Viability of Total Ammoniacal Nitrogen Recovery Using a Polymeric Thin-Film Composite Forward Osmosis Membrane: Determination of Ammonia Permeability Coefficient.

Total ammoniacal nitrogen (TAN) occurs in various wastewaters and its recovery is vital for environmental reasons. Forward osmosis (FO), an energy-efficient technology, extracts water from a feed solution (FS) and into a draw solution (DS). Asymmetric FO membranes consist of an active layer and a support layer, leading to internal concentration polarization (ICP). In this study, we assessed TAN recovery using a polymeric thin-film composite FO membrane by determining the permeability coefficients of NH4+ and NH3. Calculations employed the solution-diffusion model, Nernst-Planck equation, and film theory, applying the acid-base equilibrium for bulk concentration corrections. Initially, model parameters were estimated using sodium salt solutions as the DS and deionized water as the FS. The NH4+ permeability coefficient was 0.45 µm/s for NH4Cl and 0.013 µm/s for (NH4)2SO4 at pH < 7. Meanwhile, the NH3 permeability coefficient was 6.18 µm/s at pH > 9 for both ammonium salts. Polymeric FO membranes can simultaneously recover ammonia and water, achieving 15% and 35% recovery at pH 11.5, respectively.

Experimental and Modeling Study of the Nanofiltration of Alcohol-Based Molecules and Amino Acids by Commercial Membranes.

The nanofiltration performance of three commercial membranes was analyzed by the Steric Pore Model (SPM) and the extended Nernst-Planck diffusion equation inside membrane pores. The model was completed with the equation to predict the concentration polarization, and the mass transfer coefficient was determined by considering the presence of a feed spacer. The model parameters that characterized the performance of the membrane were the hydrodynamic coefficient, which accounts for the possible variations in solute size and membrane pore radius, the effective membrane thickness, and the water permeability coefficient. All experiments were conducted at fixed feed pH of 6. The rejections of uncharged solutes (glucose for membranes with a high molecular weight cut-off (MWCO) and glycerol and ethylene glycol for membranes with a low MWCO) allowed the model parameters to be determined. We found that glycerol and ethylene glycol overestimate the membrane pore radius due to their ability to interact with the membrane matrix. Therefore, the rejection of glycine as a small amino acid was explored to characterize the membranes with low MWCO since these molecules do not interact with the membrane matrix and have an almost zero charge at pH values between 4.5 and 6.5. Based on the experimental rejections, it was stated that glucose and glycine could be separated by these membranes operating in continuous diafiltration mode.

Comparative Study on the Stiffness of Poly(lactic acid) Reinforced with Untreated and Bleached Hemp Fibers.

Composite materials containing natural reinforcement fibers, generally called biocomposites, have attracted the interest of both researchers and manufacturers, but the most environmentally advantageous combinations include a bio-based matrix, as well. With this in mind, a poly(lactic acid) (PLA) matrix was reinforced with natural fibers from hemp, both untreated strands (UHSs) and soda-bleached fibers (SBHFs). The preparation of the subsequent fully bio-sourced, discontinuously reinforced composites involved kinetic mixing, intensive single-screw extrusion, milling, and injection molding. Up to a fiber content of 30 wt%, the tensile modulus increased linearly with the volume fraction of the dispersed phase. Differences between SBHFs (up to 7.6 Gpa) and UHSs (up to 6.9 Gpa) were hardly significant (p = 0.1), but SBHF-reinforced composites displayed higher strain at failure. In any case, for the same fiber load (30 wt%), the Young's modulus of PLA/hemp biocomposites was greater than that of glass fiber (GF)-reinforced polypropylene (5.7 GPa), albeit lower than that of PLA/GF (9.8 GPa). Considering all the measurements, the contribution of each phase was analyzed by applying the Hirsch model and the Tsai-Pagano model. As a concluding remark, although the intrinsic tensile modulus of SBHFs was lower than that of GF, the efficiency of those natural fibers as reinforcement (according to the rule of mixtures) was found to be higher.

Methodologies to Evaluate the Micromechanics Flexural Strength Properties of Natural-Fiber-Reinforced Composites: The Case of Abaca-Fiber-Reinforced Bio Polyethylene Composites.

