Replicating endothelial shear stress in organ-on-a-chip for predictive hypericin photodynamic efficiency.

Photodynamic therapy using Hypericin (Hy-PDT) is an alternative non-invasive treatment that enables selective tumor inhibition and angiogenesis derived from the differential recruitment of endothelial cells in the tumor microenvironment. Most PDT studies were performed on in vitro models without vascular biomechanical simulation. Our work strives to develop a microchip that generates a constant shear stress force to investigate the Hy-PDT efficiency on human umbilical vein endothelial cells (HUVECs). The microchip with a single straight microchannel was composed of the bottom layer (polystyrene), the middle layer (double-sided biocompatible adhesive tape), and the top layer (polyester film) and could produce shear stress in the range of 1.4 - 7.0 dyn cm-2. The quantification of vascular endothelial growth factor (VEGF), cell viability, and activities of caspases 3 and 7 were assayed to validate the microchip and Hy-PDT efficacy. After the endothelization, static and dynamic cell incubations with Hy were conducted in microchips. Compared to static systems, the shear stress displayed its effect on the increasing release of VEGF and promoted more cell damage and cell death via necrosis during Hy-PDT. In conclusion, the expressive shear stress-dependent manner during PDT treatments suggests that the microchip could be an essential approach in preclinical tests to evaluate the therapeutic outcome considering the endothelial shear stress microenvironment.

Hypericin-loaded oil-in-water nanoemulsion synthesized by ultrasonication process enhances photodynamic therapy efficiency.

Hypericin (Hy) is a hydrophobic photosensitizer used in photodynamic therapy for cancer therapeutic. In this study, Hy-loaded oil-in-water (O/W) nanoemulsions (NEs) were produced by the ultrasonication method combing different biocompatible oils and surfactants to enhance Hy aqueous solubility and bioavailability. Experimental parameters were optimized by the characterization of droplet size, zeta potential, and physicochemical properties. In vitro studies based on the release profile, cytotoxicity, cell morphology, and Hy intracellular accumulation were assayed. Hy at 100 mg L-1 was incorporated into the low viscosity (~0.005 Pa s) NEs with spherical droplets averaging 20-40 nm in size and polydispersity index <0.02. Hy release from the NE was significantly higher (4-fold) than its suspension (p < 0.001). The NEs demonstrated good physical stability during storage at 5 °C for at least six months. The Hy-loaded NEs exhibited an IC50 value 6-fold lower than Hy suspension during PDT against breast cancer cell lines (MCF-7). Cell microscopy imaging confirmed the increased cytotoxic effects of Hy-loaded NEs, showing damaged and apoptotic cells. Confocal laser scanning microscopy evidenced greater Hy delivery through NE into MCF-7 cells followed by improved intracellular ROS generation. Our results suggest that the Hy-loaded NEs can improve hypericin efficacy and assist Hy-PDT's preclinical development as a cancer treatment.

Rapid Fabrication of Microfluidic Devices for Biological Mimicking: A Survey of Materials and Biocompatibility.

Microfluidics is an essential technique used in the development of in vitro models for mimicking complex biological systems. The microchip with microfluidic flows offers the precise control of the microenvironment where the cells can grow and structure inside channels to resemble in vivo conditions allowing a proper cellular response investigation. Hence, this study aimed to develop low-cost, simple microchips to simulate the shear stress effect on the human umbilical vein endothelial cells (HUVEC). Differentially from other biological microfluidic devices described in the literature, we used readily available tools like heat-lamination, toner printer, laser cutter and biocompatible double-sided adhesive tapes to bind different layers of materials together, forming a designed composite with a microchannel. In addition, we screened alternative substrates, including polyester-toner, polyester-vinyl, glass, Permanox® and polystyrene to compose the microchips for optimizing cell adhesion, then enabling these microdevices when coupled to a syringe pump, the cells can withstand the fluid shear stress range from 1 to 4 dyne cm2. The cell viability was monitored by acridine orange/ethidium bromide (AO/EB) staining to detect live and dead cells. As a result, our fabrication processes were cost-effective and straightforward. The materials investigated in the assembling of the microchips exhibited good cell viability and biocompatibility, providing a dynamic microenvironment for cell proliferation. Therefore, we suggest that these microchips could be available everywhere, allowing in vitro assays for daily laboratory experiments and further developing the organ-on-a-chip concept.

One-Pot Hydrothermal Preparation of Fe3O4 Decorated Graphene for Microwave Absorption.

