RESUMO
Traffic pollution has been linked to high levels of metals and organic contaminants in road-side soils, largely due to abrasion of tires, brake pads and the road surface. Although several studies have demonstrated correlations between different pollutants and various traffic variables, they mainly focused on roads with medium to high traffic density (>30,000 vehicles per day). In this study we have focused on investigating tire wear particles and road-related metals (zinc, copper, lead, chromium, nickel, and the metalloid arsenic) in the soils of low traffic roads in rural areas (650-14,250 vehicles per day). Different explanatory factors were investigated, such as traffic density, speed, % heavy vehicles, organic matter content, annual precipitation, soil types and roadside slope profiles. The results show high levels of tire wear particles, from 2000 to 26,400 mg/kg (0.2-2.6 % tire wear in d.w. soil), which is up to five times higher compared to previously reported values in roadside soils of high traffic density areas. A weak but significant correlation was found between tire wear particles, traffic speed and the annual precipitation. No significant relationship was found between tire wear particles metals. The concentrations of metals were comparable to previous studies of high traffic areas of Norway, as well as both urban and rural soils in other countries. For the metals, all factors together explained 45 % of the variation observed, with traffic density (11 %) and organic matter content (10 %) as the most important single variables. The analysis of tire wear particles in soils using Pyrolysis Gas chromatography Mass Spectrometry is challenging, and the results presented demonstrate the need for pretreatment to remove organic matter from the samples before analysis.
RESUMO
Rock particles from drilling and blasting during tunnel construction (DB particles) are released to the aquatic environment where they may cause negative toxicological and ecological effects. However, there exists little research on the difference in morphology and structure of these particles. Despite this DB particles are assumed to be sharper and more angular than naturally eroded particles (NE particles), and in consequence cause greater mechanical abrasion to biota. Moreover, morphology of DB particles is assumed to depend on geology, thus depending on where construction takes place different morphologies may be emitted. The objectives in the current study were to investigate the morphological differences between DB and NE particles, and the influence of mineral and elemental content on DB particles. Particle geochemistry and morphology were characterized by inductively coupled plasma mass spectrometry, micro-X-ray fluorescence, X-ray diffraction, environmental scanning electron microscope interfaced with energy dispersive X-ray, stereo microscope, dynamic image analysis and coulter counter. DB particles (61-91% < 63 µm) collected from five different tunnel construction locations in Norway were 8-15% more elongated (lower aspect ratio) than NE particles from river water and sediments, although their angularity was similar (solidity; diff 0.3-0.8%). Despite distinct mineral and elemental characteristics between tunnel construction locations, DB morphology was not explained by geochemical content since only 2-2.1% of the variance was explained. This suggests that particle formation mechanisms during drilling and blasting are more influential of morphology than mineralogy, when working in granite-gneiss terrain. When tunnelling in granite-gneiss terrain, particles with greater elongation than natural particles may enter aquatic systems.
Assuntos
Monitoramento Ambiental , Dióxido de Silício , Tamanho da Partícula , Análise Espectral , Monitoramento Ambiental/métodosRESUMO
The present work focuses on total concentrations of trace elements such as chromium (Cr), manganese (Mn), cobalt (Co), nickel (Ni), copper (Cu), zinc (Zn), arsenic (As), selenium (Se), cadmium (Cd), and lead (Pb) and their operationally defined speciation in surface sediments from three Ethiopian Rift Valley Lakes (Hawassa, Koka, and Ziway). Total concentrations were determined using inductively coupled plasma-mass spectrometer (ICP-MS). A six-step sequential extraction was also applied to evaluate the mobilization potential of these elements. Compared with the consensus-based sediment quality guidelines (SQGs) developed for freshwater ecosystems, the total Zn concentration in sediments from Lakes Hawassa and Ziway, as well as Cr, Ni, and Zn in sediments from Lake Koka, was higher than the probable effect concentration (PEC), suggesting that these elements could have a negative effect on benthic organisms. The sequential extraction results showed that Cd, Mn, and Se were to a certain extent associated with the reversible fractions (F1-F3) in sediments, and thereby more mobile than the other investigated trace elements. Predictions of mobility of trace elements using the distribution coefficients (Kd) values were also in agreement with the sequential extraction results. Furthermore, multivariate statistical analyses showed that redox-sensitive fractions (F4 and F6) and the residual fraction (F7) were the dominant factors controlling most trace element mobility. Finally, applying the Risk Assessment Code (RAC) classification system, results showed that Mn in Lake Koka could pose a high risk, while Cd and Mn in Lake Hawassa as well as Cd, Mn, and Se in Lake Ziway sediments could pose medium risk to benthic organisms.
