Synthesis of 5-(Aryl)amino-1,2,3-triazole-containing 2,1,3-Benzothiadiazoles via Azide-Nitrile Cycloaddition Followed by Buchwald-Hartwig Reaction.

An efficient access to the novel 5-(aryl)amino-1,2,3-triazole-containing 2,1,3-benzothiadiazole derivatives has been developed. The method is based on 1,3-dipolar azide-nitrile cycloaddition followed by Buchwald-Hartwig cross-coupling to afford the corresponding N-aryl and N,N-diaryl substituted 5-amino-1,2,3-triazolyl 2,1,3-benzothiadiazoles under NHC-Pd catalysis. The one-pot diarylative Pd-catalyzed heterocyclization opens the straightforward route to triazole-linked carbazole-benzothiadiazole D-A systems. The optical and electrochemical properties of the compound obtained were investigated to estimate their potential application as emissive layers in OLED devises. The quantum yield of photoluminescence (PLQY) of the synthesized D-A derivatives depends to a large extent on electron-donating strengths of donor (D) component, reaching in some cases the values closed to 100%. Based on the most photoactive derivative and wide bandgap host material mCP, a light-emitting layer of OLED was made. The device showed a maximum brightness of 8000 cd/m2 at an applied voltage of 18 V. The maximum current efficiency of the device reaches a value of 3.29 cd/A.

Charge Carrier Mobility in Poly(N,N'-bis-4-butylphenyl-N,N'-bisphenyl)benzidine Composites with Electron Acceptor Molecules.

Polymer composites based on poly(N,N'-bis-4-butylphenyl-N,N'-bisphenyl)benzidine (poly-TPD) with PCBM and copper(II) pyropheophorbide derivative (Cu-PP) were developed. In thin films of the poly-TPD and Cu-PP composites, the charge carrier mobility was investigated for the first time. In the ternary poly-TPD:PCBM:Cu-PP composite, the electron and hole mobilities are the most balanced compared to binary composites and the photoconductivity is enhanced due to the sensitization by Cu-PP in blue and red spectral ranges. The new composites are promising for use in the development of photodetectors.

Photoconduction and Electroluminescence of Copper (II) Protoporphyrin and Chlorin Cu-C-e6.

Cu (II) protoporphyrin Cu-PP-IX and chlorin Cu-C-e6 were found to have both thin solid film formation and charge carrier transport abilities. In the layers deposited by resistive thermal evaporation, the mobilities of holes and electrons are on the order of 10-5 cm2 V-1 s-1. Organic light-emitting diodes incorporating the dye molecules as emitting dopants demonstrate electroluminescence in the UV and near-IR ranges.

Copper(II) Etioporphyrinate as a Promising Photoluminescent and Electroluminescent Temperature Sensor.

Luminescent temperature sensors are of great interest because they allow remote determination of temperature in transparent media, such as living tissues, as well as on scattering or transparent surfaces of materials. This study analyzes the luminescent properties of copper(II) etioporphyrinate (Cu-EtioP) in a polystyrene film upon variation of temperature from -195 °C to +65 °C in a cryostat. It is shown that the ratio of intensities of phosphorescence transitions in the red spectral region of such a material varies significantly, that is, the material has thermosensory properties. The phosphorescence decay curves of copper(II) etioporphyrinate in a polystyrene film are analyzed. The quantum yield of phosphorescence of copper(II) etioporphyrinate determined by the absolute method was 3.15%. It was also found that the electroluminescence (EL) spectra of copper(II) etioporphyrinate in a poly(9-vinylcarbazole) (PVK) matrix demonstrated a similar change in the spectra in the temperature range -3 °C to +80 °C. That is, copper(II) etioporphyrinate can also be used as a luminescent temperature sensor as part of an active OLED layer.

Copper(II) meso-Tetraphenyl- and meso-Tetrafluorenyl Porphyrinates as Charge Carrier Transporting and Electroluminescent Compounds.

Studies on copper(II) tetrafluorenyl porphyrinate (CuTFP) and copper(II) tetraphenyl porphyrinate (CuTPP) have been focused on the charge carrier transport in their solid films and electroluminescence of their composites. In the dye layers deposited by resistive thermal evaporation, the mobilities of holes and electrons are on the order of 10-5 and 10-6 cm2 V-1 s-1 for the charge transport under the influence of traps, and the charge mobility reaches the order of 10-3 cm2 V-1 s-1 at space-charge-limited current in the nontrapping mode. For the dye molecules, the correlation between the mobility of charge carriers and the distribution of the electron density on the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO), which serve as hopping sites for holes and electrons, respectively, is considered. Organic light-emitting diodes incorporating the dye molecules as emitting dopants demonstrate electroluminescence in the near-infrared (IR) range.

New Unsymmetrically Substituted Benzothiadiazole-Based Luminophores: Synthesis, Optical, Electrochemical Studies, Charge Transport, and Electroluminescent Characteristics.

