Iterative Bragg peak removal on X-ray absorption spectra with automatic intensity correction.

This study introduces a novel iterative Bragg peak removal with automatic intensity correction (IBR-AIC) methodology for X-ray absorption spectroscopy (XAS), specifically addressing the challenge of Bragg peak interference in the analysis of crystalline materials. The approach integrates experimental adjustments and sophisticated post-processing, including an iterative algorithm for robust calculation of the scaling factor of the absorption coefficients and efficient elimination of the Bragg peaks, a common obstacle in accurately interpreting XAS data, particularly in crystalline samples. The method was thoroughly evaluated on dilute catalysts and thin films, with fluorescence mode and large-angle rotation. The results underscore the technique's effectiveness, adaptability and substantial potential in improving the precision of XAS data analysis. While demonstrating significant promise, the method does have limitations related to signal-to-noise ratio sensitivity and the necessity for meticulous angle selection during experimentation. Overall, IBR-AIC represents a significant advancement in XAS, offering a pragmatic solution to Bragg peak contamination challenges, thereby expanding the applications of XAS in understanding complex materials under diverse experimental conditions.

Enhanced Mechanical and Electromechanical Properties of Compositionally Complex Zirconia Zr1-x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ Ceramics.

Compositionally complex oxides (CCOs) or high-entropy oxides (HEOs) are new multielement oxides with unexplored physical and functional properties. In this work, we report fluorite structure-derived compositionally complex zirconia with composition Zr1-x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ (x = 0.1 and 0.2) synthesized in solid-state reaction route and sintered via hot pressing at 1350 °C. We explore the evolution of these oxides' structural, microstructural, mechanical, electrical, and electromechanical properties regarding phase separation and sintering mechanisms. Highly dense ceramics are achieved by bimodal mass diffusion, composing nanometric tetragonal and micrometric cubic grains microstructure. The material exhibits an anomalously large electrostriction response exceeding the M33 value of 10-17 m2/V2 at room temperature and viscoelastic properties of primary creep in nanoindentation measurement under fast loading. These findings are strikingly similar to those reported for doped ceria and bismuth oxide derivates, highlighting the presence of a large concentration of point defects linked to structural distortion and anelastic behavior, which are characteristics of nonclassical ionic electrostrictors.

Local Environment of Sc and Y Dopant Ions in Aluminum Nitride Thin Films.

The local environments of Sc and Y in predominantly ⟨002⟩ textured, Al1-xDoxN (Do = Sc, x = 0.25, 0.30 or Y, x = 0.25) sputtered thin films with wurtzite symmetry were investigated using X-ray absorption (XAS) and photoelectron (XPS) spectroscopies. We present evidence from the X-ray absorption fine structure (XAFS) spectra that, when x = 0.25, both Sc3+ and Y3+ ions are able to substitute for Al3+, thereby acquiring four tetrahedrally coordinated nitrogen ligands, i.e., coordination number (CN) of 4. On this basis, the crystal radius of the dopant species in the wurtzite lattice, not available heretofore, could be calculated. By modeling the scandium local environment, extended XAFS (EXAFS) analysis suggests that when x increases from 0.25 to 0.30, CN for a fraction of the Sc ions increases from 4 to 6, signaling octahedral coordination. This change occurs at a dopant concentration significantly lower than the reported maximum concentration of Sc (42 mol % Sc) in wurtzite (Al, Sc)N. XPS spectra provide support for our observation that the local environment of Sc in (Al, Sc)N may include more than one type of coordination.

The elastic component of anisotropic strain dominates the observed shift in the F2g Raman mode of anelastic ceria thin films.

