Strategy to Efficient Photodynamic Therapy for Antibacterium: Donor-Acceptor Structure in Hydrogen-Bonded Organic Framework.

While the construction of a donor-acceptor (D-A) structure has gained great attention across various scientific disciplines, such structures are seldomly reported within the field of hydrogen-bonded organic frameworks (HOFs). Herein, a D-A based HOF is synthesized, where the adjacent D-A pairs are connected by hydrogen bonds instead of the conventionally employed covalent bonds. This structural feature imparts material with a reduced energy gap between excited state and triplet state, thereby facilitating the intersystem crossing (ISC) and boosting the generation rate of single oxygen (quantum yield = 0.98). Consequently, the resulting material shows high performance for antimicrobial photodynamic therapy (PDT). The impact of D-A moiety is evident when comparing this finding to a parallel study conducted on an isoreticular HOF without a D-A structure. The study presented here provides in-depth insights into the photophysical properties of D-A pair in a hydrogen-bonded network, opening a new avenue to the design of innovative materials for efficient PDT.

Unlock CO2 Reduction Reaction Pathways in Aprotic Li-CO2 Batteries with In Situ Isotope-Labeled Spectroscopy and Theoretical Calculations.

The CO2 reduction reaction (CO2RR) pathway significantly dictates the reversibility and overpotential of aprotic Li-CO2 batteries; however, it has remained incompletely understood due to the lack of direct in situ spectroscopic evidence. Herein, the Li-CO2RR pathways at the model Au | dimethyl sulfoxide (DMSO) interface are interrogated using a combination of in situ isotope-labeled spectroscopy techniques and theoretical calculations. This obtained direct spectroscopic evidence presents that the primary CO2RR proceeds through the CO2-to-CO pathway (i.e., 2Li+ + 2CO2 + 2e- → CO + Li2CO3) initiated at a low overpotential (ca. 2.1 V vs Li/Li+), and the CO2-to-Li2C2O4 pathway (i.e., 2Li+ + 2CO2 + 2e- → Li2C2O4) initiated at a high overpotential (ca. 1.7 V vs Li/Li+), where the potential-dependent pathways critically depend on the coverage of LiCO2 intermediates. Simultaneously, the entire Li-CO2RR process is also accompanied by parasitic reactions to form gaseous C2H4 with COOH* as the crucial intermediate, which is induced by the H+-abstraction reaction between the reactive LiCO2 intermediate and the DMSO solvent. These fundamental insights enable us to establish a molecular picture for Li-CO2RR pathways in aprotic media and will serve as a crucial guideline for reversible Li-CO2 electrochemistry.

KIr4O8 Nanowires with Rich Hydroxyl Promote Oxygen Evolution Reaction in Proton Exchange Membrane Water Electrolyzer.

The sluggish kinetics for anodic oxygen evolution reaction (OER) and insufficient catalytic performance over the corresponding Ir-based catalysts are still enormous challenges in proton exchange membrane water electrolyzer (PEMWE). Herein, it is reported that KIr4O8 nanowires anode catalyst with more exposed active sites and rich hydroxyl achieves a current density of 1.0 A cm-2 at 1.68 V and possesses excellent catalytic stability with 1230 h in PEMWE. Combining in situ Raman spectroscopy and differential electrochemical mass spectroscopy results, the modified adsorbate evolution mechanism is proposed, wherein the rich hydroxyl in the inherent structure of KIr4O8 nanowires directly participates in the catalytic process for favoring the OER. Density functional theory calculation results further suggest that the enhanced proximity between Ir (d) and O (p) band center in KIr4O8 can strengthen the covalence of Ir-O, facilitate the electron transfer between adsorbents and active sites, and decrease the energy barrier of rate-determining step from OH* to O* during the OER.

CO electrolysis to multicarbon products over grain boundary-rich Cu nanoparticles in membrane electrode assembly electrolyzers.

Producing valuable chemicals like ethylene via catalytic carbon monoxide conversion is an important nonpetroleum route. Here we demonstrate an electrochemical route for highly efficient synthesis of multicarbon (C2+) chemicals from CO. We achieve a C2+ partial current density as high as 4.35 ± 0.07 A cm-2 at a low cell voltage of 2.78 ± 0.01 V over a grain boundary-rich Cu nanoparticle catalyst in an alkaline membrane electrode assembly (MEA) electrolyzer, with a C2+ Faradaic efficiency of 87 ± 1% and a CO conversion of 85 ± 3%. Operando Raman spectroscopy and density functional theory calculations reveal that the grain boundaries of Cu nanoparticles facilitate CO adsorption and C - C coupling, thus rationalizing a qualitative trend between C2+ production and grain boundary density. A scale-up demonstration using an electrolyzer stack with five 100 cm2 MEAs achieves high C2+ and ethylene formation rates of 118.9 mmol min-1 and 1.2 L min-1, respectively, at a total current of 400 A (4 A cm-2) with a C2+ Faradaic efficiency of 64%.