Assuntos
Arsênio , Metais Pesados , Selênio , Oligoelementos , Poluentes Químicos da Água , Lagos/análise , Oligoelementos/análise , Cádmio/análise , Metais Pesados/análise , Arsênio/análise , Sedimentos Geológicos/análise , Monitoramento Ambiental/métodos , Manganês/análise , Selênio/análise , Níquel/análise , Cobre/análise , Ecossistema , Etiópia , Chumbo/análise , Poluentes Químicos da Água/análise , Cromo/análise , Zinco/análise , Cobalto/análiseRESUMO
Road pollution is one of the major sources of microplastic particles to the environment. The distribution of tire, polymer-modified bitumen (PMB) and tire and road wear particles (TRWP) in different tunnel compartments were explored: road surface, gully-pots and tunnel wash water. A new method for calculating TRWP using Monte Carlo simulation is presented. The highest concentrations on the surface were in the side bank (tire:13.4 ± 5.67;PMB:9.39 ± 3.96; TRWP:22.9 ± 8.19 mg/m2), comparable to previous studies, and at the tunnel outlet (tire:7.72 ± 11.2; PMB:5.40 ± 7.84; TRWP:11.2 ± 16.2 mg/m2). The concentrations in gully-pots were highest at the inlet (tire:24.7 ± 26.9; PMB:17.3 ± 48.8; TRWP:35.8 ± 38.9 mg/g) and comparable to values previously reported for sedimentation basins. Untreated wash water was comparable to road runoff (tire:38.3 ± 10.5; PMB:26.8 ± 7.33; TRWP:55.3 ± 15.2 mg/L). Sedimentation treatment retained 63% of tire and road wear particles, indicating a need to increase the removal efficiency to prevent these from entering the environment. A strong linear relationship (R2-adj=0.88, p < 0.0001) between total suspended solids (TSS) and tire and road wear rubber was established, suggesting a potential for using TSS as a proxy for estimating rubber loads for monitoring purposes. Future research should focus on a common approach to analysis and calculation of tire, PMB and TRWP and address the uncertainties related to these calculations.
Assuntos
Microplásticos , Material Particulado , Material Particulado/análise , Plásticos , Borracha , ÁguaRESUMO
Polycyclic aromatic compounds (PACs) and metals are important contaminants in road runoff. Vital mitigation measures against aquatic contamination from road runoff include the use of sedimentation ponds. However, it has been demonstrated that ecosystems in sedimentation ponds might be affected by road runoff. Sediments from six natural ponds and 27 sedimentation ponds were investigated to determine the environmental risk of contaminants. The amount of traffic on the respective roads associated with the sedimentation ponds was correlated with the environmental concentrations. Quantification included seven metals, the 16 US Environmental Protection Agency polycyclic aromatic hydrocarbons, alkylated PACs, dibenzothiophene, benzo[e]pyrene, and perylene. The environmental risk was assessed according to the European Union Water Framework Directive guidelines. Sedimentation ponds had a higher level of contaminants than natural ponds, and environmental risks were dominated by the concentration of PACs. Alkylated PACs contributed to the environmental risk posed by PACs and should be included in future monitoring. Only Cu and Zn were measured at concentrations above the environmental quality standards (EQSs), while 13 PACs exceeded the EQS. Sediment concentrations of Cu, Zn, and most PACs correlated significantly with the amount of traffic. The sources of PACs were determined by source apportionment ratios between PACs. Alkylation and pyrogenic indices showed that sources in natural ponds were of mostly pyrogenic origin, whereas in sedimentation ponds they were predominantly petrogenic. Asphalt was the probable main source of PACs. A hierarchical clustering technique was used to investigate both the environmental risks and the pattern of PACs in the ponds and revealed that a few sedimentation ponds were not protecting the environment as intended because the upper sediment layers had not been regularly dredged. Environ Toxicol Chem 2022;41:1838-1850. © 2022 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.
