Hip joint center lateralization minimally affects the biomechanics of patient-specific flanged acetabular components: A computational model.

Patient-specific flanged acetabular components are utilized to treat failed total hip arthroplasties with large acetabular defects. Previous clinical studies from our institution showed that these implants tend to lateralize the acetabular center of rotation. However, the clinical impact of lateralization on implant survivorship is debated. Our goal was to develop a finite element model to quantify how lateralization of the native hip center affects periprosthetic strain and implant-bone micromotion distributions in a static level gait loading condition. To build the model, we computationally created a superomedial acetabular defect in a computed tomography 3D reconstruction of a native pelvis and designed a flanged acetabular implant to address this simulated bone defect. We modeled two implants, one with ~1 cm and a second with ~2 cm of hip center lateralization. We applied the maximum hip contact force and corresponding abductor force observed during level gait. The resulting strains were compared to bone fatigue strength (0.3% strain) and the micromotions were compared to the threshold for bone ingrowth (20 µm). Overall, the model demonstrated that the additional lateralization only slightly increased the area of bone at risk of failure and decreased the areas compatible with bone ingrowth. This computational study of patient-specific acetabular implants establishes the utility of our modeling approach. Further refinement will yield a model that can explore a multitude of variables and could be used to develop a biomechanically-based acetabular bone loss classification system to guide the development of patient-specific implants in the treatment of large acetabular bone defects.

Is Tibial Bone Mineral Density Related to Sex, Age, Preoperative Alignment, or Fixation Method in Primary Total Knee Arthroplasty?

BACKGROUND: Cementless total knee arthroplasty (TKA) has regained interest for its potential for long-term biologic fixation. The density of the bone is related to its ability to resist static and cyclic loading and can affect long-term implant fixation; however, little is known about the density distribution of periarticular bone in TKA patients. Thus, we sought to characterize the bone mineral density (BMD) of the proximal tibia in TKA patients. METHODS: We included 42 women and 50 men (mean age 63 years, range: 50 to 87; mean body mass index 31.6, range: 20.5 to 49.1) who underwent robotic-assisted TKA and had preoperative computed tomography scans with a BMD calibration phantom. Using the robotic surgical plan, we computed the BMD distribution at 1 mm-spaced cross-sections parallel to the tibial cut from 2 mm above the cut to 10 mm below. The BMD was analyzed with respect to patient sex, age, preoperative alignment, and type of fixation. RESULTS: The BMD decreased from proximal to distal. The greatest changes occurred within ± 2 mm of the tibial cut. Age did not affect BMD for men; however, women between 60 and 70 years had higher BMD than women ≥ 70 years for the total cut (P = .03) and the medial half of the cut (P = .03). Cemented implants were used in 1 86-year-old man and 18 women (seven < 60 years, seven 60 to 70 years, and four ≥ 70 year old). We found only BMD differences between cemented or cementless fixation for women < 60 years. CONCLUSIONS: To our knowledge, this is the first study to characterize the preoperative BMD distribution in TKA patients relative to the intraoperative tibial cut. Our results indicate that while sex and age may be useful surrogates of BMD, the clinically relevant thresholds for cementless knees remain unclear, offering an area for future studies.

A novel computational workflow to holistically assess total knee arthroplasty biomechanics identifies subject-specific effects of joint mechanics on implant fixation.

