Comparison of Eleven Heavy Metals in Moringa Oleifera Lam. Products.

Eleven heavy metals in various products of Moringa oleifera were analyzed to determine eleven heavy metals (Al, As, Cd, Cr, Cu, Fe, Pb, Mn, Hg, Ni, and Zn) using Inductively Coupled Plasma-Mass Spectrometry. The products of M. oleifera were purchased in Nakhon Pathom, Thailand. All products were digested with nitric acid solution before determining the concentrations of heavy metals. The recoveries of all heavy metals were found to be in the range of 99.89-103.05%. Several criteria such as linearity, limits of detection, limits of quantification, specificity, precision under repeatability conditions and intermediate precision reproducibility were evaluated. Results indicate that this method could be used in the laboratory for determination of eleven heavy metals in M. oleifera products with acceptable analytical performance. The results of analysis showed that the highest concentrations of As, Cr, Hg, and Mn were found in tea leaves while the highest concentrations of Al, Cd, Cu, Fe, Ni, Pb, and Zn were found in leaf capsules. Continuous monitoring of heavy metals in M. oleifera products is crucial for consumer health.

Use of spray-dried chitosan acetate and ethylcellulose as compression coats for colonic drug delivery: effect of swelling on triggering in vitro drug release.

Spray-dried chitosan acetate (CSA) and ethylcellulose (EC) were used as new compression coats for 5-aminosalicylic acid tablets. Constrained axial or radial swelling of pure CSA and EC/CSA tablets in 0.1 N HCl (stage I), Tris-HCl, pH 6.8 (stage II), and acetate buffer, pH 5.0 (stage III), was investigated. Factors affecting in vitro drug release, i.e., % weight ratios of coating polymers, dip speeds of dissolution apparatus or pH of medium or colonic enzyme (beta-glucosidase) in stage III, and use of a super disintegrant in core tablets, were evaluated. Swollen CSA gel dissolved at lower pH and became less soluble at higher pH. The mechanism of swelling was Fickian diffusion fitting well into both Higuchi's and Korsmeyer-Peppas models. EC:CSA, at 87.5:12.5% weight ratio, provided lag time rendering the tablets to reach stage III (simulated colonic fluid of patients), and the drug was released over 90% within 12 h. The system was a dual time- and pH-control due to the insolubility of EC suppressing water diffusion and the swelling of CSA in the stages I and II. The erosion of CSA gel in the stage III induced the disintegration of the coat resulting in rapid drug release. The lower dip speed and higher pH medium delayed the drug release, while a super disintegrant in the cores enhanced the drug release and no enzyme effect was observed.

Effect of chitosan salts and molecular weight on a nanoparticulate carrier for therapeutic protein.

The objective of this study was to investigate the potential of chitosan salts as a carrier in the preparation of protein-loaded nanoparticles. Glutamic and aspartic acids were used to prepare chitosan salts of 35, 100, and 800 KDa. Nanoparticles of chitosan base, chitosan glutamate, and chitosan aspartate were produced by ionotropic gelation with sodium tripolyphosphate (TPP). Bovine serum albumin (BSA) was applied as a model protein at loading concentrations ranging from 0.2 to 2 mg/mL. The size of the nanoparticles, as measured by photon correlation spectroscopy, was in the range of 195 to 3450 nm, depending on type and molecular weight of chitosan. Nanoparticles prepared with higher molecular weight chitosan showed larger sizes. The encapsulation was controlled by the competition of BSA in forming ionic cross-linking with chitosan and by the entrapment of BSA during the gelation process. Higher BSA encapsulation efficiency (EE) was obtained for nanoparticles prepared with chitosan salts compared to those prepared with the base. The higher EE was a result of a higher degree of ionization, causing more active sites to interact with BSA. In addition, a higher and faster release of BSA from the nanoparticles into pH 7.4 buffer medium was observed for nanoparticles of the chitosan salts than was observed for nanoparticles of the chitosan base. The higher and faster release was attributed to higher EE and lower entrapment of BSA within the matrix of the nanoparticle during the gelation process. The influence of molecular weight on the property of nanoparticles exhibited different effects. The difference was a result of different organic acids used to prepare nanoparticles leading to the difference in polymer conformation and viscosity of organic acid solution. Therefore, this study showed that the characteristics of chitosan nanoparticles loaded with a protein drug could be readily modulated by changing the salt form or the molecular weight of the chitosan carrier.

Characterization of chitosan acetate as a binder for sustained release tablets.

A chitosan derivative as an acetate salt was successfully prepared by using a spray drying technique. Physicochemical characteristics and micromeritic properties of spray-dried chitosan acetate (SD-CSA) were studied as well as drug-polymer and excipient-polymer interaction. SD-CSA was spherical agglomerates with rough surface and less than 75 microm in diameter. The salt was an amorphous solid with slight to moderate hygroscopicity. The results of Fourier transform infrared (FTIR) and solid-state (13)C NMR spectroscopy demonstrated the functional groups of an acetate salt in its molecular structure. DSC and TGA thermograms of SD-CSA as well as FTIR and NMR spectrum of the salt, heated at 120 degrees C for 12 h, revealed the evidence of the conversion of chitosan acetate molecular structure to N-acetylglucosamine at higher temperature. No interaction of SD-CSA with either drugs (salicylic acid and theophylline) or selected pharmaceutical excipients were observed in the study using DSC method. As a wet granulation binder, SD-CSA gave theophylline granules with good flowability (according to the value of angle of repose, Carr's index, and Hausner ratio) and an excellent compressibility profile comparable to a pharmaceutical binder, PVP K30. In vitro release study of theophylline from the tablets containing 3% w/w SD-CSA as a binder demonstrated sustained drug release in all media. Cumulative drug released in 0.1 N HCl, pH 6.8 phosphate buffer and distilled water was nearly 100% within 6, 16 and 24 h, respectively. It was suggested that the simple incorporation of spray-dried chitosan acetate as a tablet binder could give rise to controlled drug delivery systems exhibiting sustained drug release.