There is growing emphasis on developing green composites as a substitute for oil-based materials. In the pursuit of studying and enhancing the mechanical properties of these composites, tensile tests are predominantly employed, often overlooking the flexural properties. This study focuses on researching the flexural properties of abaca-fiber-reinforced bio-based high-density polyethylene (BioPE) composites. Specifically, composites containing 30 wt% of abaca fiber (AF) were treated with a coupling agent based on polyethylene functionalized with maleic acid (MAPE). The test results indicate that incorporating 8 wt% of the coupling agent significantly improved the flexural strength of the composites. Thereafter, composites with AF content ranging from 20 to 50 wt% were produced and subjected to flexural testing. It was observed that flexural strength was positively correlated with AF content. A micromechanics analysis was conducted to evaluate the contributions of the phases. This analysis involved assessing the mechanical properties of both the reinforcement and matrix to facilitate the modeling of flexural strength. The findings of this study demonstrate the feasibility of replacing oil-based matrices, such as high-density polyethylene (HDPE), with fully bio-based composites that exhibit comparable flexural properties to their oil-based counterparts.

Influence of pH and NaCl on the rejection of glycine and triglycine in binary solutions for desalination with diananofiltration.

Nanofiltration can be used as the last step in the purification of the biomolecules that are present in many industrial by-products, such as biological protein hydrolysates. The present study explored the variation in glycine and triglycine rejections in binary solutions with NaCl at different feed pHs with two nanofiltration membranes: MPF-36 and Desal 5DK with molecular weight cut-offs of 1000 and 200 g mol-1, respectively. First, water permeability coefficient showed a n-shaped curve with feed pH, which was more evident for the MPF-36 membrane. Second, membrane performance with single solutions was studied and the experimental data were fitted with the Donnan steric pore model with dielectric exclusion (DSPM-DE) to explain the variations of solute rejection with feed pHs. Glucose rejection was assessed to estimate the membrane pore radius of the MPF-36 membrane, and a pH dependence was observed. For a tight membrane (Desal 5DK), glucose rejection was close to unity and the membrane pore radius was estimated from the glycine rejection in the feed pH range from 3.7 to 8.4. Glycine and triglycine rejections showed a pH-dependence with a u-shaped curve, even for the zwitterion species. In binary solutions, glycine and triglycine rejections decreased with NaCl concentration, especially in the MPF-36 membrane. Triglycine rejection was always higher than NaCl rejection and it was estimated that triglycine can be desalted using a continuous diananofiltration the Desal 5DK membrane.

Chlorine resistance property improvement of polyamide reverse osmosis membranes through cross-linking degree increment.

Highly permeable polyamide reverse osmosis (RO) membranes are desirable for reducing the energy burden and ensuring future water resources in arid and semiarid regions. One notable drawback of thin film composite (TFC) polyamide RO/NF membranes is the polyamide's sensitivity to degradation by free chlorine, the most used biocide in water purification trains. This investigation demonstrated a significant increase in the crosslinking-degree parameter by the m-phenylenediamine (MPD) chemical structure extending in the thin film nanocomposite (TFN) membrane without adding extra MPD monomers to enhance the chlorine resistance and performance. Membrane modification was carried out according to monomer ratio changes and Nanoparticle embedding into the PA layer approaches. A new class of TFN-RO membranes incorporating novel aromatic amine functionalized (AAF)-MWCNTs embedded into the polyamide (PA) layer was introduced. A purposeful strategy was carried out to use cyanuric chloride (2,4,6-trichloro-1,3,5-triazine) as an intermediate functional group in the AAF-MWCNTs. Thus, amidic nitrogen, connected to benzene rings and carbonyl groups, assembles a structure similar to the standard PA, consisting of MPD and trimesoyl chloride. The resulting AAF-MWCNTs were mixed in the aqueous phase during the interfacial polymerization to increase the susceptible positions to chlorine attack and improve the crosslinking degree in the PA network. The characterization and performance results of the membrane demonstrated an increase in ion selectivity and water flux, impressive stability of salt rejection after chlorine exposure, and improved antifouling performance. This purposeful modification resulted in overthrowing two tradeoffs; i) high crosslink density-water flux and ii) salt rejection-permeability. The modified membrane demonstrated ameliorative chlorine resistance relative to the pristine one, with twice the increase in crosslinking degree, more than four times the enhancement of the oxidation resistance, negligible reduction in the salt rejection (0.83 %), and only 5 L/m2.h flux loss following a rigorous static chlorine exposure of 500 ppm.h under acidic conditions. The excellent performance of new chlorine resistant TNF RO membranes fabricated via AAF-MWCNTs together with the facile membrane manufacturing process offered the possibility of postulating them in the desalination field, which could eventually help the current freshwater supply challenge.