Computational studies of total knee arthroplasty (TKA) often focus on either joint mechanics (kinematics and forces) or implant fixation mechanics. However, such disconnect between joint and fixation mechanics hinders our understanding of overall TKA biomechanical function by preventing identification of key relationships between these two levels of TKA mechanics. We developed a computational workflow to holistically assess TKA biomechanics by integrating musculoskeletal and finite element (FE) models. For our initial study using the workflow, we investigated how tibiofemoral contact mechanics affected the risk of failure due to debonding at the implant-cement interface using the four available subjects from the Grand Challenge Competitions to Predict In Vivo Knee Loads. We used a musculoskeletal model with a 12 degrees-of-freedom knee joint to simulate the stance phase of gait for each subject. The computed tibiofemoral joint forces at each node in contact were direct inputs to FE simulations of the same subjects. We found that the peak risk of failure did not coincide with the peak joint forces or the extreme tibiofemoral contact positions. Moreover, despite the consistency of joint forces across subjects, we observed important variability in the profile of the risk of failure during gait. Thus, by a combined evaluation of the joint and implant fixation mechanics of TKA, we could identify subject-specific effects of joint kinematics and forces on implant fixation that would otherwise have gone unnoticed. We intend to apply our workflow to evaluate the impact of implant alignment and design on TKA biomechanics.

An Anterior Spike Decreases Bone-Implant Micromotion in Cementless Tibial Baseplates for Total Knee Arthroplasty: A Biomechanical Study.

BACKGROUND: Cementless tibial baseplates in total knee arthroplasty include fixation features (eg, pegs, spikes, and keels) to ensure sufficient primary bone-implant stability. While the design of these features plays a fundamental role in biologic fixation, the effectiveness of anterior spikes in reducing bone-implant micromotion remains unclear. Therefore, we asked: Can an anterior spike reduce the bone-implant micromotion of cementless tibial implants? METHODS: We performed computational finite element analyses on 13 tibiae using the computed tomography scans of patients scheduled for primary total knee arthroplasty. The tibiae were virtually implanted with a cementless tibial baseplate with 2 designs of fixation of the baseplate: 2 pegs and 2 pegs with an anterior spike. We compared the bone-implant micromotion under the most demanding loads from stair ascent between both designs. RESULTS: Both fixation designs had peak micromotion at the anterior-lateral edge of the baseplate. The design with 2 pegs and an anterior spike had up to 15% lower peak micromotion and up to 14% more baseplate area with micromotions below the most conservative threshold for ingrowth, 20 µm, than the design with only 2 pegs. The greatest benefit of adding an anterior spike occurred for subjects who had the smallest area of tibial bone below the 20 µm threshold (ie, most at risk for failure to achieve bone ingrowth). CONCLUSIONS: An anteriorly placed spike for cementless tibial baseplates with 2 pegs can help decrease the bone-implant micromotion during stair ascent, especially for subjects with increased bone-implant micromotion and risk for bone ingrowth failure.

Undersizing the Tibial Baseplate in Cementless Total Knee Arthroplasty has Only a Small Impact on Bone-Implant Interaction: A Finite Element Biomechanical Study.

BACKGROUND: The tibial component in total knee arthroplasty (TKA) is often chosen to maximize coverage of the tibial cut, which can result in excessive internal rotation of the component. Optimal rotational alignment may require a smaller baseplate with suboptimal coverage that could threaten fixation. We asked: "does undersizing the tibial component of a cementless TKA to gain external rotation increase the risk of bone failure?" METHODS: We developed computational finite element (FE) analysis models from the computed tomography (CT) scans of 12 patients scheduled for primary TKA. The models were implanted with a cementless tibial baseplate that maximized coverage and one or two sizes smaller and externally rotated by 5°. We calculated the risk of bone collapse under loads representative of stair ascent. RESULTS: Undersizing the implant increased the area at risk of collapse for eight patients. However, the area at risk of collapse for the undersized implant (range, 5.2%-16.4%) was no different (P = .24) to the optimally sized implant (range, 4.5%-17.9%). The bone at risk of collapse was concentrated along the posterior edge of the implant. The area at risk of collapse was not proportional to implant size, and for four subjects undersizing the implant actually decreased the area at risk of collapse. CONCLUSION: While implants should maximize coverage of the tibial cut and seek support on dense bone, undersizing the tibial component to gain external rotation had minimal impact on the load transfer to the underlying bone. This FE analysis model of a cementless tibial baseplate may require further validation and additional studies to investigate the long-term biomechanical effects of undersizing the tibial baseplate. In conclusion, while surgeons should strive to use the appropriate tibial baseplate for each patient, our model identified only minor biomechanical consequences of undersizing the implant for the immediate postoperative bone-implant interaction and implant subsidence.

