RESUMO
The development of new chemically resistant anodes for protonic ceramic fuel cells (PCFCs) is urgently required to avoid the costly deep hydrogen purification method. Ba0.95Ca0.05Ce0.9Y0.1O3-δ (5CBCY), which is more chemically resistant than BaCaCe0.9Y0.1O3-δ, was here tested as a component of a composite NiO-5CBCY anode material. A preparation slurry comprising 5CBCY, NiO, graphite, and an organic medium was tape cast, sintered and subjected to thermal treatment in 10 vol.% H2 in Ar at 700 °C. Differential thermal analysis, thermogravimetry, quadrupole mass spectrometry, X-ray diffraction analysis, scanning electron microscopy, the AC four-probe method and electrochemical impedance spectroscopy were used for the investigation. The electrical conductivity of the Ni-5CBCY in H2-Ar at 700 °C was 1.1 S/cm. In the same gas atmosphere but with an additional 5 vol.% CO2, it was slightly lower, at 0.8 S/cm. The Ni-5CBCY cermet exhibited repeatable electrical conductivity values during Ni-to-NiO oxidation cycles and NiO-to-Ni reduction in the 5CBCY matrix, making it sufficient for preliminary testing in PCFCs.
RESUMO
Comparative studies were performed on variations in the ABO3 perovskite structure, chemical stability in a CO2-H2 gas atmosphere, and electrical conductivity measurements in air, hydrogen, and humidity-involving gas atmospheres of monophase orthorhombic Ba1-xSrxCe0.9Y0.1O3-δ samples, where 0 < x < 0.1. The substitution of strontium with barium resulting in Ba1-xSrxCe0.9Y0.1O3-δ led to an increase in the specific free volume and global instability index when compared to BaCe0.9Y0.1O3-δ. Reductions in the tolerance factor and cell volume were found with increases in the value of x in Ba1-xSrxCe0.9Y0.1O3-δ. Based on the thermogravimetric studies performed for Ba1-xSrxCe0.9Y0.1O3-δ, where 0 < x < 0.1, it was found that modified samples of this type exhibited superior chemical resistance in a CO2 gas atmosphere when compared to BaCe0.9Y0.1O3-δ. The application of broadband impedance spectroscopy enabled the determination of the bulk and grain boundary conductivity of Ba1-xSrxCe0.9Y0.1O3-δ samples within the temperature range 25-730 °C. It was found that Ba0.98Sr0.02Ce0.9Y0.1O3-δ exhibited a slightly higher grain interior and grain boundary conductivity when compared to BaCe0.9Y0.1O3-δ. The Ba0.95Sr0.05Ce0.9Y0.1O3-δ sample also exhibited improved electrical conductivity in hydrogen gas atmospheres or atmospheres involving humidity. The greater chemical resistance of Ba1-xSrxCe0.9Y0.1O3-δ, where x = 0.02 or 0.05, in a CO2 gas atmosphere is desirable for application in proton ceramic fuel cells supplied by rich hydrogen processing gases.
RESUMO
The growing demand for clean energy catalyzes the development of new devices capable of generating electricity from renewable energy resources. One of the possible approaches focuses on the use of thermoelectric materials (TE), which may utilize waste heat, water, and solar thermal energy to generate electrical power. An improvement of the performance of such devices may be achieved through the development of composites made of an organic matrix filled with nanostructured thermoelectric materials working in a synergetic way. The first step towards such designs requires a better understanding of the fundamental interactions between available materials. In this paper, this matter is investigated and the questions regarding the change of electrical and thermal properties of nanocomposites based on low-conductive polypyrrole enriched with bismuth nanowires of well-defined geometry and morphology is answered. It is clearly demonstrated that the electrical conductivity and the Seebeck coefficient may be tuned either simultaneously or separately within particular Bi NWs content ranges, and that both parameters may be increased at the same time.
