Breed and loading history influence in vivo skeletal strain patterns in pre-pubertal female chickens.

The influence of loading history on in vivo strains within a given specie remains poorly understood, and although in vivo strains have been measured at the hindlimb bones of various species, strains engendered during modes of activity other than locomotion are lacking, particularly in non-human species. For commercial egg-laying chickens specifically, there is an interest in understanding their bones' mechanical behaviour, particularly during youth, to develop early interventions to prevent the high incidence of osteoporosis in this population. We measured in vivo mechanical strains at the tibiotarsus midshaft during steady activities (ground, uphill, downhill locomotion) and non-steady activities (perching, jumping, aerial transition landing) in 48 pre-pubescent female (egg-laying) chickens from two breeds that were reared in three different housing systems, allowing varying amounts and types of physical activity. Mechanical strain patterns differed between breeds, and were dependent on the activity performed. Mechanical strains were also affected by rearing environment: chickens that were restricted from performing dynamic load bearing activity due to caged-housing generally exhibited higher mechanical strain levels during steady, but not non-steady activities, compared to chickens with prior dynamic load-bearing activity experience. Among chickens with prior experience of dynamic load bearing activity, those reared in housing systems that allowed more frequent physical activity did not exhibit lower mechanical strains. In all groups, the tibiotarsus was subjected to a loading environment consisting of a combination of axial compression, bending, and torsion, with torsion being the predominant source of strain. Aerial transition landing produced the highest strain levels with unusual strain patterns compared to other activities, suggesting it may produce the strongest anabolic response. These results exemplify how different breeds within a given specie adapt to maintain different patterns of mechanical strains, and how benefits of physical activity in terms of resistance to strain are activity-type dependent and do not necessarily increase with increased physical activity. These findings directly inform controlled loading experiments aimed at studying the bone mechanoresponse in young female chickens and can also be associated to measures of bone morphology and material properties to understand how these features influence bone mechanical properties in vivo.

Osteocyte Estrogen Receptor ß (Ot-ERß) Regulates Bone Turnover and Skeletal Adaptive Response to Mechanical Loading Differently in Male and Female Growing and Adult Mice.

Age-related bone loss is a failure of balanced bone turnover and diminished skeletal mechanoadaptation. Estrogen receptors, ERα and ERß, play critical roles in osteoprotective regulation activated by estrogen and mechanical signals. Previous studies mainly focused on ERα and showed that osteocyte-ERα (Ot-ERα) regulated trabecular, but not cortical bone, and played a minor role in load-induced cortical adaptation. However, the role of Ot-ERß in bone mass regulation remains unrevealed. To address this issue, we characterized bone (re)modeling and gene expression in male and female mice with Ot-ERß deletion (ERß-dOT) and littermate control (LC) at 10 weeks (young) or 28 weeks (adult) of age, as well as their responses to in vivo tibial compressive loading. Increased cancellous bone mass appeared in the L4 vertebral body of young male ERß-dOT mice. At the same time, femoral cortical bone gene expression showed signs consistent with elevated osteoblast and osteoclast activities (type-I collagen, Cat K, RANKL). Upregulated androgen receptor (AR) expression was observed in young male ERß-dOT mice relative to LC, suggesting a compensatory effect of testosterone on male bone protection. In contrast, bone mass in L4 decreased in adult male ERß-dOT mice, attributed to potentially increased bone resorption activity (Cat K) with no change in bone formation. There was no effect of ERß-dOT on bone mass or gene expression in female mice. Sex-dependent regulation of Ot-ERß also appeared in load-induced cortical responsiveness. Young female ERß-dOT mice showed an enhanced tibial cortical anabolic adaptation compared with LC. In contrast, an attenuated cortical anabolic response presented at the proximal tibia in male ERß-dOT mice at both ages. For the first time, our findings suggest that Ot-ERß regulates bone (re)modeling and the response to mechanical signals through different mechanisms in males and females. © 2022 The Authors. Journal of Bone and Mineral Research published by Wiley Periodicals LLC on behalf of American Society for Bone and Mineral Research (ASBMR).

Computational modeling for osteogenic potential assessment of physical exercises based on loading-induced mechanobiological environments in cortical bone remodeling.

