Characterization of Rabbit Corneas Subjected to Stromal Stiffening by the Açaí Extract (Euterpe oleracea).

PURPOSE: In this study, we characterized rabbit corneas subjected to corneal cross-linking (CXL) with açaí extract compared with a riboflavin photo-stimulated procedure. MATERIALS AND METHODS: The corneas of the slaughterhouse rabbits were divided into three groups: control, consisting of untreated corneal samples; riboflavin/UVA, where corneas were treated with 0.1% riboflavin photo-stimulated at 365 nm as the standard protocol; and açaí, where the samples were subjected to 4% açaí extract for 0.5-2 h. After the CXL procedure, corneas of the three groups were characterized by analyzing their elastic modulus and thermal denaturation profile. RESULTS: The elastic modulus at 3% strain showed an approximately threefold increase in the riboflavin/UVA group and 10.5 times in the corneas treated with 4% açaí extract for 2 h, compared with the control group (p < 0.01). The denaturation temperature values of the two groups of crosslinked corneas increased significantly (p < 0.05) and were more pronounced in the açaí group. CONCLUSIONS: The açaí extract was effective in promoting CXL in rabbit corneas as characterized by the different techniques.

Fast analysis of terbutaline in pharmaceuticals using multi-walled nanotubes modified electrodes from recordable compact disc.

In this study, homemade disposable gold electrodes made from recordable compact disks were modified with carbon nanotubes for amperometric quantification of terbutaline sulfate in pharmaceutical products. A flow cell using an impingent jet of solution on the electrode surface was build and used for amperometric detection, and a series of experiments were carried out to find the best experimental conditions for the new electrode in a specially designed cell. A linear response for terbutaline was obtained in the range from 3.0 × 10(-6) to 5.0 × 10(-4) mol L(-1) (at 0.63 V vs. Ag/AgCl). The limits of detection and quantification were calculated as 5.8 × 10(-7) mol L(-1) (S/N = 3) and 1.9 × 10(-6) mol L(-1) (S/N = 10), respectively. A frequency of 30 injections h(-1) was attained. The proposed method was successfully applied to the analyses of commercial syrup samples, and all results were in good agreement with those obtained by using high performance liquid chromatography and capillary electrophoresis-tandem mass spectrometry.

Pressure and temperature effects on intermolecular vibrational dynamics of ionic liquids.

Low frequency Raman spectra of ionic liquids have been obtained as a function of pressure up to ca. 4.0 GPa at room temperature and as a function of temperature along the supercooled liquid and glassy state at atmospheric pressure. Intermolecular vibrations are observed at ~20, ~70, and ~100 cm(-1) at room temperature in ionic liquids based on 1-alkyl-3-methylimidazolium cations. The component at ~100 cm(-1) is assigned to librational motion of the imidazolium ring because it is absent in non-aromatic ionic liquids. There is a correspondence between the position of intermolecular vibrational modes in the normal liquid state and the spectral features that the Raman spectra exhibit after partial crystallization of samples at low temperatures or high pressures. The pressure-induced frequency shift of the librational mode is larger than the other two components that exhibit similar frequency shifts. The lowest frequency vibration observed in a glassy state corresponds to the boson peak observed in light and neutron scattering spectra of glass-formers. The frequency of the boson peak is not dependent on the length scale of polar∕non-polar heterogeneity of ionic liquids, it depends instead on the strength of anion-cation interaction. As long as the boson peak is assigned to a mixing between localized modes and transverse acoustic excitations of high wavevectors, it is proposed that the other component observed in Raman spectra of ionic liquids has a partial character of longitudinal acoustic excitations.

Thermal analysis and Raman spectra of different phases of the ionic liquid butyltrimethylammonium bis(trifluoromethylsulfonyl)imide.

The ionic liquid butyltrimethylammonium bis(trifluoromethylsulfonyl)imide, [C(4)C(1)C(1)C(1)N][Tf(2)N], is a glass-forming liquid that exhibits partial crystallization depending on the cooling rate. Differential scanning calorimetry (DSC) indicates crystallization at T(c) = 227 K, melting at T(m) = 258 K, glass transition at T(g) ~ 191 K, and also cold crystallization at T(cc) ~ 219 K. Raman spectroscopy shows that the crystalline structure obtained by slow cooling is formed with [Tf(2)N](-) in cisoid conformation, whereas [Tf(2)N](-) in transoid conformation results from fast cooling. No preferred conformation of the butyl chain of the [C(4)C(1)C(1)C(1)N](+) cation is favored by slow or fast cooling of [C(4)C(1)C(1)C(1)N][Tf(2)N]. Low-frequency Raman spectroscopy shows that crystalline domains developing in the supercooled liquid result in a glacial state made of a mixture of crystallites and amorphous phase. However, these crystalline structures obtained by slow cooling or cold crystallization are not the same because anion-cation interactions promote local structures with distinct conformations of the [Tf(2)N](-) anion.

