Mechanical Comparison of High-Strength Tape Suture Versus High-Strength Round Suture.

PURPOSE: To compare knot and loop characteristics of commonly used high-strength tapes and high-strength round sutures. METHODS: Twenty tied 30-mm loops were prepared for using suture-knot combinations of 4 common arthroscopic knots or a hand-tied surgeon's knot and 7 sutures. Two tapes (BroadBand, SutureTape) and three no. 2 sutures (MaxBraid, FiberWire, DynaCord) were compared. Two additional larger tape sutures (FiberTape, PermaTape) not commonly tied arthroscopically were included in the hand-tied group. Each suture-knot combination was evaluated for loop integrity (single load to a specified elongation), knot security (plastic loop deformation with cyclic testing), loop security, and knot volume. Data were compared using analysis of variance followed by Tukey-Kramer post hoc tests. RESULTS: BroadBand and SutureTape demonstrated superior loop integrity compared to most no. 2 suture-knot combinations. FiberTape (430.48 ± 89.00 N) and PermaTape (545.16 ± 95.09 N) required significantly greater force to undergo 3 mm of displacement than all other hand-tied sutures (P < .001). All suture-knot configurations demonstrated significant plastic deformation (cyclic elongation) over 1000 cycles (P < 0.001). DynaCord displayed the best loop security except when paired with the Duncan loop. Overall, BroadBand and SutureTape had lower knot volumes compared to all other sutures. CONCLUSION: This study exhibits the ability of narrow tape sutures to provide reliable tissue apposition and fixation in multiple suture-knot configurations, while decreasing the potential adverse effects accompanying knot prominence. Generally, BroadBand and SutureTape demonstrated an ideal balance of mechanical characteristics to achieve the optimal suture-knot construct among those tested. Dynacord displayed superior loop security and performed best among round sutures. PermaTape and FiberTape showed greater loop integrity, albeit to the detriment of loop security and knot volume. CLINICAL RELEVANCE: When securing a rotator cuff repair construct with a knot, one should have a basic understanding of the mechanical properties of the suture and knot being used to provide the best possible repair. This study will provide information about the mechanical characteristics of commonly used high-strength tape suture knots and loops to help determine what knot type may provide the best overall construct.

The Key Pinch Stress Radiograph to Evaluate Dorsal Subluxation in the Basilar Thumb Joint.

The basilar thumb joint is the joint second most commonly affected by osteoarthritis (OA) in the hand. Evaluation of dorsal subluxation of the thumb during a functional task such as key pinch could help assess OA risk. The objectives of this study were to determine the best imaging angle for measuring thumb dorsal subluxation during key pinch and to compare subluxation to corresponding OA grades on the Eaton-Glickel, Outerbridge, and International Cartilage Repair Society scales. Eleven cadaveric forearm specimens were rigged to simulate key pinch. A mobile c-arm captured anteroposterior (AP) view images of the hand and was rotated in 5 deg increments toward the ulnar aspect of the arm up to 60 deg. Dorsal subluxation was measured on each image and compared to determine which angle captured maximum subluxation. The resulting best imaging angle was used for comparisons between dorsal subluxation of the thumb and OA grades for the basilar thumb joint. The max subluxation was in the AP view for most specimens. There was a significant correlation between subluxation and the Eaton-Glickel grade (p = 0.003, R2 = 0.779), but not with either Outerbridge grades (p = 0.8018) or International Cartilage Repair Society grades (p = 0.7001). Our results indicate that dorsal thumb subluxation during key pinch should be measured in the AP view of the forearm/hand. Dorsal thumb subluxation during key pinch had a significant correlation with the Eaton-Glickel radiographic measure of OA but not with more accurate visual classifications of OA.

Elution of rifampin and vancomycin from a weight-bearing silorane-based bone cement.

