NARX neural network model for strong resolution improvement in a distributed temperature sensor.

This paper proposes an approach to process the response of a distributed temperature sensor using a nonlinear autoregressive with external input neural network. The developed model is composed of three steps: extraction of characteristics, regression, and reconstruction of the signal. Such an approach is robust because it does not require knowledge of the characteristics of the signal; it has a reduction of data to be processed, resulting in a low processing time, besides the simultaneous improvement of spatial resolution and temperature. We obtain total correction of the temperature resolution and spatial resolution of 5 cm of the sensor.

Large area optical mapping of surface contact angle.

Top-down contact angle measurements have been validated and confirmed to be as good if not more reliable than side-based measurements. A range of samples, including industrially relevant materials for roofing and printing, has been compared. Using the top-down approach, mapping in both 1-D and 2-D has been demonstrated. The method was applied to study the change in contact angle as a function of change in silver (Ag) nanoparticle size controlled by thermal evaporation. Large area mapping reveals good uniformity for commercial Aspen paper coated with black laser printer ink. A demonstration of the forensic and chemical analysis potential in 2-D is shown by uncovering the hidden CsF initials made with mineral oil on the coated Aspen paper. The method promises to revolutionize nanoscale characterization and industrial monitoring as well as chemical analyses by allowing rapid contact angle measurements over large areas or large numbers of samples in ways and times that have not been possible before.

Air Flow Detection in Crude Oil by Infrared Light.

In this paper, we used infrared light in the range of 8-12 µm to develop and test an optical imaging system to detect air bubbles flowing in oil. The system basically comprises a broadband light source and a 31 × 32 thermopile array to generate images. To analyze the effects related to light absorption, reflection, and refraction on air-oil boundaries, a numerical model was developed and the predominance of the refraction instead of the absorption in bubbles with diameters below a certain critical value was observed. The IR region of the electromagnetic spectrum has both optical and thermic behavior. To understand the limits of each effect on the oil flow imaging, a study of the influence of temperature variation on the petroleum optical detection was performed. The developed optical imaging system allowed the detection of air flow in static oil and in oil-air two-phase flow. With the presented system, it was possible to achieve images through up to 12 mm of oil volumes, but this may be enhanced by the use of optimized IR sources and detectors.

Sparse Reconstruction for Temperature Distribution Using DTS Fiber Optic Sensors with Applications in Electrical Generator Stator Monitoring.

This paper presents an image reconstruction method to monitor the temperature distribution of electric generator stators. The main objective is to identify insulation failures that may arise as hotspots in the structure. The method is based on temperature readings of fiber optic distributed sensors (DTS) and a sparse reconstruction algorithm. Thermal images of the structure are formed by appropriately combining atoms of a dictionary of hotspots, which was constructed by finite element simulation with a multi-physical model. Due to difficulties for reproducing insulation faults in real stator structure, experimental tests were performed using a prototype similar to the real structure. The results demonstrate the ability of the proposed method to reconstruct images of hotspots with dimensions down to 15 cm, representing a resolution gain of up to six times when compared to the DTS spatial resolution. In addition, satisfactory results were also obtained to detect hotspots with only 5 cm. The application of the proposed algorithm for thermal imaging of generator stators can contribute to the identification of insulation faults in early stages, thereby avoiding catastrophic damage to the structure.

Single- and two-phase flow characterization using optical fiber bragg gratings.

Single- and two-phase flow characterization using optical fiber Bragg gratings (FBGs) is presented. The sensor unit consists of the optical fiber Bragg grating positioned transversely to the flow and fixed in the pipe walls. The hydrodynamic pressure applied by the liquid or air/liquid flow to the optical fiber induces deformation that can be detected by the FBG. Given that the applied pressure is directly related to the mass flow, it is possible to establish a relationship using the grating resonance wavelength shift to determine the mass flow when the flow velocity is well known. For two phase flows of air and liquid, there is a significant change in the force applied to the fiber that accounts for the very distinct densities of these substances. As a consequence, the optical fiber deformation and the correspondent grating wavelength shift as a function of the flow will be very different for an air bubble or a liquid slug, allowing their detection as they flow through the pipe. A quasi-distributed sensing tool with 18 sensors evenly spread along the pipe is developed and characterized, making possible the characterization of the flow, as well as the tracking of the bubbles over a large section of the test bed. Results show good agreement with standard measurement methods and open up plenty of opportunities to both laboratory measurement tools and field applications.

Fiber Bragg grating temperature sensors in a 6.5-MW generator exciter bridge and the development and simulation of its thermal model.