Experimental Behavior of Thin-Tile Masonry under Uniaxial Compression. Multi-Leaf Case Study.

In this study, experimental analysis on the compressive strength of multi-leaf thin-tile masonry is presented. A compressive strength test was carried out on thin-tile, mortar and 48 specimens with two- and three-leaf thin-tile masonry. The results obtained were compared with literature on brick masonry loaded parallel to a bed joint. Based on the results of this study, the failure mode presented the first crack in the vertical interface; this crack grew until the leaf was detached. From this point until collapse, lateral buckling of the leaves was generally observed. Therefore, the detachment compressive strength value was considered relevant. Up to this point, both masonries exhibit similar stress-strain behavior. The experimental values of the detachment compressive strength were compared with the values calculated from the equation generally used in the literature to evaluate the compressive strength of brick masonry. From the results obtained, the following conclusion can be drawn: This equation is only suitable for tree-leaf thin-tile masonry but with more relevant influence on the compressive strength of the mortar. This study concluded that only three-leaf specimens behave similarly to brick masonry loaded parallel to a bed joint. Finally, whether the failure mode was due to shear or tensile stresses in the vertical thin-tile-mortar interface cannot be identified.

On the Path to a New Generation of Cement-Based Composites through the Use of Lignocellulosic Micro/Nanofibers.

Due to its high biocompatibility, bio-degradability, and low cost, cellulose finds application in disparate areas of research. Here we focus our attention on the potential applications of cellulose nanofiber in cement-based materials for the building sector. We first describe the chemical/morphological composition of cellulose fibers, their process and treatment, the characterization of cement-based composites, and their flexural strength. In recent research in this field, cellulose has been considered in the form of nano-sized particles, i.e., cellulose nanofibers (CNF) or cellulose nanocrystals (CNC). CNF and CNC are used for several reasons, including their mechanical and thermal properties, their extended surface area and low toxicity. This study presents some potential applications of lignocellulosic micro/nanofibers (LCMNF) in cement-based composites in order to improve flexural strength. Samples were made with 0.5-1.0-1.5-2.0 wt% of LCMNF obtained from pine sawdust, CEM I (Portland) and a 1:3 cement-water ratio. The composites were then tested for flexural strength at 7, 14, and 28 days and the evolution of flexural strength was assessed after water immersion during 72 h. Scanning electron microscopy was employed to visualize the bond between LCMNF and the cement matrix. Results showed that LCMNF improved the flexural strength of the composite in all the dosages used.

Effect of Hydrodynamic Forces on meso-(4-Sulfonatophenyl)-Substituted Porphyrin J-Aggregate Nanoparticles: Elasticity, Plasticity and Breaking.

The J aggregates of 4-sulfonatophenyl meso-substituted porphyrins are non-covalent polymers obtained by self-assembly that form nanoparticles of different morphologies. In the case of high aspect-ratio nanoparticles (bilayered ribbons and monolayered nanotubes), shear hydrodynamic forces may modify their shape and size, as observed by peak force microscopy, transmission electron microscopy of frozen solutions, small-angle X-ray scattering measurements in a disk-plate rotational cell, and cone-plate rotational viscometry. These nanoparticles either show elastic or plastic behaviour: there is plasticity in the ribbons obtained upon nanotube collapse on solid/air interfaces and in viscous concentrated nanotube solutions, whereas elasticity occurs in the case of dilute nanotube solutions. Sonication and strong shear hydrodynamic forces lead to the breaking of the monolayered nanotubes into small particles, which then associate into large colloidal particles.

Effects of inorganic nitrogen (NH4Cl) and biodegradable organic carbon (CH3COONa) additions on a pilot-scale seawater biofilter.

Biofilters degrade a small fraction of the natural organic matter (NOM) contained in seawater which is the leading cause of biofouling in downstream processes. This work studies the effects of chemical additions on NOM biodegradation by biofilters. In this work, biofiltration of seawater with an empty bed contact time (EBCT) of 6 min and a hydraulic loading rate of 10 mh(-1) reduces the biological oxygen demand (BOD7) by 8%, the dissolved organic carbon (DOC) by 6% and the UV absorbance at 254 nm (A254) by 7%. Different amounts of ammonium chloride are added to the seawater (up to twice the total dissolved nitrogen in untreated seawater) to study its possible effect on the removal of NOM by a pilot-scale biofilter. Seawater is amended with different amounts of easily biodegradable dissolved organic carbon (BDOC) supplied as sodium acetate (up to twice the DOC) for the same purpose. The results of this work reveal that the ammonium chloride additions do not significantly affect NOM removal and the sodium acetate is completely consumed by the biofiltration process. For both types of chemical additions, the BOD7, DOC and A254 in the outlet stream of the biofilter are similar to the values for the untreated control. These results indicate that this biofilter easily removes the BDOC from the seawater when the EBCT is not above 6 min. Furthermore, nitrogen does not limit the NOM biodegradation in seawater under these experimental conditions.