AIMS: Poly(methyl methacrylate) (PMMA)-based bone cements are the industry standard in orthopaedics. PMMA cement has inherent disadvantages, which has led to the development and evaluation of a novel silorane-based biomaterial (SBB) for use as an orthopaedic cement. In this study we test both elution and mechanical properties of both PMMA and SBB, with and without antibiotic loading. METHODS: For each cement (PMMA or SBB), three formulations were prepared (rifampin-added, vancomycin-added, and control) and made into pellets (6 mm × 12 mm) for testing. Antibiotic elution into phosphate-buffered saline was measured over 14 days. Compressive strength and modulus of all cement pellets were tested over 14 days. RESULTS: The SBB cement was able to deliver rifampin over 14 days, while PMMA was unable to do so. SBB released more vancomycin overall than did PMMA. The mechanical properties of PMMA were significantly reduced upon rifampin incorporation, while there was no effect to the SBB cement. Vancomycin incorporation had no effect on the strength of either cement. CONCLUSION: SBB was found to be superior in terms of rifampin and vancomycin elution. Additionally, the incorporation of these antibiotics into SBB did not reduce the strength of the resultant SBB cement composite whereas rifampin substantially attenuates the strength of PMMA. Thus, SBB emerges as a potential weight-bearing alternative to PMMA for the local delivery of antibiotics. Cite this article: Bone Joint Res 2021;10(4):277-284.

Biomechanics of prophylactic tethering for proximal junctional kyphosis: effects of cyclic loading on tether strength and failure properties.

STUDY DESIGN: Biomechanical evaluation of woven polyester tethers. OBJECTIVES: To quantify changes in tether elongation, stiffness, and failure characteristics after cyclic loading. Ligamentous augmentation is gaining interest as a technique to prevent proximal junctional kyphosis (PJK) in adult spinal fusions. There are a lack of data regarding the effects of cyclic loading on polyester tether mechanical properties. Tether stretch may lead to loss of stabilization and increased risk of tether failure. Biomechanical data are needed to determine the effects of cyclic loading on tether integrity. METHODS: Testing was done in two materials: (1) a synthetic cortical bone composite to determine baseline mechanical properties, and (2) nine cadaveric L1 spinous processes. 5 mm woven polyester tethers were looped through 2.5 mm holes drilled in each material. First, five tethers were tested directly to failure in the synthetic bone to establish baseline failure properties. Next, tethers were tested at one of the three cyclic load ranges [5%, 25%, and 50% (n = 5 each) of baseline failure] for 1000 cycles and then loaded to failure. Cadaveric tests were done at the 25% range and compared to synthetic bone tests at the same range. Cadaveric failure tests were classified as either tether failure or spinous process bone failure. RESULTS: Greater cyclic loading range had a significant effect on tether loop elongation, increased stiffness, and decreased ultimate tensile force. Among the cadaveric failure tests, 56% resulted in tether failure and the remaining 44% resulted in bone failure. CONCLUSIONS: Polyester tethers stretch significantly when loaded to physiological ranges. Anticipation of tether stretch may be an important consideration for a tethering strategy to prevent PJK. Improved understanding of tether material properties can provide guidance for the evaluation of clinical outcomes associated with techniques to reduce the risk of PJK caused by ligamentous laxity. LEVEL OF EVIDENCE: Biomechanical study.

Mechanical and degradation properties of poly(methyl methacrylate) cement/borate bioactive glass composites.

Bone cement is used extensively in orthopedics to anchor prostheses to bone and fill voids. Incorporating bioactive glass into poly(methyl methacrylate) (PMMA)-based bone cement could potentially improve its effectiveness for these tasks. This study characterizes the mechanical and degradation properties of composites containing PMMA-based bone cement and particles of borate bioactive glass designated as 13-93B3. Glass particles of size 5, 33, and 100 µm were mixed with PMMA bone cement to create composites containing 20, 30, and 40 wt % glass. Composites and a bone cement control were soaked in phosphate-buffered saline. Compressive strength, Young's modulus, weight loss, water uptake, solution pH, and ionic concentrations were measured over 21 days. The compressive strengths of composites decreased over 21 days. Average Young's moduli of the composites remained below 3 GPa. Weight loss and water uptake of specimens did not exceed 2 and 6%, respectively. Boron concentrations and pH of all solutions increased over time, with higher glass weight fractions leading to higher pH values. Results demonstrated that the composite can sustain glass degradation and ionic release without compromising short-term mechanical strength.

The Effect of the Joint Capsule and Anterior Oblique Ligament on Dorsal Subluxation of the First Metacarpal During Key Pinch.