Raman spectroscopy is applied for non-destructive characterization of strain in crystalline thin films. The analysis makes use of the numerical value of the mode Grüneisen parameter γ, which relates the fractional change in the frequency of a Raman-active vibrational mode and the strain-induced fractional change in the unit cell volume. When in-plane, compressive biaxial strain in aliovalent doped CeO2-films is relieved by partial substrate removal, the films exhibit values of γ for the F2g vibrational mode which are ∼30% of the literature values for bulk ceramics under isostatic stress. This discrepancy has been attributed to a negative contribution from the anelastic (time-dependent) mechanical properties of aliovalent-doped ceria. Here we propose a way to "separate" anelastic and elastic contributions to the F2g mode Grüneisen parameter. Mechanically elastic yttria (Y2O3) films on Ti/SiO2/Si substrate serve as "control". The values of γ calculated from the change in frequency of the ∼375 cm-1 F2g Raman-active mode are close to the literature values for bulk yttria under isostatic stress. This work should serve to provide a protocol for characterization of selective sensitivity to different strain components of doped ceria thin films.

Lead-free Zr-doped ceria ceramics with low permittivity displaying giant electrostriction.

Electrostrictors, materials developing mechanical strain proportional to the square of the applied electric field, present many advantages for mechanical actuation as they convert electrical energy into mechanical, but not vice versa. Both high relative permittivity and reliance on Pb as the key component in commercial electrostrictors pose serious practical and health problems. Here we describe a low relative permittivity (<250) ceramic, ZrxCe1-xO2 (x < 0.2), that displays electromechanical properties rivaling those of the best performing electrostrictors: longitudinal electrostriction strain coefficient ~10-16 m2/V2; relaxation frequency ≈ a few kHz; and strain ≥0.02%. Combining X-ray absorption spectroscopy, atomic-level modeling and electromechanical measurements, here we show that electrostriction in ZrxCe1-xO2 is enabled by elastic dipoles produced by anharmonic motion of the smaller isovalent dopant (Zr). Unlike the elastic dipoles in aliovalent doped ceria, which are present even in the absence of an applied elastic or electric field, the elastic dipoles in ZrxCe1-xO2 are formed only under applied anisotropic field. The local descriptors of electrostrictive strain, namely, the cation size mismatch and dynamic anharmonicity, are sufficiently versatile to guide future searches in other polycrystalline solids.

Electro-Freezing of Supercooled Water Is Induced by Hydrated Al3+ and Mg2+ Ions: Experimental and Theoretical Studies.

This work reports that the octahedral hydrated Al3+ and Mg2+ ions operate within electrolytic cells as kosmotropic (long-range order-making) "ice makers" of supercooled water (SCW). 10-5 M solutions of hydrated Al3+ and Mg2+ ions each trigger, near the cathode (-20 ± 5 V), electro-freezing of SCW at -4 °C. The hydrated Al3+ ions do so with 100% efficiency, whereas the Mg2+ ions induce icing with 40% efficiency. In contrast, hydrated Na+ ions, under the same experimental conditions, do not induce icing differently than pure water. As such, our study shows that the role played by Al3+ and Mg2+ ions in water electro-freezing is impacted by two synchronous effects: (1) a geometric effect due to the octahedral packing of the coordinated water molecules around the metallic ions, and (2) the degree of polarization which these two ions induce and thereby acidify the coordinated water molecules, which in turn imparts them with an ice-like structure. Long-duration molecular dynamics (MD) simulations of the Al3+ and Mg2+ indeed reveal the formation of "ice-like" hexagons in the vicinity of these ions. Furthermore, the MD shows that these hexagons and the electric fields of the coordinate water molecules give rise to ultimate icing. As such, the MD simulations provide a rational explanation for the order-making properties of these ions during electro-freezing.

Phase segregation and miscibility of TiOx nanocomposites in Gd-doped ceria solid electrolyte material.

