Assessment of the radionuclide remediation potential of novel miscanthus hybrids.

There are few studies related to the radionuclide remediation options, which comply to the demands of the environmentally non-destructive physical remediation methods. So far, most of the research was conducted on the phytoremediation capacity of different energy crops, as well as the established miscanthus hybrids which involved metal and heavy metal contaminants. Hence, the objective of this research was the radioecological characterization of the examined agroecosystem, including the initial source of the radionuclides (soil) as well as different miscanthus hybrids grown on the same soil. The results have shown that the radioactive content of soil was similar to the global averages. All measurements of the activity concentration of 137Cs in miscanthus samples were below the detection limits. There is also an indication that 210Pb is leaching into the lower layers (or is being taken up by miscanthus plant from the upper layers). Moreover, transfer factors (TFs) for radionuclides, as a more precise parameter for evaluating the phytoremediation potential, were calculated; the TFs were found to be very low for 226Ra (≤0.07), TFs for 40K (≤0.39) and for 232Th (≤0.21) were in the lower limits, whereas the TFs for 238U were found to be the highest (≤0.92). For 210Pb, the TFs were not calculated, since the expectation was that a significant part of the measured quantity came from the air, and not through the soil. Having in mind the sustainability and the circularity aspect of the radionuclide phytoremediation system, the appropriate management method should be applied for the disposal and utilization of the biomass contaminated with radionuclides. This research has shown that the radiological content in miscanthus is high enough and the ash content is low enough that miscanthus ash could be considered as a NORM (Naturally Occurring Radioactive Material), and it can be further used for the construction industry (i.e. concrete, tiles), in mixtures with other materials with certain limitations, similar to the utilization of ash from other sources such as coal or wood.

Natural Dyeing of Cellulose and Protein Fibers with the Flower Extract of Spartium junceum L. Plant.

In this study, the natural dye was extracted from Spartium junceum L. (SJL) flowers and applied on cellulose (cotton) and protein (wool) fabric. Fabrics were pre-mordant with alum prior to the dyeing process. Considering the global requirements on zero waste and green policy, the dyeing process was intended to be as much as possible environmentally friendly but still effective. Therefore, mordant concentration was optimized due to the reduction of the negative impact. The efficiency of the dyeing process was investigated by examination of fabrics' color characteristics and colorfastness to washing properties. In this paper, we have proved that the extracted dye from Spartium junceum L. is an acidic dye (mordant dye) which is more applicable for the treatment of wool fabrics. In this paper, it was proved that phytochemicals responsible for coloring are part of the flavonoids group. The UV absorption spectra of extracted dye show 4 bands in the region of λmax 224, 268, 308 and 346 nm which are ascribed to bands characteristic for flavonoids. Wool fabric pre-mordant with 3% alum and dyed shows great chromatic (C*) properties where C* value is in a range from 47.76 for unwashed samples to 47.50 for samples after 5 washing cycles and color hue (h°) is in a range 82.13 for unwashed samples to 81.52 for samples after 5 washing cycles. The best result regarding the colorfastness properties is shown by the wool sample treated with 3% alum after 5 washing cycles (total difference in color (Delta E*) = 0.87). These results confirm that metal (Al) from alum mordant make strong chemical bonds with wool substrate and dye since Delta E* values decrease in comparison to Delta E* values of the cotton samples treated the same way. The results revealed it is possible to reduce the concentration of mordant up to 3% and obtain satisfactory results regarding the colorfastness. Nevertheless, future research will go in the direction of replacing synthetic mordant with a more environmentally friendly one.

Progress in ethanol production from corn kernel by applying cooking pre-treatment.

In order to improve technological properties of corn kernel for ethanol production, samples were treated with a hydrothermal pre-treatment of cooking (steaming), prior to drying. Two types of cooking process parameters were applied; steam pressure of 0.5 bars during a 10 min period, and steam pressure of 1.5 bars during a 30 min period. Afterwards, samples were dried at four different temperatures, 70, 90, 110 and 130 degrees C. Control sample was also submitted to the aforementioned drying parameters. Since the results showed that starch utilization, due to the gelatinization process, was considerably higher in the samples pre-treated before the ethanol production process, it was found that the cooking treatment had a positive effect on ethanol yield from corn kernel. Therefore, the highest ethanol yield was found in the corn kernel samples cooked for 30 min at steam pressure 1.5 bars and dried at 130 degrees C. Due to the similarity of processes used for starch fermentation, introduction of cooking pre-treatment will not significantly increase the overall ethanol production costs, whereas it will result in significantly higher ethanol yield.