Airway contraction and cytokine release in isolated rat lungs induced by wear particles from the road and tire interface and road vehicle brakes.

The dominant road traffic particle sources are wear particles from the road and tire interface, and from vehicle brake pads. The aim of this work was to investigate the effect of road and brake wear particles on pulmonary function and biomarkers in isolated perfused rat lungs. Particles were sampled from the studded tire wear of three road pavements containing different rock materials in a road simulator; and from the wear of two brake pad materials using a pin-on-disk machine. Isolated rat lungs inhaled the coarse and fine fractions of the sampled particles resulting in an estimated total particle lung dose of 50 µg. The tidal volume (TV) was measured during the particle exposure and the following 50 min. Perfusate and BALF were analyzed for the cytokines TNF, CXCL1 and CCL3. The TV of lungs exposed to rock materials was significantly reduced after 25 min of exposure compared to the controls, for quartzite already after 4 min. The particles of the heavy-duty brake pads had no effect on the TV. Brake particles resulted in a significant elevation of CXCL1 in the perfusate. Brake particles showed significant elevations of all three measured cytokines, and quartzite showed a significant elevation of TNF in BALF. The study shows that the toxic effect on lungs exposed to airborne particles can be investigated using measurements of tidal volume. Furthermore, the study shows that the choice of rock material in road pavements has the potential to affect the toxicity of road wear PM10.

Size-resolved characterization of particles >10 nm emitted to air during metal recycling.

BACKGROUND: In the strive towards a circular economy, metal waste recycling is a growing industry. During the recycling process, particulate matter containing toxic and allergenic metals will be emitted to the air causing unintentional exposure to humans and environment. OBJECTIVE: In this study detailed characterization of particle emissions and workplace exposures were performed, covering the full size range from 10 nm to 10 µm, during recycling of three different material flows: Waste of electrical and electronic equipment (WEEE), metal scrap, and cables. METHODS: Both direct-reading instruments (minute resolution), and time-integrated filter measurements for gravimetric and chemical analysis were used. Additionally, optical sensors were applied and evaluated for long-term online monitoring of air quality in industrial settings. RESULTS: The highest concentrations, in all particle sizes, and with respect both to particle mass and number, were measured in the WEEE flow, followed by the metal scrap flow. The number fraction of nanoparticles was high for all material flows (0.66-0.86). The most abundant metals were Fe, Al, Zn, Pb and Cu. Other elements of toxicological interest were Mn, Ba and Co. SIGNIFICANCE: The large fraction of nanoparticles, and the fact that their chemical composition deviate from that of the coarse particles, raises questions that needs to be further addressed including toxicological implications, both for humans and for the environment.

Effects of cleaning spray use on eyes, airways, and ergonomic load.

BACKGROUND: Cleaning workers are exposed to chemicals and high physical workload, commonly resulting in airway problems and pain. In this study the response in the upper airways and the physical workload following airborne and ergonomic exposure of cleaning spray was investigated. METHODS: A survey was answered by professional cleaning workers to investigate their use of cleaning sprays and the perceived effects on eyes, airways and musculoskeletal pain. A human chamber exposure study was then conducted with 11 professional cleaning workers and 8 non-professional cleaning workers to investigate the airborne exposure, acute effects on eyes and airways, and physical load during cleaning with sprays, foam application and microfiber cloths premoistened with water. All cleaning products used were bleach, chlorine, and ammonia free. The medical assessment included eye and airway parameters, inflammatory markers in blood and nasal lavage, as well as technical recordings of the physical workload. RESULTS: A high frequency of spray use (77%) was found among the 225 professional cleaning workers that answered the survey. Based on the survey, there was an eight times higher risk (p < 0.001) of self-experienced symptoms (including symptoms in the nose, eyes and throat, coughing or difficulty breathing) when they used sprays compared to when they cleaned with other methods. During the chamber study, when switching from spray to foam, the airborne particle and volatile organic compound (VOC) concentrations showed a decrease by 7 and 2.5 times, respectively. For the whole group, the peak nasal inspiratory flow decreased (-10.9 L/min, p = 0.01) during spray use compared to using only water-premoistened microfiber cloths. These effects were lower during foam use (-4.7 L/min, p = 0.19). The technical recordings showed a high physical workload regardless of cleaning with spray or with water. CONCLUSION: Switching from a spraying to a foaming nozzle decreases the exposure of both airborne particles and VOCs, and thereby reduces eye and airway effects, and does not increase the ergonomic load. If the use of cleaning products tested in this study, i.e. bleach, chlorine, and ammonia free, cannot be avoided, foam application is preferable to spray application to improve the occupational environment.

