Measurement of the birefringence variation induced by dihydrogen diffusion into a polarization-maintaining fiber.

We report continuous measurements of the transmission spectrum of a fiber loop mirror interferometer composed of a Panda-type polarization-maintaining (PM) optical fiber during the diffusion of dihydrogen (H2) gas into the fiber. Birefringence variation is measured through the wavelength shift of the interferometer spectrum when the PM fiber is inserted into a gas chamber with H2 concentration from 1.5 to 3.5 vol.% at 75 bar and 70°C. The measurements correlated with simulation results of H2 diffusion into the fiber lead to a birefringence variation of -4.25 × 10-8 per mol m-3 of H2 concentration in the fiber, with a birefringence variation as low as -9.9×10-8 induced by 0.031 µmol m-1 of H2 dissolved in the single-mode silica fiber (for 1.5 vol.%). These results highlight a modification of the strain distribution in the PM fiber, induced by H2 diffusion, leading to a variation of the birefringence that could deteriorate the performances of fiber devices or improve H2 gas sensors.

Gamma-radiation enhancement of sensing properties of FBGs in a few-mode polymer CYTOP fiber.

We investigate the effect of γ-radiation on temperature (T) and relative humidity (RH) sensitivities of polymer perfluorinated fiber Bragg gratings (FBGs). To this aim, different γ-radiation doses (80, 120, 160, and 520 kGy) were applied to a set of FBGs. We show that irradiated FBGs demonstrate an RH sensitivity rise with the received dose: from 13.3 pm/%RH for a pristine FBG up to 56.8 pm/%RH for a 520-kGy dose at 30℃. In contrast, T sensitivity decreases with radiation dose with a subsequent change of sign from positive to negative. Therefore, by experimental interpolation, T sensitivity can be eliminated at around a 160-kGy dose. This opens the possibility of designing an RH sensor with enhanced sensitivity, which at the same time is insensitive to T.

Brillouin Interaction between Two Optical Modes Selectively Excited in Weakly Guiding Multimode Optical Fibers.

A multimode optical fiber supports excitation and propagation of a pure single optical mode, i.e., the field pattern that satisfies the boundary conditions and does not change along the fiber. When two counterpropagating pure optical modes are excited, they could interact through the stimulated Brillouin scattering (SBS) process. Here, we present a simple theoretical formalism describing SBS interaction between two individual optical modes selectively excited in an acoustically isotropic multimode optical fiber. Employing a weakly guiding step-index fiber approach, we have built an analytical expression for the spatial distribution of the sound field amplitude in the fiber core and explored the features of SBS gain spectra, describing the interaction between modes of different orders. In this way, we give a clear insight into the sound propagation effects accompanying SBS in multimode optical fibers, and demonstrate their specific contributions to the SBS gain spectrum.

Properties of Fiber Bragg Grating in CYTOP Fiber Response to Temperature, Humidity, and Strain Using Factorial Design.

The characteristics of fiber Bragg grating (FBG) in cyclic transparent fluoropolymer (CYTOP) optical fiber have attracted more and more attention in recent years. However, different results of the FBG response to environmental parameters are reported. This work presents a three-variable two-level factorial experimental method to investigate the FBG response to temperature, humidity, and strain in CYTOP fiber. Two uniform FBGs are inscribed separately in CYTOP fiber with and without over-clad. With only eight measuring points, the interactions among three variable parameters are computed and the parameter sensitivities and cross-sensitivities are estimated. Similar temperature and strain sensitivities were found for both gratings, whereas significant cross-sensitivity between humidity and temperature was present only in FBG inscribed in CYTOP fiber with over-clad.

Plasma current measurement in ITER with a polarization-OTDR: impact of fiber bending and twisting on the measurement accuracy.

Using a polarization-sensitive optical time domain reflectometer (OTDR), plasma current in the International Thermonuclear Experimental Reactor (ITER) can be measured by investigating the Faraday effect-induced polarization rotation in a spun fiber placed around the Vacuum Vessel. However, intrinsic birefringence and external effects like fiber bending and twisting generate unwanted polarization changes and decrease the measurement accuracy. In this paper, a simulation-based approach is developed, considering bending and twisting effects to assess the performance of the reflectometer in measuring plasma current at ITER. The results demonstrate that, for a proper choice of spun sensing fiber parameters (intrinsic beat length and spun period), the performance of the sensor satisfies ITER accuracy.

Online Gamma Radiation Monitoring Using Few-Mode Polymer CYTOP Fiber Bragg Gratings.