Laxity of the anterior oblique ligament (AOL) and/or the dorsoradial ligament (DRL) are believed to contribute to the progression of osteoarthritis in the trapeziometacarpal joint through increased dorsal subluxation. Stress radiographs during functional tasks, such as key pinch, can be used to evaluate such joint instability. Cadaveric experiments can explore joint contact pressures as well as subluxation under varying conditions, to gain knowledge about joint mechanics. The disturbance of supporting tissues, such as the joint capsule, during experiments may affect the recorded stability of the joint. To evaluate potential effects of opening the joint capsule and severing the AOL, eleven cadaveric specimens were rigged to simulate key pinch. An anteroposterior (AP) radiograph of the hand was recorded for each specimen while intact, after partially opening the joint capsule and after sectioning the AOL. First metacarpal subluxation levels were compared between the intact joint, partially open joint capsule, and sectioned AOL. Neither opening the joint capsule nor cutting the AOL had a statistically significant effect on metacarpal subluxation. The results indicate that partially opening the joint capsule has a negligible effect on joint mechanics and support recent studies that postulate that the AOL plays a less substantial role in preventing subluxation.

Characterization of the conversion of bone cement and borate bioactive glass composites.

Borate bioactive glass 13-93B3 converts into an osteoconductive hydroxyapatite-like material in a liquid medium. In this study, 13-93B3 was incorporated into a commercial PMMA (poly(methyl methacrylate)) bone cement, and the conversion of the glass into a precipitate in solution was investigated with scanning electron microscopy, energy dispersive X-ray spectroscopy, Fourier transform infrared (spectroscopy)-attenuated total reflection, and micro-Raman spectroscopy. Glass particles of 5, 33, and 100 µm diameter were each mixed with the PMMA cement to create 20, 30, and 40% glass-loaded composites. Precipitate formation was found to be a calcium-deficient apatite partially substituted with magnesium ions that resembles native bone material and would ideally encourage bone growth better than stoichiometric hydroxyapatite. Composites of bone cement and 13-93B3 show promise as a means of encouraging bone attachment to the surface of the bone cement.

Initial Response of Mature, Experienced Runners to Barefoot Running: Transition to Forefoot Strike.

INTRODUCTION: Forefoot strike has been advocated for many runners because of the relatively lower impact and push-off forces compared to a heel strike. The purpose of this study was to explore the ability of mature (> 30 years old), experienced runners to transition from a heel foot strike to a forefoot strike when first introduced to barefoot running on a treadmill. We hypothesized: 1) mature runners who heel strike while wearing traditional training shoes would persist in heel striking immediately following a switch to barefoot, 2) mean shoe heel-to-toe drop would be significantly greater in runners who persist in heel striking when running barefoot compared to those who transition to a forefoot strike pattern, and 3) there would be a significant decrease in heel striking in the barefoot condition as running speeds increased. METHODS: This was a controlled crossover laboratory study. Thirty-three experienced runners (average 23.4 miles per week) with an average age of 45.6 years were recruited for this study. The participants first ran in their standard running shoes and subsequently barefoot. A motion capture system was utilized to detect and analyze any transition from heel strike to forefoot strike made by study participants. RESULTS: Of the 26 participants who were classified as heel strike runners in their running shoes, 50% (13/26, p = 0.001) transitioned to forefoot strike when changing from running in shoes to running barefoot. CONCLUSIONS: The injuries associated with transition from standard running shoes to barefoot running or minimalist shoes may be influenced by the persistence of heel striking in mature runners. Older experienced runners may have limited ability to transition from heel to forefoot striking when first introduced to barefoot running. Mature runners should be cautious when beginning a minimalist shoe or barefoot running regimen.

Effect of Ultrasound Frequency and Treatment Duration on Antibiotic Elution from Polymethylmethacrylate Bone Cement.

