High-magnification Faraday rotation imaging and analysis of X-pinch implosion dynamics.

An X-pinch load driven by an intense current pulse (>100 kA in ∼100 ns) can result in the formation of a small radius, runaway compressional micro-pinch. A micro-pinch is characterized by a hot (>1 keV), current-driven (>100 kA), high-density plasma column (near solid density) with a small neck diameter (1-10 µm), a short axial extent (<1 mm), and a short duration (≲1 ns). With material pressures often well into the multi-Mbar regime, a micro-pinch plasma often radiates an intense, sub-ns burst of sub-keV to multi-keV x rays. A low-density coronal plasma immediately surrounding the dense plasma neck could potentially shunt current away from the neck and thus reduce the magnetic drive pressure applied to the neck. To study the current distribution in the coronal plasma, a Faraday rotation imaging diagnostic (1064 nm) capable of producing simultaneous high-magnification polarimetric and interferometric images has been developed for the MAIZE facility at the University of Michigan. Designed with a variable magnification (1-10×), this diagnostic achieves a spatial resolution of ∼35 µm, which is useful for resolving the ∼100-µm-scale coronal plasma immediately surrounding the dense core. This system has now been used on a reduced-output MAIZE (100-200 kA, 150 ns) to assess the radial distribution of drive current immediately surrounding the dense micro-pinch neck. The total current enclosed was found to increase as a function of radius, r, from a value of ≈50±25 kA at r ≈ 140 µm (at the edge of the dense neck) to a maximal value of ≈150±75 kA for r ≥ 225 µm. This corresponds to a peak magnetic drive pressure of ≈75±50 kbar at r ≈ 225 µm. The limitations of these measurements are discussed in the paper.

Additively manufactured electrodes for plasma and power-flow studies in high-power transmission lines on the 1-MA MAIZE facility.

Power-flow studies on the 30-MA, 100-ns Z facility at Sandia National Laboratories have shown that plasmas in the facility's magnetically insulated transmission lines (MITLs) and double post-hole convolute can result in a loss of current delivered to the load. To study power-flow physics on the 1-MA, 100-ns MAIZE facility at the University of Michigan, planar MITL loads and planar post-hole convolute loads have been developed that extend into the lines of sight for various imaging diagnostics on MAIZE. These loads use 3D-printed dielectric support structures lined with thin foils of either aluminum or stainless steel. The metal foils serve as the current-carrying power-flow surfaces, which generate plasma during the current pulse. The foil thickness (50 µm) and widths (11.5-16 mm) are selected to ensure a sufficient linear current density (0.5-0.7 MA/cm) for plasma formation. Laser backlighting (532 nm) and visible-light self-emission imaging capture the overall plasma evolution in the anode-cathode gaps, including the gap closure velocities (1-4 cm/µs).

Stabilization of Liner Implosions via a Dynamic Screw Pinch.

Magnetically driven implosions are susceptible to magnetohydrodynamic instabilities, including the magneto-Rayleigh-Taylor instability (MRTI). To reduce MRTI growth in solid-metal liner implosions, the use of a dynamic screw pinch (DSP) has been proposed [P. F. Schmit et al., Phys. Rev. Lett. 117, 205001 (2016)PRLTAO0031-900710.1103/PhysRevLett.117.205001]. In a DSP configuration, a helical return-current structure surrounds the liner, resulting in a helical magnetic field that drives the implosion. Here, we present the first experimental tests of a solid-metal liner implosion driven by a DSP. Using the 1-MA, 100-200-ns COBRA pulsed-power driver, we tested three DSP cases (with peak axial magnetic fields of 2 T, 14 T, and 20 T) and a standard z-pinch (SZP) case (with a straight return-current structure and thus zero axial field). The liners had an initial radius of 3.2 mm and were made from 650-nm-thick aluminum foil. Images collected during the experiments reveal that helical MRTI modes developed in the DSP cases, while nonhelical (azimuthally symmetric) MRTI modes developed in the SZP case. Additionally, the MRTI amplitudes for the 14-T and 20-T DSP cases were smaller than in the SZP case. Specifically, when the liner had imploded to half of its initial radius, the MRTI amplitudes for the SZP case and for the 14-T and 20-T DSP cases were, respectively, 1.1±0.3 mm, 0.7±0.2 mm, and 0.3±0.1 mm. Relative to the SZP, the stabilization obtained using the DSP agrees reasonably well with theoretical estimates.