Chirality generated by flows in pseudocyanine dye J-aggregates: revisiting 40 years old reports.

Spontaneous symmetry breaking in J-aggregates of cyanine dyes has a long history in chemical literature. In 1976, Honda and Hada claimed that they had achieved chiral induction (CD) by stirring J-aggregates of pseudocyanine. However, this report is controversial, as the combinations of linear dichroism and birefringence can lead to artifactual circular dichroic signals that are unrelated to molecular chirality. A Mueller matrix spectroscopy study, with an approach for the application of a gradient of the shear rate (solution layer between a rotating and a fixed disk) that differs from the simple vortex stirring used in the original report, shows that true CD can be induced in the sample. The phenomenon is discussed, taking into account the flow dynamics that allows the alignment of the aggregate particles and the gradient of shear rates that determines their folding/torsion, which leads to a chiral excitonic transition.

Improvement of the analysis of the biochemical oxygen demand (BOD) of Mediterranean seawater by seeding control.

Biochemical oxygen demand (BOD) is a useful parameter for assessing the biodegradability of dissolved organic matter in water. At the same time, this parameter is used to evaluate the efficiency with which certain processes remove biodegradable natural organic matter (NOM). However, the values of BOD in seawater are very low (around 2 mgO(2)L(-1)) and the methods used for its analysis are poorly developed. The increasing attention given to seawater desalination in the Mediterranean environment, and related phenomena such as reverse osmosis membrane biofouling, have stimulated interest in seawater BOD close to the Spanish coast. In this study the BOD analysis protocol was refined by introduction of a new step in which a critical quantity of autochthonous microorganisms, measured as adenosine triphosphate, is added. For the samples analyzed, this improvement allowed us to obtain reliable and replicable BOD measurements, standardized with solutions of glucose-glutamic acid and acetate. After 7 days of analysis duration, more than 80% of ultimate BOD is achieved, which in the case of easily biodegradable compounds represents nearly a 60% of the theoretical oxygen demand. BOD(7) obtained from the Mediterranean Sea found to be 2.0±0.3 mgO(2)L(-1) but this value decreased with seawater storage time due to the rapid consumption of labile compounds. No significant differences were found between two samples points located on the Spanish coast, since their organic matter content was similar. Finally, the determination of seawater BOD without the use of inoculum may lead to an underestimation of BOD.

Emergence of supramolecular chirality by flows.

Hydrodynamic forces in stirred solutions induce chirality in some supramolecular species of J-aggregates, as detected at the level of the electronic transition. However, the mechanism that explains the phenomenon remains to be elucidated, although the basic effect of hydrodynamic gradients of the shear rate is most probably the folding or bending of the nanoparticles in solution. Herein, we demonstrate a correlation between chiral flows in different regions of circular and square stirred cuvettes and the emergence of true circular dichroism (CD). The results show that chaotic flows lead to a racemic mixture of chiral shaped supramolecular species, and vortical flows to scalemic mixtures. In a magnetically stirred flask the descending and ascending flows are of different chiral sign and the CD reading depends on the weighting of these two flows of inverse chiral sign. The effect of the gradient of shear rates of the flows leading to chiral shape objects depends on the shape of the cuvette, which suggests that the flask shape and the controlled addition of reagents in defined regions of the stirred solutions may exert a control in self-assembly processes.

Reversible mechanical induction of optical activity in solutions of soft-matter nanophases.

Nanophases of J-aggregates of several achiral amphiphilic porphyrins, which have thin long acicular shapes (nanoribbons), show the immediate and reversible formation of a stationary mechano-chiral state in the solution by vortex stirring, as detected by their circular dichroic signals measured by 2-modulator generalized ellipsometry. The results suggest that when a macroscopic chiral force creates supramolecular chirality, it also creates an enantiomeric excess of screw distortions, which may be detected by their excitonic absorption. An explanation on the effect of the shear flow gradients is proposed on the basis of the orientation of the rotating particles in the vortex and the size, shape, and mechanical properties of the nanoparticles.

A thermodynamic analysis of gas adsorption on microporous materials: evaluation of energy heterogeneity.