Removal of diclofenac sodium from water using a polyacrylonitrile mixed-matrix membrane embedded with MOF-808.

MOF-808, owing to the synergistic effect of its large surface area and surface charge matching, showed a diclofenac sodium (DCF) removal capacity as high as 630 mg g-1, and the ability to adsorb 436 mg g-1 DCF in two hours, outperforming many common Zr-MOFs under the same conditions. Importantly, a series of free-standing mixed-matrix membranes made by combining polyacrylonitrile with MOF-808 were fabricated and exhibited high efficiency of removing DCF from water via an easily accessible filtration method.

Bridging Atom Engineering for Low-Temperature Oxygen Activation in a Robust Metal-Organic Framework.

Achieving active site engineering at the atomic level poses a significant challenge in the design and optimization of catalysts for energy-efficient catalytic processes, especially for a reaction with two reactants competitively absorbed on catalytic active sites. Herein, we show an example that tailoring the local environment of cobalt sites in a robust metal-organic framework through substituting the bridging atom from -Cl to -OH group leads to a highly active catalyst for oxygen activation in an oxidation reaction. Comprehensive characterizations reveal that this variation imparts drastic changes on the electronic structure of metal centers, the competitive reactant adsorption behavior, and the intermediate formation. As a result, exceptional low-temperature CO oxidation performance was achieved with T25(Temperature for 25 % conversion)=35 °C and T100 (Temperature for 100 % conversion)=150 °C, which stands out from existing MOF-based catalysts and even rivals many noble metal catalysts. This work provides a guidance for the rational design of catalysts for efficient oxygen activation for an oxidation reaction.

Hydrogen-bonded organic frameworks in solution enables continuous and high-crystalline membranes.

Hydrogen-Bonded organic frameworks (HOFs) are a type of emerging porous materials. At present, little research has been conducted on their solution state. This work demonstrates that HOFs fragment into small particles while maintaining their original assemblies upon dispersing in solvents, as confirmed by Cryo-electron microscopy coupled with 3D electron diffraction technology. 1D and 2D-Nuclear Magnetic Resonance (NMR) and zeta potential analyses indicate the HOF-based colloid solution and the isolated molecular solution have significant differences in intermolecular interactions and aggregation behavior. Such unique solution processibility allows for fabricating diverse continuous HOF membranes with high crystallinity and porosity through solution-casting approach on various substrates. Among them, HOF-BTB@AAO membranes show high C3H6 permeance (1.979 × 10-7 mol·s-1·m-2·Pa-1) and excellent separation performance toward C3H6 and C3H8 (SF = 14). This continuous membrane presents a green, low-cost, and efficient separation technology with potential applications in petroleum cracking and purification.

Surface Activation by Single Ru Atoms for Enhanced High-Temperature CO2 Electrolysis.

Cathodic CO2 adsorption and activation is essential for high-temperature CO2 electrolysis in solid oxide electrolysis cells (SOECs). However, the component of oxygen ionic conductor in the cathode displays limited electrocatalytic activity. Herein, stable single Ruthenium (Ru) atoms are anchored on the surface of oxygen ionic conductor (Ce0.8 Sm0.2 O2-δ , SDC) via the strong covalent metal-support interaction, which evidently modifies the electronic structure of SDC surface for favorable oxygen vacancy formation and enhanced CO2 adsorption and activation, finally evoking the electrocatalytic activity of SDC for high-temperature CO2 electrolysis. Experimentally, SOEC with the Ru1 /SDC-La0.6 Sr0.4 Co0.2 Fe0.8 O3-δ cathode exhibits a current density as high as 2.39 A cm-2 at 1.6 V and 800 °C. This work expands the application of single atom catalyst to the high-temperature electrocatalytic reaction in SOEC and provides an efficient strategy to tailor the electronic structure and electrocatalytic activity of SOEC cathode at the atomic scale.

Steering CO2 Electroreduction Selectivity U-Turn to Ethylene by Cu-Si Bonded Interface.