Assuntos
Hidrocarbonetos Policíclicos Aromáticos , Compostos Policíclicos , Poluentes Químicos da Água , Ecossistema , Monitoramento Ambiental/métodos , Sedimentos Geológicos/química , Metais , Compostos Orgânicos , Hidrocarbonetos Policíclicos Aromáticos/análise , Poluentes Químicos da Água/análiseRESUMO
The recommended test for assessing if a chemical can be biodegraded in the marine environment is performed according to the Organisation for Economic Cooperation and Development Marine biodegradation test guideline (OECD 306). However, this test is known to generate highly variable test results when comparing interlaboratory test results for the same compound. One reason can be the relatively low bacterial content compared to the inoculum used for OECD readily biodegradation tests (OECD 301). Some of the variability in data obtained from OECD 306 tests can also be due to the flexibility on how to store the seawater inoculum before starting a test. Another variable in the seawater inoculum is the source of seawater used by different laboratories, i.e., geographical location and anthropogenic activities at the source. In this study, the effect of aging seawater and the source of seawater (sample time and depth) were investigated to determine differences in the biodegradation of the reference compound aniline. Aging the seawater before starting the test is recommended in OECD 306 to reduce the background levels of organic carbon in the water. However, it also functions to acclimatize the bacterial community from the environmental source temperature to the test temperature (normally 20 °C). Herein, the microbial community was monitored using flowcytometer during the aging process. As expected, the microbial community changed over time. In one experiment, aging significantly improved the biodegradation of aniline, while in two experiments, there was no significant difference in biodegradation. Interestingly however, there was significant variability in the biodegradation of aniline between sampling seasons and depths, even when all experiments were performed in the same lab, by the same operator and seawater obtained from the same source. This highlights the need for a more robust and consistent microbial inoculum source to reduce variability in seawater biodegradation tests.
Assuntos
Organização para a Cooperação e Desenvolvimento Econômico , Poluentes Químicos da Água , Compostos de Anilina/metabolismo , Bactérias/metabolismo , Biodegradação Ambiental , Água do Mar , Poluentes Químicos da Água/metabolismoRESUMO
According to estimates put forward in multiple studies, tire and road wear particles are one of the largest sources to microplastic contamination in the environment. There are large uncertainties associated with local emissions and transport of tire and road wear particles into environmental compartments, highlighting an urgent need to provide more data on inventories and fluxes of these particles. To our knowledge, the present paper is the first published data on mass concentrations and snow mass load of tire and polymer-modified road wear particles in snow. Roadside snow and meltwater from three different types of roads (peri-urban, urban highway and urban) were analysed by Pyrolysis Gas Chromatography Mass Spectrometry. Tire particle mass concentrations in snow (76.0-14,500 mg/L meltwater), and snow mass loads (222-109,000 mg/m2) varied widely. The concentration ranges of polymer-modified particles were 14.8-9550 mg/L and 50.0-28,800 mg/m2 in snow and meltwater, respectively. Comparing the levels of tire and PMB particles to the total mass of particles, showed that tire and PMB-particles combined only contribute to 5.7% (meltwater) and 5.2% (mass load) of the total mass concentration of particles. The large variation between sites in the study was investigated using redundancy analysis of the possible explanatory variables. Contradictory to previous road studies, speed limit was found to be one of the most important variables explaining the variation in mass concentrations, and not Annual Average Daily Traffic. All identified variables explained 69% and 66%, for meltwater and mass load concentrations, respectively. The results show that roadside snow contain total suspended solids in concentrations far exceeding release limits of tunnel and road runoff, as well as tire particles in concentrations comparable to levels previously reported to cause toxicity effects in organisms. These findings strongly indicate that roadside snow should be treated before release into the environment.