INTRODUCTION: The objective of this study was to evaluate the effect of ultrasound frequency and treatment duration on antibiotic-impregnated polymethylmethacrylate (PMMA) antibiotic elution rates and mechanical strength. METHODS: Two batches of PMMA were prepared: one with five grams of vancomycin powder and one without. Each batch was divided into two frequency groups: kHz and MHz. Each frequency group was divided into two duration groups: two minutes and ten minutes. Elution samples were measured daily using flow injection analysis. After one week of elution, ultrasound treatments were done daily until each group's average concentration fell below those of non-ultrasound control groups. After elution testing, compression testing determined mechanical properties. Paired t-tests were used to compare daily elution amounts to baseline values. Univariate ANOVAs were used to test for effects of both frequency and treatment duration on antibiotic elution amounts and on mechanical properties. RESULTS: All ultrasound treatments resulted in significant increases in antibiotic elution. Frequency and duration had significant effects of increasing antibiotic elution (p < 0.001). The kHz group produced significantly greater antibiotic elution than the MHz group (p < 0.001). The 10-minute duration produced significantly greater antibiotic elution than the two-minute duration (both p < 0.001). Frequency and duration did not have significant effects on yield stress (p = 0.841 and p = 0.179, respectively). Frequency had a significant effect (p = 0.024) on modulus, but duration did not (p = 0.136). CONCLUSIONS: Ultrasound frequency and treatment duration significantly affect antibiotic elution from PMMA which may be helpful for treatment of periprosthetic joint infections during revision arthroplasty.

Biomechanics of Prophylactic Tethering for Proximal Junctional Kyphosis: Characterization of Spinous Process Tether Pretensioning and Pull-Out Force.

STUDY DESIGN: Biomechanical evaluation of cadaver functional spinal units (FSUs). OBJECTIVES: Demonstrate the effect of increasing spinous process (SP) tether pretension on FSU flexion range of motion (ROM), intervertebral disc (IVD) pressure, and SP force. Quantify SP tether pull-out forces and relate them to SP forces generated at maximum flexion. SUMMARY OF BACKGROUND DATA: There has been recent interest in the use of SP tethering for prophylactic treatment of proximal junctional kyphosis (PJK). There is currently no consensus on standard tethering technique and no biomechanical data on the effect of tether pretension. METHODS: Nine T11-T12 FSUs were tested to 5 Nm of flexion-extension bending. A strain gauge was applied at the base of the T11 SP to measure force. Two custom pressure sensors were inserted into the anterior and posterior thirds of the IVD. Motion kinematics were measured by a motion capture system. An untethered test was done to describe baseline behavior. A 5-mm polyester tether was looped through holes drilled at the base of each SP and pretensioned to five different pretensions ranging from 0 to 88 N. Following ROM testing, specimens were dissected into individual vertebra and then SP pull-out testing was done at each level. RESULTS: Increasing pretension significantly reduced flexion ROM, reduced IVD pressures, and increased SP force. All pretensions, including the minimum, significantly reduced flexion ROM. SP pull-out forces were significantly greater than SP forces generated at maximum flexion. CONCLUSIONS: Tether pretension significantly affects segmental FSU biomechanics. Pretension should be considered an integral factor in the overall success of a tethering strategy. Efforts should be made to control and record pretension intraoperatively. LEVEL OF EVIDENCE: Level V, biomechanical study.

Biomechanics of Prophylactic Tethering for Proximal Junctional Kyphosis: Comparison of Posterior Tether Looping Techniques.

STUDY DESIGN: Biomechanical study. OBJECTIVES: Compare effects of four spinous process (SP) tether looping methods on segmental flexion range of motion (ROM), intervertebral disc (IVD) pressures, and peak tether forces. SUMMARY OF BACKGROUND DATA: SP tethering has been gaining interest as a prophylactic technique to prevent PJK caused by ligamentous laxity in ASD corrective surgery. Several SP tether looping methods have been proposed; however, there is no consensus on appropriate technique. No study has investigated the effect of the tether looping method on segmental biomechanics. METHODS: Nine T1-T4 cadaveric motion segments were tested to 5 Nm of flexion-extension. The uppermost instrumented vertebra (UIV) was located at T3 using standard pedicle screws and fusion rods. A crosslink (CL) was placed inferior to the pedicle screws. A 5-mm polyester tether was looped under the CL at UIV and through holes drilled at the base of UIV + 1 and UIV + 2 SPs. Biomechanical measurements included flexion ROM, IVD pressure, and peak tether forces at UIV/UIV + 1 and UIV + 1/UIV + 2. An untethered test was used for baseline values. Tethered tests included one single-level (SL) method and three double-level (DL) methods: common (CM), chained (CH), and figure-8 (F8). RESULTS: SL yielded significant reductions in flexion ROM at UIV/UIV + 1 (p = .001) and in IVD pressure at UIV/UIV + 1 (p = .007). Choice of DL method had a significant effect on flexion ROM at UIV/UIV + 1 (p = .004) but not at UIV + 1/UIV + 2 (p = .14). Choice of DL method also had a significant effect on IVD pressure at UIV/UIV + 1 (p < .001) but not at UIV + 1/UIV + 2 (p = .311). CM produced the greatest reductions in flexion ROM and IVD pressure, with the lowest peak tether forces among the DL methods. CONCLUSION: Tether looping method significantly alters segmental biomechanics. Tethering with the CM method to UIV + 2 allows for reductions in loads acting on the UIV + 1 SP and posterior ligaments. LEVEL OF EVIDENCE: Level V, biomechanical study.

