Tuning and Coupling Irreversible Electroosmotic Water Flow in Ionic Diodes: Methylation of an Intrinsically Microporous Polyamine (PIM-EA-TB).

Molecularly rigid polymers with internal charges (positive charges induced by amine methylation) allow electroosmotic water flow to be tuned by adjusting the charge density (the degree of methylation). Here, a microporous polyamine (PIM-EA-TB) is methylated to give a molecularly rigid anion conductor. The electroosmotic drag coefficient (the number of water molecules transported per anion) is shown to increase with a lower degree of methylation. Net water transport (without charge flow) in a coupled anionic diode circuit is demonstrated based on combining low and high electroosmotic drag coefficient materials. The AC-electricity-driven net process offers water transport (or transport of other neutral species, e.g., drugs) with net zero ion transport and without driver electrode side reactions.

Thin Film Composite Membranes with Regulated Crossover and Water Migration for Long-Life Aqueous Redox Flow Batteries.

Redox flow batteries (RFBs) are promising for large-scale long-duration energy storage owing to their inherent safety, decoupled power and energy, high efficiency, and longevity. Membranes constitute an important component that affects mass transport processes in RFBs, including ion transport, redox-species crossover, and the net volumetric transfer of supporting electrolytes. Hydrophilic microporous polymers, such as polymers of intrinsic microporosity (PIM), are demonstrated as next-generation ion-selective membranes in RFBs. However, the crossover of redox species and water migration through membranes are remaining challenges for battery longevity. Here, a facile strategy is reported for regulating mass transport and enhancing battery cycling stability by employing thin film composite (TFC) membranes prepared from a PIM polymer with optimized selective-layer thickness. Integration of these PIM-based TFC membranes with a variety of redox chemistries allows for the screening of suitable RFB systems that display high compatibility between membrane and redox couples, affording long-life operation with minimal capacity fade. Thickness optimization of TFC membranes further improves cycling performance and significantly restricts water transfer in selected RFB systems.

Nanophase-photocatalysis: loading, storing, and release of H2O2 using graphitic carbon nitride.

A blue light mediated photochemical process using solid graphitic carbon nitride (g-C3N4) in ambient air/isopropanol vapour is suggested to be linked to "nanophase" water inclusions and is shown to produce approx. 50 µmol H2O2 per gram of g-C3N4, which can be stored in the solid g-C3N4 for later release for applications, for example, in disinfection or anti-bacterial surfaces.

Near-frictionless ion transport within triazine framework membranes.

The enhancement of separation processes and electrochemical technologies such as water electrolysers1,2, fuel cells3,4, redox flow batteries5,6 and ion-capture electrodialysis7 depends on the development of low-resistance and high-selectivity ion-transport membranes. The transport of ions through these membranes depends on the overall energy barriers imposed by the collective interplay of pore architecture and pore-analyte interaction8,9. However, it remains challenging to design efficient, scaleable and low-cost selective ion-transport membranes that provide ion channels for low-energy-barrier transport. Here we pursue a strategy that allows the diffusion limit of ions in water to be approached for large-area, free-standing, synthetic membranes using covalently bonded polymer frameworks with rigidity-confined ion channels. The near-frictionless ion flow is synergistically fulfilled by robust micropore confinement and multi-interaction between ion and membrane, which afford, for instance, a Na+ diffusion coefficient of 1.18 × 10-9 m2 s-1, close to the value in pure water at infinite dilution, and an area-specific membrane resistance as low as 0.17 Ω cm2. We demonstrate highly efficient membranes in rapidly charging aqueous organic redox flow batteries that deliver both high energy efficiency and high-capacity utilization at extremely high current densities (up to 500 mA cm-2), and also that avoid crossover-induced capacity decay. This membrane design concept may be broadly applicable to membranes for a wide range of electrochemical devices and for precise molecular separation.

ECL sensor for selective determination of citrate ions as a prostate cancer biomarker using polymer of intrinsic microporosity-1 nanoparticles/nitrogen-doped carbon quantum dots.