Assuntos
Microplásticos , Plásticos , Monitoramento Ambiental/métodos , Cromatografia Gasosa-Espectrometria de Massas , Polímeros , Neve , Emissões de Veículos/análiseRESUMO
Tire and road wear particles may constitute the largest source of microplastic particles into the environment. Quantification of these particles are associated with large uncertainties which are in part due to inadequate analytical methods. New methodology is presented in this work to improve the analysis of tire and road wear particles using pyrolysis gas chromatography mass spectrometry. Pyrolysis gas chromatography mass spectrometry of styrene butadiene styrene, a component of polymer-modified bitumen used on road asphalt, produces pyrolysis products identical to those of styrene butadiene rubber and butadiene rubber, which are used in tires. The proposed method uses multiple marker compounds to measure the combined mass of these rubbers in samples and includes an improved step of calculating the amount of tire and road based on the measured rubber content and site-specific traffic data. The method provides good recoveries of 83-92% for a simple matrix (tire) and 88-104% for a complex matrix (road sediment). The validated method was applied to urban snow, road-side soil and gully-pot sediment samples. Concentrations of tire particles in these samples ranged from 0.1 to 17.7 mg/mL (snow) to 0.6-68.3 mg/g (soil/sediment). The concentration of polymer-modified bitumen ranged from 0.03 to 0.42 mg/mL (snow) to 1.3-18.1 mg/g (soil/sediment).
Assuntos
Plásticos , Polímeros , Cromatografia Gasosa-Espectrometria de Massas , Hidrocarbonetos , PiróliseRESUMO
The objective of the present work was to obtain scientific information on the ecological health of three freshwater lakes (Awassa, Koka, and Ziway) situated in the Ethiopian Rift Valley by investigating possible trace element contamination accumulated in fish. Accordingly, fish liver and kidney samples were collected from three commercially important fish species (Barbus intermedius, Clarias gariepinus, and Oreochromis niloticus) in the lakes to determine the concentrations of chromium (Cr), manganese (Mn), cobalt (Co), nickel (Ni), copper (Cu), zinc (Zn), arsenic (As), selenium (Se), cadmium (Cd), and lead (Pb), using ICP-MS. Trace element concentrations were generally higher in O. niloticus compared with concentrations in B. intermedius and C. gariepinus. Compared to background values of most freshwater fish species, higher liver concentrations of Cu in C. gariepinus and O. niloticus, Mn in O. niloticus, Co in all except B. intermedius, and Zn in C. gariepinus from Lakes Ziway and Awassa were found. Cr, Co, Ni, Cd, and Pb were enriched in kidney, while Mn, Cu, Zn, As, and Se seems retained in the liver tissues. Assessment of transfer factors indicated that bioaccumulation from water and diet occurred, while uptake from sediments was low. Furthermore, the transfer factor values were generally higher for essential elements compared to the non-essential elements. Multivariate statistical analyses showed that the differences between the trace element levels were generally not significant among the lakes (p = 0.672), while significant differences were found between the fish species (p = 0.042), and between accumulation in kidney and liver (p = 0.002).