A pulsed-power implementation of "Laser Gate" for increasing laser energy coupling and fusion yield in magnetized liner inertial fusion (MagLIF).

Magnetized Liner Inertial Fusion (MagLIF) at Sandia National Laboratories involves a laser preheating stage where a few-ns laser pulse passes through a few-micron-thick plastic window to preheat gaseous fusion fuel contained within the MagLIF target. Interactions with this window reduce heating efficiency and mix window and target materials into the fuel. A recently proposed idea called "Laser Gate" involves removing the window well before the preheating laser is applied. In this article, we present experimental proof-of-principle results for a pulsed-power implementation of Laser Gate, where a thin current-carrying wire weakens the perimeter of the window, allowing the fuel pressure to push the window open and away from the preheating laser path. For this effort, transparent targets were fabricated and a test facility capable of studying this version of Laser Gate was developed. A 12-frame bright-field laser schlieren/shadowgraphy imaging system captured the window opening dynamics on microsecond timescales. The images reveal that the window remains largely intact as it opens and detaches from the target. A column of escaping pressurized gas appears to prevent the detached window from inadvertently moving into the preheating laser path.

Optimization of switch diagnostics on the MAIZE linear transformer driver.

The MAIZE Linear Transformer Driver consists of 40 capacitor-switch-capacitor "bricks" connected in parallel. When these 40 bricks are charged to ±100-kV and then discharged synchronously, the MAIZE facility generates a 1-MA current pulse with a 100-ns rise time into a matched load impedance. Discharging each of the capacitors in a brick is carried out by the breakdown of a spark-gap switch, a process that results in the emission of light. Monitoring this output light with a fiber optic coupled to a photomultiplier tube (PMT) and an oscilloscope channel provides information on switch performance and timing jitter-whether a switch fired early, late, or in phase with the other switches. However, monitoring each switch with a dedicated detector-oscilloscope channel can be problematic for facilities where the number of switches to be monitored (e.g., 40 on MAIZE) greatly exceeds the number of detector-oscilloscope channels available. The technique of using fibers to monitor light emission from switches can be optimized by treating a PMT as a binary digit or bit and using a combinatorial encoding scheme, where each switch is monitored by a unique combination of fiber-PMT-oscilloscope channels simultaneously. By observing the unique combination of fiber-PMT-oscilloscope channels that are turned on, the prefiring or late-firing of a single switch on MAIZE can be identified by as few as six PMT-oscilloscope channels. The number of PMT-oscilloscope channels, N, required to monitor X switches can be calculated by 2N = X + 1, where the number "2" is selected because the PMT-oscilloscope acts as a bit. In this paper, we demonstrate the use of this diagnostic technique on MAIZE. We also present an analysis of how this technique could be scaled to monitor the tens of thousands of switches proposed for various next generation pulsed power facilities.

Perioperative assessment of older surgical patients using a frailty index-feasibility and association with adverse post-operative outcomes.

This study aimed to examine the feasibility of using a frailty index (FI) based on comprehensive geriatric assessment (CGA), to assess the level of frailty in older surgical patients preoperatively and to evaluate the association of FI-CGA with poorer postoperative outcomes. Two hundred and forty-six patients aged ≥70 years undergoing intermediate- to high-risk surgery in a tertiary hospital were recruited. Frailty was assessed using a 57-item FI-CGA form, with fit, intermediate frail, and frail patients defined as FI ≤0.25, >0.25 to 0.4, and >0.4, respectively. Adverse outcomes were ascertained at 30 days and 12 months post-surgery. Logistic regression models assessed the relationship between FI and adverse outcomes, adjusting for age, gender and acuity of surgery. The mean age of the participants was 79 years (standard deviation [SD] 6.5%), 52% were female, 91% were admitted from the community, 43% underwent acute surgery, and 19% were assessed as frail. The FI-CGA form was reported as being easy to apply, with a low patient refusal rate (2.2%). The majority of items were easy to rate, although inter-rater reliability was not tested. In relation to outcomes, greater frailty was associated with increased 12-month mortality (6.4%, 15.6%, and 23% for fit, intermediate frail, and frail patients respectively, P=0.01) and 12-month hospital readmissions (33.9%, 48.9%, and 60% respectively, P=0.004). There were no statistically significant differences between fit, intermediate frail, and frail groups in perioperative adverse events (17.4%, 23.3%, and 19.1% respectively, P=0.577) or 30-day postoperative complications (35.8%, 47.8%, and 46.8% respectively, P=0.183). Our findings suggest that it is feasible to use the FI-CGA to assess frailty preoperatively, and that using the FI-CGA may identify patients at high risk of adverse long-term outcomes.