Copper (Cu), with the advantage of producing a deep reduction product, is a unique catalyst for the electrochemical reduction of CO2 (CO2RR). Designing a Cu-based catalyst to trigger CO2RR to a multicarbon product and understanding the accurate structure-activity relationship for elucidating reaction mechanisms still remain a challenge. Herein, we demonstrate a rational design of a core-shell structured silica-copper catalyst (p-Cu@m-SiO2) through Cu-Si direct bonding for efficient and selective CO2RR. The Cu-Si interface fulfills the inversion in CO2RR product selectivity. The product ratio of C2H4/CH4 changes from 0.6 to 14.4 after silica modification, and the current density reaches a high of up to 450 mA cm-2. The kinetic isotopic effect, in situ attenuated total reflection Fourier-transform infrared spectra, and density functional theory were applied to elucidate the reaction mechanism. The SiO2 shell stabilizes the *H intermediate by forming Si-O-H and inhibits the hydrogen evolution reaction effectively. Moreover, the direct-bonded Cu-Si interface makes bare Cu sites with larger charge density. Such bare Cu sites and Si-O-H sites stabilized the *CHO and activated the *CO, promoting the coupling of *CHO and *CO intermediates to form C2H4. This work provides a promising strategy for designing Cu-based catalysts with high C2H4 catalytic activity.

Insights into the mechanism in electrochemical CO2 reduction over single-atom copper alloy catalysts: A DFT study.

Copper single-atom alloy catalysts (M@Cu SAAs) have shown great promise for electrochemical CO2 reduction reaction (CO2RR). However, a clear understanding of the CO2RR process on M@Cu SAAs is still lacking. This study uses density functional theoretical (DFT) calculations to obtain a comprehensive mechanism and the origin of activity of M@Cu SAAs. The importance of the adsorption mode of M@Cu is revealed: key intermediates either adsorbed in the adjacent hollow site around Cu atoms (AD mode) or adsorbed directly on the top site of M (SE mode). AD mode generally exhibits finely tuned binding strengths of key intermediates, which significantly enhances the activity of the catalysts. Increasing the coverage of ∗CO on the M@Cu with SE mode leads to relocation of the active site, resulting in improved activity of C2 products. The insights gained in this work have significant implications for rational design strategy toward efficient CO2RR electrocatalysts.

Directing the Selectivity of CO Electrolysis to Acetate by Constructing Metal-Organic Interfaces.

Electrochemically converting CO2 to valuable chemicals holds great promise for closing the anthropogenic carbon cycle. Owing to complex reaction pathways and shared rate-determining steps, directing the selectivity of CO2 /CO electrolysis to a specific multicarbon product is very challenging. We report here a strategy for highly selective production of acetate from CO electrolysis by constructing metal-organic interfaces. We demonstrate that the Cu-organic interfaces constructed by in situ reconstruction of Cu complexes show very impressive acetate selectivity, with a high Faradaic efficiency of 84.2 % and a carbon selectivity of 92.1 % for acetate production, in an alkaline membrane electrode assembly electrolyzer. The maximum acetate partial current density and acetate yield reach as high as 605 mA cm-2 and 63.4 %, respectively. Thorough structural characterizations, control experiments, operando Raman spectroscopy measurements, and density functional theory calculation results indicate that the Cu-organic interface creates a favorable reaction microenvironment that enhances *CO adsorption, lowers the energy barrier for C-C coupling, and facilitates the formation of CH3 COOH over other multicarbon products, thus rationalizing the selective acetate production.

In situ electrochemical reconstruction of Sr2Fe1.45Ir0.05Mo0.5O6-δ perovskite cathode for CO2 electrolysis in solid oxide electrolysis cells.

Solid oxide electrolysis cells provide a practical solution for the direct conversion of CO2 to other chemicals (i.e. CO), however, an in-depth mechanistic understanding of the dynamic reconstruction of active sites for perovskite cathodes during CO2 electrolysis remains a great challenge. Herein, we identify that iridium-doped Sr2Fe1.45Ir0.05Mo0.5O6-δ (SFIrM) perovskite displays a dynamic electrochemical reconstruction feature during CO2 electrolysis with abundant exsolution of highly dispersed IrFe alloy nanoparticles on the SFIrM surface. The in situ reconstructed IrFe@SFIrM interfaces deliver a current density of 1.46 A cm-2 while maintaining over 99% CO Faradaic efficiency, representing a 25.8% improvement compared with the Sr2Fe1.5Mo0.5O6-δ counterpart. In situ electrochemical spectroscopy measurements and density functional theory calculations suggest that the improved CO2 electrolysis activity originates from the facilitated formation of carbonate intermediates at the IrFe@SFIrM interfaces. Our work may open the possibility of using an in situ electrochemical poling method for CO2 electrolysis in practice.

Solution-Processed Hydrogen-Bonded Organic Framework Nanofilms for High-Performance Resistive Memory Devices.