Fe3O4 decorated graphene was synthesized for electromagnetic wave absorption via a facile one-pot hydrothermal approach. The structure and morphology of the as-prepared nanomaterials were systematically investigated. The graphene oxide (GO) was reduced and Fe3O4 nanoparticles were evenly decorated on the surface of reduced graphene oxide (rGO) nanosheets. The average particle size of Fe3O4 nanoparticles is about 15.3 nm. The as-prepared rGO-Fe3O4 nanocomposites exhibited a good microwave absorption performance because of the combination of graphene and magnetic Fe3O4. When the thicknesses are 1.6 mm and 6.5 mm, the reflection loss (RL) values are up to -34.4 dB and -37.5 dB, respectively. The effective bandwidths are 3.8 and 1.9 GHz.

Hydrophilic and Antibacterial Modification of Poly(lactic acid) Films by γ-ray Irradiation.

To improve the hydrophilicity and imparting antibacterial properties to poly(lactic acid), poly(acrylic acid) (PAA) and silver particles (AgNPs) were simultaneously introduced onto the surface of poly(lactic acid) (PLA) films by γ-ray irradiation. The morphology and structure of the modified films were characterized by scanning electron microscopy (SEM)/energy-dispersive X-ray (EDX) spectrometry and Fourier transform infrared (FTIR) spectroscopy. The interaction between PAA and AgNPs was investigated by X-ray photoelectron spectroscopy (XPS), confirming the coordination between AgNPs and the oxygen atom on the carboxylic group of PAA. The contact-angle (CA) measurements and antibacterial tests showed that the modified PLA films with a low silver content (PLA-g-PAA-Ag) exhibited excellent hydrophilicity as well as antibacterial activity compared with the neat PLA film.

Gamma Irradiation-Induced Preparation of Graphene⁻Ni Nanocomposites with Efficient Electromagnetic Wave Absorption.

A facile and environmentally friendly method is proposed to prepare reduced graphene oxide⁻nickel (RGO⁻Ni) nanocomposites using γ-ray irradiation. Graphene oxide (GO) and Ni2+ are reduced by the electrons which originated from the gamma radiolysis of H2O. The structure and morphology of the obtained RGO⁻Ni nanocomposites were analyzed using X-ray diffraction (XRD) and Raman spectroscopy. The results show that Ni nanoparticles were dispersed uniformly on the surface of the RGO nanosheets. As expected, the combination of RGO nanosheets and Ni nanoparticles improved the electromagnetic wave absorption because of the better impedance matching. RGO⁻Ni nanocomposites exhibited efficient electromagnetic wave absorption performance. The minimum reflection loss (RL) of RGO⁻Ni reached -24.8 dB, and the highest effective absorption bandwidth was up to 6.9 GHz (RL < -10 dB) with a layer thickness of 9 mm.

Transcript Profiling and Gene Identification Involved in the Ethylene Signal Transduction Pathways of Creeping Bentgrass (Agrostis stolonifera) during ISR Response Induced by Butanediol.

Creeping bentgrass (Agrostis stolonifera) is the preferred green lawn grass, with excellent turf characteristics but poor disease resistance. At present, the mechanisms of disease resistance in creeping bentgrass are poorly understood, especially the ethylene signal transduction pathway under the induced systemic resistance (ISR) response. In this study, butanediol (BDO), as a new type of disease-resistance compound, was applied to creeping bentgrass seedlings to induce the ISR response. Then, we measured ethylene production and related enzyme activities. Additionally, transcript profiling and gene identification were performed in association to ethylene signal transduction pathways. The changes of ethylene production and related enzyme 1-aminocyclopropane-1-carboxylic acid oxidase (ACO) and 1-aminocyclopropane-1-carboxylic acid synthases (ACS) activities showed significant difference at 24 h after Rhizoctonia solani inoculation among five treatments of various BDO concentrations. After 100 µmol L-1 BDO treatment, ethylene production and related enzyme activities reached their peak levels. Additionally, 208,672 unigenes of creeping bentgrass were obtained by de novo assembly. In total, 15,903 annotated unigenes were grouped into 33 canonical pathways in the KEGG (Kyoto Encyclopedia of Genes and Genomes) analysis. Among those, 1803 unigenes were classified as 'signal transduction'. There were 6766 differentially expressed genes (DEGs) among B24 (inoculated-rhizobacteria in MS medium with 100 µmol L-1 BDO for 24 h), NB24, B72 and NB24 (no rhizobacteria in MS medium with 100 µmol L-1 BDO for 24 h) libraries, and 4,639 DEGs between B24 and B72 (inoculated-rhizobacteria in MS medium with 100 µmol L-1 BDO for 72 h) libraries, with 4489 DEGs in all three libraries. As suggested by the RT-PCR assay, the expression levels of ethylene-responsive and defense-related genes were variable among treated samples during the BDO-induced ISR responses. The expression levels of EIN, ERF, NPR1, PR3 and PR4 genes increased and reached their peaks in the first 24 h after R. solani infection in the BDO-induced ISR reaction compared with NB24 treatments. This results is consistent with the changes of important ethylene biosynthetic enzymes and ethylene concentrations during the BDO-induced ISR responses. We further found the intermediate substances for the signaling pathway, and the relationships between the expression levels of BDO-induced ISR disease-resistance genes and those of the response genes for ethylene signal pathway. Our findings present a genetic basis for systemic resistance of creeping bentgrass through transcriptomic analysis and our study provides a theoretical and practical basis for the improvement of turfgrass disease resistance and quality.