Real-Time Emission and Exposure Measurements of Multi-walled Carbon Nanotubes during Production, Power Sawing, and Testing of Epoxy-Based Nanocomposites.

OBJECTIVES: The use of manufactured nanomaterials is increasing globally. Although multi-walled carbon nanotubes (CNTs) are used in a wide range of applications, only limited data are available on emissions and exposures during CNT composite production. No exposure data using portable aethalometers in the personal breathing zone (PBZ) to monitor occupational exposure to CNTs have yet been published. The aim of this study was to characterize emissions of and exposures to CNTs during CNT composite production, sawing, and shear testing. We also investigated whether real-time aethalometer measurements of equivalent black carbon (eBC) could be used as a proxy filter sampling of elemental carbon (EC). The presence of CNTs as surface contamination in the production facility was monitored since this could contribute to airborne exposure. METHODS: During CNT composite production in an industrial setting including both chemical and manufacturing laboratories, different work tasks (WTs) were studied with a combination of direct-reading instruments (aethalometer, aerodynamic particle sizer, condensation particle counter) and filter-based methods. Measurements were performed to monitor concentrations in the emission zone (EZ), PBZ, and background zone. The filter samples were analysed for EC and fibre concentration of CNTs using scanning electron microscopy (SEM). Additionally, surfaces in the facility were tape sampled for monitoring of CNT contamination, and analysed with SEM. RESULTS: Clear eBC peaks were observed in the PBZ during several WTs, most clearly during open handling of CNT powder. Power sawing emitted the highest particle number concentration in the EZ of both nanoparticles and coarse particles, but no individual airborne CNTs, agglomerates, or aggregates were detected. Airborne CNTs were identified, for example, in a filter sample collected in the PBZ of a worker during mixing of CNT epoxy. The airborne CNT particles were large agglomerates which looked like porous balls in the SEM images. Significant EC exposures were found in the inhalable fraction while all respirable fractions of EC were below detection. The highest inhalable EC concentrations were detected during the composite production. No significant correlation was found between inhalable EC and eBC, most likely due to losses of large EC containing particles in the sampling lines and inside the eBC monitor. In total, 39 tape samples were collected. Surface contamination of CNTs was detected on eight surfaces in the chemical and manufacturing laboratories, mainly in the near-field zone. Elongated CNT-like features were detected in the sawdust after sawing of CNT composite. CONCLUSIONS: Characterization of a workplace producing CNT composite showed that open handling of the CNT powder during weighing and mixing of CNT powder material generated the highest particle emissions and exposures. The portable direct-reading aethalometer provided time-resolved eBC exposure data with complementary information to time-integrated EC filter samples by linking peak exposures to specific WTs. Based on the results it was not possible to conclude that eBC is a good proxy of EC. Surface contamination of CNTs was detected on several surfaces in the near-field zone in the facility. This contamination could potentially be resuspended into the workplace air, and may cause secondary inhalation exposure.

Lung function and self-rated symptoms in healthy volunteers after exposure to hydrotreated vegetable oil (HVO) exhaust with and without particles.