Urine citrate analysis is relevant in the screening and monitoring of patients with prostate cancer and calcium nephrolithiasis. A sensitive, fast, easy, and low-maintenance electrochemiluminescence (ECL) method with conductivity detection for the analysis of citrate in urine is developed and validated by employing polymer of intrinsic microporosity-1 nanoparticles/nitrogen-doped carbon quantum dots (nano-PIM-1/N-CQDs). Using optimum conditions, the sensor was applied in ECL experiments in the presence of different concentrations of citrate ions. The ECL signals were quenched gradually by the increasing citrate concentration. The linear range of the relationship between the logarithm of the citrate concentration and ΔECL (ECL of blank - ECL of sample) was obtained between 1.0 × 10-7 M and 5.0 × 10-4 M. The limit of detection (LOD) was calculated to be 2.2 × 10-8 M (S/N = 3). The sensor was successfully applied in real samples such as human serum and patient urine.

Ion-Selective Microporous Polymer Membranes with Hydrogen-Bond and Salt-Bridge Networks for Aqueous Organic Redox Flow Batteries.

Redox flow batteries (RFBs) have great potential for long-duration grid-scale energy storage. Ion-conducting membranes are a crucial component in RFBs, allowing charge-carrying ions to transport while preventing the cross-mixing of redox couples. Commercial Nafion membranes are widely used in RFBs, but their unsatisfactory ionic and molecular selectivity, as well as high costs, limit the performance and the widespread deployment of this technology. To extend the longevity and reduce the cost of RFB systems, inexpensive ion-selective membranes that concurrently deliver low ionic resistance and high selectivity toward redox-active species are highly desired. Here, high-performance RFB membranes are fabricated from blends of carboxylate- and amidoxime-functionalized polymers of intrinsic microporosity, which exploit the beneficial properties of both polymers. The enthalpy-driven formation of cohesive interchain interactions, including hydrogen bonds and salt bridges, facilitates the microscopic miscibility of the blends, while ionizable functional groups within the sub-nanometer pores allow optimization of membrane ion-transport functions. The resulting microporous membranes demonstrate fast cation conduction with low crossover of redox-active molecular species, enabling improved power ratings and reduced capacity fade in aqueous RFBs using anthraquinone and ferrocyanide as redox couples.

Dibenzomethanopentacene-Based Polymers of Intrinsic Microporosity for Use in Gas-Separation Membranes.

Dibenzomethanopentacene (DBMP) is shown to be a useful structural component for making Polymers of Intrinsic Microporosity (PIMs) with promise for making efficient membranes for gas separations. DBMP-based monomers for PIMs are readily prepared using a Diels-Alder reaction between 2,3-dimethoxyanthracene and norbornadiene as the key synthetic step. Compared to date for the archetypal PIM-1, the incorporation of DBMP simultaneously enhances both gas permeability and the ideal selectivity for one gas over another. Hence, both ideal and mixed gas permeability data for DBMP-rich co-polymers and an amidoxime modified PIM are close to the current Robeson upper bounds, which define the state-of-the-art for the trade-off between permeability and selectivity, for several important gas pairs. Furthermore, long-term studies (over ≈3 years) reveal that the reduction in gas permeabilities on ageing is less for DBMP-containing PIMs relative to that for other high performing PIMs, which is an attractive property for the fabrication of membranes for efficient gas separations.

Solution-Processable Redox-Active Polymers of Intrinsic Microporosity for Electrochemical Energy Storage.

Redox-active organic materials have emerged as promising alternatives to conventional inorganic electrode materials in electrochemical devices for energy storage. However, the deployment of redox-active organic materials in practical lithium-ion battery devices is hindered by their undesired solubility in electrolyte solvents, sluggish charge transfer and mass transport, as well as processing complexity. Here, we report a new molecular engineering approach to prepare redox-active polymers of intrinsic microporosity (PIMs) that possess an open network of subnanometer pores and abundant accessible carbonyl-based redox sites for fast lithium-ion transport and storage. Redox-active PIMs can be solution-processed into thin films and polymer-carbon composites with a homogeneously dispersed microstructure while remaining insoluble in electrolyte solvents. Solution-processed redox-active PIM electrodes demonstrate improved cycling performance in lithium-ion batteries with no apparent capacity decay. Redox-active PIMs with combined properties of intrinsic microporosity, reversible redox activity, and solution processability may have broad utility in a variety of electrochemical devices for energy storage, sensors, and electronic applications.

Thin Film Composite Membranes Based on the Polymer of Intrinsic Microporosity PIM-EA(Me2)-TB Blended with Matrimid®5218.