Effect of varus alignment on the bone-implant interaction of a cementless tibial baseplate during gait.

Component alignment in total knee arthroplasty is a determining factor for implant longevity. Mechanical alignment, which provides balanced load transfer, is the most common alignment strategy. However, a retrospective review found that varus alignment, which could lead to unbalanced loading, can happen in up to 18% of tibial baseplates. This may be particularly burdensome for cementless tibial baseplates, which require low bone-implant micromotion and avoidance of bone overload to obtain bone ingrowth. Our aim was to assess the effect of varus alignment on the bone-implant interaction of cementless baseplates. We virtually implanted 11 patients with knee OA with a modern cementless tibial baseplate in mechanical alignment and in 2° of tibial varus alignment. We performed finite element simulations throughout gait, with loading conditions derived from literature. Throughout the stance phase, varus alignment had greater micromotion and percentage of bone volume at risk of failure than mechanical alignment. At mid-stance, when the most critical conditions occurred, the average increase in peak micromotion and amount of bone at risk of failure due to varus alignment were 79% and 59%, respectively. Varus alignment also resulted in the decrease of the surface area with micromotion compatible with bone ingrowth. However, for both alignments, this surface area was larger than the average area of ingrowth reported for well-fixed implants retrieved post-mortem. Our findings suggest that small varus deviations from mechanical alignment can adversely impact the biomechanics of the bone-implant interaction for cementless tibial baseplates during gait; however, the clinical implications of such changes remain unclear.

Do Metaphyseal Cones and Stems Provide Any Biomechanical Advantage for Moderate Contained Tibial Defects in Revision TKA? A Finite-Element Analysis Based on a Cadaver Model.

BACKGROUND: Satisfactory management of bone defects is important to achieve an adequate reconstruction in revision TKA. Metaphyseal cones to address such defects in the proximal tibia are increasingly being used; however, the biomechanical superiority of cones over traditional techniques like fully cementing the implant into the defect has not yet been demonstrated. Moreover, although long stems are often used to bypass the defects, the biomechanical efficacy of long stems compared with short, cemented stems when combined with metaphyseal cones remains unclear. QUESTIONS/PURPOSES: We developed and validated finite-element models of nine cadaveric specimens to determine: (1) whether using cones for addressing moderate metaphyseal tibial defects in revision TKA reduces the risk of implant-cement debonding compared with cementing the implant alone, and (2) when using metaphyseal cones, whether long, uncemented stems (or diaphyseal-engaging stems) reduce the risk of implant-cement debonding and the cone-bone micromotions compared with short, cemented stems. METHODS: We divided nine cadaveric specimens (six male, three female, aged 57 to 73 years, BMI 24 to 47 kg/m2) with standardized tibial metaphyseal defects into three study groups: no cone with short (50-mm) cemented stem, in which the defect was filled with cement; cone with short (50-mm) cemented stem, in which a metaphyseal cone was implanted before cementing the implant; and cone with long, diaphyseal-engaging stem, which received a metaphyseal cone and the largest 150-mm stem that could fit the diaphyseal canal. The specimens were implanted and mechanically tested. Then, we developed and validated finite-element models to investigate the interaction between the implant and the bone during the demanding activity of stair ascent. We quantified the risk of implant debonding from the cement mantle by comparing the axial and shear stress at the cement-implant interface against an experimentally derived interface failure index criterion that has been previously used to quantify the risk of cement debonding. We considered the risk of debonding to be minimal when the failure index was below 10% of the strength of the interface (or failure index < 0.1). We also quantified the micromotion between the cone and the bone, as a guide to the likelihood of fixation by bone ingrowth. To this end, we assumed bone ingrowth for micromotion values below the most restrictive reported threshold for bone ingrowth, 20 µm. RESULTS: When using a short, 50-mm cemented stem and cement alone to fill the defect, 77% to 86% of the cement-implant interface had minimal risk of debonding (failure index < 0.1). When using a short, 50-mm cemented stem with a cone, 87% to 93% of the cement-implant interface had minimal debonding risk. When combining a cone with a long (150-mm) uncemented stem, 92% to 94% of the cement-implant interface had minimal debonding risk. The differences in cone-bone micromotion between short, cemented stems and long, uncemented stems were minimal and, for both configurations, most cones had micromotions below the most restrictive 20-µm threshold for ingrowth. However, the maximum micromotion between the cone and the bone was in general smaller when using a long, uncemented stem (13-23 µm) than when using a short, cemented stem (11-31 µm). CONCLUSION: Although the risk of debonding was low in all cases, metaphyseal cones help reduce the biomechanical burden on the implant-cement interface of short-stemmed implants in high-demand activities such as stair ascent. When using cones in revision TKA, long, diaphyseal-engaging stems did not provide a clear biomechanical advantage over short stems. Future studies should explore additional loading conditions, quantify the interspecimen variability, consider more critical defects, and evaluate the behavior of the reconstructive techniques under repetitive loads. CLINICAL RELEVANCE: Cones and stems are routinely used to address tibial defects in revision TKA. Despite our finding that metaphyseal cones may help reduce the risk of implant-cement debonding and allow using shorter stems with comparable biomechanical behavior to longer stems, either cones or cement alone can provide comparable results in contained metaphyseal defects. However, longer term clinical studies are needed to compare these techniques over time.

