Recycled Polypropylene/Strontium Ferrite Polymer Composite Materials with Electromagnetic Shielding Properties.

This paper presents the obtaining and characterization of recycled polypropylene/strontium ferrite (PP/SrFe12O19) polymer composite materials with applications in the electromagnetic shielding of vehicle interiors (mainly automotive electronics-carcasses) from the electromagnetic radiation emitted mainly by exterior sources-electrical lines and supply sources-in terms of the development of the new electrical vehicles. With this aim, suitable polymer composite materials were developed using SrFe12O19 filler in two forms (powder and concentrate). The recycled PP polymer and composite materials with a PP/SrFe12O19 weight ratio of 75/25 and 70/30 were obtained in two stages, i.e., pellets by extrusion and samples for testing through a melt injection process. The characterization of the obtained materials took into account the requirements imposed by the desired applications. It consisted of determining the mechanical and dielectric properties, and microstructure analyses, along with the determination of the resistance to the action of a temperature of 70 °C, which is higher than the temperatures created during the summer inside vehicles. The performance of these materials as electromagnetic shields was assessed through functional tests consisting of the determination of magnetic permeability and the estimation of the electromagnetic shielding efficiency (SE). The obtained results confirmed the improvement of the mechanical, dielectric, and magnetic properties of the PP/SrFe12O19 composites compared to the selected PP polymers. It is also found that all the composite materials exhibited reflective shielding properties (SER from -71.5 dB to -56.7 dB), with very little absorption shielding. The most performant material was the composite made of PP/SrFe12O19 powder with a weight ratio of 70/30. The promising results recommend this composite material for potential use in automotive shielding applications against electromagnetic pollution.

Simultaneously Recovery of Thorium and Tungsten through Hybrid Electrolysis-Nanofiltration Processes.

The recovery and recycling of metals that generate toxic ions in the environment is of particular importance, especially when these are tungsten and, in particular, thorium. The radioactive element thorium has unexpectedly accessible domestic applications (filaments of light bulbs and electronic tubes, welding electrodes, and working alloys containing aluminum and magnesium), which lead to its appearance in electrical and electronic waste from municipal waste management platforms. The current paper proposes the simultaneous recovery of waste containing tungsten and thorium from welding electrodes. Simultaneous recovery is achieved by applying a hybrid membrane electrolysis technology coupled with nanofiltration. An electrolysis cell with sulphonated polyether-ether-ketone membranes (sPEEK) and a nanofiltration module with chitosan-polypropylene membranes (C-PHF-M) are used to carry out the hybrid process. The analysis of welding electrodes led to a composition of W (tungsten) 89.4%; Th 7.1%; O2 2.5%; and Al 1.1%. Thus, the parameters of the electrolysis process were chosen according to the speciation of the three metals suggested by the superimposed Pourbaix diagrams. At a constant potential of 20.0 V and an electrolysis current of 1.0 A, the pH is varied and the possible composition of the solution in the anodic workspace is analyzed. Favorable conditions for both electrolysis and nanofiltration were obtained at pH from 6 to 9, when the soluble tungstate ion, the aluminum hydroxide, and solid thorium dioxide were formed. Through the first nanofiltration, the tungstate ion is obtained in the permeate, and thorium dioxide and aluminum hydroxide in the concentrate. By adding a pH 13 solution over the two precipitates, the aluminum is solubilized as sodium aluminate, which will be found after the second nanofiltration in the permeate, with the thorium dioxide remaining integrally (within an error of ±0.1 ppm) on the C-PHF-M membrane.

CoxCrFeNiTi High-Entropy Alloys Prepared via Mechanical Alloying and Spark Plasma Sintering for Magnetron Sputtering Coatings.

The main objective of this study was to develop a high-entropy alloy (HEA) derived from the CoxCrFeNiTi HEA system (x = 0.5, 1) for protective coatings using the magnetron sputtering method. In order to produce the high-entropy alloy targets required for the magnetron sputtering process, mechanically alloyed metallic powders were consolidated via spark plasma sintering (SPS). The microstructural analysis results of the HEA mixture presented morphology changes after 30 h of alloying, with the particles presenting uniform polygonal shapes and dimensions. Subsequently, 316L stainless steel (SS) specimens were coated via magnetron sputtering, comparing their composition with that of the sputtering targets used for deposition to establish stoichiometry. Microstructural analyses of the SPSed HEAs revealed no defects and indicated a uniform elemental distribution across the surface. Furthermore, the CoCrFeNiTi equiatomic alloy exhibited a nearly stoichiometric composition, both in the coating and the sputtering target. The XRD analysis results indicated that amorphous coatings were obtained for both Co0.5CrFeNiTi and the CoCrFeNiTi HEA, and nanoindentation tests indicated that the CoCrFeNiTi HEA coating presented a hardness of 596 ± 22 HV, compared to the 570 ± 19 HV measured for Co0.5CrFeNiTi, suggesting an improved wear resistance.