Assuntos
Metais Pesados , Oligoelementos , Poluentes Químicos da Água , Animais , Bioacumulação , Monitoramento Ambiental , Rim/química , Lagos , Fígado/química , Metais Pesados/análise , Oligoelementos/análise , Poluentes Químicos da Água/análiseRESUMO
Sedimentation ponds have been shown to accumulate several groups of contaminants, most importantly polycyclic aromatic compounds (PACs) and metals. But also, other urban organic pollutants have shown to be present, including polybrominated diphenyl ethers (PBDEs), organophosphate compounds (OPCs) and benzothiazoles (BTs). This investigation aimed at determining the occurrence of these four groups of contaminants in sedimentation ponds and determine their transport from water/sediment to organisms. PACs, including alkylated PACs, PBDEs; OPCs and BTs were determined in water, sediment, plants, dragonfly larvae and fish from two sedimentation ponds and one reference site. Fish were analysed for PAC metabolites. Overall, higher concentrations of all four pollutant groups were detected in water and sediment from sedimentation ponds compared to two natural lakes in rural environments (reference sites). The concentration difference was highest in sediments, and >20 higher concentration was measured in sedimentation ponds (3.6-4.4 ng/g ww) compared to reference (0.2 ng/g ww) for sum BDE6. For PACs and PBDEs a clear transport from water/sediment to organisms were observed. Fish were the highest trophic level organism (3.5-5) in our study, and all four pollutant groups were detected in fish. For PBDEs a trophic biomagnification (TMF) was found both in sedimentation ponds and reference, but higher concentrations in all matrices were measured in sedimentation ponds. TMF was not calculated for PACs since they are metabolised by vertebrates, but a transfer from water/sediment to organisms was seen. For BTs and OPCs, no consistent transfer to plants and dragonfly larvae could be seen. One OPC and two BTs were detected in fish, but only in fish from sedimentation ponds. It is therefore concluded that sedimentation ponds are hotspots for urban and traffic related contaminants, of which especially PACs and PBDEs are transferred to organisms living there.
RESUMO
Roads are estimated to be the largest source of microplastic particles in the environment, through release of particles from tires, road markings and polymer-modified bitumen. These are all released through the wear and tear of tires and the road surface. During the winter in cold climates, the road surface may freeze and cause icing on the roads. To improve traffic safety during winter, road salt is used for de-icing. Knowledge of microplastic (MP) contamination in road salt has, until now, been lacking. This is contrary to the increasing number of studies of microplastics in food-grade salt. The objective of this study was to investigate if road salt could be an additional source of microplastics to the environment. Fourier-Transform Infrared spectroscopy (FT-IR) and Pyrolysis gas chromatography mass spectrometry (GC-MS) were employed to identify and quantify the polymer content in four types of road salts, three sea salts and one rock salt. The particle number of MP in sea salts (range 4-240â¯MP/kg, mean⯱â¯s.d.â¯=â¯35⯱â¯60â¯MP/kg) and rock salt (range 4-192â¯MP/kg, 424⯱â¯61â¯MP/kg, respectively) were similar, whereas, MP mass concentrations were higher in sea salts (range 0.1-7650⯵g/kg, 442⯱â¯1466⯵g/kg) than in rock salts (1-1100⯵g/kg, 322⯱â¯481⯵g/kg). Black rubber-like particles constituted 96% of the total concentration of microplastics and 86% of all particles in terms of number of particles/kg. Black rubber-like particles appeared to be attributable to wear of conveyer belts used in the salt production. Road salt contribution to MP on state and county roads in Norway was estimated to 0.15â¯t/year (0.003% of total road MP release), 0.07â¯t/year in Sweden (0.008%) and 0.03â¯t/year in Denmark (0.0004-0.0008%) Thus, microplastics in road salt are a negligible source of microplastics from roads compared to other sources.