Electro-chemo-mechanical (ECM) coupling refers to mechanical deformation due to electrochemically driven compositional change in a solid. An ECM actuator producing micrometre-size displacements and long-term stability at room temperature was recently reported, comprising a 20 mol% Gd-doped ceria (20GDC), a solid electrolyte membrane, placed between two working bodies made of TiOx/20GDC (Ti-GDC) nanocomposites with Ti concentration of 38 mol%. The volumetric changes originating from oxidation or reduction in the local TiOx units are hypothesized to be the origin of mechanical deformation in the ECM actuator. Studying the Ti concentration-dependent structural changes in the Ti-GDC nanocomposites is therefore required for (i) understanding the mechanism of dimensional changes in the ECM actuator and (ii) maximizing the ECM response. Here, the systematic investigation of the local structure of the Ti and Ce ions in Ti-GDC over a broad range of Ti concentrations using synchrotron X-ray absorption spectroscopy and X-ray diffraction is reported. The main finding is that, depending on the Ti concentration, Ti atoms either form a cerium titanate or segregate into a TiO2 anatase-like phase. The transition region between these two regimes with Ti(IV) concentration between 19% and 57% contained strongly disordered TiOx units dispersed in 20GDC containing Ce(III) and Ce(IV) and hence rich with oxygen vacancies. As a result, this transition region is proposed to be the most advantageous for developing ECM-active materials.

Engineering of Pyroelectric Crystals Decoupled from Piezoelectricity as Illustrated by Doped α-Glycine.

Design of pyroelectric crystals decoupled from piezoelectricity is not only a topic of scientific curiosity but also demonstrates effects in principle that have the potential to be technologically advantageous. Here we report a new method for the design of such materials. Thus, the co-doping of centrosymmetric crystals with tailor-made guest molecules, as illustrated by the doping of α-glycine with different amino acids (Threonine, Alanine and Serine). The polarization of those crystals displays two distinct contributions, one arising from the difference in dipole moments between guest and host and the other from the displacement of host molecules from their symmetry-related positions. These contributions exhibit different temperature dependences and response to mechanical deformation. Thus, providing a proof of concept for the ability to design pyroelectric materials with reduced piezoelectric coefficient (d22 ) to a minimal value, below the resolution limit of the method (<0.005 pm/V).

C-Axis Textured, 2-3 µm Thick Al0.75Sc0.25N Films Grown on Chemically Formed TiN/Ti Seeding Layers for MEMS Applications.

A protocol for successfully depositing [001] textured, 2−3 µm thick films of Al0.75Sc0.25N, is proposed. The procedure relies on the fact that sputtered Ti is [001]-textured α-phase (hcp). Diffusion of nitrogen ions into the α-Ti film during reactive sputtering of Al0.75,Sc0.25N likely forms a [111]-oriented TiN intermediate layer. The lattice mismatch of this very thin film with Al0.75Sc0.25N is ~3.7%, providing excellent conditions for epitaxial growth. In contrast to earlier reports, the Al0.75Sc0.25N films prepared in the current study are Al-terminated. Low growth stress (<100 MPa) allows films up to 3 µm thick to be deposited without loss of orientation or decrease in piezoelectric coefficient. An advantage of the proposed technique is that it is compatible with a variety of substrates commonly used for actuators or MEMS, as demonstrated here for both Si wafers and D263 borosilicate glass. Additionally, thicker films can potentially lead to increased piezoelectric stress/strain by supporting application of higher voltage, but without increase in the magnitude of the electric field.

Atomically engineered interfaces yield extraordinary electrostriction.

Electrostriction is a property of dielectric materials whereby an applied electric field induces a mechanical deformation proportional to the square of that field. The magnitude of the effect is usually minuscule (<10-19 m2 V-2 for simple oxides). However, symmetry-breaking phenomena at the interfaces can offer an efficient strategy for the design of new properties1,2. Here we report an engineered electrostrictive effect via the epitaxial deposition of alternating layers of Gd2O3-doped CeO2 and Er2O3-stabilized δ-Bi2O3 with atomically controlled interfaces on NdGaO3 substrates. The value of the electrostriction coefficient achieved is 2.38 × 10-14 m2 V-2, exceeding the best known relaxor ferroelectrics by three orders of magnitude. Our theoretical calculations indicate that this greatly enhanced electrostriction arises from coherent strain imparted by interfacial lattice discontinuity. These artificial heterostructures open a new avenue for the design and manipulation of electrostrictive materials and devices for nano/micro actuation and cutting-edge sensors.