We investigated the gamma radiation response of fiber Bragg gratings (FBGs) inscribed in a few-mode polymer optical fiber. The fiber had a graded-index CYTOP core of 20 µm and XYLEX overclad of 250 µm in diameter. Four FBGs were exposed to gamma radiation during four irradiation sessions at a 5.3 kGy/h dose rate. The FBGs showed a linear Bragg wavelength shift with the received dose with a mean sensitivity of -3.95 pm/kGy at 43 °C. The increased temperature provides a rise in the sensitivity: it reached -10.6 pm/kGy at 58 °C. After irradiation, the FBGs showed partial recovery, which increased with the received dose. Furthermore, the FBG's reflection power decreased with the dose. This attenuation is mainly due to insertion losses caused by the radiation induced attenuation in the CYTOP fiber. Linear response to the received dose makes CYTOP FBGs attractive for gamma radiation dosimetry. However, temperature dependence of the sensitivity should be compensated in practical applications.

Ultra-fast fiber Bragg grating inscription in CYTOP polymer optical fibers using phase mask and 400 nm femtosecond laser.

Fiber Bragg gratings (FBGs) in cyclic transparent fluoropolymer (CYTOP) optical fiber are the subject of a lot of research as they can be of interest for many applications, such as temperature, humidity, strain, and radiation sensing. We report here a new technique to produce high quality FBGs in CYTOP fiber. It uses a femtosecond laser system operating at 400 nm and a phase mask. In contrast to previously reported results, the gratings are obtained in a few seconds with a writing power as low as 80 µW. With this setup, 2 mm-long gratings with reflectivity up to 92 % and full width at half maximum bandwidth around 0.5 nm were obtained in less than 10 s. The resonance wavelengths of the FBGs are confirmed by numerical computation in the graded-index multimode CYTOP fiber, and the mode selection characteristic of FBGs in CYTOP is investigated. Finally, the temperature sensitivity of CYTOP FBG is measured in different mode groups for heating up and cooling down, showing values independent of the mode group measured, but with a small hysteresis.

Effect of Peak Tracking Methods on FBG Calibration Derived by Factorial Design of Experiment.

We present a calibration procedure for a humidity sensor made of a fiber Bragg grating covered by a polyimide layer. FBGs being intrinsically sensitive to temperature and strain, the calibration should tackle three variables, and, therefore, consists of a three-variable, two-level factorial design tailored to assess the three main sensitivities, as well as the five cross-sensitivities. FBG sensing information is encoded in the reflection spectrum from which the Bragg wavelength should be extracted. We tested six classical peak tracking methods on the results of the factorial design of the experiment applied to a homemade FBG humidity sensor. We used Python programming to compute, from the raw spectral data with six typical peak search algorithms, the temperature, strain and humidity sensitivities, as well as the cross-sensitivities, and showed that results are consistent for all algorithms, provided that the points selected to make the computation are correctly chosen. The best results for this particular sensor are obtained with a 3 dB threshold, whatever the peak search method used, and allow to compute the effective humidity sensitivity taking into account the combined effect of temperature and strain. The calibration procedure presented here is nevertheless generic and can thus be adapted to other sensors.

800 nm femtosecond pulses for direct inscription of FBGs in CYTOP polymer optical fiber.

We report the inscription of highly reflective fiber Bragg gratings in perfluorinated polymer (CYTOP) optical fibers using 800 nm femtosecond pulses and a line-by-line inscription method. We demonstrate that the energy for grating inscription without damage is below 27 nJ. After the writing process, we show that the grating reflectivity continues to rise for several hours. The obtained gratings show reflectivity degradation with temperature increase, while the Bragg wavelength undergoes a linear temperature dependence of 37.7 pm/°C when the humidity is controlled and the heating/cooling rate is relatively low (≤0.14∘C/min). The humidity sensitivity at a fixed temperature (25°C) is 22.3 pm/%RH. Finally, the axial strain sensitivity is determined to be 1.35 pm/µÉ›.

Dual-frequency laser comprising a single fiber ring cavity for self-injection locking of DFB laser diode and Brillouin lasing.

Low-noise lasers are a powerful tool in precision spectroscopy, displacement measurements, and development of advanced optical atomic clocks. While all applications benefit from lower frequency noise and robust design, some of them also require lasing at two frequencies. Here, we introduce a simple dual-frequency laser leveraging a ring fiber cavity exploited both for self-injection locking of a standard semiconductor distributed feedback (DFB) laser and for generation of Stokes light via stimulated Brillouin scattering. In contrast to the previous laser configurations, the system is supplied by a low-bandwidth active optoelectronic feedback. Importantly, continuous operation of two mutually locked frequencies is provided by self-injection locking, while the active feedback loop is used just to support this regime. The fiber configuration reduces the natural Lorentzian linewidth of light emitted by the laser at pump and Stokes frequencies down to 270 Hz and 110 Hz, respectively, and features a stable 300-Hz-width RF spectrum recorded with beating of two laser outputs. Translating the proposed laser design to integrated photonics will dramatically reduce cost and footprint for many laser applications such as ultra-high capacity fiber and data center networks, atomic clocks, and microwave photonics.

