Multitask Imidazolium Salt Additives for Innovative Poly(l-lactide) Biomaterials: Morphology Control, Candida spp. Biofilm Inhibition, Human Mesenchymal Stem Cell Biocompatibility, and Skin Tolerance.

Candida species have great ability to colonize and form biofilms on medical devices, causing infections in human hosts. In this study, poly(l-lactide) films with different imidazolium salt (1-n-hexadecyl-3-methylimidazolium chloride (C16MImCl) and 1-n-hexadecyl-3-methylimidazolium methanesulfonate (C16MImMeS)) contents were prepared, using the solvent casting process. Poly(l-lactide)-imidazolium salt films were obtained with different surface morphologies (spherical and directional), and the presence of the imidazolium salt in the surface was confirmed. These films with different concentrations of the imidazolium salts C16MImCl and C16MImMeS presented antibiofilm activity against isolates of Candida tropicalis, Candida parapsilosis, and Candida albicans. The minor antibiofilm concentration assay enabled one to determine that an increasing imidazolium salt content promoted, in general, an increase in the inhibition percentage of biofilm formation. Scanning electron microscopy micrographs confirmed the effective prevention of biofilm formation on the imidazolium salt containing biomaterials. Lower concentrations of the imidazolium salts showed no cytotoxicity, and the poly(l-lactide)-imidazolium salt films presented good cell adhesion and proliferation percentages with human mesenchymal stem cells. Furthermore, no acute microscopic lesions were identified in the histopathological evaluation after contact between the films and pig ear skin. In combination with the good morphological, physicochemical, and mechanical properties, these poly(l-lactide)-based materials with imidazolium salt additives can be considered as promising biomaterials for use in the manufacturing of medical devices.

Influence of light-activation protocol on methacrylate resin-composite evaluated by dynamic mechanical analysis and degree of conversion.

The aim of this study was to evaluate the degree of conversion (DC) and to identify the viscoelastic properties: storage modulus (E'), loss modulus (E"), tangent delta (tan δ), and glass transition temperature (T g ) of a microhybrid resin-composite light-activated by three different protocols. A Filtek Z250 (3 M ESPE) shade A3 was inserted in a Teflon mold (21 mm × 5 mm × 1 mm for viscoelastic properties; and 5 mm × 1 mm for DC) and light-activated according to the following light-activation protocols: (S) 1,000 mW/cm(2) × 19 s, (HP) 1,400 mW/cm(2) × 14 s, and (PE) 3,200 mW/cm(2) × 6 s, all set up to deliver 19 J/cm(2). Viscoelastic properties was assessed by dynamic mechanical analysis (DMA) (n = 3), performed in single cantilever clamped mode. DC (n = 5) was measured by FTIR on top (T) and bottom (B) surfaces, and the data was submitted to a split-plot one-way ANOVA. For DC, there was a significant effect for surface factor and light-activation protocols factor. Top surface showed higher DC than B in all experimental conditions. Light-activation protocols S and HP resulted in higher DC than PE and were similar between them. Viscoelastic properties (E', E", tan δ, T g ) were not affected by light-activation protocols. It could be concluded that light-activation protocols influenced DC but not influenced the viscoelastic properties.

Morphological and structural characterization of PHBV/organoclay nanocomposites by small angle X-ray scattering.

In this work, the morphological and structural behaviors of poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) nanocomposites were investigated using small angle X-ray scattering (SAXS), wide angle X-ray diffraction (WAXD) and transmission electron microscopy (TEM). The nanocomposites with 1, 3 and 5 wt.% of organically modified montmorillonite Cloisite® 30B (OMMT) were prepared by melt processing in a twin screw extruder using two different processing conditions (low and high shear intensity). The lamellar long period of the polymer was lower for the nanocomposites, with high polydispersity values. However, the crystalline thickness increased with the clay content and was independent of the processing conditions. This behavior resulted in a high linear crystallinity of the nanocomposites with 3 and 5 wt.% OMMT. The disruption factor (ß) was in agreement with the WAXD and TEM findings, indicating a good dispersion of the nanoparticles in the PHBV matrix with 3 wt.% of OMMT during the high shear intensity of melt processing.