Three new benzothiadiazole (BTD)-containing luminophores with different configurations of aryl linkers have been prepared via Pd-catalyzed cross-coupling Suzuki and Buchwald-Hartwig reactions. Photophysical and electroluminescent properties of the compounds were investigated to estimate their potential for optoelectronic applications. All synthesized structures have sufficiently high quantum yields in film. The BTD with aryl bridged carbazole unit demonstrated the highest electrons and holes mobility in a series. OLED with light-emitting layer (EML) based on this compound exhibited the highest brightness, as well as current and luminous efficiency. The synthesized compounds are not only luminophores with a high photoluminescence quantum yield, but also active transport centers for charge carriers in EML of OLED devices.

Effect of Cp-Ligand Methylation on Rhodium(III)-Catalyzed Annulations of Aromatic Carboxylic Acids with Alkynes: Synthesis of Isocoumarins and PAHs for Organic Light-Emitting Devices.

An efficient protocol was developed for the synthesis of π-extended isocoumarins and polycyclic aromatic hydrocarbons based on the oxidative coupling of aromatic carboxylic acids with internal alkynes catalyzed by (cyclopentadienyl)rhodium complexes. The coupling chemoselectivity strongly depends on whether Cp or the methylated Cp* ligands are used. The pentamethyl derivative [Cp*RhCl2 ]2 predominantly gives isocoumarins, while the non-methylated complex [CpRhI2 ]n produces naphthalene derivatives. The polyaromatic carboxylic acids (such as 1-naphthoic acid, 1-pyrenecarboxylic acid, fluorene-1-carboxylic acid, and dibenzofuran-4-carboxylic acid) are suitable for this approach. A mixture of Cp*H/RhCl3 can be used as a catalyst instead of [Cp*RhCl2 ]2 . The structures of 3,4-diphenylindeno[1,2-h]isochromen-1(11H)-one and 7,10-dimethyl-8,9-diphenylbenzo[pqr]tetraphene were determined by X-ray diffraction. In addition, the optical properties of the prepared compounds were studied. 7,8-Diphenyl-10H-phenaleno[1,9-gh]isochromen-10-one was employed as an emissive layer for OLED manufacturing. The OLED emits yellow-green light with a maximum intensity 1740 cd ⋅ m-2 at 15 V.

Slot-Die-Printed Two-Dimensional ZrS3 Charge Transport Layer for Perovskite Light-Emitting Diodes.

Liquid-phase exfoliation of zirconium trisulfide (ZrS3) was used to produce stable and ready-to-use inks for solution-processed semiconductor thin-film deposition. Ribbon-like layered crystals of ZrS3 were produced by the chemical vapor transport method and were then exfoliated in three different solvents: dimethylformamide, ethanol, and isopropyl alcohol. The resulting ZrS3 dispersions were compared for stability and the ability to form continuous films on top of the perovskite layer in light-emitting diodes with the ITO/PEDOT:PSS/MAPbBr3/2D-ZrS3/LiF/Al structure. Film deposition was performed by using either spray or slot-die coating methods. The slot-die coating route proved to produce better and more uniform films with respect to spray coating. We found that the 2D ZrS3 electron injection layer (EIL) stabilized the interface between the perovskite and LiF/Al cathode, reducing the turn-on voltage to 2.8 V and showing a luminance that does not degrade during voltage sweep. On the other hand, EIL-free devices show electroluminescence on the first voltage sweep that reduces almost to zero in the subsequent sweeps. Combining physical device simulation and density functional theory calculation, we are able to explain these results in terms of lowering the electron injection barrier at the cathode.

LMCT facilitated room temperature phosphorescence and energy transfer in substituted thiophenolates of Gd and Yb.

To obtain luminescent lanthanide complexes with a low energy LMCT state the 2-(2'-mercaptophenyl)benzothiazolates, Ln(SSN)3, and 2-(2'-mercaptophenyl)benzoxazolates, Ln2(OSN)6 (Ln = Gd, Yb), were synthesized by the reaction of amides Ln[N(SiMe3)2]3 with respective thiophenols. Ytterbium complexes were structurally characterized by X-ray diffraction analysis. Cyclic voltammetry revealed that the deprotonated mercaptophenyl ligands have significantly lower oxidation potentials than their phenoxy analogues and some ß-diketones. The photophysical properties of Gd and Yb compounds were studied both in solution and in the solid state. The fluorescence spectra of the compounds in solution display the bands of the keto and enol forms of the ligands. No energy transfer from the organic part to Yb3+ has been detected in solutions of both Yb complexes, whereas in solids an intense metal-centered emission in the near infrared region was observed. The solid Gd compounds exhibited room temperature phosphorescence caused by unusually efficient intersystem crossing facilitated by the essentially reducing properties of OSN and SSN ligands. To explain the sensitization process occurring in solids Yb2(OSN)6 and Yb(SSN)3 a specific non-resonant energy transfer mechanism via a ligand to metal charge transfer state has been proposed. Based on the Yb derivatives, NIR-emitting OLEDs with 860 µW cm-2 maximal irradiance were obtained. Their Gd counterparts showed bright electrophosphorescence (up to 1350 cd m-2) in the devices containing doped emission layers.