This paper presents a thermodynamic isotherm derived from solution thermodynamics principles to describe gas adsorption on microporous materials. This isotherm relies on a potential relationship between the integral free energy of adsorption relative to saturation, Psi/RT, expressed by the Kiselev equation, and the variable Z = 1/-Ln(Pi), being Pi the relative pressure. A mathematical analysis reveals that the adsorption energy heterogeneity in the micropores is collected in a characteristic parameter of the isotherm, m, that can be related to the alpha parameter of the Dubinin-Astakhov isotherm in a simple way (m = alpha + 1). The isotherm also predicts a plateau in Psi/RT at extremely low pressures (Pi < 10(-7)). Neimark's thermodynamic equation accounting for gas adsorption on mesoporous solids is found to be a particular case of the isotherm presented in this study. The Langmuir isotherm only shows consistency with the thermodynamic isotherm for a reduced combination of values of the relevant parameters, not usually found in common adsorbents. The suitability of the thermodynamic isotherm is experimentally assessed by testing a collection of microporous materials, including activated carbons, carbon nanotubes, and zeolites.

Influence of sodium polyacrylate on the rheology of aqueous Laponite dispersions.

Aqueous Laponite dispersions containing a sodium polyacrylate were analyzed, at fixed ionic strength and pH, by rheometric and electroacoustic (for zeta-potential determinations) techniques at 7 days after their preparation. The rheological behavior of these dispersions was determined by oscillatory and flow experiments. Addition of sodium polyacrylate modifies the interactions between Laponite particles and therefore the physical state of the dispersion. The phase diagram of Laponite dispersion as a function of sodium polyacrylate concentration shows different sol-gel transitions for a specific Laponite concentration as a function of the polyacrylate concentration. Under equilibrium flow conditions the Laponite dispersions fit the pseudoplastic Oswald-de Waele power law model. At the same time, these dispersions show thixotropy, which was analyzed using a second-order kinetic equation. The kinetic processes were characterized by breakdown and build-up parameters, which were found to depend on shear rate. This kinetic equation was modified by a power law exponent of viscosity with shear rate that takes into account the viscosity variations when the shear rates are suddenly changed, in order to fit the hysteresis loops.

Comparison of polysulfone and ceramic membranes for the separation of phenol in micellar-enhanced ultrafiltration.

Micellar-enhanced ultrafiltration (MEUF) of phenol and a cationic surfactant, cetylpyridinium chloride (CPC), is studied using two polysulfone membranes of 5- and 50-kDa molecular weight cutoff (MWCO) and two ceramic membranes of 15- and 50-kDa MWCO. Filtrations are run under laminar cross-flow and steady-state conditions. The effect of operation variables (pressure and retentate flux) and membrane properties (nature and MWCO) on permeate flux, surfactant, and phenol rejections is analyzed. The permeate flux depends, among other variables, on the fouling favored by membrane-micelle interactions, which are strongest in the 50-kDa MWCO ceramic membrane. On the other hand, surfactant rejection is mainly determined by the pore size and influenced by the pressure for both 50-kDa MWCO membranes. An equilibrium distribution constant, K(s), of phenol between surfactant micelles and water is calculated. Its value is not significantly affected by operation conditions and membrane type. K(s) is also approximately 20% lower than the value determined in a previous work with batch dead-end ultrafiltration.

Nitrogen Sorption Studies of Silica Particles Obtained in Emulsion and Microemulsion Media.

The internal surface structures of silica aerogel particles synthesized using different catalysts in emulsion and microemulsion media have been investigated by means of N(2) adsorption and desorption isotherms. Surface fractal dimensions have been computed using different methods: Frankel-Halsey-Hill plots of the adsorption isotherms, the thermodynamic fractal isotherm equation, and a modification of the thermodynamic fractal isotherm equation. Silica aerogels synthesized in emulsion media with an acidic catalyst have a high specific surface area without micropores and show two separate ranges of scales where the surface fractal dimensions are different and constant. Silica aerogels synthesized in emulsion media with a basic catalyst have a moderate specific surface area with a high percentage of micropores and show constant surface fractal dimensions over a larger range. Silica aerogels synthesized in microemulsion media with a basic catalyst have a low specific surface area with a moderate percentage of micropores and show a moderate range of scales over which the surface fractal dimension is constant. Analyses by both the thermodynamic and modified thermodynamic methods give similar ranges of the surface fractal dimensions of the silica particles. Copyright 2000 Academic Press.