Antibiotic Elution and Mechanical Strength of PMMA Bone Cement Loaded With Borate Bioactive Glass.

Introduction: Local delivery of antibiotics using bone cement as the delivery vehicle is an established method of managing implant-associated orthopedic infections. Various fillers have been added to cement to increase antibiotic elution, but they often do so at the expense of strength. This study evaluated the effect of adding a borate bioactive glass, previously shown to promote bone formation, on vancomycin elution from PMMA bone cement. Methods: Five cement composites were made: three loaded with borate bioactive glass along with 0, 1, and 5 grams of vancomycin and two without any glass but with 1 and 5 grams vancomycin to serve as controls. The specimens were soaked in PBS. Eluate of vancomycin was collected every 24 hours and analyzed by HPLC. Orthopedic-relevant mechanical properties of each composite were tested over time. Results: The addition of borate bioactive glass provided an increase in vancomycin release at Day 1 and an increase in sustained vancomycin release throughout the treatment period. An 87.6% and 21.1% increase in cumulative vancomycin release was seen for both 1g and 5g loading groups, respectively. Compressive strength of all composites remained above the weight-bearing threshold of 70 MPa throughout the duration of the study with the glass-containing composites showing comparable strength to their respective controls. Conclusion: The incorporation of borate bioactive glass into commercial PMMA bone cement can significantly increase the elution of vancomycin. The mechanical strength of the cement-glass composites remained above 70 MPa even after soaking for 8 weeks, suggesting their suitability for orthopedic weight-bearing applications.

Evaluation of midcarpal capitate contact mechanics in normal, injured and post-operative wrists.

BACKGROUND: Scapholunate ligament injury is a commonly occurring carpal ligament injury. Pathology associated with scapholunate ligament injury depends on several factors such as the time after injury, type of injury (instability) and the development of osteoarthritis. The aim of this study was to investigate and compare contact mechanics in the lunocapitate and scaphocapitate joints in the normal, injured (scapholunate dissociation) and repaired (postoperative) wrist. METHODS: Four human subjects with scapholunate ligament dissociation participated in this study. MR images of normal (contralateral), injured and postoperative wrists were obtained during relaxed condition and during active light grasp. Relaxed MR images were used to construct model geometry (bones with cartilage) for the capitate, lunate and scaphoid. Kinematic transformations were obtained by using image registration between the unloaded and functionally loaded image sets. Joint surface contact mechanics were then calculated. FINDINGS: All contact measures (contact force, pressure, mean pressure and area) tended to increase with injury in both articulations. A significantly higher contact area was found in the injured scaphocapitate joint compared to normal. A significant increase in peak pressure was observed in the postoperative state compared to normal. INTERPRETATION: Injury to the scapholunate ligament increased contact measures, suggesting a risk for onset of osteoarthritis in both the scaphocapitate and lunocapitate joints. Surgical repair appeared to restore most measures of contact mechanics to near normal values, more so for the lunocapitate joint when compared to scaphocapitate joint. The elevated postoperative peak pressures indicate the difficulty to fully restore joint mechanics.

Evaluation of meniscal extrusion with posterior root disruption and repair using ultrasound.

