Effect of Dope Flow Rate and Post-Treatment on the Morphology, Permeation and Metal Ion Rejection from PES/LiBr-Based UF Hollow Fiber Membranes.

This study investigated the influence of dope extrusion rate (DER) and post-treatment effect on the morphology, permeation, and metal ion rejection by polyethersulfone/lithium bromide (PES/LiBr)-based hollow fiber (HF) membranes. HF fibers were spun with 2.25, 2.5, and 3.1 ratios of DER to bore fluid rate (BFR), wherein DER varied from 11.35, 12.5, to 15.6 mL/min with a fixed BFR (5 mL/min). Molecular weight cutoff (MWCO), pore size, water flux, and flux recovery ratio were determined, whereas lake water was used to observe the rejection rate of dissolved metallic ions. Results showed that with the increase of the DER wall thickness (WT), HFs increased from 401.5 to 419.5 um, and furthermore by the post-treatments up to 548.2 um, as confirmed by field emission scanning electron microscope (FESEM) analysis. Moreover, MWCO, pore size, and the pure water permeation (PWP) of the HF membranes decreased, while the separation performance for polyethylene glycol (PEG) solute increased with increasing DER. Post-treated HFs from 11.35 mL/min of DER showed 93.8% of MWCO value with up to 90% and 70% rejection of the arsenic and chromium metallic ions, respectively, in comparison with all other formulated HFs.

Dual Optimized Sulfonated Polyethersulfone and Functionalized Multiwall Carbon Tube Based Composites High Fouling Resistance Membrane for Protein Separation.

Commercial grade sulfonated-Polyethersulfone (S-PES) and functionalized multiwall carbon nanotube (f-MWCNT)/polyvinylpyrrolidone (PVP) nanocomposites (NCs) were used to enhance and optimize the antifouling, protein resistance and protein separation properties of the S-PES ultrafiltration membranes. The polarities of sulfonic groups of S-PES, carbonyl carbon of pyrrolidone, hydroxyl and carboxyl groups of f-MWCNT in the membrane composition helped to strongly bind each other through hydrogen bonding, as shown by Fourier-transform infrared spectroscopy (FTIR). These binding forces greatly reduced the leaching of NCs and developed long finger-like projection, as confirmed by elution ratio and cross-sectional studies of the membranes via field emission scanning electron microscope (FESEM). The contact angle was reduced up to 48% more than pristine PES. Atomic force microscopy (AFM) was employed to study the various parameters of surface roughness with 3d diagrams, while grain analysis of membrane surface provided a quantitative estimation about volume, area, perimeter, length, radius and diameter. The NCs/S-PES enhanced the flux rate with an impressive (80-84%) flux recovery ratio and (58-62%) reversible resistance (Rr) value in situ, with 60% and 54.4% lesser dynamic and static protein adsorption. The best performing membrane were reported to remove 31.8%, 66.3%, 83.6% and 99.9% for lysozyme-(14.6 kDa), trypsin-(20 kDa), pepsin-(34.6 kDa) and bovine serum albumin (BSA-66 kDa), respectively.

Ruthenium-Doping-Induced Amorphization of VS4 Nanostructures with a Rich Sulfur Vacancy for Enhanced Hydrogen Evolution Reaction in a Neutral Electrolyte Medium.

The generation of pure H2 from a neutral electrolyte solution represents a transformative route with low cost and environmentally friendly nature. However, the complex kinetics of hydrogen evolution reaction (HER) via water electrolysis make its practical application to be difficult. Herein, we have reported Ru-doping-induced formation of VS4 nanostructures with a rich S vacancy for neutral HER in a 0.2 M phosphate buffer solution. The Ru-doped VS4 demands an overpotential value of 160 mV at 10 mA/cm2 current density with a lower catalyst loading of 0.1 mg/cm2, while pristine VS4 demands a 374 mV overpotential with the same mass loading. 60 hours of chronoamperometric study reveals the excellent stability of Ru-doped VS4 materials, which is the highest amount of time ever reported for neutral HER. The marginal degradation of a catalyst under a long-term stability study was confirmed through inductively coupled plasma mass spectrometry (ICP-MS) analysis. The introduction of Ru to the VS4 lattice leads to a 4.35-fold increase in the turnover-frequency values compared to those of bare VS4 nanostructures. The higher HER activity of S-vacancy-enriched VS4 materials is thought to originate through effective water adsorption in S vacancy and Ru3+ sites followed by the dissociation of a H2O molecule, and S22- efficiently converts Had to H2. Also, post-HER characterization reveals that the transformation of some Ru3+ to Ru0 additionally favored the HER by providing a better H adsorption site under a static cathodic potential.

Boiling Heat Transfer Evaluation in Nanoporous Surface Coatings.

