Mechanism of 1,4,5,8-naphthalene tetracarboxylic acid dianhydride hydrolysis and formation in aqueous solution.

The study of highly conjugated, carbonyl-containing molecules such as 1,4,5,8-naphthalene tetracarboxylic dianhydride, III, is of interest since reactivity differences and transmission of electronic effects through the conjugated framework can be evidenced. The kinetics of hydrolysis of III in aqueous solution were determined from 5 M acid to pH 10. In basic solution hydrolysis of III yields, sequentially, 1,4,5,8-naphthalene diacid monoanhydride, II, and 1,4,5,8-naphthalene tetracarboxylic acid, I. The second order rate constant for alkaline hydrolysis is 200 fold higher for the first ring opening. The water-catalyzed hydrolysis of III yields a pH-dependent mixture of ionic forms of I and II. The rate constant for water-catalyzed hydrolysis of III is 25 fold higher than that for II. In concentrated acid the rates for reaching equilibrium (I, II and III) increase and III is the major product. The pK(a)s of I (3.24, 5.13 and 6.25) and II (3.05, 5.90) were determined by potentiometric, fluorescence and UV spectroscopy titrations and by quantitative fit of the kinetic and equilibrium data. The apparent, pH-dependent, equilibrium constants, K(EqII), for anhydride formation between I and II were obtained from the UV spectra. The quantitative fit of kinetic and equilibrium data are consistent with the assumption that anhydride formation only proceeds with the fully protonated species for both I and II and permitted the estimation of the equilibrium constants for anhydride formation, K(EqII). The value of K(EqII) (I <==> II) between pH 1 and 6 was ca. 5. Geometry optimization calculations in the gas phase of the reactions of III in alkaline, neutral and acid conditions, at the DFT level of theory, gave electronic distributions that were qualitatively consistent with the experimental results.

Hybrid particles of polystyrene and carboxymethyl cellulose as substrates for copper ions.

The synthesis of hybrid particles was carried out by emulsion polymerization of styrene in complexes formed by carboxymethyl cellulose (CMC), a polyanion, and a cationic surfactant, cetyltrimethylammonium bromide (CTAB). CMC chains with variable molecular weights and degrees of substitution were tested. The polymerization condition chosen was that corresponding to CMC chains fully saturated with CTAB and to the onset of pure surfactant micelle formation, namely, at the critical aggregation concentration. The hybrid particles were characterized by zeta potential and light scattering measurements. The period of colloidal stability in the ionic strength of 2.0 mol L(-)(1) NaCl was observed visually. Upon increasing the CMC chain length, the particle characteristics remained practically unchanged, but the colloid stability was increased. The increase in the CMC degree of substitution led to particles with more negative zeta potential values. The adsorption of copper ions (Cu(2+)) on the surface of hybrid particles could be described by the Langmuir model, as determined by potentiometric measurements. The increase in the mean zeta potential values and X-ray absorption near-edge spectra evidenced the immobilization of Cu(2+) ions on the hybrid particles.

Spectrophotometric determination of acid volatile sulfide in river sediments by sequential injection analysis exploiting the methylene blue reaction.

This paper demonstrates the application of sequential injection analysis to perform sulfide determination using the methylene blue chemistry, based on two reagents: 3.63 mmol l(-1)N,N dimethyl-p-phenylene diamine hydrochloride in 1.1 mol l(-1) HCl solution and 19 mmol l(-1) FeCl(3), also in 1.1 mol l(-1) HCl. These solutions are aspirated inside the holding coil of the sequential injection system as two reagent zones sandwiching the sample zone. Under optimized conditions, the detection limit was calculated at 40 mug l(-1) S(2-), with a linear dynamic range from 0.05 to 2 mg l(-1) S(2-). This linear range can be extended up to 32 mg l(-1) using in-line dilution for sulfide concentrations greater than 2 mg l(-1). The robust characteristic of the SI system with syringe pump leads to very stable analytical curves (precision of 4%), minimizing the laborious preparation of sulfide standards. The method was applied in the determination of acid volatile sulfide in river sediments.

Determination of Cu, Pb, Cd, and Zn in river sediment extracts by sequential injection anodic stripping voltammetry with thin mercury film electrode.

Determination of Cu, Pb, Cd and Zn was performed in sediment extracts obtained according to the three steps sequential extraction procedure proposed by the European Community Standards, Measurements and Testing Program. The metal content was determined by anodic stripping voltammetry with a thin mercury film electrode controlled by a sequential injection (SIA) system. The proposed method improved the reproducibility of conventional anodic stripping voltammetry, as well as the sample throughput, allowing analysis of 30 to 45 samples per hour. The influence of flow rate and sample volume was studied to achieve an adequate sensitivity for the leachate studied. No interferences due to adsorption of organic matter, colloids, or complexes with slow rate of dissociation were observed. The intermetallic formation of Cu-Zn was avoided by forming the mercury film in presence of Ga(III) ions in the SIA system, resulting in low consumption of reagent in comparison to flow injection or continuous flow systems. Results were in good agreement with those obtained by Induced Coupled Plasma - Atomic Emission Spectroscopy (ICP-AES).

The use of linear potentiometric titration curves in the determination of alkalinity and acid-base properties of diluted solutions of humic substances.

A critical study of the use of Gran and modified Gran functions for the determination of alkalinity and acid-base properties of diluted solutions containing humic substances is presented. These solutions were composed of 340 muM HCO3(-)(3) in 0, 10, 20.5 and 41 mg/1. of sodium humate in order to simulate natural waters with different levels of dissolved organic carbon. The results showed that the alkalinity may be determined in good agreement with the expected value using both methodologies. The modified Gran functions give information about acid-base speciation in addition to the alkalinity. The application of the modified Gran functions for determination of humic acid pK(a)s and stoichiometry was studied under conditions simulating waters rich in natural organic matter in terms of humic acid concentrations.