In this work, thin film composite (TFC) membranes were fabricated with the selective layer based on a blend of polyimide Matrimid®5218 and polymer of intrinsic microporosity (PIM) composed of Tröger's base, TB, and dimethylethanoanthracene units, PIM-EA(Me2)-TB. The TFCs were prepared with different ratios of the two polymers and the effect of the PIM content in the blend of the gas transport properties was studied for pure He, H2, O2, N2, CH4, and CO2 using the well-known time lag method. The prepared TFC membranes were further characterized by IR spectroscopy and scanning electron microscopy (SEM). The role of the support properties for the TFC membrane preparation was analysed for four different commercial porous supports (Nanostone Water PV 350, Vladipor Fluoroplast 50, Synder PAN 30 kDa, and Sulzer PAN UF). The Sulzer PAN UF support with a relatively small pore size favoured the formation of a defect-free dense layer. All the TFC membranes supported on Sulzer PAN UF presented a synergistic enhancement in CO2 permeance, and CO2/CH4 and CO2/N2 ideal selectivity. The permeance increased about two orders of magnitude with respect to neat Matrimid, up to ca. 100 GPU, the ideal CO2/CH4 selectivity increased from approximately 10 to 14, and the CO2/N2 selectivity from approximately 20 to 26 compared to the thick dense reference membrane of PIM-EA(Me2)-TB. The TFC membranes exhibited lower CO2 permeances than expected on the basis of their thickness-most likely due to enhanced aging of thin films and to the low surface porosity of the support membrane, but a higher selectivity for the gas pairs CO2/N2, CO2/CH4, O2/N2, and H2/N2.

2,2'-Biphenol-based Ultrathin Microporous Nanofilms for Highly Efficient Molecular Sieving Separation.

Organic solvent nanofiltration (OSN) is an emerging membrane separation technology, which urgently requires robust, easily processed, OSN membranes possessing high permeance and small solutes-selectivity to facilitate enhanced industrial uptake. Herein, we describe the use of two 2,2'-biphenol (BIPOL) derivatives to fabricate hyper-crosslinked, microporous polymer nanofilms through IP. Ultra-thin, defect-free polyesteramide/polyester nanofilms (≈5 nm) could be obtained readily due to the relatively large molecular size and ionized nature of the BIPOL monomers retarding the rate of the IP. The enhanced microporosity arises from the hyper-crosslinked network structure and monomer rigidity. Specifically, the amino-BIPOL/PAN membrane exhibits extraordinary permselectivity performances with molecular weight cut-off as low as 233 Da and MeOH permeance of ≈13 LMH/bar. Precise separation of small dye mixtures with similar M.W. based on both their charge and molecular size are achieved.

Long-Life Aqueous Organic Redox Flow Batteries Enabled by Amidoxime-Functionalized Ion-Selective Polymer Membranes.

Redox flow batteries (RFBs) based on aqueous organic electrolytes are a promising technology for safe and cost-effective large-scale electrical energy storage. Membrane separators are a key component in RFBs, allowing fast conduction of charge-carrier ions but minimizing the cross-over of redox-active species. Here, we report the molecular engineering of amidoxime-functionalized Polymers of Intrinsic Microporosity (AO-PIMs) by tuning their polymer chain topology and pore architecture to optimize membrane ion transport functions. AO-PIM membranes are integrated with three emerging aqueous organic flow battery chemistries, and the synergetic integration of ion-selective membranes with molecular engineered organic molecules in neutral-pH electrolytes leads to significantly enhanced cycling stability.

Development of efficient aqueous organic redox flow batteries using ion-sieving sulfonated polymer membranes.

Redox flow batteries using aqueous organic-based electrolytes are promising candidates for developing cost-effective grid-scale energy storage devices. However, a significant drawback of these batteries is the cross-mixing of active species through the membrane, which causes battery performance degradation. To overcome this issue, here we report size-selective ion-exchange membranes prepared by sulfonation of a spirobifluorene-based microporous polymer and demonstrate their efficient ion sieving functions in flow batteries. The spirobifluorene unit allows control over the degree of sulfonation to optimize the transport of cations, whilst the microporous structure inhibits the crossover of organic molecules via molecular sieving. Furthermore, the enhanced membrane selectivity mitigates the crossover-induced capacity decay whilst maintaining good ionic conductivity for aqueous electrolyte solution at pH 9, where the redox-active organic molecules show long-term stability. We also prove the boosting effect of the membranes on the energy efficiency and peak power density of the aqueous redox flow battery, which shows stable operation for about 120 h (i.e., 2100 charge-discharge cycles at 100 mA cm-2) in a laboratory-scale cell.