The present study develops a deep learning method for predicting the boiling heat transfer coefficient (HTC) of nanoporous coated surfaces. Nanoporous coated surfaces have been used extensively over the years to improve the performance of the boiling process. Despite the large amount of experimental data on pool boiling of coated nanoporous surfaces, precise mathematical-empirical approaches have not been developed to estimate the HTC. The proposed method is able to cope with the complex nature of the boiling of nanoporous surfaces with different working fluids with completely different thermophysical properties. The proposed deep learning method is applicable to a wide variety of substrates and coating materials manufactured by various manufacturing processes. The analysis of the correlation matrix confirms that the pore diameter, the thermal conductivity of the substrate, the heat flow, and the thermophysical properties of the working fluids are the most important independent variable parameters estimation under consideration. Several deep neural networks are designed and evaluated to find the optimized model with respect to its prediction accuracy using experimental data (1042 points). The best model could assess the HTC with an R2 = 0.998 and (mean absolute error) MAE% = 1.94.

The Role of Sintering Temperature and Dual Metal Substitutions (Al3+, Ti4+) in the Development of NASICON-Structured Electrolyte.

The aim of this study is to synthesize Li1+xAlxTixSn2-2x(PO4) sodium super ion conductor (NASICON) -based ceramic solid electrolyte and to study the effect of dual metal substitution on the electrical and structural properties of the electrolyte. The performance of the electrolyte is analyzed based on the sintering temperature (550 to 950 °C) as well as the composition. The trend of XRD results reveals the presence of impurities in the sample, and from Rietveld Refinement, the purest sample is achieved at a sintering temperature of 950 °C and when x = 0.6. The electrolytes obey Vegard's Law as the addition of Al3+ and Ti4+ provide linear relation with cell volume, which signifies a random distribution. The different composition has a different optimum sintering temperature at which the highest conductivity is achieved when the sample is sintered at 650 °C and x = 0.4. Field emission scanning electron microscope (FESEM) analysis showed that higher sintering temperature promotes the increment of grain boundaries and size. Based on energy dispersive X-ray spectroscopy (EDX) analysis, x = 0.4 produced the closest atomic percentage ratio to the theoretical value. Electrode polarization is found to be at maximum when x = 0.4, which is determined from dielectric analysis. The electrolytes follow non-Debye behavior as it shows a variety of relaxation times.

Characteristics of Plasticized Lithium Ion Conducting Green Polymer Blend Electrolytes Based on CS: Dextran with High Energy Density and Specific Capacitance.

The solution cast process is used to set up chitosan: dextran-based plasticized solid polymer electrolyte with high specific capacitance (228.62 F/g) at the 1st cycle. Fourier-transform infrared spectroscopy (FTIR) pattern revealed the interaction between polymers and electrolyte components. At ambient temperature, the highest conductive plasticized system (CDLG-3) achieves a maximum conductivity of 4.16 × 10-4 S cm-1. Using both FTIR and electrical impedance spectroscopy (EIS) methods, the mobility, number density, and diffusion coefficient of ions are measured, and they are found to rise as the amount of glycerol increases. Ions are the primary charge carriers, according to transference number measurement (TNM). According to linear sweep voltammetry (LSV), the CDLG-3 system's electrochemical stability window is 2.2 V. In the preparation of electrical double layer capacitor devices, the CDLG-3 system was used. There are no Faradaic peaks on the cyclic voltammetry (CV) curve, which is virtually rectangular. Beyond the 20th cycle, the power density, energy density, and specific capacitance values from the galvanostatic charge-discharge are practically constant at 480 W/Kg, 8 Wh/Kg, and 60 F g-1, for 180 cycles.

Characteristics of PEO Incorporated with CaTiO3 Nanoparticles: Structural and Optical Properties.

In this research, direct band gap polymer composites with amorphous phase, which are imperative for optoelectronic devices applications were synthesized. The solution cast technique was used to produce polyethylene oxide (PEO)/calcium titanate (CaTiO3) nanocomposite (NC) films. The X-ray diffraction (XRD) confirms the growth of amorphous nature within PEO with CaTiO3 addition. The optical band gaps of pure PEO and PEO/CaTiO3 NC films were calculated using analysis of ultraviolet-visible (UV-Vis) spectra. The change in absorption edge toward lower photon energy is evidence of polymer modification. The dispersion behavior of the refractive index of PEO was manipulated to a higher wavelength upon doping with CaTiO3. Upon adding CaTiO3 to the pure PEO polymer, the dielectric constant and refractive index were considerably modified. The band gap shifts from 4.90 eV to 4.19 eV for the PEO incorporated with an optimum portion of 8 wt. % of CaTiO3. The types of the electronic transition in composite samples were specified, based on the Taucs model and the optical dielectric loss. The alteration of UV/Vis absorption spectra of the NC film was considered a suitable candidate to be applied in nanotechnology-based devices. The spherulites ascribed to the crystalline phase were distinguished through the optical microscopy (OM) study.