Osteoporosis and disuse can cause bone loss which reduces the weight-bearing strength of long bones. Physical exercise or mechanical loading prevents bone loss as it promotes bone modeling through osteogenesis, i.e., new bone formation. Several studies have observed distinct bone remodeling responses to physical exercises; nevertheless, the underlying mechanism behind such responses is not well established. Loading-induced pore-pressure and fluid motion act as mechanobiological stimuli to bone cells namely osteocytes which further initiate osteoactivities. The shape of loading waveforms also affects the poromechanical environment of bone. Accordingly, the present study hypothesizes that loading waveforms associated with physiological exercises may expose the bone to different mechanobiological stimuli resulting in distinct bone remodeling. A poromechanical finite element model is developed to compute pore-pressure and interstitial fluid velocity in femoral cortical bone tissue (healthy and osteoporotic) subjected to loading waveforms of three physiological exercises namely walking, running, and jumping. The model also computes the mechanobiological stimulus as a function of fluid velocity. The outcomes indicate that pore-pressure and fluid velocity decrease significantly in osteoporotic bone tissue in comparison with healthy tissue. Jumping and running both improve pore-pressure and fluid velocity in healthy and osteoporotic tissues, whereas running significantly enhances mechanobiological stimulus in both the tissues which indicates a possible explanation for distinct bone remodeling to different physical exercises. The present work also suggests that running may be recommended as a potential biomechanical therapeutic to prevent bone loss. Overall, the present work contributes to the area of orthopedic research to develop effective designs of prophylactic exercises to improve bone health.

Effects of Dietary Protein Source and Quantity on Bone Morphology and Body Composition Following a High-Protein Weight-Loss Diet in a Rat Model for Postmenopausal Obesity.

Higher protein (>30% of total energy, HP)-energy restriction (HP-ER) diets are an effective means to improve body composition and metabolic health. However, weight loss (WL) is associated with bone loss, and the impact of HP-ER diets on bone is mixed and controversial. Recent evidence suggests conflicting outcomes may stem from differences in age, hormonal status, and the predominant source of dietary protein consumed. Therefore, this study investigated the effect of four 12-week energy restriction (ER) diets varying in predominate protein source (beef, milk, soy, casein) and protein quantity (normal protein, NP 15% vs. high, 35%) on bone and body composition outcomes in 32-week-old obese, ovariectomized female rats. Overall, ER decreased body weight, bone quantity (aBMD, aBMC), bone microarchitecture, and body composition parameters. WL was greater with the NP vs. HP-beef and HP-soy diets, and muscle area decreased only with the NP diet. The HP-beef diet exacerbated WL-induced bone loss (increased trabecular separation and endocortical bone formation rates, lower bone retention and trabecular BMC, and more rod-like trabeculae) compared to the HP-soy diet. The HP-milk diet did not augment WL-induced bone loss. Results suggest that specific protein source recommendations may be needed to attenuate the adverse alterations in bone quality following an HP-ER diet in a model of postmenopausal obesity.

Interactive effects of various loading parameters on the fluid dynamics within the lacunar-canalicular system for a single osteocyte.

The osteocyte lacunar-canalicular system (LCS) serves as a mechanotransductive core where external loading applied to the skeleton is transduced into mechanical signals (e.g., fluid shear) that can be sensed by mechanosensors (osteocytes). The fluid velocity and shear stress within the LCS are affected by various loading parameters. However, the interactive effect of distinct loading parameters on the velocity and shear stress in the LCS remains unclear. To address this issue, we developed a multiscale modeling approach, combining a poroelastic finite element (FE) model with a single osteocytic LCS unit model to calculate the flow velocity and shear stress within the LCS. Next, a sensitivity analysis was performed to investigate individual and interactive effects of strain magnitude, strain rate, number of cycles, and intervening short rests between loading cycles on the velocity and shear stress around the osteocyte. Lastly, we developed a relatively simple regression model to predict those outcomes. Our results demonstrated that the strain magnitude or rate alone were the main factors affecting the velocity and shear stress; however, the combination of these two was not directly additive, and addition of a short rest between cycles could enhance the combination of these two related factors. These results show highly interactive effects of distinct loading parameters on fluid velocity and shear stress in the LCS. Specifically, our results suggest that an enhanced fluid dynamics environment in the LCS can be achieved with a brief number of load cycles combined with short rest insertion and high strain magnitude and rate.

Cancellous Bone May Have a Greater Adaptive Strain Threshold Than Cortical Bone.