BACKGROUND: Diesel engine exhaust causes adverse health effects. Meanwhile, the impact of renewable diesel exhaust, such as hydrotreated vegetable oil (HVO), on human health is less known. Nineteen healthy volunteers were exposed to HVO exhaust for 3 h in a chamber with a double-blind, randomized setup. Exposure scenarios comprised of HVO exhaust from two modern non-road vehicles with 1) no aftertreatment system ('HVOPM+NOx' PM1: 93 µg m-3, EC: 54 µg m-3, NO: 3.4 ppm, NO2: 0.6 ppm), 2) an aftertreatment system containing a diesel oxidation catalyst and a diesel particulate filter ('HVONOx' PM1: ~ 1 µg m-3, NO: 2.0 ppm, NO2: 0.7 ppm) and 3) filtered air (FA) as control. The exposure concentrations were in line with current EU occupational exposure limits (OELs) of NO, NO2, formaldehyde, polycyclic aromatic hydrocarbons (PAHs), and the future OEL (2023) of elemental carbon (EC). The effect on nasal patency, pulmonary function, and self-rated symptoms were assessed. Calculated predicted lung deposition of HVO exhaust particles was compared to data from an earlier diesel exhaust study. RESULTS: The average total respiratory tract deposition of PM1 during HVOPM+NOx was 27 µg h-1. The estimated deposition fraction of HVO PM1 was 40-50% higher compared to diesel exhaust PM1 from an older vehicle (earlier study), due to smaller particle sizes of the HVOPM+NOx exhaust. Compared to FA, exposure to HVOPM+NOx and HVONOx caused higher incidence of self-reported symptoms (78%, 63%, respectively, vs. 28% for FA, p < 0.03). Especially, exposure to HVOPM+NOx showed 40-50% higher eye and throat irritation symptoms. Compared to FA, a decrement in nasal patency was found for the HVONOx exposures (- 18.1, 95% CI: - 27.3 to - 8.8 L min-1, p < 0.001), and for the HVOPM+NOx (- 7.4 (- 15.6 to 0.8) L min-1, p = 0.08). Overall, no clinically significant change was indicated in the pulmonary function tests (spirometry, peak expiratory flow, forced oscillation technique). CONCLUSION: Short-term exposure to HVO exhaust concentrations corresponding to EU OELs for one workday did not cause adverse pulmonary function changes in healthy subjects. However, an increase in self-rated mild irritation symptoms, and mild decrease in nasal patency after both HVO exposures, may indicate irritative effects from exposure to HVO exhaust from modern non-road vehicles, with and without aftertreatment systems.

Toxicological effects of zinc oxide nanoparticle exposure: an in vitro comparison between dry aerosol air-liquid interface and submerged exposure systems.

Engineered nanomaterials (ENMs) are increasingly produced and used today, but health risks due to their occupational airborne exposure are incompletely understood. Traditionally, nanoparticle (NP) toxicity is tested by introducing NPs to cells through suspension in the growth media, but this does not mimic respiratory exposures. Different methods to introduce aerosolized NPs to cells cultured at the air-liquid-interface (ALI) have been developed, but require specialized equipment and are associated with higher cost and time. Therefore, it is important to determine whether aerosolized setups induce different cellular responses to NPs than traditional ones, which could provide new insights into toxicological responses of NP exposure. This study evaluates the response of human alveolar epithelial cells (A549) to zinc oxide (ZnO) NPs after dry aerosol exposure in the Nano Aerosol Chamber for In Vitro Toxicity (NACIVT) system as compared to conventional, suspension-based exposure: cells at ALI or submerged. Similar to other studies using nebulization of ZnO NPs, we found that dry aerosol exposure of ZnO NPs via the NACIVT system induced different cellular responses as compared to conventional methods. ZnO NPs delivered at 1.0 µg/cm2 in the NACIVT system, mimicking occupational exposure, induced significant increases in metabolic activity and release of the cytokines IL-8 and MCP-1, but no differences were observed using traditional exposures. While factors associated with the method of exposure, such as differing NP aggregation, may contribute toward the different cellular responses observed, our results further encourage the use of more physiologically realistic exposure systems for evaluating airborne ENM toxicity.

Emissions and exposures of graphene nanomaterials, titanium dioxide nanofibers, and nanoparticles during down-stream industrial handling.