Preparation and Characterization of a Novel Activated Carbon@Polyindole Composite for the Effective Removal of Ionic Dye from Water.

The present study is aimed at the synthesis and exploring the efficiency of a novel activated carbon incorporated polyindole (AC@PIN) composite for adsorptive removal of Malachite Green (MG) dye from aqueous solution. An AC@PIN hybrid material was prepared by in situ chemical oxidative polymerization. The physico-chemical characteristics of the AC@PIN composite were assessed using Fourier-transform infrared spectrometer, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, ultraviolet visible spectroscopy, and determination of point of zero charge (pHPZC). A series of adsorption studies was conducted to evaluate the influence of operational parameters such as pH, contact time, initial dye concentration, AC@PIN dosage, and temperature on dye adsorption behavior of developed composite. A maximum dye removal percentage (97.3%) was achieved at the pH = 10, AC@PIN dosage = 6.0 mg, initial dye concentration 150 mg L-1, and temperature = 20 °C. The kinetic studies demonstrated that the adsorption of MG on AC@PIN followed pseudo-second-order model (R2 ≥ 0.99). Meanwhile, Langmuir isotherm model was founded to be the best isotherm model to describe the adsorption process. Finally, the recyclability test revealed that the composite exhibits good recycle efficiency and is stable after 5 cycles. The obtained results suggest that AC@PIN composite could be a potential candidate for the removal of MG from wastewater.

Interleukin-4 and interferon-γ are possible allergic markers in pediatric patients with ß-lactam hypersensitivity.

BACKGROUND: ß-lactam agents are known to elicit T-cell-mediated immune responses that play a central role in the onset of allergic reactions, but the involvement of specific type of cytokines in drug allergy remains largely unexplored in humans. OBJECTIVES: This study was undertaken to investigate the role of cytokines involvement in pediatric patients with ß-lactam hypersensitivity and to determine whether involvement of cytokines in drug-mediated reactions are important for the perspective of allergic patient's management. METHODS: ß-lactam-induced hypersensitivity reactions in eighty pediatric patients were determined by clinical manifestations and skin prick or intradermal testing. Production of T-helper (Th) type-1 cytokine interferon (INF)-γ, Th-2 cytokine interleukin (IL)-4, regulatory T-cell cytokine IL-10, and other cytokines IL-6 and IL-12 were determined by sandwich ELISAs. RESULTS: Diagnosis of ß-lactam allergy was confirmed in 53 pediatric patients. IL-4 secretion in patients' sera was significantly higher as compared with healthy controls (P < 0.05). However, INF-γ level in patients' sera was significantly lower as compared with controls (P < 0.05). No significant alterations were found in the protein secretion of IL-10, IL-12, and IL-6 in allergic patients as compared with controls (P > 0.05). CONCLUSION: We conclude that IL-4 is specific marker for the diagnosis of ß-lactam-induced hypersensitivity. Moreover, IL-4 in combination with INF-γ is more sensitive for the diagnosis of these reactions. This study also concludes that both IL-4 and INF-γ may play an active role in the onset of allergic reactions against ß-lactam antibiotics.

Dielectric characterization and catalytic activity studies of nickel chloride doped carboxymethyl cellulose films.

Cast technique was used to prepare films of sodium carboxymethyl cellulose (CMC) doped with different ratios of NiCl(2)·6H(2)O in the range of 0-40Ni(2+) wt.%. Thermal analysis (DTA) in the range of 25-600°C and dielectric properties in the temperature range of 30-150°C and frequency range of 0.1-100 kHz were measured for the prepared samples. DTA analysis showed new exothermic peaks which were attributed to structural phase transitions. Different molecular motions are separated via dielectric relaxation spectroscopy. In the high temperature range (higher than 100°C), the σ-relaxation, which is associated with the hopping motion of ions through polymer material, was detected. The detailed analysis of the results showed that the dielectric dispersion consists of both dipolar and interfacial polarization. Measurements of ac conductivity as a function of frequency at different temperatures indicated that the correlated barrier hopping model (CBH) is the most suitable mechanism for the ac conduction behavior. The catalytic activity of CMC doped with Ni(2+) was tested in the reduction of the hazardous pollutant 4-nitrophenol to the functional 4-aminophenol with an excess amount of NaBH(4). Ni-free CMC did not exhibit any catalytic activity for the studied reaction. However, Ni(2+)-doped CMC showed a significant catalytic activity that is proportional to the ratio of Ni(2+) included in CMC. The activation energy (E(a)) was estimated in the temperature range of 25-40°C. The estimated value of E(a) decreased with increasing the ratio of Ni(2+). Finally, the optimum catalyst mass was found to be ≈0.6 g/l.