Treatment of Recurrent Dislocation after Total Hip Arthroplasty Using Advanced Imaging and Three-Dimensional Modeling Techniques: A Case Series.

BACKGROUND: Surgical treatment options for addressing recurrent dislocation after total hip arthroplasty (THA) vary. Identifying impingement mechanisms in an unstable THA may be beneficial in determining appropriate treatment. QUESTIONS/PURPOSES: We sought to assess the effectiveness of developing pre-operative plans for treating hip instability after THA. We used advanced imaging and three-dimensional modeling techniques to perform impingement analyses in patients with unstable THA. METHODS: We evaluated a series of eight patients who would require revision THA to treat recurrent dislocation. Using a pre-operative algorithmic approach, we built patient-specific models and evaluated hip range of motion with computed tomographic scanning and biplanar radiography. This information was used to determine a surgical treatment plan that was then executed intra-operatively. Patients were followed for 2 years to determine whether they experienced another hip dislocation following treatment. RESULTS: Pre-operative kinematic modeling showed four of the eight patients had limited hip range of motion during flexion and internal rotation; a prominent anterior inferior iliac spine (AIIS) was found to limit hip range of motion in some of these cases. In the other four patients, range of motion was acceptable, suggesting soft-tissue causes of dislocation. No patients in this series experienced dislocation after undergoing revision THA. CONCLUSION: Advanced modeling techniques may be useful for identifying the impingement mechanisms responsible for instability after THA. Once variables contributing to limited hip range of motion are identified, surgeons can develop treatment plans to improve patient outcomes. Resecting a hypertrophic AIIS may improve hip range of motion and may be an important consideration for hip surgeons when revising unstable THAs.

Biplanar Low-Dose Radiography Is Accurate for Measuring Combined Anteversion After Total Hip Arthroplasty.