BACKGROUND: Ultrasound techniques have been utilized for detection of discrete meniscus tears and extrusion. Meniscal extrusion is associated with increased contact pressure and decreased contact area contributing to the advancement of knee osteoarthritis. The purpose of this biomechanical study was to detect meniscal extrusion using a clinically available, portable ultrasound device. And further, to show that extent of injury and a weight-bearing state correlate with amount of extrusion. METHODS: A portable, hand-held ultrasound was utilized to image the lateral meniscus in association with (1) an intact posterior root attachment, (2) a 50% cut, (3) a 100% cut, and (4) repaired posterior root attachment. Images were obtained in an unloaded condition, and again under a static, physiologic (70kg) axial load for above injury levels, and again following repair. RESULTS: Significant differences in extrusion were noted between the intact and both the 50% cut (p=0.028) and 100% cut groups (p<0.001) all in the loaded position. No significant difference was found in extrusion between intact state and repaired posterior root in the axially loaded position (p=0.174). Both load (p=0.003) and injury level (p=0.005) had significant effects on the mean extrusion of the lateral meniscus. CONCLUSION: Sectioning of the lateral meniscus posterior root will produce significantly increased lateral extrusion of the meniscus under physiologic loads. Unlike MRI evaluation, weight-bearing ultrasound images allow a functional assessment of meniscus extrusion. Trans-tibial posterior root repair can restore the lateral meniscus position and integrity. CLINICAL RELEVANCE: This weight-bearing ultrasound technique can be an important assessment tool for complete evaluation of meniscus injuries.

Intrawound Vancomycin Powder Decreases Staphylococcal Surgical Site Infections After Posterior Instrumented Spinal Arthrodesis.

STUDY DESIGN: A retrospective historical cohort design. OBJECTIVE: To determine what effect the addition of intrawound vancomycin powder to the prophylactic regimen of posterior instrumented spinal arthrodesis procedures has had on acute surgical site infections (SSIs). SUMMARY OF BACKGROUND DATA: SSIs are known complications in instrumented spinal arthrodesis procedures, and are predominately caused by Staphylococcus aureus. Recent reports have suggested that placing vancomycin powder into the surgical wound before closure prevents SSIs in spinal surgery. Risk factors for SSIs in the setting of intrawound vancomycin powder use have not been previously reported on. MATERIALS AND METHODS: SSI rates after 342 posterior instrumented spinal arthrodeses (October 2008-September 2011) in which intrawound vancomycin powder was used in addition to the standard antimicrobial prophylaxis (Vanco cohort) were compared with 341 posterior instrumented spinal arthrodeses (April 2005-October 2008) in which no vancomycin powder was added (non-Vanco cohort). Both 2 sample t test and χ test (Fisher where appropriate) were used for group comparisons. A subanalysis of the Vanco cohort was undertaken to identify risk factors for SSIs despite intrawound vancomycin use. RESULTS: There was a significant reduction in the number of acute staphylococcal SSIs in the Vanco cohort (1.1%) compared with the non-Vanco cohort (3.8%; P=0.029). Deep staphylococcal infections decreased to 0 compared with 7 in the non-Vanco cohort (2.1%; P=0.008). Deep methicillin-resistant S. aureus infections decreased to 0 compared with 5 in the non-Vanco cohort (1.5%; P=0.031). A subanalysis of the Vanco cohort identified that being discharged to an inpatient rehabilitation or skilled nursing facility was associated with developing a SSI. CONCLUSIONS: Intrawound vancomycin powder use has decreased the rate of acute staphylococcal SSIs in our posterior instrumented spine arthrodesis surgeries. Patients who are discharged to skilled nursing or rehabilitation facilities are at an increased risk for developing SSIs despite intrawound vancomycin use.

Neuroanatomical distribution of mechanoreceptors in the human cadaveric shoulder capsule and labrum.