Chemical Nature of Heterogeneous Electrofreezing of Supercooled Water Revealed on Polar (Pyroelectric) Surfaces.

ConspectusThe ability to control the icing temperature of supercooled water (SCW) is of supreme importance in subfields of pure and applied sciences. The ice freezing of SCW can be influenced heterogeneously by electric effects, a process known as electrofreezing. This effect was first discovered during the 19th century; however, its mechanism is still under debate. In this Account we demonstrate, by capitalizing on the properties of polar crystals, that heterogeneous electrofreezing of SCW is a chemical process influenced by an electric field and specific ions. Polar crystals possess a net dipole moment. In addition, they are pyroelectric, displaying short-lived surface charges at their hemihedral faces at the two poles of the crystals as a result of temperature changes. Accordingly, during cooling or heating, an electric field is created, which is negated by the attraction of compensating charges from the environment. This process had an impact in the following experiments. The icing temperatures of SCW within crevices of polar crystals are higher in comparison to icing temperatures within crevices of nonpolar analogs. The role played by the electric effect was extricated from other effects by the performance of icing experiments on the surfaces of pyroelectric quasi-amorphous SrTiO3. During those studies it was found that on positively charged surfaces the icing temperature of SCW is elevated, whereas on negatively charged surfaces it is reduced. Following investigations discovered that the icing temperature of SCW is impacted by an ionic current created within a hydrated layer on top of hydrophilic faces residing parallel to the polar axes of the crystals. In the absence of such current on analogous hydrophobic surfaces, the pyroelectric effect does not influence the icing temperature of SCW. Those results implied that electrofreezing of SCW is a process influenced by specific compensating ions attracted by the pyroelectric field from the aqueous solution. When freezing experiments are performed in an open atmosphere, bicarbonate and hydronium ions, created by the dissolution of atmospheric CO2 in water, influence the icing temperature. The bicarbonate ions, when attracted by positively charged pyroelectric surfaces, elevate the icing temperature, whereas their counterparts, hydronium ions, when attracted by the negatively charged surfaces reduce the icing temperature. Molecular dynamic simulations suggested that bicarbonate ions, concentrated within the near positively charged interfacial layer, self-assemble with water molecules to create stabilized slightly distorted "ice-like" hexagonal assemblies which mimic the hexagons of the crystals of ice. This occurs by replacing, within those ice-like hexagons, two hydrogen bonds of water by C-O bonds of the HCO3- ion. On the basis of these simulations, it was predicted and experimentally confirmed that other trigonal planar ions such as NO3-, guanidinium+, and the quasi-hexagonal biguanidinium+ ion elevate the icing temperature. These ions were coined as "ice makers". Other ions including hydronium, Cl-, and SO4-2 interfere with the formation of ice-like assemblies and operate as "ice breakers". The higher icing temperatures induced within the crevices of the hydrophobic polar crystals in comparison to the nonpolar analogs can be attributed to the proton ordering of the water molecules. In contrast, the icing temperatures on related hydrophilic surfaces are influenced both by compensating charges and by proton ordering.

Local Piezoelectric Properties of Doped Biomolecular Crystals.