BACKGROUND: Acetabular component position alone has not been predictive of stability after total hip arthroplasty (THA). Combined anteversion of the acetabulum and femur has the potential of being more predictive of stability. Unfortunately, femoral component position is difficult to measure on plain radiographs. Computed tomography (CT) is the gold standard for measuring implant position post-operatively, but CT exposes patients to a substantial amount of radiation. QUESTIONS/PURPOSES: We sought to determine whether biplanar low-dose radiography can be used to accurately measure both acetabular and femoral implant position after THA. METHODS: Twenty patients underwent standing low-dose biplanar spine-to-ankle radiographs and supine CT scans 6 weeks after THA. Measurements of acetabular inclination, acetabular anteversion, and femoral anteversion were performed by two blinded observers and compared. RESULTS: The average absolute differences between biplanar radiographs and CT scans were 2° ± 2° for acetabular inclination, 3° ± 2° for acetabular anteversion, and 4° ± 4° for femoral anteversion between EOS measurements and CT measurements. Interobserver agreement was good for acetabular inclination, acetabular anteversion, and femoral anteversion (Cronbach's α = 0.90) using biplanar low-dose imaging. CONCLUSION: Biplanar radiography is a reliable low-radiation alternative for measuring acetabular inclination, acetabular anteversion, femoral version, and thus combined anteversion compared to CT. Femoral anteversion had the most variability but is still clinically relevant.

Mechanical performance of cementless total knee replacements: It is not all about the maximum loads.

Finite element (FE) models are frequently used to assess mechanical interactions between orthopedic implants and surrounding bone. However, FE studies are often limited by the small number of bones that are modeled; the use of normal bones that do not reflect the altered bone density distributions that result from osteoarthritis (OA); and the application of simplified load cases usually based on peak forces and without consideration of tibiofemoral kinematics. To overcome these limitations, we undertook an integrated approach to determine the most critical scenario for the interaction between an uncemented tibial component and surrounding proximal tibial bone. A cementless component, based on a modern design, was virtually implanted using computed-tomography scans from 13 patients with knee OA. FE simulations were performed across a demanding activity, stair ascent, by combining in vivo experimental forces from the literature with tibiofemoral kinematics measured from patients who had received the same design of knee component. The worst conditions for the bone-implant interaction, in terms of micromotion and percentage of interfacial bone mass at risk of failure, did not arise from the maximum applied loads. We also found large variability among bones and tibiofemoral kinematics sets. Our results suggest that future FE studies should not focus solely on peak loads as this approach does not consistently correlate to worst-case scenarios. Moreover, multiple load cases and multiple bones should be considered to best reflect variations in tibiofemoral kinematics, anatomy, and tissue properties. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 37:350-357, 2019.

The Use of Three-Dimensional Printing for Complex Scaphoid Fractures.

Scaphoid fractures are one of the most common fractures treated by hand surgeons. The complex anatomy and size of the scaphoid bone can make the reduction and fixation of these fractures technically challenging. Careful preoperative planning is required to ensure stable fixation is achieved. We report on the use of 3-dimensional printing to improve preoperative planning for a series of complex scaphoid fractures.

Variable Bone Density of Scaphoid: Importance of Subchondral Screw Placement.

Background Ideal internal fixation of the scaphoid relies on adequate bone stock for screw purchase; so, knowledge of regional bone density of the scaphoid is crucial. Questions/Purpose The purpose of this study was to evaluate regional variations in scaphoid bone density. Materials and Methods Three-dimensional CT models of fractured scaphoids were created and sectioned into proximal/distal segments and then into quadrants (volar/dorsal/radial/ulnar). Concentric shells in the proximal and distal pole were constructed in 2-mm increments moving from exterior to interior. Bone density was measured in Hounsfield units (HU). Results Bone density of the distal scaphoid (453.2 ± 70.8 HU) was less than the proximal scaphoid (619.8 ± 124.2 HU). There was no difference in bone density between the four quadrants in either pole. In both the poles, the first subchondral shell was the densest. In both the proximal and distal poles, bone density decreased significantly in all three deeper shells. Conclusion The proximal scaphoid had a greater density than the distal scaphoid. Within the poles, there was no difference in bone density between the quadrants. The subchondral 2-mm shell had the greatest density. Bone density dropped off significantly between the first and second shell in both the proximal and distal scaphoids. Clinical Relevance In scaphoid fracture ORIF, optimal screw placement engages the subchondral 2-mm shell, especially in the distal pole, which has an overall lower bone density, and the second shell has only two-third the density of the first shell.