Immunological parameters related to the adjuvant effect of the ordered mesoporous silica SBA-15.

In 2006, the first report of a nanostructured material as adjuvant was described establishing the effectiveness of the ordered mesoporous SBA-15 silica as an immune adjuvant. The present study evaluated the SBA-15 capacity to modulate the immune responsiveness of High and Low responder mice immunized with BSA encapsulated/adsorbed in SBA-15 by the intramuscular or oral route and the adjuvant effect was compared with the responsiveness induced by BSA in aluminum hydroxide salts or emulsified in Incomplete Freund adjuvant. These results demonstrate the ability of the non-toxic SBA-15 nanoparticles to increase the immunogenicity and repair the responsiveness of the constitutively low responder individuals inducing both the IgG2a and the IgG1 isotypes, independently of the immune cell committed and conditioning the low phenotype. This new adjuvant may reveal novel therapeutic targets for immune modulation and vaccine design.

Effect of experimental heat treatment on mechanical properties of resin composites.

The aim of this study was to verify the influence of an experimental heat treatment (170 masculineC/10 min) using a casting furnace on the mechanical properties (hardness and flexural strength) of 2 commercial direct resin composites (TPH Spectrum and Filtek P60) compared to a commercial indirect resin system (BelleGlass). Heat treatment temperature was determined after thermal characterization by thermogravimetry (TG) and differential scanning calorimetry (DSC). Data was analyzed by ANOVA and Tukey's test at 5% significance level. There was statistical significance for the main factor heat treatment (p=0.03) and composite (p=0.02), for flexural strength. For Knoop hardness, only the main factor composite was statistically significant (p=0.00). P60 presented higher hardness than TPH. No statistically significant correlation between mechanical properties tested was detected. Based on these results, it was possible to conclude that heat treatment influenced flexural strength of direct composites, while it was not observed for hardness. The association of direct composites with a simple post-cure heat treatment may be an alternative for current indirect composite systems, although more studies are needed to verify other properties of the composites for this application.

Effect of experimental heat treatment on mechanical properties of resin composites

The aim of this study was to verify the influence of an experimental heat treatment (170ºC/10 min) using a casting furnace on the mechanical properties (hardness and flexural strength) of 2 commercial direct resin composites (TPH Spectrum and Filtek P60) compared to a commercial indirect resin system (BelleGlass). Heat treatment temperature was determined after thermal characterization by thermogravimetry (TG) and differential scanning calorimetry (DSC). Data was analyzed by ANOVA and Tukey's test at 5 percent significance level. There was statistical significance for the main factor heat treatment (p=0.03) and composite (p=0.02), for flexural strength. For Knoop hardness, only the main factor composite was statistically significant (p=0.00). P60 presented higher hardness than TPH. No statistically significant correlation between mechanical properties tested was detected. Based on these results, it was possible to conclude that heat treatment influenced flexural strength of direct composites, while it was not observed for hardness. The association of direct composites with a simple post-cure heat treatment may be an alternative for current indirect composite systems, although more studies are needed to verify other properties of the composites for this application.

O objetivo deste estudo foi avaliar a influência de um tratamento térmico experimental (170ºC/10 min), em um forno de fundição, sobre as propriedades mecânicas (dureza e resistência à flexão) de 2 resinas compostas comerciais de uso direto (TPH Spectrum e Filtek P60), em relação a uma resina comercial indireta (BelleGlass). A temperatura de tratamento térmico foi determinada após caracterização térmica por termogravimetria (TG) e calorimetria exploratória diferencial (DSC). Os dados foram analisados por análise de variância, que mostrou, para a resistência à flexão, diferença estatística para os fatores principais tratamento térmico (p=0,03) e material (p=0,02). Para a dureza Knoop, somente o fator principal material foi estatisticamente significante (p=0,00). A P60 apresentou maiores valores de dureza em relação à TPH Spectrum. Não foi detectada nenhuma correlação estatisticamente significante entre as propriedades mecânicas avaliadas. Baseado nos resultados foi possível concluir que o tratamento térmico influenciou na resistência à flexão das resinas compostas de uso direto, enquanto, para a dureza, o mesmo não foi observado. A associação de resinas compostas a um simples tratamento térmico de pós-cura pode ser uma alternativa para os sistemas indiretos atuais. Entretanto, mais estudos são necessários para verificar outras propriedades das resinas compostas para esta aplicação.