A 7.2 keV spherical x-ray crystal backlighter for two-frame, two-color backlighting at Sandia's Z Pulsed Power Facility.

Many experiments on Sandia National Laboratories' Z Pulsed Power Facility-a 30 MA, 100 ns rise-time, pulsed-power driver-use a monochromatic quartz crystal backlighter system at 1.865 keV (Si Heα) or 6.151 keV (Mn Heα) x-ray energy to radiograph an imploding liner (cylindrical tube) or wire array z-pinch. The x-ray source is generated by the Z-Beamlet laser, which provides two 527-nm, 1 kJ, 1-ns laser pulses. Radiographs of imploding, thick-walled beryllium liners at convergence ratios CR above 15 [CR=ri(0)/ri(t)] using the 6.151-keV backlighter system were too opaque to identify the inner radius ri of the liner with high confidence, demonstrating the need for a higher-energy x-ray radiography system. Here, we present a 7.242 keV backlighter system using a Ge(335) spherical crystal with the Co Heα resonance line. This system operates at a similar Bragg angle as the existing 1.865 keV and 6.151 keV backlighters, enhancing our capabilities for two-color, two-frame radiography without modifying the system integration at Z. The first data taken at Z include 6.2-keV and 7.2-keV two-color radiographs as well as radiographs of low-convergence (CR about 4-5), high-areal-density liner implosions.

Goosefish Lophius americanus fecundity and spawning frequency, with implications for population reproductive potential.

To improve knowledge of goosefish Lophius americanus' reproductive biology, females were collected during 2009-2012 from the Mid-Atlantic Bight shelf region of the U.S. east coast. Batch fecundity increased with total length (LT ), from 229 100 to 2 243 300 mature oocytes per female (LT range: 55·5-112 cm; n = 54). This estimate of fecundity at LT is lower than one derived from a sample collected during 1982-1985. Examination of whole oocyte diameters in different months indicated that L. americanus is a serial spawner, releasing more than one egg veil per spawning season, as suspected or observed for other Lophius species. Seasonality of spawning was evident from whole oocytes and gonad histology, and from larval fish surveys spanning the U.S. north-east shelf, and confirmed a protracted (c. 6 months) spawning period. Peak spawning activity progressed northward from spring to autumn. The population-level implications of these results were explored by estimating population reproductive potential (PRP ), which considered the value of both current and future per capita reproduction using decade-specific age structure and fecundity at length. PRP is now more than 50% lower compared with the historical period (1982-1985), a result of the lower proportions of large females and reduced fecundity across all sizes. Mechanisms that could explain this loss of stock productivity are fishing-induced size-age truncation or regime shifts in egg production caused by changes in energy density of common forage species.

A new time and space resolved transmission spectrometer for research in inertial confinement fusion and radiation source development.

We describe the design and function of a new time and space resolved x-ray spectrometer for use in Z-pinch inertial confinement fusion and radiation source development experiments. The spectrometer is designed to measure x-rays in the range of 0.5-1.5 Å (8-25 keV) with a spectral resolution λ/Δλ ∼ 400. The purpose of this spectrometer is to measure the time- and one-dimensional space-dependent electron temperature and density during stagnation. These relatively high photon energies are required to escape the dense plasma created at stagnation and to obtain sensitivity to electron temperatures ≳3 keV. The spectrometer is of the Cauchois type, employing a large 30 × 36 mm2, transmissive quartz optic for which a novel solid beryllium holder was designed. The performance of the crystal was verified using offline tests, and the integrated system was tested using experiments on the Z pulsed power accelerator.