Strain magnitude has a controlling influence on bone adaptive response. However, questions remain as to how and if cancellous and cortical bone tissues respond differently to varied strain magnitudes, particularly at a molecular level. The goal of this study was to characterize the time-dependent gene expression, bone formation, and structural response of the cancellous and cortical bone of female C57Bl/6 mice to mechanical loading by applying varying load levels (low: -3.5 N; medium: -5.2 N; high: -7 N) to the skeleton using a mouse tibia loading model. The loading experiment showed that cortical bone mass at the tibial midshaft was significantly enhanced following all load levels examined and bone formation activities were particularly elevated at the medium and high loads applied. In contrast, for the proximal metaphyseal cancellous bone, only the high load led to significant increases in bone mass and bone formation indices. Similarly, expression of genes associated with inhibition of bone formation (e.g., Sost) was altered in the diaphyseal cortical bone at all load levels, but in the metaphyseal cortico-cancellous bone only by the high load. Finite element analysis determined that the peak tensile or compressive strains that were osteogenic for the proximal cancellous bone under the high load were significantly greater than those that were osteogenic for the midshaft cortical tissues under the low load. These results suggest that the magnitude of the strain stimulus regulating structural, cellular, and molecular responses of bone to loading may be greater for the cancellous tissues than for the cortical tissues. © 2021 The Authors. JBMR Plus published by Wiley Periodicals LLC on behalf of American Society for Bone and Mineral Research.

Anatomical variations in cortical bone surface permeability: Tibia versus femur.

Cortical bone surfaces (periosteal and endosteal) exhibit differential (re)modelling response to mechanical loading. This poses a serious challenge in establishing an in silico model to predict site-specific new bone formation as a function of mechanical stimulus. In this regard, mechanical loading-induced fluid motion in lacunar-canalicular system (LCS) is assumed osteogenic. Micro-architectural properties, especially permeability regulate canalicular fluid motion within the bone. The knowledge of these properties is required to compute flow distribution. Along the same line, it is possible that cortical surfaces may experience differential fluid distribution due to anatomical variations in microarchitectural properties which may induce distinct new bone response at cortical surfaces. Nevertheless, these properties are not well reported for cortical surfaces in the literature. Accordingly, the present study aims to measure microarchitectural properties especially permeability at different anatomical locations (medial, lateral, anterior, and posterior) of periosteal and endosteal surfaces using nanoindentation. A standard poroelastic optimization technique was used to estimate permeability, shear modulus, and Poisson's ratio. The properties are also compared for two weight-bearing bones i.e. tibia and femur. Endosteal surface was found more permeable as compared to the periosteal surface. Tibial endosteal surface had shown greater permeability values at most of the anatomical locations as compared to femoral endosteal surface. The outcomes may be used to precisely predict site-specific osteogenesis in cortical bone as a function of canalicular flow distribution. This work may ultimately be beneficial in designing the loading parameters to stimulate desired new bone response for the prevention and the cure of bone loss.

Insertional characteristics of three types of transfixation pin taps in third metacarpal bones from equine cadavers.

OBJECTIVE: To compare heat generation and mechanical bone damage achieved with 2 tapered and 1 cylindrical transfixation pin taps in third metacarpal bones from equine cadavers. SAMPLE: 18 pairs (36 specimens) of third metacarpal bones from euthanized horses with no known metacarpal disease. PROCEDURES: In each bone, an investigator drilled 3 holes for placement of a 6.3-mm cylindrical transfixation pin, a 6.3-mm tapered pin using a prototype tapered tap, and a 6.3-mm tapered pin using a revised tapered tap. One bone of each pair was tapped by hand and the other with an electric drill. Temperatures of the drill bits, reamers, and taps were measured and used to compare heat generation among tap groups and tapping methods (hand vs power tapping). Macrodamage (all bone pairs) and microdamage (6 bone pairs) were assessed. RESULTS: The revised tapered tap resulted in less heat generation and less total thread microdamage, compared with the prototype tapered and cylindrical taps. Power tapping created less bone damage but higher temperatures than did hand tapping for all bone groups. CONCLUSIONS AND CLINICAL RELEVANCE: The revised tap design for tapered pin insertion was superior to the prototype tap design and yielded similar or less bone damage than achieved with cylindrical pin insertion in equine third metacarpal bone specimens. We recommend careful hand tapping for tapered pin insertion rather than power tapping, which generated greater heat. The revised tapered tap could be expected to perform better than a cylindrical pin tap in terms of thermal and mechanical microdamage and should be used for insertion of tapered transfixation pins.