RESUMO
Road runoff carries a mixture of contaminants that threatens the quality of natural water bodies and the health of aquatic organisms. The use of sedimentation ponds is a nature-based solution for the treatment of road runoff. This study assessed the concentration of polycyclic aromatic hydrocarbons (PAHs) and their alkylated homologues in sediment from seven highway sedimentation ponds and three natural urban ponds. In addition, the study explored the bioaccumulation of PAHs in dragonfly nymphs (Anisoptera). Finally, biota-sediment accumulation factors (BSAFs) were estimated. The results revealed a significant difference in the concentrations of 16 priority PAHs in sediment, with overall higher levels in sedimentation ponds (2,911 µg/kg on average) compared to natural urban ponds (606 µg/kg on average). PAH levels increased substantially once alkylated homologues were considered, with alkylated comprising between 42 and 87% of the total PAH in sediment samples. These results demonstrate the importance of alkylated forms in the environmental assessment of PAHs. The bioaccumulation assessment indicates that dragonfly nymphs bioaccumulate PAHs to a certain degree. It is not clear, however, whether they metabolize PAHs. BSAF results ranged from approx. 0.006 to 10 and indicate that BSAFs can be a powerful tool to determine the functionality of sedimentation ponds.
Assuntos
Alquilantes/química , Monitoramento Ambiental/métodos , Sedimentos Geológicos/análise , Ninfa/metabolismo , Odonatos/metabolismo , Hidrocarbonetos Policíclicos Aromáticos/análise , Poluentes Químicos da Água/análise , Alquilação , Animais , Bioacumulação , Sedimentos Geológicos/química , Ninfa/crescimento & desenvolvimento , Odonatos/crescimento & desenvolvimento , Hidrocarbonetos Policíclicos Aromáticos/química , Poluentes Químicos da Água/químicaRESUMO
The use of stormwater ponds along the highways is shown to be an effective alternative to conventional systems, which are usually sewers. These ponds have the potential to combine their primary function of pollution and peak flow control with the promotion of biodiversity. The present study focuses on comparing natural and highway stormwater ponds in terms of environmental conditions and biodiversity of macroinvertebrate communities. Twelve highway stormwater ponds and nineteen natural ponds (located within or in the vicinity of cultivated landscape) were explored for the number of taxa, community composition, and selected environmental variables: pH, conductivity, pond surface area, the number of ponds within 1 km radius, and the distance to nearest neighboring pond. Highway stormwater ponds showed much higher conductivity, which is a good proxy for chloride concentration and highway pollutants. In addition, the surface area of stormwater ponds was almost twice as big as that of natural ponds. The biological community composition was very different between the two types of ponds, and the number of taxa was slightly higher in the highway stormwater ponds. The most important variables responsible for the variation in the biological community composition were conductivity, pond surface area, and the number of ponds within 1 km radius. This study supports that, in addition to their role in pollution and peak flow control, stormwater ponds have the potential to provide a habitat that may otherwise be unavailable along the highway.
Assuntos
Lagoas , Poluentes Químicos da Água/análise , Agricultura , Biodiversidade , EcossistemaRESUMO
Nowadays, stormwater sedimentation ponds are popular in stormwater management because of their ability to mitigate flooding and treat polluted runoff from e.g. roads. In addition, they may provide other ecosystem services such as biodiversity. These man-made habitats will inevitably be polluted and the organisms living therein may be negatively affected by the chemical cocktail present in both the water and sediment compartments. The present study explored DNA damage in dragonfly nymphs (Odonata, Anisoptera) living in highway sedimentation ponds in comparison with natural ponds. The concentrations of Polycyclic aromatic hydrocarbons (PAHs), alkylated PAHs and metals were also determined in sediment samples from the different ponds. The results showed that DNA damage was significantly higher in dragonfly nymphs living in sedimentation ponds compared to nymphs living in natural ponds. DNA damage was also highly and significantly correlated with the pollution levels in the sediment, i.e., PAH and Zinc. Finally, we report the concentrations of various alkylated PAHs which appeared to be very dominant in the sedimentation ponds. Our results show that there may be a conflict between the sedimentation ponds' primary function of protecting natural water bodies from polluted runoff and their secondary function as habitats for organisms. Overall, we suggest that this must be considered when planning and designing stormwater measures.