Immune Cell Infiltration in Feline Meningioma.

Meningioma is the most common primary brain tumour in the cat. Although most of these tumours are considered to be benign based on histological characteristics, little is known regarding microenvironmental changes associated with the tumour. The characterization of the immune-cell infiltrate in human and canine meningiomas has been described; however, there are no data regarding the cat equivalent. Seventeen formalin-fixed, paraffin wax-embedded samples of feline meningioma were evaluated by light microscopy and immunohistochemistry (IHC) for expression of CD3, Pax5, Iba-1, HLA-DR, MAC387, CD163 and Ki67. Variable immune cell infiltrates were seen in every case. All tumours had moderate numbers of infiltrating CD3+ T lymphocytes. Seven of 17 tumours (41%) had infiltrating PAX5+ B lymphocytes that were often dispersed randomly throughout the neoplasm. Macrophage infiltration was abundant in all tumours with widespread immunoreactivity for Iba-1 and HLA-DR. Most tumours (15/17; 88%) had infiltration by MAC387+ macrophages; however, the number of infiltrating cells per ×400 field varied widely (from 0 to 57). Thirteen of 17 tumours (76%) had infiltration by CD163+ macrophages; however (similar to the MAC387 IHC), several tumours had numerous infiltrating cells. There was a potential weak negative rank correlation between the counts of CD3 and Ki67+ cells (rSp = -0.57; P = 0.018); however, no other rank correlations could be established between types of infiltrating immune cells (all other P ≥0.10). This study establishes evidence for a robust population of immune cells in feline meningioma and indicates that further study is needed to better understand the role of these cells with respect to tumour progression and post-surgical outcome.

Controlling Rayleigh-Taylor Instabilities in Magnetically Driven Solid Metal Shells by Means of a Dynamic Screw Pinch.

Magnetically driven implosions of solid metal shells are an effective vehicle to compress materials to extreme pressures and densities. Rayleigh-Taylor instabilities (RTI) are ubiquitous, yet typically undesired features in all such experiments where solid materials are rapidly accelerated to high velocities. In cylindrical shells ("liners"), the magnetic field driving the implosion can exacerbate the RTI. We suggest an approach to implode solid metal liners enabling a remarkable reduction in the growth of magnetized RTI (MRTI) by employing a magnetic drive with a tilted, dynamic polarization, forming a dynamic screw pinch. Our calculations, based on a self-consistent analytic framework, demonstrate that the cumulative growth of the most deleterious MRTI modes may be reduced by as much as 1 to 2 orders of magnitude. One key application of this technique is to generate increasingly stable, higher-performance implosions of solid metal liners to achieve fusion [M. R. Gomez et al., Phys. Rev. Lett. 113, 155003 (2014)]. We weigh the potentially dramatic benefits of the solid liner dynamic screw pinch against the experimental tradeoffs required to achieve the desired drive field history and identify promising designs for future experimental and computational studies.

Experimental Demonstration of the Stabilizing Effect of Dielectric Coatings on Magnetically Accelerated Imploding Metallic Liners.

Enhanced implosion stability has been experimentally demonstrated for magnetically accelerated liners that are coated with 70 µm of dielectric. The dielectric tamps liner-mass redistribution from electrothermal instabilities and also buffers coupling of the drive magnetic field to the magneto-Rayleigh-Taylor instability. A dielectric-coated and axially premagnetized beryllium liner was radiographed at a convergence ratio [CR=Rin,0/Rin(z,t)] of 20, which is the highest CR ever directly observed for a strengthless magnetically driven liner. The inner-wall radius Rin(z,t) displayed unprecedented uniformity, varying from 95 to 130 µm over the 4.0 mm axial height captured by the radiograph.

Novel Receptor Specificity of Avian Gammacoronaviruses That Cause Enteritis.