Stabilizing DFB laser injection-locked to an external fiber-optic ring resonator.

Self-injection locking to an external fiber cavity is an efficient technique enabling drastic linewidth narrowing and self-stabilization of semiconductor lasers. The main drawback of this technique is its high sensitivity to fluctuations of the configuration parameters and surroundings. In the proposed laser configuration, to the best our knowledge, for the first time the self-injection locking mechanism is used in conjunction with a simple active optoelectronic feedback, ensuring stable mode-hopping free laser operation in a single longitudinal mode. Locking to 4-m length fiber resonator causes a drastic narrowing of the DFB laser linewidth down to 2.8 kHz and a reduction of the laser phase noise by three orders of magnitude. We have explored key features of the laser dynamics with and without active feedback, revealing stability and tunability of the laser linewidth as an additional benefit of the proposed technique.

Fiber Bragg grating characterization using factorial design.

The design of the experiment is a scientific approach that provides the maximum amount of information with the minimum number of experiments. It is applicable in scientific and industrial research. We represent a three-variable two-level factorial design to assess fiber Bragg grating properties under simultaneous temperature, humidity, and strain stimuli. Three uniform gratings were inscribed in a single-mode standard optical fiber using the interferometric technique. Two gratings were recoated, one with acrylate and another with a layer of polyimide, while the third grating remained bare. With only eight measuring points, the sensitivities of temperature, strain, and humidity were computed. Moreover, with this technique, the cross-sensitivities between temperature and strain, temperature and humidity, humidity and strain, and between all three factors could also be quantified. We have proven that the results of this design are comparable with those of the classic method. For all gratings, the temperature and strain sensitivities were obtained in the order of 10 pm/°C and 1.1 pm/µÎµ, respectively. The humidity sensitivity of the polyimide recoated grating was estimated to be in the order of 4.47 pm/%RH at room temperature.

Fiber Bragg grating regeneration at 450°C for improved high temperature sensing.

Type-I fiber Bragg gratings photo-inscribed in hydrogen-loaded B/Ge co-doped silica single-mode optical fibers have been regenerated efficiently at 450°C, which is the lowest temperature reported so far. The mechanical strength of the annealed fiber is preserved while ensuring temperature sensing of the regenerated gratings up to 900°C. Unlike low temperature cycles (≤600°C), an annealing process at higher temperatures revealed faster regeneration for strong gratings. Changes in grating strength were also measured before the regeneration cycle. These behaviors suggest the contribution of different mechanisms to the regeneration process with different relative dynamics.

CYTOP Fibre Bragg Grating Sensors for Harsh Radiation Environments.

We present a polymer fibre Bragg grating sensor and its sensitivity to gamma radiation by observing the reflected spectral profile. The Bragg grating is femtosecond inscribed within a perfluorinated CYTOP fibre and the alteration of the Bragg wavelength corresponds to the total radiation dose received. Over a total dose of 41 k Gy, the fibre demonstrates a sensitivity of - 26.2 p m / k Gy and a resolution of 40 Gy. Under active consideration for the instrumentation of nuclear waste repositories, this study gives a better understanding of the effects of gamma radiation upon Bragg gratings in CYTOP fibres.

A novel methodology to assess linear energy transfer and relative biological effectiveness in proton therapy using pairs of differently doped thermoluminescent detectors.

A new methodology for assessing linear energy transfer (LET) and relative biological effectiveness (RBE) in proton therapy beams using thermoluminescent detectors is presented. The method is based on the different LET response of two different lithium fluoride thermoluminescent detectors (LiF:Mg,Ti and LiF:Mg,Cu,P) for measuring charged particles. The relative efficiency of the two detector types was predicted using the recently developed Microdosimetric d(z) Model in combination with the Monte Carlo code PHITS. Afterwards, the calculated ratio of the expected response of the two detector types was correlated with the fluence- and dose- mean values of the unrestricted proton LET. Using the obtained proton dose mean LET as input, the RBE was assessed using a phenomenological biophysical model of cell survival. The aforementioned methodology was benchmarked by exposing the detectors at different depths within the spread out Bragg peak (SOBP) of a clinical proton beam at iThemba LABS. The assessed LET values were found to be in good agreement with the results of radiation transport computer simulations performed using the Monte Carlo code GEANT4. Furthermore, the estimated RBE values were compared with the RBE values experimentally determined by performing colony survival measurements with Chinese Hamster Ovary (CHO) cells during the same experimental run. A very good agreement was found between the results of the proposed methodology and the results of the in vitro study.