Piezoelectricity is the ability of certain crystals to generate mechanical strain proportional to an external electric field. Though many biomolecular crystals contain polar molecules, they are frequently centrosymmetric, signifying that the dipole moments of constituent molecules cancel each other. However, piezoelectricity can be induced by stereospecific doping leading to symmetry reduction. Here, we applied piezoresponse force microscopy (PFM), highly sensitive to local piezoelectricity, to characterize (01¯0) faces of a popular biomolecular material, α-glycine, doped with other amino acids such as L-alanine and L-threonine as well as co-doped with both. We show that, while apparent vertical piezoresponse is prone to parasitic electrostatic effects, shear piezoelectric activity is strongly affected by doping. Undoped α-glycine shows no shear piezoelectric response at all. The shear response of the L-alanine doped crystals is much larger than those of the L-threonine doped crystals and co-doped crystals. These observations are rationalized in terms of host-guest molecule interactions.

Comparative analysis of XANES and EXAFS for local structural characterization of disordered metal oxides.

In functional materials, the local environment around active species that may contain just a few nearest-neighboring atomic shells often changes in response to external conditions. Strong disorder in the local environment poses a challenge to commonly used extended X-ray absorption fine structure (EXAFS) analysis. Furthermore, the dilute concentrations of absorbing atoms, small sample size and the constraints of the experimental setup often limit the utility of EXAFS for structural analysis. X-ray absorption near-edge structure (XANES) has been established as a good alternative method to provide local electronic and geometric information of materials. The pre-edge region in the XANES spectra of metal compounds is a useful but relatively under-utilized resource of information of the chemical composition and structural disorder in nano-materials. This study explores two examples of materials in which the transition metal environment is either relatively symmetric or strongly asymmetric. In the former case, EXAFS results agree with those obtained from the pre-edge XANES analysis, whereas in the latter case they are in a seeming contradiction. The two observations are reconciled by revisiting the limitations of EXAFS in the case of a strong, asymmetric bond length disorder, expected for mixed-valence oxides, and emphasize the utility of the pre-edge XANES analysis for detecting local heterogeneities in structural and compositional motifs.

Trivalent Dopant Size Influences Electrostrictive Strain in Ceria Solid Solutions.

The technologically important frequency range for the application of electrostrictors and piezoelectrics is tens of Hz to tens of kHz. Sm3+- and Gd3+-doped ceria ceramics, excellent intermediate-temperature ion conductors, have been shown to exhibit very large electrostriction below 1 Hz. Why this is so is still not understood. While optimal design of ceria-based devices requires an in-depth understanding of their mechanical and electromechanical properties, systematic investigation of the influence of dopant size on frequency response is lacking. In this report, the mechanical and electromechanical properties of dense ceria ceramics doped with trivalent lanthanides (RE0.1Ce0.9O1.95, RE = Lu, Yb, Er, Gd, Sm, and Nd) were investigated. Young's, shear, and bulk moduli were obtained from ultrasound pulse echo measurements. Nanoindentation measurements revealed room-temperature creep in all samples as well as the dependence of Young's modulus on the unloading rate. Both are evidence for viscoelastic behavior, in this case anelasticity. For all samples, within the frequency range f = 0.15-150 Hz and electric field E ≤ 0.7 MV/m, the longitudinal electrostriction strain coefficient (|M33|) was 102 to 104-fold larger than expected for classical (Newnham) electrostrictors. However, electrostrictive strain in Er-, Gd-, Sm-, and Nd-doped ceramics exhibited marked frequency relaxation, with the Debye-type characteristic relaxation time τ ≤ 1 s, while for the smallest dopants-Lu and Yb-little change in electrostrictive strain was detected over the complete frequency range studied. We find that only the small, less-studied dopants continue to produce useable electrostrictive strain at the higher frequencies. We suggest that this striking difference in frequency response may be explained by postulating that introduction of a dopant induces two types of polarizable elastic dipoles and that the dopant size determines which of the two will be dominant.

Surface Piezoelectricity and Pyroelectricity in Centrosymmetric Materials: A Case of α-Glycine.