UNLABELLED: Viruses exploit molecules on the target membrane as receptors for attachment and entry into host cells. Thus, receptor expression patterns can define viral tissue tropism and might to some extent predict the susceptibility of a host to a particular virus. Previously, others and we have shown that respiratory pathogens of the genus Gammacoronavirus, including chicken infectious bronchitis virus (IBV), require specific α2,3-linked sialylated glycans for attachment and entry. Here, we studied determinants of binding of enterotropic avian gammacoronaviruses, including turkey coronavirus (TCoV), guineafowl coronavirus (GfCoV), and quail coronavirus (QCoV), which are evolutionarily distant from respiratory avian coronaviruses based on the viral attachment protein spike (S1). We profiled the binding of recombinantly expressed S1 proteins of TCoV, GfCoV, and QCoV to tissues of their respective hosts. Protein histochemistry showed that the tissue binding specificity of S1 proteins of turkey, quail, and guineafowl CoVs was limited to intestinal tissues of each particular host, in accordance with the reported pathogenicity of these viruses in vivo. Glycan array analyses revealed that, in contrast to the S1 protein of IBV, S1 proteins of enteric gammacoronaviruses recognize a unique set of nonsialylated type 2 poly-N-acetyl-lactosamines. Lectin histochemistry as well as tissue binding patterns of TCoV S1 further indicated that these complex N-glycans are prominently expressed on the intestinal tract of various avian species. In conclusion, our data demonstrate not only that enteric gammacoronaviruses recognize a novel glycan receptor but also that enterotropism may be correlated with the high specificity of spike proteins for such glycans expressed in the intestines of the avian host. IMPORTANCE: Avian coronaviruses are economically important viruses for the poultry industry. While infectious bronchitis virus (IBV), a respiratory pathogen of chickens, is rather well known, other viruses of the genus Gammacoronavirus, including those causing enteric disease, are hardly studied. In turkey, guineafowl, and quail, coronaviruses have been reported to be the major causative agent of enteric diseases. Specifically, turkey coronavirus outbreaks have been reported in North America, Europe, and Australia for several decades. Recently, a gammacoronavirus was isolated from guineafowl with fulminating disease. To date, it is not clear why these avian coronaviruses are enteropathogenic, whereas other closely related avian coronaviruses like IBV cause respiratory disease. A comprehensive understanding of the tropism and pathogenicity of these viruses explained by their receptor specificity and receptor expression on tissues was therefore needed. Here, we identify a novel glycan receptor for enteric avian coronaviruses, which will further support the development of vaccines.

On the analysis of Canadian Holstein dairy cow lactation curves using standard growth functions.

Six classical growth functions (monomolecular, Schumacher, Gompertz, logistic, Richards, and Morgan) were fitted to individual and average (by parity) cumulative milk production curves of Canadian Holstein dairy cows. The data analyzed consisted of approximately 91,000 daily milk yield records corresponding to 122 first, 99 second, and 92 third parity individual lactation curves. The functions were fitted using nonlinear regression procedures, and their performance was assessed using goodness-of-fit statistics (coefficient of determination, residual mean squares, Akaike information criterion, and the correlation and concordance coefficients between observed and adjusted milk yields at several days in milk). Overall, all the growth functions evaluated showed an acceptable fit to the cumulative milk production curves, with the Richards equation ranking first (smallest Akaike information criterion) followed by the Morgan equation. Differences among the functions in their goodness-of-fit were enlarged when fitted to average curves by parity, where the sigmoidal functions with a variable point of inflection (Richards and Morgan) outperformed the other 4 equations. All the functions provided satisfactory predictions of milk yield (calculated from the first derivative of the functions) at different lactation stages, from early to late lactation. The Richards and Morgan equations provided the most accurate estimates of peak yield and total milk production per 305-d lactation, whereas the least accurate estimates were obtained with the logistic equation. In conclusion, classical growth functions (especially sigmoidal functions with a variable point of inflection) proved to be feasible alternatives to fit cumulative milk production curves of dairy cows, resulting in suitable statistical performance and accurate estimates of lactation traits.

Experimental demonstration of fusion-relevant conditions in magnetized liner inertial fusion.