Special Packaging Materials from Recycled PET and Metallic Nano-Powders.

The European methodology for plastics, as a feature of the EU's circular economy activity plan, ought to support the decrease in plastic waste. The improvement of recycled plastics' economics and quality is one important part of this action plan. Additionally, achieving the requirement that all plastic packaging sold in the EU by 2030 be recyclable or reusable is an important objective. This means that food packaging materials should be recycled in a closed loop at the end. One of the most significant engineering polymers is polyethylene terephthalate (PET), which is widely used. Due to its numerous crucial qualities, it has a wide variety of applications, from packaging to fibers. The thermoplastic polyolefin, primarily polyethylene and polypropylene (PP), is a popular choice utilized globally in a wide range of applications. In the first phase of the current experiment, the materials were obtained by hot pressing with the press machine. The reinforcer is made of Al nanopowder 800 nm and Fe nanopowder 790 nm and the quality of the recycled polymer was examined using Fourier transform infrared spectroscopy (FTIR), a scanning electron microscope (SEM), and differential scanning calorimetry (DSC). From DSC variation curves as a function of temperature, the values from the transformation processes (glass transition, crystallization, and melting) are obtained. SEM measurements revealed that the polymer composites with Al have smooth spherical particles while the ones with Fe have bigger rough spherical particles.

Flexible Electromagnetic Shielding Nano-Composites Based on Silicon and NiFe2O4 Powders.

In this paper, the obtaining and characterization of five experimental models of novel polymer composite materials with ferrite nano-powder are presented. The composites were obtained by mechanically mixing two components and pressing the obtained mixture on a hot plate press. The ferrite powders were obtained by an innovative economic co-precipitation route. The characterization of these composites consisted of physical and thermal properties: hydrostatic density, scanning electron microscopy (SEM), and TG DSC thermal analyses, along with functional electromagnetic tests in order to demonstrate the functionality of these materials as electromagnetic shields (magnetic permeability, dielectric characteristics, and shielding effectiveness). The purpose of this work was to obtain a flexible composite material, applicable to any type of architecture for the electrical and automotive industry, necessary for protection against electromagnetic interference. The results demonstrated the efficiency of such materials at lower frequencies, but also in the microwave domain, with higher thermal stability and lifetime.

Bioremediation of Wastewater Using Yeast Strains: An Assessment of Contaminant Removal Efficiency.

The main goal of wastewater treatment is to significantly reduce organic compounds, micronutrients (nitrogen and phosphorus) and heavy metals and other contaminants (pathogens, pharmaceuticals and industrial chemicals). In this work, the efficiency of removing different contaminants (COD, NO3-, NO2-, NH4+, PO43-, SO42-, Pb2+, Cd2+) from synthetic wastewater was tested using five different yeast strains: Kluyveromyces marxianus CMGBP16 (P1), Saccharomyces cerevisiae S228C (P2), Saccharomyces cerevisiae CM6B70 (P3), Saccharomyces cerevisiae CMGB234 (P4) and Pichia anomala CMGB88 (P5). The results showed a removal efficiency of up to 70% of COD, 97% of nitrate, 80% of nitrite, 93% of phosphate and 70% of sulfate ions for synthetic wastewater contaminated with Pb2+ (43 mg/L) and Cd2+ ions (39 mg/L). In contrast, the results showed an increase in ammonium ions, especially in the presence of Pb2+ ions. The yeast strains showed a high capacity to reduce Pb2+ (up to 96%) and Cd2+ (up to 40%) ions compared to the initial concentrations. In presence of a crude biosurfactant, the removal efficiency increased up to 99% for Pb2+ and 56% for Cd2+ simultaneously with an increase in yeast biomass of up to 11 times. The results, which were obtained in the absence of aeration and in neutral pH conditions, proved a high potential for practical applications in the biotreatment of the wastewater and the recovery of Pb and Cd ions, with a high benefit-cost ratio.

Structural Insights into LDPE/UHMWPE Blends Processed by γ-Irradiation.