Murine Axial Compression Tibial Loading Model to Study Bone Mechanobiology: Implementing the Model and Reporting Results.

In vivo, tibial loading in mice is increasingly used to study bone adaptation and mechanotransduction. To achieve standardized and defined experimental conditions, loading parameters and animal-related factors must be considered when performing in vivo loading studies. In this review, we discuss these loading and animal-related experimental conditions, present methods to assess bone adaptation, and suggest reporting guidelines. This review originated from presentations by each of the authors at the workshop "Developing Best Practices for Mouse Models of In Vivo Loading" during the Preclinical Models Section at the Orthopaedic Research Society Annual Meeting, San Diego, CA, March 2017. Following the meeting, the authors engaged in detailed discussions with consideration of relevant literature. The guidelines and recommendations in this review are provided to help researchers perform in vivo loading experiments in mice, and thus further our knowledge of bone adaptation and the mechanisms involved in mechanotransduction. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 38:233-252, 2020.

Finite Element Analysis of Six Transcortical Pin Parameters and Their Effect on Bone-Pin Interface Stresses in the Equine Third Metacarpal Bone.

OBJECTIVE: The objectives of this study were to validate a finite element model of the equine distal limb transfixation cast and to determine the effect of six transcortical pin parameters on bone-pin interface (BPI) stresses in the third metacarpal bone. STUDY DESIGN: A transfixation cast finite element model was developed from a computed tomography scan of the third metacarpal bone and modelled pin elements. The model was validated by comparing strain measured around a 6.3-mm transfixation pin in the third metacarpal bone with the finite element model. The pin parameters of diameter, number, location, spacing, orientation and material were evaluated by comparing a variety of pin configurations within the model. RESULTS: Pin diameter and number had the greatest impact on BPI stress. Increasing the diameter and number of pins resulted in lower BPI stresses. Diaphyseal pin location and stainless-steel pins had lower BPI stresses than metaphyseal location and titanium alloy pins, respectively. Offset pin orientation and pin spacing had minimal impact on BPI stresses during axial loading. CONCLUSION: The results provide evidence that diameter and number are the main pin parameters affecting BPI stress in an equine distal limb transfixation cast. Configurations of various pin size and number may be proposed to reduce BPI stresses and minimize the risk of pin related complications. Further refinement of these models will be required to optimize pin configurations to account for pin hole size and its impact on overall bone strength.

Bone adaptation: Safety factors and load predictability in shaping skeletal form.

Much is known about skeletal adaptation in relation to the mechanical functions that bones serve. This includes how bone adapts to mechanical loading during an individual's lifetime as well as over evolutionary time. Although controlled loading in animal models allows us to observe short-term bone adaptation (epigenetic mechanobiology), examining an assemblage of extant vertebrate bones or a group of fossils' bony structures can reveal the combined effects of long-term trends in loading history and the effects of natural selection. In this survey we examine adaptations that take place over both time scales and highlight a few of the extraordinary insights first published by John Currey. First, we provide a historical perspective on bone adaptation control mechanisms, followed by a discussion of safety factors in bone. We then summarize examples of structural- and material-level adaptations and mechanotransduction, and analyze the relationship between these structural- and material-level adaptations observed in situations where loading modes are either predictable or unpredictable. We argue that load predictability is a major consideration for bone adaptation broadly across an evolutionary timescale, but that its importance can also be seen during ontogenetic growth trajectories, which are subject to natural selection as well. Furthermore, we suggest that bones with highly predictable load patterns demonstrate more precise design with lower safety factors, while bones that experience less predictable loads or those that are less capable of repair and adaptation are designed with a higher safety factor. Finally, exposure to rare loading events with high potential costs of failure leads to design of structures with very high safety factor compared to everyday loading experience. Understanding bone adaptations at the structural and material levels, which take place over an individual's lifetime or over evolutionary time has numerous applications in translational and clinical research to understand and treat musculoskeletal diseases, as well as to permit the furthering of human extraterrestrial exploration in environments with altered gravity.

The effects of growth rate and biomechanical loading on bone laminarity within the emu skeleton.