The distribution, location, and spatial arrangement of mechanoreceptors are important for neural signal conciseness and accuracy in proprioceptive information required to maintain functional joint stability. The glenohumeral joint capsule and labrum are mechanoreceptor-containing tissues for which the distribution of mechanoreceptors has not been determined despite the importance of these tissues in stabilizing the shoulder. More recently, it has been shown that damage to articular mechanoreceptors can result in proprioceptive deficits that may lead to recurrent instability. Awareness of mechanoreceptor distribution in the glenohumeral joint capsule and labrum may allow preservation of the mechanoreceptors during surgical treatment for shoulder instability, and in turn retain the joint's proprioceptive integrity. For this reason, we sought to develop a neuroanatomical map of the mechanoreceptors within the capsule and labrum. We postulated that the mechanoreceptors in these tissues are distributed in a unique pattern, with mechanoreceptor-scarce regions that may be more appropriate for surgical dissection. We determined the neuroanatomical distribution of mechanoreceptors and their associated fascicles in the capsule and labrum from eight human cadaver shoulder pairs using our improved gold chloride staining technique and light microscopy. A distribution pattern was consistently observed in the capsule and labrum from which we derived a neuroanatomical map. Both tissues demonstrated mechanoreceptor-dense and -scarce regions that may be considered during surgical treatment for instability. Capsular fascicles were located in the subsynovial layer, whereas labral fascicles were concentrated in the peri-core zone. The capsular fascicles presented as a lattice network and with a plexiform appearance. Fascicles within the labrum resembled a cable structure with the fascicles running in parallel. Our findings contribute to the neuroanatomical knowledge of the two glenohumeral joint stabilizers, namely, capsule and labrum, primarily involved in the onset of shoulder instability and recurrent instability. Neuroanatomical knowledge of articular mechanoreceptors is important for (i) developing a topographical map that reflects correspondence between the joint and surrounding musculature, (ii) understanding proprioceptive deficits that are only partially restored post surgical and post rehabilitative treatment, and (iii) gaining further knowledge about articular mechanoreceptors.

Rotational stability for intercarpal fixation is enhanced by a 4-tine staple.

PURPOSE: To compare the torsional stability of 6 fixation techniques for intercarpal fixation including a 4-tine, in-line staple. METHODS: We chose the scapholunate interval as the test site for rotational stability for various constructs. We used 42 pairs of embalmed scaphoids and lunates for the comparisons and created 6 construct groups. Fixation of the scapholunate gap was performed with a 3-mm screw, 2 1.1-mm (0.045-inch) K-wires spaced 2 mm apart, or 2 1.1-mm K-wires spaced 5 mm apart. One member of each pair was fixed with either a standard 2-tine peripherally placed staple or a customized 4-tine staple. Each scapholunate construct was tested in torsion to failure on a biaxial materials testing machine. RESULTS: In all cases, the 4-tine staple significantly increased rotational stability. The 2-tine staple resulted in statistically insignificant increases in rotational stability. With central fixation alone, K-wires separated by 5 mm showed the greatest resistance to torsion, and the 3-mm screw showed the least. CONCLUSIONS: Use of an in-line, 4-tine staple provided increased rotational stability and may result in enhanced healing of intercarpal ligamentous reconstructions and arthrodeses. CLINICAL RELEVANCE: A 4-tine staple compared with a standard staple provided superior rotational stability for intercarpal fixation.

Computationally efficient magnetic resonance imaging based surface contact modeling as a tool to evaluate joint injuries and outcomes of surgical interventions compared to finite element modeling.

Joint injuries and the resulting posttraumatic osteoarthritis (OA) are a significant problem. There is still a need for tools to evaluate joint injuries, their effect on joint mechanics, and the relationship between altered mechanics and OA. Better understanding of injuries and their relationship to OA may aid in the development or refinement of treatment methods. This may be partially achieved by monitoring changes in joint mechanics that are a direct consequence of injury. Techniques such as image-based finite element modeling can provide in vivo joint mechanics data but can also be laborious and computationally expensive. Alternate modeling techniques that can provide similar results in a computationally efficient manner are an attractive prospect. It is likely possible to estimate risk of OA due to injury from surface contact mechanics data alone. The objective of this study was to compare joint contact mechanics from image-based surface contact modeling (SCM) and finite element modeling (FEM) in normal, injured (scapholunate ligament tear), and surgically repaired radiocarpal joints. Since FEM is accepted as the gold standard to evaluate joint contact stresses, our assumption was that results obtained using this method would accurately represent the true value. Magnetic resonance images (MRI) of the normal, injured, and postoperative wrists of three subjects were acquired when relaxed and during functional grasp. Surface and volumetric models of the radiolunate and radioscaphoid articulations were constructed from the relaxed images for SCM and FEM analyses, respectively. Kinematic boundary conditions were acquired from image registration between the relaxed and grasp images. For the SCM technique, a linear contact relationship was used to estimate contact outcomes based on interactions of the rigid articular surfaces in contact. For FEM, a pressure-overclosure relationship was used to estimate outcomes based on deformable body contact interactions. The SCM technique was able to evaluate variations in contact outcomes arising from scapholunate ligament injury and also the effects of surgical repair, with similar accuracy to the FEM gold standard. At least 80% of contact forces, peak contact pressures, mean contact pressures and contact areas from SCM were within 10 N, 0.5 MPa, 0.2 MPa, and 15 mm2, respectively, of the results from FEM, regardless of the state of the wrist. Depending on the application, the MRI-based SCM technique has the potential to provide clinically relevant subject-specific results in a computationally efficient manner compared to FEM.