This Letter presents results from the first fully integrated experiments testing the magnetized liner inertial fusion concept [S. A. Slutz et al., Phys. Plasmas 17, 056303 (2010)], in which a cylinder of deuterium gas with a preimposed 10 Taxial magnetic field is heated by Z beamlet, a 2.5 kJ, 1 TW laser, and magnetically imploded by a 19 MA, 100 ns rise time current on the Z facility. Despite a predicted peak implosion velocity of only 70 km = s, the fuel reaches a stagnation temperature of approximately 3 keV, with T(e) ≈ T(i), and produces up to 2 x 10(12) thermonuclear deuterium-deuterium neutrons. X-ray emission indicates a hot fuel region with full width at half maximum ranging from 60 to 120 µm over a 6 mm height and lasting approximately 2 ns. Greater than 10(10) secondary deuterium-tritium neutrons were observed, indicating significant fuel magnetization given that the estimated radial areal density of the plasma is only 2 mg = cm(2).

Understanding fuel magnetization and mix using secondary nuclear reactions in magneto-inertial fusion.

Magnetizing the fuel in inertial confinement fusion relaxes ignition requirements by reducing thermal conductivity and changing the physics of burn product confinement. Diagnosing the level of fuel magnetization during burn is critical to understanding target performance in magneto-inertial fusion (MIF) implosions. In pure deuterium fusion plasma, 1.01 MeV tritons are emitted during deuterium-deuterium fusion and can undergo secondary deuterium-tritium reactions before exiting the fuel. Increasing the fuel magnetization elongates the path lengths through the fuel of some of the tritons, enhancing their probability of reaction. Based on this feature, a method to diagnose fuel magnetization using the ratio of overall deuterium-tritium to deuterium-deuterium neutron yields is developed. Analysis of anisotropies in the secondary neutron energy spectra further constrain the measurement. Secondary reactions also are shown to provide an upper bound for the volumetric fuel-pusher mix in MIF. The analysis is applied to recent MIF experiments [M. R. Gomez et al., Phys. Rev. Lett. 113, 155003 (2014)] on the Z Pulsed Power Facility, indicating that significant magnetic confinement of charged burn products was achieved and suggesting a relatively low-mix environment. Both of these are essential features of future ignition-scale MIF designs.

Time course of oocyte development in winter flounder Pseudopleuronectes americanus and spawning seasonality for the Gulf of Maine, Georges Bank and southern New England stocks.

Winter flounder Pseudopleuronectes americanus were collected at monthly intervals from December 2009 to May 2011, to describe the pattern and seasonality of oocyte development, including: (1) the group-synchronous transition from primary to secondary oocytes that initiates immediately after spawning, (2) the slow (months) development of vitellogenic oocytes followed by the rapid (weeks) maturation of oocytes, (3) the synchronous nature of mature oocytes ovulating, but the discrete releases of benthic eggs in batches, (4) the protracted (months) degradation of postovulatory follicles and (5) the occurrence of follicular atresia. Although fish were collected across only c. 2° latitudinal range, the spawning season was c. 1 month later in the Gulf of Maine (GOM) than on Georges Bank and in southern New England. This is probably due to lower temperatures in the GOM. These stock-specific data regarding the time course of oogenesis are of practical value. This information is discussed in relation to measuring and interpreting elements of reproductive potential such as maturation, skipped spawning and fecundity, the response of reproductive traits by this widely distributed species to changing climate and the response by this common, marine-estuarine species to urbanization, particularly environmental pollutants and dredging.

Pulsed-coil magnet systems for applying uniform 10-30 T fields to centimeter-scale targets on Sandia's Z facility.

Sandia has successfully integrated the capability to apply uniform, high magnetic fields (10-30 T) to high energy density experiments on the Z facility. This system uses an 8-mF, 15-kV capacitor bank to drive large-bore (5 cm diameter), high-inductance (1-3 mH) multi-turn, multi-layer electromagnets that slowly magnetize the conductive targets used on Z over several milliseconds (time to peak field of 2-7 ms). This system was commissioned in February 2013 and has been used successfully to magnetize more than 30 experiments up to 10 T that have produced exciting and surprising physics results. These experiments used split-magnet topologies to maintain diagnostic lines of sight to the target. We describe the design, integration, and operation of the pulsed coil system into the challenging and harsh environment of the Z Machine. We also describe our plans and designs for achieving fields up to 20 T with a reduced-gap split-magnet configuration, and up to 30 T with a solid magnet configuration in pursuit of the Magnetized Liner Inertial Fusion concept.