Fixed-bearing medial unicompartmental knee arthroplasty restores neither the medial pivoting behavior nor the ligament forces of the intact knee in passive flexion.

Medial unicompartmental knee arthroplasty (UKA) is an accepted treatment for isolated medial osteoarthritis. However, using an improper thickness for the tibial component may contribute to early failure of the prosthesis or disease progression in the unreplaced lateral compartment. Little is known of the effect of insert thickness on both knee kinematics and ligament forces. Therefore, a computational model of the tibiofemoral joint was used to determine how non-conforming, fixed bearing medial UKA affects tibiofemoral kinematics, and tension in the medial collateral ligament (MCL) and the anterior cruciate ligament (ACL) during passive knee flexion. Fixed bearing medial UKA could not maintain the medial pivoting that occurred in the intact knee from 0° to 30° of passive flexion. Abnormal anterior-posterior (AP) translations of the femoral condyles relative to the tibia delayed coupled internal tibial rotation, which occurred in the intact knee from 0° to 30° of flexion, but occurred from 30° to 90° of flexion following UKA. Increasing or decreasing tibial insert thickness following medial UKA also failed to restore the medial pivoting behavior of the intact knee despite modulating MCL and ACL forces. Reduced AP constraint in non-conforming medial UKA relative to the intact knee leads to abnormal condylar translations regardless of insert thickness even with intact cruciate and collateral ligaments. This finding suggests that the conformity of the medial compartment as driven by the medial meniscus and articular morphology plays an important role in controlling AP condylar translations in the intact tibiofemoral joint during passive flexion. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1868-1875, 2018.

Effect of Screw Perpendicularity on Compression in Scaphoid Waist Fractures.

Background Central and perpendicular (PERP) screw orientations have each been described for scaphoid fracture fixation. It is unclear, however, which orientation produces greater compression. Questions/Purposes This study compares compression in scaphoid waist fractures with screw fixation in both PERP and pole-to-pole (PTP) configurations. PERP orientation was hypothesized to produce greater compression than PTP orientation. Methods Ten preoperative computed tomography scans of scaphoid waist fractures were classified by fracture type and orientation in the coronal and sagittal planes. Three-dimensional models of each scaphoid and fracture plane were created. Simulated Acutrak 2 (Acumed, Hillsboro, OR) screws were placed into the models in both PERP and PTP orientations. Engagement length and screw angle relative to the fracture were measured. Compression strength was calculated from the shear area, average density, and angle acuity. Results The PTP angle between screw and fracture ranged from 36 to 84 degrees. By definition, the PERP screw-to-fracture angle was 90 degrees. Perpendicularity of the PTP screw to the fracture was positively correlated to compression strength. PERP screws had greater compression than PTP screws when the PTP screw-to-fracture angle was < 80 degrees (106 vs. 80 N), but there was no difference in compression when the PTP screw-to-fracture angle was > 80 degrees, approximating the PERP screw. Conclusion Increasing screw perpendicularity resulted in higher compression when the screw-to-fracture angle of the PTP screw was < 80 degrees. Maximum compression was obtained with a screw PERP to the fracture. The increased compression gained from PERP screw placement offsets the decreased engagement length. Clinical Relevance These results provide guidelines for optimal screw placement in scaphoid waist fractures.

A Comparison Between Chinese and Caucasian 3-Dimensional Bony Morphometry in Presimulated and Postsimulated Osteotomy for Total Knee Arthroplasty.