Surface pyroelectricity and piezoelectricity induced by water incorporation during growth in α-glycine were investigated. Using the periodic temperature change technique, we have determined the thickness (~280 µm) of the near surface layer (NSL) and its pyroelectric coefficient (160 pC/(K × cm2) at 23 °C) independently. The thickness of NSL remains nearly constant till 60 °C and the pyroelectric effect vanishes abruptly by 70 °C. The piezoelectric effect, 0.1 pm/V at 23 °C measured with an interferometer, followed the same temperature dependence as the pyroelectric effect. Abrupt disappearance of both effects at 70 °C is irreversible and suggests that water incorporation to α-glycine forms a well defined near surface phase, which is different form α-glycine because it is polar but it too close to α-glycine to be distinguished by X-ray diffraction (XRD). The secondary pyroelectric effect was found to be <14% of the total, which is unexpectedly small for a material with a large thermal expansion coefficient. This implies that water incorporation infers minimal distortions in the host lattice. This finding suggests a path for the control of the piezoelectric and pyroelectric effects of the crystals using stereospecific incorporation of the guest molecules.

Dopant Concentration Controls Quasi-Static Electrostrictive Strain Response of Ceria Ceramics.

Electromechanically active ceramic materials, piezoelectrics and electrostrictors, provide the backbone of a variety of consumer technologies. Gd- and Sm-doped ceria are ion conducting ceramics, finding application in fuel cells, oxygen sensors, and, potentially, as memristor materials. While optimal design of ceria-based devices requires a thorough understanding of their mechanical and electromechanical properties, reports of systematic study of the effect of dopant concentration on the electromechanical behavior of ceria-based ceramics are lacking. Here we report the longitudinal electrostriction strain coefficient (M33) of dense RExCe1-xO2-x/2 (x ≤ 0.25) ceramic pellets, where RE = Gd or Sm, measured under ambient conditions as a function of dopant concentration within the frequency range f = 0.15-350 Hz and electric field amplitude E ≤ 0.5 MV/m. For >100 Hz, all ceramic pellets tested, independent of dopant concentration, exhibit longitudinal electrostriction strain coefficient with magnitude on the order of 10-18 m2/V2. The quasi-static (f < 1 Hz) electrostriction strain coefficient for undoped ceria is comparable in magnitude, while introducing 5 mol % Gd or 5 mol % Sm produces an increase in M33 by up to 2 orders of magnitude. For x ≤ 0.1 (Gd)-0.15 (Sm), the Debye-type relaxation time constant (τ) is in the range 60-300 ms. The inverse relationship between dopant concentration and quasi-static electrostrictive strain parallels the anelasticity and ionic conductivity of Gd- and Sm-doped ceria ceramics, indicating that electrostriction is partially governed by ordering of vacancies and changes in local symmetry.

Heterogeneous Electrofreezing of Super-Cooled Water on Surfaces of Pyroelectric Crystals is Triggered by Trigonal Planar Ions.

Electrofreezing experiments of super-cooled water (SCW) with different ions, performed directly on the charged hemihedral faces of pyroelectric LiTaO3 and AgI crystals, in the presence and in the absence of pyroelectric charge are reported. It is demonstrated that bicarbonate (HCO3 - ) ions elevate the icing temperature near the positively charged faces. In contrast, the hydronium (H3 O+ ) slightly reduces the icing temperature. Molecular dynamics simulations suggest that the hydrated trigonal planar HCO3 - ions self-assemble with water molecules near the surface of the AgI crystal as clusters of slightly different configuration from those of the ice-like hexagons. These clusters, however, have a tendency to serve as embryonic nuclei for ice crystallization. Consequently, we predicted and experimentally confirmed that the trigonal planar ions of NO3 - and guanidinium (Gdm+ ), at appropriate concentrations, elevate the icing temperature near the positive and negative charged surfaces, respectively. On the other hand, the Cl- and SO4 2- ions of different configurations reduce the icing temperature.

Heterogeneous Electrofreezing Triggered by CO2 on Pyroelectric Crystals: Qualitatively Different Icing on Hydrophilic and Hydrophobic Surfaces.