Effects of g-C3N4 Heterogenization into Intrinsically Microporous Polymers on the Photocatalytic Generation of Hydrogen Peroxide.

Graphitic carbon nitride (g-C3N4) is known to photogenerate hydrogen peroxide in the presence of hole quenchers in aqueous environments. Here, the g-C3N4 photocatalyst is embedded into a host polymer of intrinsic microporosity (PIM-1) to provide recoverable heterogenized photocatalysts without loss of activity. Different types of g-C3N4 (including Pt@g-C3N4, Pd@g-C3N4, and Au@g-C3N4) and different quenchers are investigated. Exploratory experiments yield data that suggest binding of the quencher either (i) directly by adsorption onto the g-C3N4 (as shown for α-glucose) or (ii) indirectly by absorption into the microporous polymer host environment (as shown for Triton X-100) enhances the overall photochemical H2O2 production process. The amphiphilic molecule Triton X-100 is shown to interact only weakly with g-C3N4 but strongly with PIM-1, resulting in accumulation and enhanced H2O2 production due to the microporous polymer host.

Non-enzymatic electrochemical cholesterol sensor based on strong host-guest interactions with a polymer of intrinsic microporosity (PIM) with DFT study.

Advances in materials science have accelerated the development of diagnostic tools with the last decade witnessing the development of enzyme-free sensors, owing to the improved stability, low cost and simple fabrication of component materials. However, the specificity of non-enzymatic sensors for certain analytes still represents a challenging task, for example the determination of cholesterol level in blood is vital due to its medical relevance. In this work, a reagent displacement assay for cholesterol sensing in serum samples was developed. It is based on coating of a glassy carbon electrode with a polymer of intrinsic microporosity (PIM) that forms a host-guest complex with methylene blue (MB). In the presence of cholesterol, the MB electroactive probe was displaced due to the stronger association of cholesterol guest to the PIM host. The decrease in the oxidative current was proportional to the cholesterol concentration achieving a detection limit of approximately 0.1 nM. Moreover, to further assist the experimental studies, comprehensive theoretical calculations are also performed by using density functional theory (DFT) calculations.

Control Over the Morphology of Electrospun Microfibrous Mats of a Polymer of Intrinsic Microporosity.

This study reports for the first time the preparation of an electrospun microfibrous mat of PIM-EA-TB. The electrospinning was carried out using a chloroform/n-Propyl-lactate (n-PL) binary solvent system with different chloroform/nPL ratios, in order to control the morphology of the microfibres. With pure chloroform, porous and dumbbell shape fibres were obtained whereas, with the addition on n-PL, circular and thinner fibres have been produced due to the higher boiling point and the higher conductivity of n-PL. The electrospinning process conditions were investigated to evaluate their impact on the fibres' morphology. These microfibrous mats presented potential to be used as breathable/waterproof materials, with a pore diameter of 11 µm, an air resistance of 25.10-7 m-1 and water breakthrough pressure of 50 mBar.

Catechin or quercetin guests in an intrinsically microporous polyamine (PIM-EA-TB) host: accumulation, reactivity, and release.

Microporous polymer materials based on molecularly "stiff" structures provide intrinsic microporosity, typical micropore sizes of 0.5 nm to 1.5 nm, and the ability to bind guest species. The polyamine PIM-EA-TB contains abundant tertiary amine sites to interact via hydrogen bonding to guest species in micropores. Here, quercetin and catechin are demonstrated to bind and accumulate into PIM-EA-TB. Voltammetric data suggest apparent Langmuirian binding constants for catechin of 550 (±50) × 103 M-1 in acidic solution at pH 2 (PIM-EA-TB is protonated) and 130 (±13) × 103 M-1 in neutral solution at pH 6 (PIM-EA-TB is not protonated). The binding capacity is typically 1 : 1 (guest : host polymer repeat unit), but higher loadings are readily achieved by host/guest co-deposition from tetrahydrofuran solution. In the rigid polymer environment, bound ortho-quinol guest species exhibit 2-electron 2-proton redox transformation to the corresponding quinones, but only in a thin mono-layer film close to the electrode surface. Release of guest molecules occurs depending on the level of loading and on the type of guest either spontaneously or with electrochemical stimuli.