The integration of hydrogen-bonded organic frameworks (HOFs) into electronic devices holds great promise due to their high crystallinity, intrinsic porosity, and easy regeneration. However, despite their potential, the utilization of HOFs in electronic devices remains largely unexplored, primarily due to the challenges associated with fabricating high-quality films. Herein, a controlled synthesis of HOF nanofilms with smooth surface, good crystallinity, and high orientation is achieved using a solution-processed approach. The memristors exhibit outstanding bipolar switching performance with a low set voltage of 0.86 V, excellent retention of 1.64 × 104 s, and operational endurance of 60 cycles. Additionally, these robust memristors display remarkable thermal stability, maintaining their performance even at elevated temperatures of up to 200 °C. More strikingly, scratched HOF films can be readily regenerated through a simple solvent rinsing process, enabling their reuse for the fabrication of new memristors, which is difficult to achieve with traditional resistive switching materials. Additionally, a switching mechanism based on the reversible formation and annihilation of conductive filaments is revealed. This work provides novel and invaluable insights that have a significant impact on advancing the widespread adoption of HOFs as active layers in electronic devices.

Shexiang Baoxin Pill treats acute myocardial infarction by promoting angiogenesis via GDF15-TRPV4 signaling.

Angiogenesis has been considered a pivotal strategy for treating ischemic heart disease. One possible approach, the Shexiang Baoxin Pill (MUSKARDIA), has been noted to promote angiogenesis, but its underlying mechanism is still largely unknown. We aimed to determine the effects of MUSKARDIA on acute myocardial infarction (AMI), as well as the underlying mechanistic bases. AMI was induced in rats, using left anterior descending coronary arterial occlusion, and either 6 (low) or 12 (high-dose) mg/kg/day of MUSKARDIA was administered for 56 days. We found that MUSKARDIA improved cardiac function and counteracted against adverse remodeling among AMI rats, which most likely is due to it promoting angiogenesis. Transcriptome analysis by RNA-sequencing found that MUSKARDIA up-regulated cardiac pro-angiogenic genes, particularly growth differentiation factor 15 (GDF15), which was confirmed by RT-qPCR. This up-regulation was also correlated with elevated serum GDF15 levels. In vitro analyses with human umbilical vein endothelial cells found that increased GDF15, stimulated by MUSKARDIA, resulted in enhanced cell migration, proliferation, and tubular formation, all of which were reversed after GDF15 knockdown using a lentiviral vector. Gene Ontology, as well as Kyoto Genes and Genomes enrichment analyses identified calcium signaling pathway as a major contributor to these outcomes, which was verified by Western blot and Cal-590 AM loading showing that transient receptor potential cation channel subfamily V member 4 protein (TRPV4) and intracellular Ca2+ levels increased in accordance with MUSKARDIA-induced GDF15 up-regulation, and decreased with GDF15 knock-down. Therefore, MUSKARDIA may exert its cardioprotective effects via stimulating the GDF15/TRPV4/calcium signaling/angiogenesis axis.

Tailoring Ion Ordering in Perovskite Oxide for High-Temperature Oxygen Evolution Reaction.

Perovskites exhibit excellent high-temperature oxygen evolution reaction (OER) activities as the anodes of solid oxide electrolysis cells (SOECs). However, the relationship between ion ordering and OER performances is rarely investigated. Herein, a series of PrBaCo2-x Fex O5+δ perovskites with tailored ion orderings are constructed. Physicochemical characterizations and density functional theory calculations confirm that the oxygen bulk migration and surface transport capacities as well as the OER activities are promoted by the A-site cation ordering, but weakened by the oxygen vacancy ordering. Hence, SOEC with the A-site-ordered and oxygen-vacancy-disordered PrBaCo2 O5+δ anode exhibits the highest performance of 3.40 A cm-2 at 800 °C and 2.0 V. This work sheds light on the critical role of ion orderings in the high-temperature OER performance and paves a new way for screening novel anode materials of SOECs.

A porous metal-organic cage liquid for sustainable CO2 conversion reactions.

Porous liquids are fluids with the permanent porosity, which can overcome the poor gas solubility limitations of conventional porous solid materials for three phase gas-liquid-solid reactions. However, preparation of porous liquids still requires the complicated and tedious use of porous hosts and bulky liquids. Herein, we develop a facile method to produce a porous metal-organic cage (MOC) liquid (Im-PL-Cage) by self-assembly of long polyethylene glycol (PEG)-imidazolium chain functional linkers, calixarene molecules and Zn ions. The Im-PL-Cage in neat liquid has permanent porosity and fluidity, endowing it with a high capacity of CO2 adsorption. Thus, the CO2 stored in an Im-PL-Cage can be efficiently converted to the value-added formylation product in the atmosphere, which far exceeds the porous MOC solid and nonporous PEG-imidazolium counterparts. This work offers a new method to prepare neat porous liquids for catalytic transformation of adsorbed gas molecules.