The orientation of vascular canals in primary bone may reflect differences in growth rate and/or adaptation to biomechanical loads. Previous studies link specific canal orientations to bone growth rates, but results between different taxa are contradictory. Circumferential vascular canals (forming laminar bone) have been hypothesized to reflect either (or both) rapid growth rate or locomotion-induced torsional loading. Previous work on the hindlimb biomechanics in the emu shows that the femur and tibiotarsus experience large shear strains, likely resulting from torsional loads that increase through ontogeny. Here, we test how growth rate and biomechanical loading affect bone laminarity in wing and hindlimb elements from growing emu (2-60 wks). If laminar bone is an adaptation to torsion-induced shear strains, it should increase from juveniles to adults. Alternatively, if bone laminarity reflects rapid growth, as has been shown previously in emu, it should be abundant in fast-growing juveniles and decrease with age. Transverse mid-shaft histological sections from the limb bones (femur, tibiotarsus, humerus, ulna, and radius) were prepared and imaged. Growth rates were measured using fluorescent bone labels. Vascular canal orientation was quantified using laminarity index (proportion of circumferential canals). Principal components analysis was performed to convert highly correlated variables (i.e., mass, age, growth rate, and shear strain) into principal components. Random-intercept beta regression modeling determined which principal components best explained laminarity. The fastest growth rates were found in young individuals for all five skeletal elements. Maximum growth rate did not coincide with peak laminarity. Instead, in the femur and tibiotarsus, elevated laminarity is strongly correlated with adult features such as large size, old age, and modest growth rate. This result is contrary to predictions made based on a previous study of emu but is consistent with results observed in some other avian species (penguin, chicken). Shear strain in the caudal octant of the femur and tibiotarsus is positively correlated with laminarity but has a weaker effect on laminarity relative to mass, age, and growth rate. Laminarity in the wing elements is variable and does not correlate with ontogenetic factors (including mass, age, and growth rate). Its presence may relate to relaxed developmental canalization or a retained ancestral feature. In conclusion, ontogeny (including growth rate) is the dominant influence on vascular canal orientation at least in the hindlimb of the emu.

Adaptive changes in micromechanical environments of cancellous and cortical bone in response to in vivo loading and disuse.

The skeleton accommodates changes in mechanical environments by increasing bone mass under increased loads and decreasing bone mass under disuse. However, little is known about the adaptive changes in micromechanical behavior of cancellous and cortical tissues resulting from loading or disuse. To address this issue, in vivo tibial loading and hindlimb unloading experiments were conducted on 16-week-old female C57BL/6J mice. Changes in bone mass and tissue-level strains in the metaphyseal cancellous and midshaft cortical bone of the tibiae, resulting from loading or unloading, were determined using microCT and finite element (FE) analysis, respectively. We found that loading- and unloading-induced changes in bone mass were more pronounced in the cancellous than cortical bone. Simulated FE-loading showed that a greater proportion of elements experienced relatively lower longitudinal strains following load-induced bone adaptation, while the opposite was true in the disuse model. While the magnitudes of maximum or minimum principal strains in the metaphyseal cancellous and midshaft cortical bone were not affected by loading, strains oriented with the long axis were reduced in the load-adapted tibia suggesting that loading-induced micromechanical benefits were aligned primarily in the loading direction. Regression analyses demonstrated that bone mass was a good predictor of bone tissue strains for the cortical bone but not for the cancellous bone, which has complex microarchitecture and spatially-variant strain environments. In summary, loading-induced micromechanical benefits for cancellous and cortical tissues are received primarily in the direction of force application and cancellous bone mass may not be related to the micromechanics of cancellous bone.

Comparison of insertion characteristics of tapered and cylindrical transfixation pins in third metacarpal bones of equine cadavers.