MICRODOSIMETRIC MODELING OF THE RELATIVE LUMINESCENCE EFFICIENCY OF LiF:Mg,Cu,P (MCP) DETECTORS EXPOSED TO CHARGED PARTICLES.

Using a recently developed microdosimetric model based on the Monte Carlo code PHITS, the relative luminescence efficiency of LiF:Mg,Cu,P (MCP) thermoluminescent detectors to charged particles from 1H to 132Xe with energies from 3 to 1000 MeV/u has been assessed. The results have been compared with literature data showing very good agreement for particles from 12C to 132Xe in case of model calculations performed in a site size of 40 nm. For 1H and 4He ions, the model overestimates the experimental values by ~10%. An explanation of this deviation as a consequence of fading effects has been included.

Simpplified extended Kalman filter phase noise estimation for CO-OFDM transmissions.

We propose a flexible simplified extended Kalman filter (S-EKF) scheme that can be applied in both pilot-aided and blind modes for phase noise compensation in 16-QAM CO-OFDM transmission systems employing a small-to-moderate number of subcarriers. The performance of the proposed algorithm is evaluated and compared with conventional pilot-aided (PA) and blind phase search (BPS) methods via extensive an Monte Carlo simulation in a back-to-back configuration and with a dual polarization fiber transmission. For 64 subcarrier 32 Gbaud 16-QAM CO-OFDM systems with 200 kHz combined laser linewidths, an optical signal-to-noise ratio penalty as low as 1 dB can be achieved with the proposed S-EKF scheme using only 2 pilots in the pilot-aided mode and just 4 inputs in the blind mode, resulting in a spectrally efficient enhancement by a factor of 3 and a computational effort reduction by a factor of more than 50 in comparison with the conventional PA and the BPS methods, respectively.

Nondestructive distributed measurement of supercontinuum generation along highly nonlinear optical fibers.

Supercontinuum generation (SCG) in optical fibers arises from the spectral broadening of an intense light, which results from the interplay of both linear and nonlinear optical effects. In this Letter, a nondestructive optical time domain reflectometry method is proposed for the first time, to the best of our knowledge, to measure the spatial (longitudinal) evolution of the SC induced along an optical fiber. The method was experimentally tested on highly nonlinear fibers. The experimental results are in a good agreement with the optical spectra measured at the fiber outputs.

Fiber-Optic Surface Temperature Sensor Based on Modal Interference.

Spatially-integrated surface temperature sensing is highly useful when it comes to controlling processes, detecting hazardous conditions or monitoring the health and safety of equipment and people. Fiber-optic sensing based on modal interference has shown great sensitivity to temperature variation, by means of cost-effective image-processing of few-mode interference patterns. New developments in the field of sensor configuration, as described in this paper, include an innovative cooling and heating phase discrimination functionality and more precise measurements, based entirely on the image processing of interference patterns. The proposed technique was applied to the measurement of the integrated surface temperature of a hollow cylinder and compared with a conventional measurement system, consisting of an infrared camera and precision temperature probe. As a result, the optical technique is in line with the reference system. Compared with conventional surface temperature probes, the optical technique has the following advantages: low heat capacity temperature measurement errors, easier spatial deployment, and replacement of multiple angle infrared camera shooting and the continuous monitoring of surfaces that are not visually accessible.

Control over photo-inscription and thermal annealing to obtain high-quality Bragg gratings in doped PMMA optical fibers.

Bragg gratings are photo-inscribed in trans-4-stilbenemethanol doped PMMA fibers using a 325 nm He-Cd laser and a phase mask. Two distinct behaviors are reported depending on the laser power density. In the high-density regime with 637 mW/mm2, the grating reflectivity is stable over time after the writing process, but the reflected spectrum is of limited quality, as the grating length is limited to the laser width (1.2 mm). The beam is then enlarged to 6 mm, decreasing the power density to 127 mW/mm2. In this case, the grating reflectivity strongly decays after the writing process. A fortunate property here results from the recovery of the initial reflectivity using a post-inscription thermal annealing. Both behaviors are attributed to the evolution between trans- and cis-isomers.