Relationship between photo-physical and electrochemical properties of D-π-A compounds regarding solar cell applications. 1. Substituent type effect in photovoltaic performance.

Studying the electrochemical characteristics is an important step for determining interactions between molecules and the chemical environment. Moreover, the electrochemical evaluation of dyes is highly needed to establish the behavior of electro-active chemical species inside dye-sensitized solar cells (DSSCs). Four compounds, M8-1, M8-2, M8-O1, and M8-O2 (with a common organic structure (E)-2-cyano-3-(5-((E)-2-(9,9-diethyl-7-(phenylamino)-9H-fluoren-2-yl)vinyl)thiophen-2-yl)acrylic acid), are studied in two solvents, tetrahydrofuran (THF) and dimethylsulfoxide (DMSO). Among the studied compounds, M8-1 has highlighted characteristics compared with the others: its ground and excited states oxidation potential are the highest (1.14 and -1.22 V, respectively). Also, it shows the lowest energy gap between the excited state oxidation potential and the TiO2 conduction band. Relating to the substituent effect, the shorter the length, the higher the energetic difference in the electronic transition (M8-1 and 2). Comparing characteristics through quantum chemistry, the values obtained in DMSO are the most predictable. The injection energies signal that M8-1 is the best injector. The performances in solar cells are measured in three TiO2 materials: Degussa (D-TiO2), active opaque (A-TiO2), and transparent (T-TiO2). The IPCE results show the A > T > D average tendency, and the family of substituted alkyl has higher values than the alcoxyl one. Furthermore, in the first family the methyl substituent has a higher value than the ethyl one. M8-1 has the highest IPCE value, on average. In terms of efficiency, the alkyl substituted family again has higher values than the alcoxyl family. On average, the methyl substituent has a higher value than the ethyl one in both families. M8-1 has the highest efficiency value.

Early adhesion of human mesenchymal stem cells on TiO(2) surfaces studied by single-cell force spectroscopy measurements.

Understanding the interactions involved in the adhesion of living cells on surfaces is essential in the field of tissue engineering and biomaterials. In this study, we investigate the early adhesion of living human mesenchymal stem cells (hMSCs) on flat titanium dioxide (TiO(2) ) and on nanoporous crystallized TiO(2) surfaces with the use of atomic force microscopy-based single-cell force spectroscopy measurements. The choice of the substrate surfaces was motivated by the fact that implants widely used in orthopaedic and dental surgery are made in Ti and its alloys. Nanoporous TiO(2) surfaces were produced by anodization of Ti surfaces. In a typical force spectroscopy experiment, one living hMSC, immobilized onto a fibronectine-functionalized tipless lever is brought in contact with the surface of interest for 30 s before being detached while recording force-distance curves. Adhesion of hMSCs on nanoporous TiO(2) substrates having inner pore diameter of 45 nm was lower by approximately 25% than on TiO(2) flat surfaces. Force-distance curves exhibited also force steps that can be related to the pulling of membrane tethers from the cell membrane. The mean force step was equal to 35 pN for a given speed independently of the substrate surface probed. The number of tethers observed was substrate dependent. Our results suggest that the strength of the initial adhesion between hMSCs and flat or nanoporous TiO(2) surfaces is driven by the adsorption of proteins deposited from serum in the culture media.

Surface characterization and efficiency of a matrix-free and flat carboxylated gold sensor chip for surface plasmon resonance (SPR).

We report the preparation and characterization of a matrix-free carboxylated surface plasmon resonance (SPR) sensor chip with high sensing efficiency by functionalizing a bare gold thin film with a self-assembled monolayer of 16-mercaptohexadecanoic acid (SAM-MHDA chip). The self assembled monolayer surface coverage of the gold layer was carefully evaluated and the SAM was characterized by infrared reflection absorption spectroscopy, X-ray photoemission spectroscopy, atomic force microscopy, X-ray reflectivity-diffraction, and SPR experiments with bovine serum albumin. We compared the SPR signal obtained on this chip made of a dense monolayer of carboxylic acid groups with commercially available carboxylated sensor chips built on the same gold substrate, a matrix-free C1 chip, and a CM5 chip with a ~100 nm dextran hydrogel matrix (GE Healthcare). Two well-studied interaction types were tested, the binding of a biotinylated antibody (immunoglobulin G) to streptavidin and an antigen-antibody interaction. For both interactions, the well characterized densely functionalized SAM-MHDA chip gave a high signal-to-noise ratio and showed a gain in the availability of immobilized ligands for their partners injected in buffer flow. It thus compared favourably with commercially available sensor chips.

Mechanical properties of nanotubes of polyelectrolyte multilayers.