This work reports the thermal modeling and characterization of a thyristor. The thyristor is used in a 6.5-MW generator excitation bridge. Temperature measurements are performed using fiber Bragg grating (FBG) sensors. These sensors have the benefits of being totally passive and immune to electromagnetic interference and also multiplexed in a single fiber. The thyristor thermal model consists of a second order equivalent electric circuit, and its power losses lead to an increase in temperature, while the losses are calculated on the basis of the excitation current in the generator. Six multiplexed FBGs are used to measure temperature and are embedded to avoid the effect of the strain sensitivity. The presented results show a relationship between field current and temperature oscillation and prove that this current can be used to determine the thermal model of a thyristor. The thermal model simulation presents an error of 1.5 °C, while the FBG used allows for the determination of the thermal behavior and the field current dependence. Since the temperature is a function of the field current, the corresponding simulation can be used to estimate the temperature in the thyristors.

Fabricating Nanoporous Silica Structure on D-Fibres through Room Temperature Self-Assembly.

The room temperature deposition of self-assembling silica nanoparticles onto D-shaped optical fibres ("D-fibre"), drawn from milled preforms fabricated by modified chemical vapour deposition (MCVD), is studied. Vertical dip-and-withdraw produces tapered layers, with one end thicker (surface coverage >0.85) than the other, whilst horizontal dip-and-withdraw produces much more uniform layers over the core region. The propagation of induced fracturing over the core region during drying is overcome using a simple protrusion of the inner cladding. Thick coatings are discernible through thin film interference colouring, but thinner coatings require scanning electron microscopy (SEM) imaging. Here, we show that fluorescence imaging, using Rhodamine B, in this example, can provide some qualitative and speedy assessment of coverage.

Force monitoring in a maxilla model and dentition using optical fiber Bragg gratings.

The aim of this work is to show the possibility of using fiber optic sensors to instrument inside parts of an artificial maxilla and measure internal tension transmitted by the orthodontic and orthopedic appliances to the dentition and the adjacent bone. Bragg gratings written in a standard optical fiber were used to monitor the maxillary teeth and a multiplexed fiber was used to monitor the surface of the maxillary bone, transversally to the longest axis of the teeth. A Universal Test Machine was used to evaluate the sensitivity of the sensor to the vertical and lateral forces applied on the teeth. A wavelength shift of approximately 0.30 nm was detected when applying loads ranging from 0 to 20 N. By applying forces using the standard orthodontic appliances installed on the dentition it was possible to detect a range of forces between 0.025 N to 0.035 N during the activation of the arch wire and extra-oral forces. The use of the internal sensors in an artificial model made possible the monitoring of the resulting forces on the internal parts of the teeth and at the position where the strain takes place within the maxilla. The sensors detected that the orthodontic forces were not transmitted to the surface of the maxilla. This information is important to elucidate and to correlate undesirable effects as tooth root absorption and local pain during the orthodontic treatment.

Magnetic field measurements based on Terfenol coated photonic crystal fibers.

A magnetic field sensor based on the integration of a high birefringence photonic crystal fiber and a composite material made of Terfenol particles and an epoxy resin is proposed. An in-fiber modal interferometer is assembled by evenly exciting both eigenemodes of the HiBi fiber. Changes in the cavity length as well as the effective refractive index are induced by exposing the sensor head to magnetic fields. The magnetic field sensor has a sensitivity of 0.006 (nm/mT) over a range from 0 to 300 mT with a resolution about ±1 mT. A fiber Bragg grating magnetic field sensor is also fabricated and employed to characterize the response of Terfenol composite to the magnetic field.

Hydrostatic pressure sensing with high birefringence photonic crystal fibers.

The effect of hydrostatic pressure on the waveguiding properties of high birefringence photonic crystal fibers (HiBi PCF) is evaluated both numerically and experimentally. A fiber design presenting form birefringence induced by two enlarged holes in the innermost ring defining the fiber core is investigated. Numerical results show that modal sensitivity to the applied pressure depends on the diameters of the holes, and can be tailored by independently varying the sizes of the large or small holes. Numerical and experimental results are compared showing excellent agreement. A hydrostatic pressure sensor is proposed and demonstrated using an in-fiber modal interferometer where the two orthogonally polarized modes of a HiBi PCF generate fringes over the optical spectrum of a broad band source. From the analysis of experimental results, it is concluded that, in principle, an operating limit of 92 MPa in pressure could be achieved with 0.0003% of full scale resolution.

Evanescent-field spectroscopy using structured optical fibers: detection of charge-transfer at the porphyrin-silica interface.