Effect of extract of Phyllanthus niruri on crystal deposition in experimental urolithiasis.

Phyllanthus niruri (Pn) is a plant that has been shown to interfere in the growth and aggregation of calcium oxalate (CaOx) crystals. In the present study we evaluated the effect of Pn on the preformed calculus induced by introduction of a CaOx seed into the bladder of male Wistar rats. Pn treatment (5 mg/ rat/day) was initiated immediately or 30 days after CaOx seeding and thus in the presence of a preformed calculus. Animals were sacrificed 50 or 70 days after surgery. The resulting calculi were weighed and analyzed by X-ray diffraction, stereomicroscopy and scanning electronic microscopy. Precocious Pn treatment reduced the number (75%, P < 0.05) and the weight (65%, P < 0.05) of calculi that frequently exhibited a matrix-like material on its surface, compared to the untreated CaOx group. In contrast, Pn treatment in the presence of a preformed calculus did not prevent further calculus growth; rather, it caused an impressive modification in its appearance and texture. Calculi from Pn-treated animals had a smoother, homogeneous surface compared to the spicule shape of calculi found in the untreated CaOx group. XRD analysis revealed the precipitation of struvite crystals over the CaOx seed and Pn did not change the crystalline composition of the calculi. This suggests that Pn interfered with the arrangement of the precipitating crystals, probably by modifying the crystal-crystal and/or crystal-matrix interactions. Results suggest that Pn may have a therapeutic potential, since it was able to modify the shape and texture of calculi to a smoother and probably more fragile form, which could contribute to elimination and/or dissolution of calculi.

Comparative thermogravimetric and adsorption study of highly ordered mesoporous materials.

A comparative study was carried out for highly ordered mesoporous materials using high resolution thermogravimetry (HR-TG) and adsorption techniques. These materials were synthesized with mixed surfactants of various alkyl chain lengths. For thermogravimetry measurements n-butanol was used to probe the adsorbent surface and high-resolution TG curves as well as their 1st and 2nd derivatives were obtained for this probe molecule. It is shown that the values of the mesopore volume and specific surface area evaluated from TG data are in a good agreement with those evaluated from low-temperature nitrogen adsorption isotherms. This comparative study was performed to confirm the usefulness of the HR-TG technique as an alternative method for evaluation of the mesopore volume and specific surface area of ordered mesoporous materials.

Synthesis of FDU-1 silica with narrow pore size distribution and tailorable pore entrance size in the presence of sodium chloride.

Ordered silicas with large (9-15 nm), uniform, cagelike mesopores were synthesized under acidic aqueous conditions from tetraethyl orthosilicate in the presence of sodium chloride using poly(ethylene oxide)-poly(butylene oxide)-poly(ethylene oxide) triblock copolymer B50-6600 (EO39BO47EO39, Dow Chemicals) as a supramolecular template. Except for the use of NaCl in our case, the synthesis mixture composition was the same as that originally reported by Zhao et al. for the synthesis of FDU-1 silica, which was later shown to exhibit a cubic close-packed (Fm3m) structure with stacking faults related to the occurrence of hexagonal close-packed stacking sequences. The copolymer-templated silicas were formed at room temperature and in most cases were subjected to the hydrothermal treatment at 373 or 393 K. The calcined materials were characterized using small-angle X-ray scattering (SAXS) and nitrogen and argon adsorption at 77 K. SAXS patterns were generally similar to those reported for FDU-1 silica, indicating the cubic close-packed (Fm3m) structure, but the presence of stacking faults characteristic of a hexagonal close-packed structure cannot be precluded. The addition of the salt was found to significantly narrow the pore size distributions and to improve the uniformity of entrances to the cagelike mesopores, whereas the pore diameter, specific surface area, and pore volume were similar (in most cases slightly lower) to those for FDU-1 silicas obtained in the absence of NaCl. The materials synthesized in the presence of NaCl also appeared to have better resolved SAXS patterns. The feasibility of tailoring the pore cage diameter (from approximately 9.5 to 14.5 nm) and pore entrance diameter (from below 4 to approximately 8 nm) simply by adjusting the hydrothermal treatment temperature and time was demonstrated, indicating that these simple and convenient ways of structural design of cagelike mesopores are operative in the case of syntheses in the presence of inorganic salts.