The elastic properties of nanotubes fabricated by layer-by-layer (LbL) assembly of polyelectrolytes in the nanopores of polycarbonate track-etched membranes have been investigated by resonant contact Atomic Force Microscopy (AFM), for nanotube diameters in the range of 100 to 200 nm. The elastic modulus of the nanotubes was computed from the resonance frequencies of a cantilever resting on freely suspended LbL nanotubes. An average value of 115 MPa was found in air for Young's modulus of these nanostructures, well below the values reported for dry, flat multilayers, but in the range of values reported for water-swollen flat multilayers. These low values are most probably due to the lower degree of ionic cross-linking of LbL nanotubes and their consequently higher water content in air, resulting from the peculiar mode of growth of nanoconfined polyelectrolyte multilayers.

Plasmon resonance microsensor for droplet analysis.

Microscale fiber tip sensors based on the plasmon resonance are reported. The fabrication process derived from our previous approach for manufacturing near-field scanning optical microscopy probes has been optimized for sensing applications. A typical tip sensor is a tapered fiber 400 microm in length, coated with a nanoporous thin silver film. The miniaturized geometry of the sensor allows detection in a single droplet of liquid solution (approximately 20 microl). The tip sensor is sensitive for refractive indices between 1.33 and 1.40 with a sensitivity of at least 3 x 10(-4) refractive index unit (RIU)/nm. The Raman scattering enhancement through these microsensors demonstrates the important role played by the localized plasmon resonance. The sensors' linear response covers a large region, interesting for biosensing in aqueous environments such as biomedical applications.

Comparative study of different process steps for the near-field optical probes manufacturing.

This paper deals with different methods for the manufacturing of near-field optical probes with nanometric aperture. After the wet chemical etching of the fiber, two metallization processes are compared: the well-known thermal evaporation versus the novel arrangement of plasma sputtering. Further, it is reported an original controlled nano-indentation in the smooth softness surface to produce the apex aperture of the tapered fiber. These apertures present thin protrusions, but they show good optical and topographic resolutions. Besides, the probe sensitivity is discussed with respect to the multi- and single-mode of the primary optical fiber for imaging sub-wavelength dimension objects in the collection mode.

Raman spectroelectrochemical study of sodium intercalation into poly(p-phenylene).

The structural defects formed along the polymer chain during the electrochemical intercalation of sodium into polyparaphenylene (PPP) were investigated by in situ FT Raman measurements with an excitation wavelength of 1064 nm. Our Raman data are compared with those obtained for PPP and its oligomers intercalated with Na(+) ions by chemical ways. The coexistence of polarons and bipolarons is observed in the early stages of the intercalation process. When the doping level increases polarons are transformed to bipolarons, then in the highly intercalated sample (corresponding to a composition close to Na(0.5)(C(6)H(4))), bipolarons are the main structural defects. This evolution, which is reversible, is in accordance with the electron spin resonance (ESR) data of PPP intercalated with sodium ions in the same experimental conditions.

In-situ spectroscopic investigations of the redox behavior of poly(indole-5-carboxylic-acid) modified electrodes in acidic aqueous solutions.

The oxidation of electrochemically grown poly(indole-5-carboxylic-acid) (P5CO2H) and its spectroscopic properties have been studied by in-situ spectroelectrochemical techniques. The purpose of this paper is to characterize the different modifications on the P5CO2H backbone, induced by the electrochemical oxidation in aqueous acidic solution. We have identified, on the basis of Raman spectra, the vibrational modes associated with neutral and oxidized segments of polymer. It was shown that at least three chemically and optically different species (perhaps other products too) are produced in different potential regimes upon oxidation of this polymer. The results obtained also indicate that the molecular properties of this conducting polymer are better revealed by in-situ resonant spectra than by ex-situ infrared and Raman studies.

UV-vis and Raman spectroelectrochemical investigation of the redox behavior of poly(5-cyanoindole) in acidic aqueous solutions.

Spectroelectrochemical properties of conducting poly(5-cyanoindole) films deposited on indium tin oxide (ITO) and platinum electrodes are investigated using UV-vis and resonant Raman spectroscopies. The transitions from undoped to semi-conducting state of P5CN require the partial oxidation of the polymer to create radical-cations by insertion of charge-neutralizing anions into the polymer. In order to obtain detailed structural information from the vibrational spectra, it is necessary to know the vibrational modes of oxidation-sensitive bands. Vibrational assignments were made on the basis of the results obtained on polyindole and P5CN in acetonitrile solution. The drastic changes in optical absorption and Raman spectra observed at various stage of oxidation were explained by the conversions between at least three different structures. On the basis of the Raman spectra, we have identified the vibrational modes associated with neutral and polaronic segments. The perturbation associated with the coexistence of these polaronic segments has been described as a quinoid structure growing on the expense of the benzoid one. The results obtained indicate that the molecular properties of the conducting polymers at various stages of an oxidation are better revealed by in-situ Raman spectra than by ex-situ studies.