OBJECTIVE To compare heat generation and mechanical bone damage for tapered and cylindrical transfixation pins during drilling, tapping, and pin insertion in equine third metacarpal bones. SAMPLE 16 pairs of cadaveric equine third metacarpal bones. PROCEDURES For cylindrical pin insertion, a 6.2-mm hole was drilled and tapped with a cylindrical tap, and then a standard 6.3-mm pin was inserted. For tapered pin insertion, a 6.0-mm hole was drilled, reamed with a tapered reamer, and tapped with a tapered tap, and then a 6.3-mm tapered pin was inserted. Paired t tests and 1-way ANOVAs were used to compare heat generation (measured by use of thermocouples and thermography), macrodamage (assessed by use of stereomicroscopy), and microdamage (assessed by examination of basic fuchsin-stained histologic specimens) between cylindrical and tapered pins and between tapered pins inserted to various insertion torques. RESULTS Tapered pin insertion generated less heat but resulted in more bone damage than did cylindrical pin insertion when pins were inserted to the same insertion torque. Insertion of tapered pins to increasing insertion torques up to 16 N•m resulted in increased heat generation and bone damage. CONCLUSIONS AND CLINICAL RELEVANCE Tapered pin insertion resulted in lower heat production than did cylindrical pin insertion. However, tapered pin insertion resulted in greater bone damage, which likely was attributable to differences in the tapered and cylindrical taps. A tapered pin may be preferable to a cylindrical pin for insertion in equine cortical bone provided that improvements in tap design can reduce bone damage during insertion.

Densification of Type I Collagen Matrices as a Model for Cardiac Fibrosis.

Cardiac fibrosis is a disease state characterized by excessive collagenous matrix accumulation within the myocardium that can lead to ventricular dilation and systolic failure. Current treatment options are severely lacking due in part to the poor understanding of the complexity of molecular pathways involved in cardiac fibrosis. To close this gap, in vitro model systems that recapitulate the defining features of the fibrotic cellular environment are in need. Type I collagen, a major cardiac extracellular matrix protein and the defining component of fibrotic depositions, is an attractive choice for a fibrosis model, but demonstrates poor mechanical strength due to solubility limits. However, plastic compression of collagen matrices is shown to significantly increase its mechanical properties. Here, confined compression of oligomeric, type I collagen matrices is utilized to resemble defining hallmarks seen in fibrotic tissue such as increased collagen content, fibril thickness, and bulk compressive modulus. Cardiomyocytes seeded on compressed matrices show a strong beating abrogation as observed in cardiac fibrosis. Gene expression analysis of selected fibrosis markers indicates fibrotic activation and cardiomyocyte maturation with regard to the existing literature. With these results, a promising first step toward a facile heart-on-chip model is presented to study cardiac fibrosis.

Effects of Loading Duration and Short Rest Insertion on Cancellous and Cortical Bone Adaptation in the Mouse Tibia.

The skeleton's osteogenic response to mechanical loading can be affected by loading duration and rest insertion during a series of loading events. Prior animal loading studies have shown that the cortical bone response saturates quickly and short rest insertions between load cycles can enhance cortical bone formation. However, it remains unknown how loading duration and short rest insertion affect load-induced osteogenesis in the mouse tibial compressive loading model, and particularly in cancellous bone. To address this issue, we applied cyclic loading (-9 N peak load; 4 Hz) to the tibiae of three groups of 16 week-old female C57BL/6 mice for two weeks, with a different number of continuous load cycles applied daily to each group (36, 216 and 1200). A fourth group was loaded under 216 daily load cycles with a 10 s rest insertion after every fourth cycle. We found that as few as 36 load cycles per day were able to induce osteogenic responses in both cancellous and cortical bone. Furthermore, while cortical bone area and thickness continued to increase through 1200 cycles, the incremental increase in the osteogenic response decreased as load number increased, indicating a reduced benefit of the increasing number of load cycles. In the proximal metaphyseal cancellous bone, trabecular thickness increased with load up to 216 cycles. We also found that insertion of a 10 s rest between load cycles did not improve the osteogenic response of the cortical or cancellous tissues compared to continuous loading in this model given the age and sex of the mice and the loading parameters used here. These results suggest that relatively few load cycles (e.g. 36) are sufficient to induce osteogenic responses in both cortical and cancellous bone in the mouse tibial loading model. Mechanistic studies using the mouse tibial loading model to examine bone formation and skeletal mechanobiology could be accomplished with relatively few load cycles.

Experimental tests of planar strain theory for predicting bone cross-sectional longitudinal and shear strains.