Polymers of Intrinsic Microporosity in the Design of Electrochemical Multicomponent and Multiphase Interfaces.

Polymers of intrinsic microporosity (or PIMs) provide porous materials due to their highly contorted and rigid macromolecular structures, which prevent space-efficient packing. PIMs are readily dissolved in solvents and can be cast into robust microporous coatings and membranes. With a typical micropore size range of around 1 nm and a typical surface area of 700-1000 m2 g-1, PIMs offer channels for ion/molecular transport and pores for gaseous species, solids, and liquids to coexist. Electrode surfaces are readily modified with coatings or composite films to provide interfaces for solid|solid|liquid or solid|liquid|liquid or solid|liquid|gas multiphase electrode processes.

Mitigation of Physical Aging with Mixed Matrix Membranes Based on Cross-Linked PIM-1 Fillers and PIM-1.

A low cross-link density (LCD) network-PIM-1, which offers high compatibility with the polymer of intrinsic microporosity PIM-1, is synthesized by a modified PIM-1 polycondensation that combines both a tetrafluoro- and an octafluoro-monomer. To maximize the advantages of utilizing such cross-linked PIM-1 fillers in PIM-1-based mixed matrix membranes (MMMs), a grafting route is used to decorate the LCD-network-PIM-1 (dispersed phase) with PIM-1 chains, to further enhance compatibility with the PIM-1 matrix. Mixed-gas CO2/CH4 (1:1, v/v) separation results over 160 days of membrane aging confirm the success of a relatively short (24 h) grafting reaction in improving the initial CO2 separation performance, as well as hindering the aging of PIM-1/grafted-LCD-network-PIM-1 MMMs. For MMMs based on a 24 h grafting route, all the gas separation data surpass the 2008 Robeson upper bound by a significant margin, and the 160-day aged membranes show only 29% reduction from the initial CO2 permeability, which is substantially less than the equivalent losses of nearly 70% and 48% for PIM-1 and traditionally fabricated MMMs counterparts, respectively. These results demonstrate the potential of network-PIM components for obtaining much more stable gas separation performance over extended periods of time.

Tailoring molecular interactions between microporous polymers in high performance mixed matrix membranes for gas separations.

Membranes are crucial to lowering the huge energy costs of chemical separations. Whilst some promising polymers demonstrate excellent transport properties, problems of plasticisation and physical aging due to mobile polymer chains, amongst others, prevent their exploitation in membranes for industrial separations. Here we reveal that molecular interactions between a polymer of intrinsic microporosity (PIM) matrix and a porous aromatic framework additive (PAF-1) can simultaneously address plasticisation and physical aging whilst also increasing gas transport selectivity. Extensive spectroscopic characterisation and control experiments involving two near-identical PIMs, one with methyl groups (PIM-EA(Me2)-TB) and one without (PIM-EA(H2)-TB), directly confirm the key molecular interaction as the adsoprtion of methyl groups from the PIM matrix into the nanopores of the PAF. This interaction reduced physical aging by 50%, suppressed polymer chain mobilities at high pressure and increased H2 selectivity over larger gases such as CH4 and N2.

Effect of Bridgehead Methyl Substituents on the Gas Permeability of Tröger's-Base Derived Polymers of Intrinsic Microporosity.

A detailed comparison of the gas permeability of four Polymers of Intrinsic Microporosity containing Tröger's base (TB-PIMs) is reported. In particular, we present the results of a systematic study of the differences between four related polymers, highlighting the importance of the role of methyl groups positioned at the bridgehead of ethanoanthracene (EA) and triptycene (Trip) components. The PIMs show BET surface areas between 845-1028 m2 g-1 and complete solubility in chloroform, which allowed for the casting of robust films that provided excellent permselectivities for O2/N2, CO2/N2, CO2/CH4 and H2/CH4 gas pairs so that some data surpass the 2008 Robeson upper bounds. Their interesting gas transport properties were mostly ascribed to a combination of high permeability and very strong size-selectivity of the polymers. Time lag measurements and determination of the gas diffusion coefficient of all polymers revealed that physical ageing strongly increased the size-selectivity, making them suitable for the preparation of thin film composite membranes.