamental step in the process. A computational study was carried out to identify the possible structure of the ion-associate in aqueous medium. The obtained data demonstrated that the structure is probably formed from four units of dodecylsulfate bonded to one paraquat moiety. The results showed that 94% of the paraquat present in 45 mL of a solution containing 3.90 × 10(-5) mol L(-1) could be retained by 300 mg of PUF, resulting in the removal of 2.20 mg of paraquat. The experimental data were reasonably adjusted to the Freundlich isotherm and to the pseudo-second-order kinetic model. Also, the application of Morris-Weber and Reichenberg models indicated that both film-diffusion and intraparticle-diffusion processes were active during the control of the adsorption kinetics.

Sorption and desorption of sulfentrazone in Brazilian soils.

This study was undertaken to obtain information about the behavior of sulfentrazone in soil by evaluating the sorption and desorption of the herbicide in different Brazilian soils. Batch equilibrium method was used and the samples were analyzed by high performance liquid chromatography. Based on the results obtained from the values of Freundlich constants (Kf), we determined the order of sorption (Haplic Planosol < Red-Yellow Latosol < Red Argisol < Humic Cambisol < Regolitic Neosol) and desorption (Regolitic Neosol < Red Argisol < Humic Cambisol < Haplic Planosol < Red-Yellow Latosol) of sulfentrazone in the soils. The process of pesticide sorption in soils was dependent on the levels of organic matter and clay, while desorption was influenced by the organic matter content and soil pH. Thus, the use of sulfentrazone in soils with low clay content and organic matter (low sorption) increases the probability of contaminating future crops.

Multivariate optimization of the determination of zinc in diesel oil employing a novel extraction strategy based on emulsion breaking.

This paper describes the extraction/pre-concentration of Zn from diesel oil and its determination by Flame Atomic Absorption Spectrometry (FAAS), proposed as a novel approach for these kinds of analyses and the multivariate optimization of the proposed procedure. The extraction of Zn is based on the emulsification of an aqueous solution containing Triton X-114 and HNO(3) with diesel oil samples followed by breaking of the emulsion by heating. The aqueous phase obtained after the emulsion breaking was collected and used for Zn quantification by FAAS. The methodology was optimized using a Doehlert design and the system variables were the concentrations of surfactant and HNO(3) in the solution employed in the emulsification and the temperature used in the emulsion breaking. The ratio between absorbance and the time required to break the emulsions was taken as response. Two sets of experiments, using different emulsifier agents, were run: the first one using Triton X-100 and the second one using Triton X-114. At optimized conditions, the emulsions were prepared by mixing 10 mL of diesel oil with 2 mL of a solution containing 5% w/v of Triton X-114 and 15% v/v of HNO(3) and broken by heating at 80 °C. The proposed analytical procedure was applied in the analysis of six real samples of diesel oil and a recovery test was carried out by spiking the samples with known amounts of Zn (25 and 50 µg L(-1)), added as organometallic oiled standard. Recovery percentages achieved in this test were between 92 and 109%.

Determination of Eucalyptus spp lignin S/G ratio: a comparison between methods.

The syringyl/guaiacyl ratio was determined for six different Eucalyptus spp. wood clones cultivated in four regions in Brazil. The determinants were made by pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) and the results were compared with those obtained by alkaline nitrobenzene oxidation method. The S/G ratios were obtained considering all the identified lignin derivatives in the pyrograms and also using two groups of markers. The first group of markers consisted of guaiacol, 4-methylguaiacol, 4-vinylguaiacol, trans-isoeugenol, syringol, 4-methylsyringol, 4-vinylsyringol and trans-4-propenylsyringol compounds as markers. The second group included guaiacol, 4-methylguaiacol, 4-vinylguaiacol, vanillin, 4-ethylsyringol, 4-vinylsyringol, syringaldehyde, syringylacetone and trans-4-propenylsyringol. It was observed from the statistical analysis that the values of S/G obtained by Py-GC-MS using the two groups of markers did not differ significantly from those obtained by nitrobenzene oxidation method.

Dependency structure matrix, genetic algorithms, and effective recombination.

Abstract In many different fields, researchers are often confronted by problems arising from complex systems. Simple heuristics or even enumeration works quite well on small and easy problems; however, to efficiently solve large and difficult problems, proper decomposition is the key. In this paper, investigating and analyzing interactions between components of complex systems shed some light on problem decomposition. By recognizing three bare-bones interactions-modularity, hierarchy, and overlap, facet-wise models are developed to dissect and inspect problem decomposition in the context of genetic algorithms. The proposed genetic algorithm design utilizes a matrix representation of an interaction graph to analyze and explicitly decompose the problem. The results from this paper should benefit research both technically and scientifically. Technically, this paper develops an automated dependency structure matrix clustering technique and utilizes it to design a model-building genetic algorithm that learns and delivers the problem structure. Scientifically, the explicit interaction model describes the problem structure very well and helps researchers gain important insights through the explicitness of the procedure.