Understanding of the diversity of skeletal loading regimes in vertebrate long bones during locomotion has been significantly enhanced by the application of planar strain theory (PST) to in vivo bone strain data. PST is used to model the distribution of longitudinal strains normal to the bone's transverse cross-section and the location of the neutral axis of bending. To our knowledge, the application of this theory to skeletal biomechanics has not been experimentally validated. We evaluated the accuracy of PST using strain measurements from emu tibiotarsi instrumented with four strain gauges and loaded in ex vivo four-point bending. Using measured strains from three-gauge combinations, PST was applied to predict strain values at a fourth gauge's location. Experimentally measured and predicted strain values correlated linearly with a slope near 1.0, suggesting that PST accurately predicts longitudinal strains. Additionally, we assessed the use of PST to extrapolate shear strains to locations on a bone not instrumented with rosette strain gauges. Guineafowl tibiotarsi were instrumented with rosette strain gauges and in vivo longitudinal and shear strains were measured during treadmill running. Individual-specific and sample-mean ratios between measured longitudinal strains from the medial and posterior bone surfaces were used to extrapolate posterior-site shear strain from shear strains measured on the medial surface. Measured and predicted shear strains at the posterior gauge site using either ratio showed trends for a positive correlation between measured and predicted strains, but the correlation did not equal 1.0 and had a non-zero intercept, suggesting that the use of PST should be carefully considered in the context of the goals of the study and the desired precision for the predicted shear strains.

Effects of conventional and slanted ventral slot procedures on the biomechanical behavior of the C5-C6 vertebral motion unit in dogs.

OBJECTIVE To compare the effects of conventional and slanted ventral slot procedures on the biomechanical behavior of the C5-C6 vertebral motion unit (VMU) in dogs. SAMPLE 14 vertebral columns (C4 through C7) from canine cadavers. PROCEDURES Specimens were assigned to a conventional or slanted ventral slot group (n = 7/group). For each specimen, the C5-C6 VMU was tested in ventral and dorsal bending and positive and negative axial torsion before and after surgery. Range of motion (ROM), stiffness, and energy absorption were compared between the 2 groups. RESULTS Both procedures significantly increased the ROM and stiffness and significantly decreased the energy absorption of the C5-C6 VMU in ventral and dorsal bending. Both procedures also increased the ROM in positive and negative axial torsion. In negative torsion, total stiffness and stiffness over the maximum ROM tested decreased less for the slanted slot procedure than for the conventional slot procedure. There were no significant differences between procedures for any of the other biomechanical outcomes examined. CONCLUSIONS AND CLINICAL RELEVANCE Results suggested that the biomechanical response of the C5-C6 VMU to the conventional and slanted ventral slot procedures was not significantly different, especially when considering postsurgical instability induced by both procedures. This was most likely due to disruption of the nucleus pulposus and dorsal annulus fibrosus of the disk with both procedures. On the basis of these findings, neither procedure appeared biomechanically superior. Comparative clinical studies are warranted to further evaluate the 2 procedures.

Effects of Deletion of ERα in Osteoblast-Lineage Cells on Bone Mass and Adaptation to Mechanical Loading Differ in Female and Male Mice.

Estrogen receptor alpha (ERα) has been implicated in bone's response to mechanical loading in both males and females. ERα in osteoblast lineage cells is important for determining bone mass, but results depend on animal sex and the cellular stage at which ERα is deleted. We demonstrated previously that when ERα is deleted from mature osteoblasts and osteocytes in mixed-background female mice, bone mass and strength are decreased. However, few studies exist examining the skeletal response to loading in bone cell-specific ERαKO mice. Therefore, we crossed ERα floxed (ERα(fl/fl)) and osteocalcin-Cre (OC-Cre) mice to generate animals lacking ERα in mature osteoblasts and osteocytes (pOC-ERαKO) and littermate controls (LC). At 10 weeks of age, the left tibia was loaded in vivo for 2 weeks. We analyzed bone mass through micro-CT, bone formation rate by dynamic histomorphometry, bone strength from mechanical testing, and osteoblast and osteoclast activity by serum chemistry and immunohistochemistry. ERα in mature osteoblasts differentially regulated bone mass in males and females. Compared with LC, female pOC-ERαKO mice had decreased cortical and cancellous bone mass, whereas male pOC-ERαKO mice had equal or greater bone mass than LC. Bone mass results correlated with decreased compressive strength in pOC-ERαKO female L(5) vertebrae and with increased maximum moment in pOC-ERαKO male femora. Female pOC-ERαKO mice responded more to mechanical loading, whereas the response of pOC-ERαKO male animals was similar to their littermate controls.