The fabrication of porphyrin thin films derived from dichloro[5,10,15,20-tetra(heptyl)porphyrinato]tin(IV) [Cl-Sn(THP)-Cl] in the holes of photonic crystal fibers over 90 cm in length is described. Evanescent field spectroscopy (EFS) is used to investigate the interfacial properties of the films, with the high surface optical intensity and the long path length combining to produce significant absorption. By comparison with results obtained for similar films formed from Cl-Sn(THP)-Cl inside fused-silica cuvettes and on glass slides, the film is shown to be chemisorbed as a surface Si-O-Sn(THP)-X (X = Cl or OH) species. In addition to the usual porphyrin Q and Soret bands, new absorptions in the in-fiber films are observed by EFS at 445 nm and between 660-930 nm. The 660-930 nm band is interpreted as a porphyrin to silicon charge-transfer transition and postulated to arise following chemisorption at mechanical-strain induced defect sites on the silica surface. Such defect sites are caused by the optical fiber production process and are less prevalent on other glass surfaces. EFS within optical fibers therefore offers new ways for understanding interface phenomena such as surface adsorbates on glass. Such understanding will benefit all devices that exploit interface phenomena, both in optical fibers and other integrated waveguide forms. They may be directly exploited to create ultrasensitive molecular detectors and could yield novel photonic devices.

Micromachining structured optical fibers using focused ion beam milling.

A focused ion beam is used to mill side holes in air-silica structured fibers. By way of example, side holes are introduced in two types of air-structured fiber, (1) a photonic crystal four-ring fiber and (2) a six-hole single-ring step-index structured fiber.

Refractive Index Measurement within a Photonic Crystal Fibre Based on Short Wavelength Diffraction.

A new class of refractive index sensors using solid core photonic crystal fibres isdemonstrated. Coherent scattering at the cladding lattice is used to optically characterizematerials inserted into the fibre holes. The liquid to solid phase transition of water uponfreezing to ice 1h is characterized by determining the refractive index.

Fresnel Fibres with Omnidirectional Zone Cross-sections.

Fresnel fibres with silica zones resembling omnidirectional structures with self-imaging properties are proposed. Numerical simulation is carried out on a large air hole Fresnel fibre with a triadic Cantor fractal zone cross-section (FZC). The results show the transmission bandgap of these fibres widens and the practical confinement loss decreases with increasing orders of self-imaging. For an order of S = 4 a bandwidth Deltalambda= 0.69 mum and a confinement loss of 0.11 dB/km @ 1.1 mum is calculated.

Mapping the broadband polarization properties of linear 2D SOI photonic crystal waveguides.

Both quasi-TE and TM polarisation spectra for a silicon-on-insulator (SOI) waveguide are recorded over (1100-1700)nm using a broadband supercontinuum source. By studying both the input and output polarisation eigenstates we observe narrowband resonant cross coupling near the lowest quasi-TE mode cut-off. We also observe relatively broadband mixing between the two eigenstates to generate a complete photonic bandgap. By careful analysis of the output polarisation state we report on an inherent non-reciprocity between quasi TE and TM fundamental mode cross coupling. The nature of polarisation distinction in such bandgap structures is discussed in the context of polarisation scattering at an interface.

Bend loss in structured optical fibres.

Bend loss characterisation tests are carried out in two air-silica structured fibres: a periodic photonic crystal fibre and a non-periodic fibre. An explanation based on resonant coupling between interstitial zones accounts for the improved confinement of non-periodic structured optical fibres.

Water-soluble porphyrin detection in a pure-silica photonic crystal fiber.

Aqueous solutions of the water-soluble porphyrin 5,10,15,20-tetrakis(4-sulfonatophenyl)porphyrinatomanganese(III) acetate were inserted into the holes of a photonic crystal fiber, and the porphyrin absorption bands were identified. Results were obtained for three concentrations. The porphyrins in water show no surface interactions with the silica walls of the capillary channels. We discuss the implications for future hybrid electronic and photonic fiber devices.

Strain and temperature characterization of photonic crystal fiber Bragg gratings.

A Bragg grating in a photonic crystal fiber was written and its dependence with temperature and strain analyzed. The two observed Bragg wavelengths correspond to a fundamental and a higher-order mode in the optical fiber. The temperature and strain calibration curves for both modes are measured and found to be distinct. The general properties of gratings in these fibers, and their implications, are enunciated.

Water-core Fresnel fiber.

A water core photonic crystal Fresnel fiber exploiting a hole distribution on zone plates of a cylindrical waveguide was developed and characterized. This fiber has similar guiding properties as the pristine air-hole guiding fiber although a large loss edge ~900nm is observed indicating that the bandgap associated with Fresnel guidance has shifted to longer wavelengths. The absorption bands of the water in the region of the NIR were observed. The application to biosensing is discussed.