Validation of radiocarpal joint contact models based on images from a clinical MRI scanner.

This study was undertaken to assess magnetic resonance imaging (MRI)-based radiocarpal surface contact models of functional loading in a clinical MRI scanner for future in vivo studies, by comparison with experimental measures from three cadaver forearm specimens. Experimental data were acquired using a Tekscan sensor during simulated light grasp. Magnetic resonance (MR) images were used to obtain model geometry and kinematics (image registration). Peak contact pressures (PPs) and average contact pressures (APs), contact forces and contact areas were determined in the radiolunate and radioscaphoid joints. Contact area was also measured directly from MR images acquired with load and compared with model data. Based on the validation criteria (within 25% of experimental data), out of the six articulations (three specimens with two articulations each), two met the criterion for AP (0%, 14%); one for peak pressure (20%); one for contact force (5%); four for contact area with respect to experiment (8%, 13%, 19% and 23%), and three contact areas met the criterion with respect to direct measurements (14%, 21% and 21%). Absolute differences between model and experimental PPs were reasonably low (within 2.5 MPa). Overall, the results indicate that MRI-based models generated from 3T clinical MR scanner appear sufficient to obtain clinically relevant data.

Biomechanical Analysis of Cement Augmentation Techniques on Pedicle Screw Fixation in Osteopenic Bone: A Cadaveric Study.

STUDY DESIGN: Three techniques for cement injection into osteopenic pedicles for screw augmentation were compared in a cadaver model. OBJECTIVES: To compare the safety and efficacy of 3 techniques for cement augmentation of pedicle screws in a cadaver model. BACKGROUND: Cement augmentation of pedicle screws improves fixation in osteopenic spines. Some investigators have used kyphoplasty osteo introducers to inject viscous cement into the pedicle. In addition, a novel fenestrated tapping system was studied that leaves a threaded cement tract for final pedicle screw insertion. METHODS: This 3-phase biomechanical study compared cement augmentation effects on the cephalocaudal toggle of pedicle screws within 34 fresh osteopenic human cadaveric vertebrae. Phase 1 compared injection through a fenestrated tap to a direct injection. Phase 2 evaluated the fenestrated tap versus injection of more viscous cement using a kyphoplasty osteo inducer. Phase 3 compared kyphoplasty and direct injection techniques. Each vertebral body was prepared with each of the 2 techniques. The pedicle screws were subjected to 10,000 cycles of cephalocaudal toggling, and total vertical displacement of each screw head was measured. RESULTS: In a combined analysis, overall displacement was 2.26 ± 0.57 mm for the direct injection, 2.88 ± 0.56 mm for the kyphoplasty technique, and 3.74 ± 0.59 mm for the fenestrated tap (p < .01). In Phase 1, extravasation of cement occurred in 5% of the fenestrated tap, 86% of the direct injection. Phase 2 results showed that extravasation occurred in 0% for the fenestrated tap group and 18% for the kyphoplasty group. In Phase 3, extravasation of cement was 54% of the direct injection, compared with 31% of the kyphoplasty group. CONCLUSIONS: The novel fenestrated tap system provided less resistance to toggle than either of the other 2 techniques but provided a lower incidence of cement extravasation. More viscous cement injected using kyphoplasty technique provides a combination of safety and efficacy.