Assuntos
Odonatos/efeitos dos fármacos , Odonatos/genética , Poluentes Químicos da Água/toxicidade , Animais , Dano ao DNA/efeitos dos fármacos , Ecossistema , Metais/análise , Metais/toxicidade , Ninfa/efeitos dos fármacos , Hidrocarbonetos Policíclicos Aromáticos/análise , Hidrocarbonetos Policíclicos Aromáticos/toxicidade , Lagoas/química , Poluentes Químicos da Água/análiseRESUMO
ABSTRACT: Stormwater ponds are used to compensate for the adverse effects that road runoff might have on the natural environment. Depending on their design and placement, stormwater ponds can act as both refugia and traps for local biodiversity. To evaluate the impact of stormwater ponds on biodiversity, it is critical to use effective and precise methods for identification of life associated with the water body. DNA metabarcoding has recently become a promising tool for identification and assessment of freshwater biodiversity.Using both morphology and DNA metabarcoding, we analyze species richness and biological composition of samples from 12 stormwater ponds and investigate the impact of pond size and pollution levels in the sediments and water column on the macroinvertebrate community structure.DNA metabarcoding captured and identified more than twice the number of taxa compared to morphological identification. The (dis)similarity of macroinvertebrate community composition in different ponds showed that the ponds appear better separated in the results obtained by DNA metabarcoding, but that the explained variation is higher for the results obtained by morphologically identification, since it provides abundance data.The reliance on morphological methods has limited our perception of the aquatic biodiversity in response to anthropogenic stressors, thereby providing inaccurate information for appropriate design and management of stormwater ponds; these drawbacks can be overcome by DNA metabarcoding. Synthesis and applications. The results indicate that DNA metabarcoding is a useful tool in identifying species, especially Diptera, which are difficult to determine. Application of DNA metabarcoding greatly increases the number of species identified at each sampling site, thereby providing a more accurate information regarding the way the ponds function and how they are affected by management. OPEN PRACTICES: This article has earned an Open Data Badge for making publicly available the digitally-shareable data necessary to reproduce the reported results. The data is available at https://www.ebi.ac.uk/ena/data/view/PRJEB30841.
RESUMO
Constructed stormwater ponds mitigate runoff volumes and pollution, and provide other ecosystem services, such as supporting biodiversity, but these services attracted relatively less attention. The impacts of the pollution levels in the water column and sediments, the physical characteristics of ponds, and the presence of amphibians on the macroinvertebrate community composition and biodiversity were explored in twelve stormwater ponds in Norway. Also, the similarities between macroinvertebrate, zooplankton and plant communities were explored. Most of the taxa displayed in the ordination diagram were positively correlated with the pond size and the number of neighbouring ponds, and negatively correlated with the pollution levels in the water column and sediments. However, no statistically significant impacts on the number of taxa and Shannon index were observed. There were low similarities between the macroinvertebrate and zooplankton community compositions as well as between the plant and macroinvertebrate community compositions in the stormwater ponds. We observed a significant positive correlation between the number of plant and of zooplankton taxa, and a weak non-significant positive correlation between the number of plant and of macroinvertebrate taxa. Overall, the explanatory variables had a significant impact on the community composition, but not on the number of taxa nor Shannon index.