Machine learning of spectra-property relationship for imperfect and small chemistry data.

Machine learning (ML) is causing profound changes to chemical research through its powerful statistical and mathematical methodological capabilities. However, the nature of chemistry experiments often sets very high hurdles to collect high-quality data that are deficiency free, contradicting the need of ML to learn from big data. Even worse, the black-box nature of most ML methods requires more abundant data to ensure good transferability. Herein, we combine physics-based spectral descriptors with a symbolic regression method to establish interpretable spectra-property relationship. Using the machine-learned mathematical formulas, we have predicted the adsorption energy and charge transfer of the CO-adsorbed Cu-based MOF systems from their infrared and Raman spectra. The explicit prediction models are robust, allowing them to be transferrable to small and low-quality dataset containing partial errors. Surprisingly, they can be used to identify and clean error data, which are common data scenarios in real experiments. Such robust learning protocol will significantly enhance the applicability of machine-learned spectroscopy for chemical science.

Enhancing Electrochemical Nitrate Reduction to Ammonia over Cu Nanosheets via Facet Tandem Catalysis.

Electrochemical conversion of nitrate (NO3 - ) into ammonia (NH3 ) represents a potential way for achieving carbon-free NH3 production while balancing the nitrogen cycle. Herein we report a high-performance Cu nanosheets catalyst which delivers a NH3 partial current density of 665 mA cm-2 and NH3 yield rate of 1.41 mmol h-1 cm-2 in a flow cell at -0.59 V vs. reversible hydrogen electrode. The catalyst showed a high stability for 700 h with NH3 Faradaic efficiency of ≈88 % at 365 mA cm-2 . In situ spectroscopy results verify that Cu nanosheets are in situ derived from the as-prepared CuO nanosheets under electrochemical NO3 - reduction reaction conditions. Electrochemical measurements and density functional theory calculations indicate that the high performance is attributed to the tandem interaction of Cu(100) and Cu(111) facets. The NO2 - generated on the Cu(100) facets is subsequently hydrogenated on the Cu(111) facets, thus the tandem catalysis promotes the crucial hydrogenation of *NO to *NOH for NH3 production.

The Role of Interfacial Water in CO2 Electrolysis over Ni-N-C Catalyst in a Membrane Electrode Assembly Electrolyzer.

CO2 electrolysis is a promising route for achieving net-zero emission through decarbonization. To realize CO2 electrolysis toward practical application, beyond catalyst structures, it is also critical to rationally manipulate catalyst microenvironments such as the water at the electrode/electrolyte interface. Here, the role of interfacial water in CO2 electrolysis over Ni-N-C catalyst modified with different polymers is investigated. Benefiting from a hydrophilic electrode/electrolyte interface, the Ni-N-C catalyst modified with quaternary ammonia poly(N-methyl-piperidine-co-p-terphenyl) shows a Faradaic efficiency of 95% and a partial current density of 665 mA cm-2 for CO production in an alkaline membrane electrode assembly electrolyzer. A scale-up demonstration using a 100 cm2 electrolyzer achieves a CO production rate of 514 mL min-1 at a current of 80 A. In-situ microscopy and spectroscopy measurements indicate that the hydrophilic interface significantly promotes the formation of the *COOH intermediate, rationalizing the high CO2 electrolysis performance.

Structurally-New Hexadecanuclear Ni-Containing Silicotungstate with Catalytic Hydrogen Generation Activity.

A structurally-new, carbon-free hexadecanuclear Ni-containing silicotungstate, [Ni16(H2O)15(OH)9(PO4)4(SiW9O34)3]19-, has been facilely synthesized using a one-pot, solution-based synthetic method systematically characterized by single-crystal X-ray diffraction and several other techniques. The resulting complex works as a noble-metal-free catalyst for visible-light-driven catalytic generation of hydrogen, by coupling with a [Ir(coumarin)2(dtbbpy)][PF6] photosensitizer and a triethanolamine (TEOA) sacrificial electron donor. Under minimally optimized conditions, a turnover number (TON) of 842 was achieved for TBA-Ni16P4(SiW9)3-catalyzed hydrogen evolution system. The structural stability of TBA-Ni16P4(SiW9)3 catalyst under photocatalytic conditions was evaluated by the mercury-poisoning test, FT-IR, and DLS measurements. The photocatalytic mechanism was elucidated by both time-solved luminescence decay and static emission quenching measurements.