Structure Mediation and Properties of Poly(l-lactide)/Poly(d-lactide) Blend Fibers.

Poly(l-lactic acid) (PLLA) and poly(d-lactic acid) (PDLA) blend as-spun fibers (50/50, wt.%) were prepared by melt spinning. Structure mediation under temperature and stress and properties of poly(l-lactic acid)/poly(d-lactic acid)(PLLA/PDLA) as-spun fibers were investigated by wide-angle X-ray scattering (WAXS) and differential scanning calorimetry (DSC). The results show that highly oriented stereocomplex (SC) crystals can be formed in PLLA/PDLA blend fibers drawn at 60 °C and annealed at 200 °C. However, at drawn temperature of 80 °C, only lower oriented SC crystals can be formed. For PLLA/PDLA blend fibers drawn twice at 60 °C (PLLA/PDLA-60-2), the crystallinity of SC crystals increases with annealing temperature in the range of 200 to 215 °C, while the degree of orientation decreases slightly. When the annealing temperature is 210 °C, the crystallinity and orientation of SC crystals in PLLA/PDLA-60-2 fibers reach 51% and -0.39, respectively. Moreover, PLLA/PDLA-60-2-210 fibers exhibit excellent heat-resistant property even at 200 °C. The results indicate that the oriented PLLA/PDLA blend fibers with high SC crystals content can be regulated in a short time.

Oxidized multiwall carbon nanotube/silicone foam composites with effective electromagnetic interference shielding and high gamma radiation stability.

Oxidized multiwall carbon nanotubes (o-MWCNTs) were introduced into silicone foam to fabricate an electromagnetic interference (EMI) shielding material with high gamma radiation stability by solution casting followed by foaming and cross-linking reactions. The as-prepared o-MWCNT/silicone foam composites exhibited excellent mechanical strength and effective EMI shielding properties with superior EMI shielding effectiveness (SE) ranging from 26 to 73 dB at a 0.5-6.4 mm thickness with 30 wt% o-MWCNTs in the Ku band. Moreover, the composites have good gamma radiation stability, showing relatively stable EMI shielding properties and an improvement of hardness and pressure resistance after gamma irradiation with the absorbed dose of 500 kGy. These results indicate that the o-MWCNT/silicone foam composite is an attractive candidate for EMI shielding in some ionizing radiation environments.

Facile synthesis of a novel polymeric ionic liquid gel and its excellent performance for hexavalent chromium removal.

A novel polymeric ionic liquid gel (PIL gel) was simply synthesized by γ-radiation-induced polymerization of ionic liquid monomer 1-allyl-3-vinylimidazolium chloride and crosslinking at ambient temperature without any additives. By changing the radiation dose, the properties of the resulting gel including the gel fraction, crosslinking density and equilibrium degree of swelling were optimized. The resulting PIL gel exhibited a superior adsorption ability toward Cr(vi) in aqueous solutions with a broad pH range (1-7) through anion exchange. It was found that the adsorption kinetics followed the pseudo-second-order model. The adsorption of Cr(vi) by the PIL gel obeyed the Langmuir isotherm equation with a theoretical maximum adsorption capacity of 283 mg g(-1), twice the highest value for ionic liquid-based adsorbents that have been reported. In addition, the PIL gel could be recovered using a NaCl solution or a NaOH solution without much decreasing the adsorption capacity. This work paves the way for the scale-up production of PIL gels using the radiation technique for potential application in heavy metal removal.

Functionalization and reduction of graphene oxide with p-phenylene diamine for electrically conductive and thermally stable polystyrene composites.

A facile and efficient approach was developed to simultaneously functionalize and reduce graphene oxide (GO) with p-phenylene diamine (PPD) by simple refluxing. This was possible by the nucleophilic substitution reaction of epoxide groups of GO with amine groups of PPD aided by NH(3) solution. As a consequence, electrical conductivity of GO-PPD increased to 2.1 × 10(2) S/m, which was nearly 9 orders of magnitude higher than that of GO. Additionally, after the incorporation of GO-PPD in polystyrene (PS), the composites exhibited a sharp transition from electrically insulating to conducting behavior with a low percolation threshold of ~0.34 vol %, which was attributed to the improved dispersion and the reduction of GO-PPD. Thermal stability of the PS/GO-PPD composite was also ~8 °C higher than that of PS.