Critical conditions for liquid chromatography of statistical polyolefins: Evaluation of diene distribution in EPDM terpolymers.

Liquid chromatography at critical conditions is of interest as it may unravel molecular information on macromolecular structures not accessible by any other analytical techniques. Yet so far, such conditions have never been experimentally established for copolymers, where a particular need for such information exists. Toward this goal, critical conditions for statistical ethylene propylene copolymers were identified. In the first approach the composition of the binary mobile phase was varied at a constant temperature, and secondly by modulating the adsorption-desorption temperature at constant mobile phase composition. Solvents for both methods were identified by using a novel approach that combines structure retention relationships with Hansen Solubility Parameters. As a result, for the first time, the heterogeneity of an ethylene propylene diene terpolymer sample with regard to the pendant double bond of the diene could be determined. The novel chromatographic approach was validated by measuring the composition of fractions taken over the chromatographic run offline by nuclear magnetic resonance. In summary, this work gave the first experimental evidence for the existence of critical conditions for polyolefin random copolymers, as postulated by Brun. This novel chromatographic approach holds immense potential to engineer complex polymers towards future applications by making use of the now-accessible molecular information.

Separation of ethylene-norbornene copolymers using high performance liquid chromatography.

The elution behavior of ethylene-norbornene (EN) copolymers prepared with various catalysts was studied in selected binary solvent gradients using porous graphite (HypercarbTM) as stationary phase. It was found that the elution volumes of the EN copolymers correlated with their average norbornene content. For a series with norbornene content lower than 20 mol % the correlation was positive (i.e. increasing elution volumes with increasing norbornene content), whereas for a series with norbornene contents above 20 mol % it was negative (decreasing elution volumes with increasing norbornene content). It is known that EN copolymers have complicated microstructures that depend on norbornene content and the catalyst system used for synthesis. Thus, it is supposed that the opposing trends in the elution behavior of the EN copolymers are caused by differences in their microstructure, ultimately governed by the norbornene content. Our conclusions are supported by results from NMR spectroscopy, which revealed the microstructure, and differential scanning calorimetry (DSC).

Analysis of the molecular heterogeneity of poly(lactic acid)/poly(butylene succinate-co-adipate) blends by hyphenating size exclusion chromatography with nuclear magnetic resonance and infrared spectroscopy.

The compositional and stereochemical heterogeneity of copolymers are key molecular metrics, and their knowledge is of pivotal importance for evidence based material development. Yet, while it is state of the art to determine these parameters for many petroleum based polymers, little insight exists in that regard for bio-based materials. Towards this end, size exclusion chromatography (SEC) was hyphenated with nuclear magnetic resonance spectroscopy (NMR) in an offline manner and a blend of poly(lactic acid) (PLA) and poly(butylene succinate-co-adipate) (PBSA) investigated. Thus, the microstructural heterogeneity could be shown with regard to tacticity of the PLA and regioregularity of the PBSA component. The results show, that the highest molar mass fraction differs in stereochemical composition from the others. It may be assumed that this is the result of misinsertions with regard to stereochemistry occurring during the catalytic polymerization of the lactide. While the content of both constituent polymers along the molar mass axis could be well studied using a univariate analysis of the infrared (IR) spectra, this method failed to profile the adipate and succinate content individually. For this purpose, SEC was coupled to IR spectroscopy in online mode and the spectra were evaluated by a multivariate protocol. Thus, the content of each monomer along the molar mass distribution could be mapped with high chromatographic resolution.

Characterization of functionalized polyolefins by high-temperature two-dimensional liquid chromatography.

High-temperature two-dimensional liquid chromatography (HT 2D-LC) was developed for the separation and characterization of functional polyolefins. Therefore, the key experimental parameters, namely the injection volume, the mobile phase composition, the flow rate in SEC and the time and phase of sampling into the second dimension, were systematically varied and their influence on the resolution of separation were studied. The HPLC separation of ethylene-vinylacetate waxes was realized using silica gel as stationary phase and a solvent gradient decalin→cyclohexanone, while SEC separations were realized in the chromatographic system polystyrene divinyl benzene column/1,2,4-trichlorobenzene. By choosing suitable experimental parameters, the run time needed for one complete 2D-LC analysis of a polymer sample was shortened from about 200 min to 100 min. However, the developed method failed to adsorb polypropylene and ethylene/1-butene copolymers grafted with 13 or 3 mol.% of methyl methacrylate respectively. Using porous graphite as a stationary phase and a solvent gradient 1-decanol→1,2,4-trichlorobenzene as mobile phase 2D-LC separations of both grafted polyolefins were realized.

Characterization of multiblock copolymers by chromatographic techniques.

Multiblock copolymers (MBC) composed of blocks of poly(1,4-dioxanone) (PPDO) and poly(e-caprolactone) (PCL) were investigated in order to gain information on the extend of chemical heterogeneity of the samples. A gradient chromatographic method was established allowing separation of purely PPDO- from purely PCL-containing chains. Application of the gradient to MBC made of PPDO- and PCL-diols connected by trimethylhexamethylene diisocyanate (TMDI) resulted in two well separated peaks which were analyzed by means of FTIR, 1H-NMR and pyrolysis GC-MS. It was shown that the first peak was composed to a large extent of PPDO and only lower amounts of PCL were incorporated. Conversely, the second peak consisted predominantly of PCL with only a minor fraction of PPDO. Thus, the MBCs having PPDO and PCL segments show an unexpected broad chemical heterogeneity.

Synthesis of methyl 4'-O-methyl-beta-D-cellobioside-13C12 from D-glucose-13C6. Part 2: solid-state NMR studies.

Double Quantum (DQ) NMR, which utilizes the magnetic dipole interaction between the (13)C atoms, was used for the complete assignment of the (13)C NMR resonances to the corresponding carbon ring positions for the monoclinic and triclinic allomorphs of methyl 4'-O-methyl-beta-D-cellobioside-(13)C(12)(1-(13)C(12)), a cellodextrin model compound of cellulose (13)C-perlabeled at the cellobiose core. The through-space interactions were used to identify the direct chemical bonds between adjacent carbon atoms in the rings. More importantly, the (13)C NMR signals of the carbon sites C1' and C4 involved in the glycosidic bond were identified. This allowed for the complete (13)C chemical shift assignment, that when combined with the X-ray crystallography data provides a complete characterization.

Purity assessment problem in quantitative NMR--impurity resonance overlaps with monitor signal multiplets from stereoisomers.

This paper describes the situation that can emerge when the signals to be evaluated in quantitative NMR measurements-so-called "monitor signals"--consist of several resonance lines from the stereoisomers of the analyte in addition to an impurity signal underneath. The monitor signal problem is demonstrated in the purity assessment of two samples of 2-(isopropylamino)-4-(ethylamino)-6-chloro-1,3,5-triazine (atrazine), a common herbizide which served as analyte in a CCQM intercomparison. It is shown that, in DMSO-d6 solution, a mixture of stereoisomers leads to several individual overlapping singlets, which are further split by spin-spin coupling. A measurement protocol was developed for finding and identifying an impurity that has a signal that is positioned precisely beneath the methyl signal chosen as the monitor signal in one of the samples. Quantitative NMR purity assessment is still possible in this special case, but with higher uncertainty.