BACKGROUND: The bone morphologies of intact knees were measured and compared between Chinese and Caucasian populations. However, to assess if distinct designs of implants are necessary for the Chinese population owing to different morphologies and sizes, the knee measurements after osteotomy performed in total knee arthroplasty were evaluated. METHODS: Thirty-seven Caucasian and 50 Chinese patients' knees were examined using computed tomography scans. Mimics were applied to reconstruct 3-dimensional bone models. Dimensions of the 3-dimensional knee models and simulated bone resections during total knee arthroplasty were measured using Geomagic Studio and Pro/ENGINEER. The morphologic measurements of the native and resected femur and tibia included the anteroposterior (AP) depth, mediolateral (ML) width, notch width, knee physical valgus angle, tibial slope angle, and the ML-to-AP ratio of the femur, tibia, and resected femur. Statistical analysis was performed using the independent samples t test and the Pearson correlation coefficient in SPSS for Windows. Values of P < .05 were considered significant. RESULTS: No measurements were significantly different between the Chinese and Caucasian knees. However, the Chinese female showed significant differences compared with the Chinese male on distal femoral measurements both presimulated and postsimulated osteotomy such as a smaller mean ML-to-AP ratio in presimulated (1.3 ± 0.1) and postsimulated (1.3 ± 0.1) osteotomy. CONCLUSION: The necessity of designing a full set of total knee components specifically for the Chinese population is still undetermined. However, we suggest designing femoral components specific for the Chinese females because of different postosteotomy distal femoral ML-to-AP ratio between the Chinese males and the Chinese females.

Retrieval and radiographic analysis of the Contour antiprotrusio cage.

INTRODUCTION: Acetabular reconstruction in the setting of severe bone loss or pelvic discontinuity remains a challenging problem. Multiple methods of treatment have been described including antiprotrusio cages (APCs). The objective of this study is to combine biomechanical analysis of retrieved APCs with radiographic and clinical data to determine which factors influence or predict APC failure. METHODS: 41 APCs were identified. Sequential radiographs were examined for cage and polyethylene cup abduction angles, change in centre of rotation, screw placement, progression of cage failure, and failure mechanism. Cages were manually examined for gross macroscopic findings, breakage, and the location of breakage. High-resolution microscopy was used for further analysis. RESULTS: 24 cages were included in the analysis. Mean age of patients was 64.5 years (range 43-85 years); average length of implantation was 42.5 months (range 3-108 months). Average cage abduction angles were 56°; abduction for the cemented polyethylene cup was 44°. 14 of 24 cages were broken; 10 were intact. Of the broken cages, 10/14 broke through a screw hole in the ischial flange or just superior to the ischial flange. In the intact group, 6/10 failed due to pullout of the ischial screws. DISCUSSION: All cages had superior and lateralised centres of rotation. The majority of cages failed due to breakage or pullout at the ischial flange. Pelvic discontinuity was a large risk factor for a broken cage. Future design and technique modifications may result in superior outcomes in these complex acetabular reconstructions.

The ACL Graft Has Different Cross-sectional Dimensions Compared With the Native ACL: Implications for Graft Impingement.

