Incorporation of casein phosphopeptide-amorphous calcium phosphate into a glass-ionomer cement.

Casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) nanocomplexes have been shown to prevent demineralization and promote remineralization of enamel subsurface lesions in animal and in situ caries models. The aim of this study was to determine the effect of incorporating CPP-ACP into a self-cured glass-ionomer cement (GIC). Incorporation of 1.56% w/w CPP-ACP into the GIC significantly increased microtensile bond strength (33%) and compressive strength (23%) and significantly enhanced the release of calcium, phosphate, and fluoride ions at neutral and acidic pH. MALDI mass spectrometry also showed casein phosphopeptides from the CPP-ACP nanocomplexes to be released. The release of CPP-ACP and fluoride from the CPP-ACP-containing GIC was associated with enhanced protection of the adjacent dentin during acid challenge in vitro.

Long-term quantification of the release of monomers from dental resin composites and a resin-modified glass ionomer cement.

This study quantified the release of monomers from polymerized specimens of four commercially available resin composites and one glass ionomer cement immersed in water:ethanol solutions. Individual standard curves were prepared from five monomers: (1) triethylene glycol dimethacrylate (TEGDMA), (2) 2-hydroxy-ethyl methacrylate (HEMA), (3) urethane dimethacrylate (UDMA), (4) bisphenol A glycidyl dimethacrylate (BISGMA), and (5) bisphenol A. The concentration of the monomers was determined at Days 1, 7, 30, and 90 with the use of electrospray ionization/mass spectrometry. Data were expressed in mean micromol per mm(2) surface area of specimen and analyzed with Scheffe's test (p<0.05). The following monomers were found in water: monomers (1) and (2) from Delton sealant, monomer (5) from ScotchBond Multipurpose Adhesive and Delton sealant, monomer (3) from Definite and monomer (4) from Fuji II LC, ScotchBond Multipurpose Adhesive, Synergy and Definite. All these monomers increased in concentration over time, with the exception of monomer (1) from Delton sealant. Monomers (3) and (5) were found in extracts of materials despite their absence from the manufacturer's published composition. All monomers were released in significantly higher concentrations in water:ethanol solutions than in water. The greatest release of monomers occurred in the first day. The effect of the measured concentrations of monomers (1-5) on human genes, cells, or tissues needs to be considered with the use of a biological model.

Fluoride release from glass ionomer cements and resin composites coated with a dentin adhesive.

OBJECTIVES: This laboratory study compared the effect of surface coatings on patterns and amounts of fluoride released from four glass ionomer cements and two fluoride-containing resin composites. METHODS: Twelve cylinders of each material were prepared in a polyethylene mold. The experimental groups (n = 6) were coated with one layer of an adhesive resin (3M Scotchbond Multipurpose Adhesive), while the control groups (n = 6) remained uncoated. Cumulative fluoride release into deionized water was measured on days 1, 2, 3, 7, 14, 21 and 28 using an ion analyzer. Total fluoride release after 28 days was analyzed for significant differences among materials using one-way ANOVA and Student-Newman-Keuls test (p < 0.05). RESULTS: The total amounts of fluoride release from the coated samples were found to be significantly less than the uncoated samples for all materials, except Solitaire. The uncoated samples released a total amount of fluoride of between 2.3 and 85.4 ppm, while the coated samples released a total amount of fluoride of between < 0.2 and 24.1 ppm. Similar patterns of fluoride release were found in coated and uncoated samples. SIGNIFICANCE: The results indicated that the application of a dentin adhesive coating did not completely prevent fluoride release from glass ionomer cements and fluoridated resin composites, although the amounts were significantly less. Clinically, it suggests that a continued release of fluoride from glass ionomer cements and fluoridated resin composites is possible after placing a thin layer of resin adhesive. The clinical significance of these findings is not known.