Ultra-high-molecular-weight polyethylene (UHMWPE) matrices containing low-density polyethylene (LDPE), hydroxyapatite (HAp) as filler, and rosemary extract (RM) as stabilizer were investigated for their qualification for long-term applications. The significant contributions of the blend components were analyzed, and variations in mechanical properties, oxidation strength, thermal behavior, crystallinity, and wettability were discussed. SEM images of microstructural peculiarities completed the introspective survey. The stability improvement due to the presence of both additives was an increase in the total degradation period of 67% in comparison with an unmodified HDPE/UHMWPE blend when the materials were subjected to a 50 kGy γ-dose. There was growth in activation energies from 121 kJ mol-1 to 139 kJ mol-1 when HAp and rosemary extract delayed oxidation. The exposure of samples to the action of γ-rays was found to be a proper procedure for accomplishing accelerated oxidative degradation. The presence of rosemary extract and HAp powder significantly increased the thermal and oxidation resistances. The calculation of material lifetimes at various temperatures provided meaningful information on the wearability and integrity of the inspected composites.

Stability Study of the Irradiated Poly(lactic acid)/Styrene Isoprene Styrene Reinforced with Silica Nanoparticles.

In this paper, the stability improvement of poly(lactic acid) (PLA)/styrene-isoprene block copolymer (SIS) loaded with silica nanoparticles is characterized. The protection efficiency in the material of thermal stability is mainly studied by means of high accurate isothermal and nonisothermal chemiluminescence procedures. The oxidation induction times obtained in the isothermal CL determinations increase from 45 min to 312 min as the polymer is free of silica or the filler loading is about 10%, respectively. The nonisothermal measurements reveal the values of onset oxidation temperatures with about 15% when the concentration of SiO2 particles is enhanced from none to 10%. The curing assay and Charlesby-Pinner representation as well as the modifications that occurred in the FTIR carbonyl band at 1745 cm-1 are appropriate proofs for the delay of oxidation in hybrid samples. The improved efficiency of silica during the accelerated degradation of PLA/SIS 30/n-SiO2 composites is demonstrated by means of the increased values of activation energy in correlation with the augmentation of silica loading. While the pristine material is modified by the addition of 10% silica nanoparticles, the activation energy grows from 55 kJ mol-1 to 74 kJ mol-1 for nonirradiated samples and from 47 kJ mol-1 to 76 kJ mol-1 for γ-processed material at 25 kGy. The stabilizer features are associated with silica nanoparticles due to the protection of fragments generated by the scission of hydrocarbon structure of SIS, the minor component, whose degradation fragments are early converted into hydroperoxides rather than influencing depolymerization in the PLA phase. The reduction of the transmission values concerning the growing reinforcement is evidence of the capacity of SiO2 to minimize the changes in polymers subjected to high energy sterilization. The silica loading of 10 wt% may be considered a proper solution for attaining an extended lifespan under the accelerated degradation caused by the intense transfer of energy, such as radiation processing on the polymer hybrid.

Polymer Composites with Self-Regulating Temperature Behavior: Properties and Characterization.

A novel conductive composite material with homogeneous binary polymer matrix of HDPE (HD) and LLDPE (LLD), mixed with conductive filler consisting of carbon black (CB) and graphite (Gr), was tested against a HDPE composite with a similar conductive filler. Even the concentration of the conductive filler was deliberately lower for (CB + Gr)/(LLD + HD), and the properties of this composite are comparable or better to those of (CB + Gr)/HD. The kinetic parameters of the ρ-T curves and from the DSC curves indicate that the resistivity peak is obtained when the polymer matrix is fully melted. When subjected to repeated thermal cycles, the composite (CB + Gr)/(LLD + HD) presented a better electrical behavior than composite CB + Gr)/HD, with an increase in resistivity (ρmax) values with the number of cycles, as well as less intense NTC (Negative Temperature Coefficient) effects, both for the crosslinked and thermoplastic samples. Radiation crosslinking led to increased ρmax values, as well as to inhibition of NTC effects in both cases, thus having a clear beneficial effect. Limitation effects of surface temperature and current intensity through the sample were observed at different voltages, enabling the use of these materials as self-regulating heating elements at various temperatures below the melting temperature. The procedure based on physical mixing of the components appears more efficient in imparting lower resistivity in solid state and high PTC (Positive Temperature Coefficient) effects to the composites. This effect is probably due to the concentration of the conductive particles at the surface of the polymer domains, which would facilitate the formation of the conductive paths. Further work is still necessary to optimize both the procedure of composite preparation and the properties of such materials.

Nanopatterning of monolayer graphene by quantum optical lithography.

Quantum optical lithography, a diffraction-unlimited method, was applied to pattern monolayer graphene at 10 nm resolution. In our tests with chemical vapor deposition monolayer graphene samples, we have succeeded in producing flat surfaces of a sandwich of monolayer graphene-resist on Si, Si3N4, or glass substrates. Complex patterns have been written on monolayer graphene samples by a nanoablation process. The method could be used to realize monolayer graphene nanodevices.