BACKGROUND: Impingement of anterior cruciate ligament (ACL) grafts against the femoral notch and the posterior cruciate ligament (PCL) is thought to be influenced primarily by tunnel position and graft orientation. Recent data have implied that the native ACL is ribbon-shaped. PURPOSE: To evaluate the 3-dimensional shape and cross-sectional area of the native ACL versus the ACL graft and to compare the degree of impingement against the femoral notch and PCL. STUDY DESIGN: Cross-sectional study; Level of evidence, 3. METHODS: Bilateral knee magnetic resonance images were analyzed for 27 patients with unilateral bone-patellar tendon-bone (BPTB) ACL reconstruction performed via transtibial or anteromedial portal femoral tunneling techniques. Three-dimensional models of the ACL, PCL, femur, and tibia were digitally rendered. The cross-sectional area and dimensions of the native ACL and the reconstructed graft were determined at 3 equally spaced locations and compared via Wilcoxon-Mann-Whitney and Kruskal-Wallis tests. In addition, impingement of the ACL on the PCL and femoral notch was graded in 3 groups. Chi-square or Fisher exact tests were used to compare the proportional differences of impingement of the native and reconstructed ACL on the PCL and femoral notch, respectively. All analyses were performed using 2-sided hypothesis testing, with statistical significance at P < .05. RESULTS: Cross-sectional areas at all 3 points on the ACL graft were significantly greater than those of the native ACL (P < .001). The long- to short-axis ratio for the native ACL was significantly greater at each location compared with the corresponding locations along the ACL graft (P < .001), implying that the native ACL is "flatter" than is an ACL graft. There were 19 operated knees (70%) with contact or impingement between the ACL graft and the femoral notch compared with zero knees with a native ACL (P < .001). In addition, 22 operated knees (81%) showed contact or impingement between the ACL graft and the PCL, compared with 7 knees (26%) with a native ACL (P < .001). No significant differences in impingement frequency were noted between the transtibial and anteromedial tunneling techniques for ACL graft specimens (P > .05). CONCLUSION: Native ACLs have a smaller cross-sectional area, are "flatter," and experience less incidence of impingement compared with anatomically placed BPTB ACL grafts.

MRI of Polyethylene Tibial Inserts in Total Knee Arthroplasty: Normal and Abnormal Appearances.

OBJECTIVE: The purpose of this study was to describe the normal and abnormal MRI appearances of polyethylene tibial inserts. Subjects who underwent MRI before revision total knee arthroplasty were identified. The polyethylene tibial insert's shape was categorized on MRI, and the presence of abnormalities was noted. CONCLUSION: The shape of the polyethylene tibial insert varied with the design. Polyethylene tibial insert abnormalities seen on MRI included displacement and fracture. MRI distinguishes various designs of polyethylene tibial inserts and can show associated abnormalities.

A novel method to measure femoral component migration by computed tomography: a cadaver study.

INTRODUCTION: Radiostereometric analysis (RSA) is the most accurate technique to measure implant migration. However, it requires special equipment, technical expertise and analysis software and has not gained wide acceptance. The current paper analyzes a novel method to measure implant migration utilizing widely available computer tomography (CT). METHODS: Three uncemented total hip replacements were performed in three human cadavers and six tantalum beads were inserted into the femoral bone similar to RSA. Six different 28 mm heads (-3, 0, 2.5, 5.0, 7.5 and 10 mm) were added to simulate five reproducible translations (maximum total point migration) of the center of the head. Implant migration was measured in a 3-D analysis software (Geomagic Studio 7). Repeat manual reconstructions of the center of the head were performed by two investigators to determine repeatability and accuracy. RESULTS: The accuracy of measurements between the centers of two head sizes was 0.11 mm with a CI 95 % of 0.22 mm. The intra-observer repeatability was 0.13 mm (CI 95 % 0.25 mm). The interrater-reliability was 0.943. CONCLUSION: CT based measurement of head displacement in a cadaver model were highly accurate and reproducible.

A Multibody Knee Model Corroborates Subject-Specific Experimental Measurements of Low Ligament Forces and Kinematic Coupling During Passive Flexion.

A multibody model of the knee was developed and the predicted ligament forces and kinematics during passive flexion corroborated subject-specific measurements obtained from a human cadaveric knee that was tested using a robotic manipulator. The model incorporated a novel strategy to estimate the slack length of ligament fibers based on experimentally measured ligament forces at full extension and included multifiber representations for the cruciates. The model captured experimentally measured ligament forces (≤ 5.7 N root mean square (RMS) difference), coupled internal rotation (≤ 1.6 deg RMS difference), and coupled anterior translation (≤ 0.4 mm RMS difference) through 130 deg of passive flexion. This integrated framework of model and experiment improves our understanding of how passive structures, such as ligaments and articular geometries, interact to generate knee kinematics and ligament forces.