Polyvinyl alcohol/chitosan wound dressings loaded with antiseptics.

Wound care remains a challenge in healthcare. This work aimed to develop a new polyvinyl alcohol (PVA)/chitosan (Ch) based wound dressing able to ensure protection, hydration and a controlled release of antiseptics, as alternative to actual treatments. Two distinct formulations (1:1 and 3:1, w/w) were prepared, sterilized by autoclaving and characterized concerning surface morphology, degradation over the time, mechanical properties and hydrophilicity. Both dressings revealed adequate properties for the intended purpose. The dressings were loaded with chlorhexidine (CHX) and polyhexanide (PHMB) and the drug release profiles were determined using Franz diffusion cells. The release of PHMB was more sustained than CHX, lasting for 2 days. As the amounts of drugs released by PVA/Ch 1:1 were greater, the biological tests were done only with this formulation. The drug loaded dressings revealed antibacterial activity against S. aureus and S. epidermidis, but only the ones loaded with PHMB showed adequate properties in terms of cytotoxicity and irritability. The application of this elastic dressing in the treatment of wounds in a dog led to faster recovery than conventional treatment, suggesting that the material can be a promising alternative in wound care.

Drug release from liposome coated hydrogels for soft contact lenses: the blinking and temperature effect.

In this article, liposome-based coatings aiming to control drug release from therapeutic soft contact lenses (SCLs) materials are analyzed. A PHEMA based hydrogel material loaded with levofloxacin is used as model system for this research. The coatings are formed by polyelectrolyte layers containing liposomes of 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC) and DMPC + cholesterol (DMPC + CHOL). The effect of friction and temperature on the drug release is investigated. The aim of the friction tests is to simulate the blinking of the eyelid in order to verify if the SCLs materials coated with liposomes are able to keep their properties, in particular the drug release ability. It was observed that under the study conditions, friction did not affect significantly the drug release from the liposome coated PHEMA material. In contrast, increasing the temperature of release leads to an increase of the drug diffusion rate through the hydrogel. This phenomenon is recorded both in the control and in the coated samples. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1799-1807, 2017.

Simulation of the hydrodynamic conditions of the eye to better reproduce the drug release from hydrogel contact lenses: experiments and modeling.

Currently, most in vitro drug release studies for ophthalmic applications are carried out in static sink conditions. Although this procedure is simple and useful to make comparative studies, it does not describe adequately the drug release kinetics in the eye, considering the small tear volume and flow rates found in vivo. In this work, a microfluidic cell was designed and used to mimic the continuous, volumetric flow rate of tear fluid and its low volume. The suitable operation of the cell, in terms of uniformity and symmetry of flux, was proved using a numerical model based in the Navier-Stokes and continuity equations. The release profile of a model system (a hydroxyethyl methacrylate-based hydrogel (HEMA/PVP) for soft contact lenses (SCLs) loaded with diclofenac) obtained with the microfluidic cell was compared with that obtained in static conditions, showing that the kinetics of release in dynamic conditions is slower. The application of the numerical model demonstrated that the designed cell can be used to simulate the drug release in the whole range of the human eye tear film volume and allowed to estimate the drug concentration in the volume of liquid in direct contact with the hydrogel. The knowledge of this concentration, which is significantly different from that measured in the experimental tests during the first hours of release, is critical to predict the toxicity of the drug release system and its in vivo efficacy. In conclusion, the use of the microfluidic cell in conjunction with the numerical model shall be a valuable tool to design and optimize new therapeutic drug-loaded SCLs.

About the effect of eye blinking on drug release from pHEMA-based hydrogels: an in vitro study.

The development of new ophthalmic drug delivery systems capable of increasing the residence time of drugs in the eye and improve its bioavailability relatively to eyedrops has been object of intense research in recent years. Several studies have shown that drug-loaded therapeutic soft contact lenses (SCLs) constitute a promising approach, with several potential advantages as compared with collyria. The main objective of this work is to study the effect of repetitive load and friction cycles caused by the eye blinking, on the drug release from hydrogels used in SCLs which, as far as we know, was never investigated before. Two poly-2-hydroxyethylmethacrylate-based hydrogels, pHEMA-T and pHEMA-UV, were used as model materials. Levofloxaxin was chosen as model drug. The hydrogels were fully characterized in what concerns structural and physicochemical properties. pHEMA-UV revealed some superficial porosity and a lower short-range order than pHEMA-T. We observe that the load and friction cycles enhanced the drug release from pHEMA-UV hydrogels. The application of a simple mathematical model, which takes into account the drug dilution caused by the tear flow, showed that the enhancement of the drug release caused by blinking on this hydrogel may be relevant in in vivo conditions. Conversely, the more sustained drug release from pHEMA-T is not affected by load and friction cycles. The conclusion is that, depending on the physicochemical and microstructural characteristics of the hydrogels, blinking is a factor that may affect the amount of drug delivered to the eye by SCLs and should thus be considered.