Assuntos
Organismos Aquáticos/classificação , Biodiversidade , Chuva , Filogenia , Chuva/microbiologiaRESUMO
Recently, increased attention has been paid to biodiversity conservation provided by blue-green solutions such as engineered ponds that are primarily established for water treatment and flood control. However, little research has been done to analyse the factors that affect biodiversity in such ponds. The purpose of this study was to evaluate the influence of environmental factors on aquatic biodiversity, mainly macroinvertebrate communities, in road sedimentation ponds in order to provide a foundation for recommendations on aquatic biodiversity conservation. Multivariate statistical methods, including unconstrained and constrained analysis, were applied to examine the relationships between organisms and the water quality as well as physical factors (including plant cover). Stepwise multiple regressions indicated that the most important variables governing the variation in the biological community composition were pond size, average annual daily traffic, metals, chloride, distance to the closest pond from study pond, dissolved oxygen, hydrocarbons, and phosphorus. The presence of most taxa was positively correlated with pond size and negatively correlated with metals. Small ponds with high pollutant loadings were associated with a low diversity and dominated by a few pollution tolerant taxa such as oligochaetes. A comprehensive understanding of impacts of various environmental factors on aquatic biodiversity is important to effectively promote and conserve aquatic biodiversity in such sedimentation ponds. Our results indicate that road sedimentation ponds should be designed large enough, because large ponds are likely to provide a more heterogeneous habitat and thus contain a species rich fauna. In addition, larger ponds seem to be less contaminated due to dilution compared to smaller ponds, thereby maintaining a higher biodiversity. Finally, creating some additional ponds in the vicinity of the sedimentation ponds in areas with few water bodies would increase the connectivity that facilitates the movement of invertebrates between ponds.
RESUMO
A data register study was performed in order to identify the amounts of hazardous substances in products related to motorized transport in Norway during 2012. The hazardous substances were selected from legislative investigations performed by the European Chemicals Agency (ECHA), European Union (EU), and Norwegian Environment Agency (NEA). Information regarding hazardous substances in 52 selected product categories associated with traffic-related activities was obtained from the Norwegian Product Register administrated by the NEA. Substances present on ECHA list of substances of very high concern (SVHC), NEA national priority list, and priority substances under the EU Water Framework Directive (WFD) were given most attention, with substances from ECHA community rolling action plan (CoRAP) also included. Results showed that selected products contained a diverse range of substances that were classified as hazardous to either human or environmental health. The quantities of hazardous substances in the selected products were 120 tons (SVHC), 280 tons (Norway priority list), and 2,400 tons (WFD). It proved difficult to pinpoint these quantities only to traffic-related operations since product categories included compounds used for other activities. However, data illustrate that large quantities of hazardous substances are employed concurrent with being prioritized for reduction/elimination by national and international authorities. A list of substances with annual use in 2012 >1 ton was prepared to aid a prioritization for further actions such as substitution, phasing out, or environmental monitoring. The list contains substances that are toxic to humans, especially as adverse reproductive/carcinogenic agents, and/or pose a threat to the environment.
Assuntos
Monitoramento Ambiental , Substâncias Perigosas/toxicidade , Meios de Transporte , Poluentes Químicos da Água/toxicidade , Carcinógenos/toxicidade , Saúde Ambiental , União Europeia , Humanos , Noruega , Reprodução/efeitos dos fármacos , Água/químicaRESUMO
A combination of silicone rubber extraction and non-target and suspect screening by gas chromatography coupled to high-resolution time-of flight mass spectrometry was used for the identification of compounds in particulate matter (PM). Tunnel PM is a proxy for local road pollution that constitutes a hazard to the urban environment and human health. The use of silicone rubber for the extraction of PM allowed the pre-concentration of a wide range of compounds for non-target analysis while minimising the effects of the sample matrix. As expected, polycyclic aromatic compounds (PACs) constituted the major group of compounds identified, but only 5 of 50 PACs identified were amongst those regularly monitored and many of them were alkylated or contained a heteroatom. Urban markers of contamination such as organophosphate flame-retardants, phthalates, benzothiazoles, musk compounds and a plasticiser were also identified. The level of confidence for the identifications was high based on accurate mass, the pattern of fragmentation and retention. The unequivocal identification of 16 compounds, from all groups, was confirmed by co-chromatography with standards and the compounds semi-quantified. Most of the PACs identified are not regularly monitored, and the hazards they pose are therefore unknown. Some of these PACs are known to be more persistent and mobile in the environment than the EPA PAH16.