Today, engineered nanomaterials are frequently used. Nanosized titanium dioxide (TiO2) has been extensively used for many years and graphene is one type of emerging nanomaterial. Occupational airborne exposures to engineered nanomaterials are important to ensure safe workplaces and to extend the information needed for complete risk assessments. The main aim of this study was to characterize workplace emissions and exposure of graphene nanoplatelets, graphene oxide, TiO2 nanofibers (NFs) and nanoparticles (NPs) during down-stream industrial handling. Surface contaminations were also investigated to assess the potential for secondary inhalation exposures. In addition, a range of different sampling and aerosol monitoring methods were used and evaluated. The results showed that powder handling, regardless of handling graphene nanoplatelets, graphene oxide, TiO2 NFs, or NPs, contributes to the highest particle emissions and exposures. However, the exposure levels were below suggested occupational exposure limits. It was also shown that a range of different methods can be used to selectively detect and quantify nanomaterials both in the air and as surface contaminations. However, to be able to make an accurate determination of which nanomaterial that has been emitted a combination of different methods, both offline and online, must be used.

Workplace Emissions and Exposures During Semiconductor Nanowire Production, Post-production, and Maintenance Work.

BACKGROUND: Nanowires are a high-aspect-ratio material of increasing interest for a wide range of applications. A new and promising method to produce nanowires is by aerotaxy, where the wires are grown in a continuous stream of gas. The aerotaxy method can grow nanowires much faster than by more conventional methods. Nanowires have important properties in common with asbestos fibers, which indicate that there can be potential health effects if exposure occurs. No conclusive exposure (or emission) data from aerotaxy-production of nanowires has so far been published. METHODS: Different work tasks during semiconductor nanowire production, post-production, and maintenance were studied. A combination of direct-reading instruments for number concentration (0.007-20 µm) and filter sampling was used to assess the emissions (a couple of centimeter from the emission sources), the exposure in the personal breathing zone (max 30 cm from nose-mouth), and the concentrations in the background zone (at least 3 m from any emission source). The filters were analyzed for metal dust composition and number concentration of nanowires. Various surfaces were sampled for nanowire contamination. RESULTS: The particle concentrations in the emission zone (measured with direct-reading instruments) were elevated during cleaning of arc discharge, manual reactor cleaning, exchange of nanowire outflow filters, and sonication of substrates with nanowires. In the case of cleaning of the arc discharge and manual reactor cleaning, the emissions affected the concentrations in the personal breathing zone and were high enough to also affect the concentrations in the background. Filter analysis with electron microscopy could confirm the presence of nanowires in some of the air samples. CONCLUSIONS: Our results show that a major part of the potential for exposure occurs not during the actual manufacturing, but during the cleaning and maintenance procedures. The exposures and emissions were evaluated pre- and post-upscaling the production and showed that some work tasks (e.g. exchange of nanowire outflow filters and sonication of substrates with nanowires) increased the emissions post-upscaling.

Characterization of airborne particles from cleaning sprays and their corresponding respiratory deposition fractions.

Cleaning workers are exposed to many risk factors, including handling of cleaning products. Epidemiological studies show that they have a high incidence of asthma and other respiratory symptoms. Some studies have indicated an even higher incidence of asthma in individuals using cleaning sprays regularly. It is known that sprays produce an aerosol that can expose the respiratory system to chemicals. Knowledge of the physical characteristics of the airborne particles, as well as the characteristics of the gas phase, is needed to determine how they affect the respiratory tract and why they cause airway symptoms. The aim of this study was to characterize the aerosols from seven different ready-to-use trigger cleaning sprays in terms of total airborne mass fraction, particle size distribution, and new particle formation from ozone reactions. An additional aim was to calculate the respiratory deposition fraction of the measured particles. The total airborne mass fraction was determined by comparing the mass deposited on the chamber wall with the mass emitted from the bottle during spraying. Particle number concentration and size distribution of the airborne particles were measured using an aerodynamic particle sizer and a fast aerosol mobility size spectrometer. The total airborne mass fraction was between 2.7% and 32.2% of the mass emitted from the bottle, depending on the product. Between 0.0001% and 0.01% of the total airborne mass fraction consisted of residual particles. However, these particles had a mass median aerodynamic diameter between 1.9 µm and 3.7 µm, constituting a total respiratory deposition of up to 77%. New particle formation in the presence of ozone was also shown to vary between 5,000 cm-3 and 35,000 cm-3 depending on the product, in the studied settings. These findings confirm that a substantial part (up to 1/3) of the mass sprayed from the bottle does not reach the intended surface. Thus, the use of cleaning sprays can result in chemical airway exposure, with particles in the relevant size range for both nasal and alveolar deposition.