By performing icing experiments on hydrophilic and hydrophobic surfaces of pyroelectric amino acids and on the x-cut faces of LiTaO3 , we discovered that the effect of electrofreezing of super cooled water is triggered by ions of carbonic acid. During the cooling of the hydrophilic pyroelectric crystals, a continuous water layer is created between the charged hemihedral faces, as confirmed by impedance measurements. As a result, a current of carbonic acid ions, produced by dissolved environmental CO2 , flows through the wetted layer towards the hemihedral faces and elevates the icing temperature. This proposed mechanism is based on the following: (i) on hydrophilic surfaces, water with dissolved CO2 (pH 4) freezes at higher temperatures than pure water of pH 7. (ii) In the absence of the ionic current, achieved by linking the two hemihedral faces of hydrophilic crystals by a conductive paint, water of the two pH levels freeze at the same temperature. (iii) On hydrophobic crystals with similar pyroelectric coefficients, where there is no continuous wetted layer, no electrofreezing effect is observed.

A review of defect structure and chemistry in ceria and its solid solutions.

Ceria and its solid solutions play a vital role in several industrial processes and devices. These include solar energy-to-fuel conversion, solid oxide fuel and electrolyzer cells, memristors, chemical looping combustion, automotive 3-way catalysts, catalytic surface coatings, supercapacitors and recently, electrostrictive devices. An attractive feature of ceria is the possibility of tuning defect-chemistry to increase the effectiveness of the materials in application areas. Years of study have revealed many features of the long-range, macroscopic characteristics of ceria and its derivatives. In this review we focus on an area of ceria defect chemistry which has received comparatively little attention - defect-induced local distortions and short-range associates. These features are non-periodic in nature and hence not readily detected by conventional X-ray powder diffraction. We compile the relevant literature data obtained by thermodynamic analysis, Raman spectroscopy, and X-ray absorption fine structure (XAFS) spectroscopy. Each of these techniques provides insight into material behavior without reliance on long-range periodic symmetry. From thermodynamic analyses, association of defects is inferred. From XAFS, an element-specific probe, local structure around selected atomic species is obtained, whereas from Raman spectroscopy, local symmetry breaking and vibrational changes in bonding patterns is detected. We note that, for undoped ceria and its solid solutions, the relationship between short range order and cation-oxygen-vacancy coordination remains a subject of active debate. Beyond collating the sometimes contradictory data in the literature, we strengthen this review by reporting new spectroscopy results and analysis. We contribute to this debate by introducing additional data and analysis, with the expectation that increasing our fundamental understanding of this relationship will lead to an ability to predict and tailor the defect-chemistry of ceria-based materials for practical applications.

Surface Pyroelectricity in Cubic SrTiO3.

Symmetry-imposed restrictions on the number of available pyroelectric and piezoelectric materials remain a major limitation as 22 out of 32 crystallographic material classes exhibit neither pyroelectricity nor piezoelectricity. Yet, by breaking the lattice symmetry it is possible to circumvent this limitation. Here, using a unique technique for measuring transient currents upon rapid heating, direct experimental evidence is provided that despite the fact that bulk SrTiO3 is not pyroelectric, the (100) surface of TiO2 -terminated SrTiO3 is intrinsically pyroelectric at room temperature. The pyroelectric layer is found to be ≈1 nm thick and, surprisingly, its polarization is comparable with that of strongly polar materials such as BaTiO3 . The pyroelectric effect can be tuned ON/OFF by the formation or removal of a nanometric SiO2 layer. Using density functional theory, the pyroelectricity is found to be a result of polar surface relaxation, which can be suppressed by varying the lattice symmetry breaking using a SiO2 capping layer. The observation of pyroelectricity emerging at the SrTiO3 surface also implies that it is intrinsically piezoelectric. These findings may pave the way for observing and tailoring piezo- and pyroelectricity in any material through appropriate breaking of symmetry at surfaces and artificial nanostructures such as heterointerfaces and superlattices.